MCP3422A2-E/MS - 18-Bit Dual-Input ADC | Microchip
Артикул: MCP3422A2-E/MS ✓ АктивенMCP3422A2-E/MS Обзор
An ADC is an analog-to-digital converter, a semiconductor that transforms a continuously varying voltage into a numeric code for processing by a microcontroller or other digital system. The MCP3422 belongs to the delta-sigma ADC class and the broader data-converter IC hierarchy. Its integrated 2.048 V reference supports a differential input range of plus or minus 2.048 V, while the programmable gain stage allows the converter to scale smaller sensor outputs into the available conversion range.
Key specifications include 18-bit resolution, 2 differential inputs, a 3.75 kSPS conversion rate, a 2.7 V to 5.5 V supply range, and an integrated programmable gain amplifier. The low-noise architecture is suitable for bridge sensors, current measurements, potentiometer positions, temperature signals, and other slowly changing quantities. The 8-MSOP package supports compact PCB layouts without requiring a high pin count.
The delta-sigma conversion architecture continuously samples and filters the input, trading conversion speed for high resolution and good noise performance. The device can be paired with an I2C-compatible host, allowing measured values to be transferred digitally rather than converted by a separate external ADC. Firmware must configure the gain, conversion timing, data rate, channel selection, and operating mode through the device registers.
Typical uses include industrial process monitoring, laboratory instrumentation, battery-powered sensing, environmental measurement, and low-speed control loops. The 3.75 kSPS rate is appropriate for temperature, pressure, strain, and chemical-sensor outputs that change over seconds or minutes. It is not the preferred choice for high-bandwidth waveform capture, where a substantially faster SAR or other converter would be more appropriate.
PCB implementation should keep analog input traces short, provide a quiet ground return, place input filtering close to the converter, and decouple the supply pins. Input filtering, common-mode range, source impedance, and reference accuracy must be evaluated together because each can influence the achievable code accuracy. The manufacturer MCP3422 product page and datasheet provide the authoritative pin descriptions, register map, and application guidance.
This product record combines the manufacturer specifications with package, application, comparison, and replacement guidance. It also identifies the exact family variants that can be evaluated when a different gain setting, conversion-rate option, or package arrangement is required. Use the Request a Quote form on this page for current commercial availability, and confirm lifecycle and manufacturing status with Microchip Technology before committing a production design.
Аналоги без доработки для MCP3422A2-E/MS — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
MCP3422A1T-E/MS
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCP3422A5T-E/MS
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCP3422A7T-E/MS
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCP3422A2-E/MC
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCP3422A2-E/MS Максимальные параметры и электрические характеристики
| ADC Type | 18-bit delta-sigma ADC |
| Разрешение | 18 bit |
| Input Channels | 2 differential inputs |
| Частота дискретизации | 3.75 kSPS |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Internal Reference Voltage | 2.048 V |
| Differential Input Range | +/-2.048 V |
| Programmable Gain Amplifier | Integrated, programmable |
| Output Interface | I2C |
| Корпус | 8-MSOP |
| Тип монтажа | Surface mount |
| Диапазон рабочих температур | -40 C to +125 C |
Руководство по цоколевке MCP3422A2-E/MS в корпусе 8-msop
Цоколевка для MCP3422A2-E/MS (корпус 8-msop). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для MCP3422A2-E/MS.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MCP3422A2-E/MS подходит для 6 применениеs: Precision Temperature Measurement, Industrial Pressure and Load Monitoring, Battery-Powered Environmental Sensing, Laboratory Instrument Front End, Current and Power Monitoring, Precision Potentiometer Position Readout.
Precision Temperature Measurement
The MCP3422A2-E/MS is appropriate for slow temperature signals generated by RTDs, thermistors, or low-output voltage sensors. Its 18-bit resolution and integrated programmable gain amplifier provide substantial measurement range for small sensor outputs, while the 3.75 kSPS conversion rate is more than sufficient for thermal systems that update over seconds. Place the sensor return path close to the converter, use differential inputs to reduce common-mode pickup, and select an external filter that preserves the required settling time. The 2.7 V to 5.5 V operating range also supports both 3.3 V and 5 V instrumentation systems. Confirm the sensor excitation scheme and common-mode limits before finalizing the input network.
Рекомендуется
Industrial Pressure and Load Monitoring
The MCP3422A2-E/MS can digitize low-level differential outputs from pressure transducers, load cells, and strain-gauge bridges. The two differential inputs help isolate the measured sensor voltage, and the programmable gain amplifier can bring millivolt-scale outputs into the converter's usable range. Its delta-sigma architecture favors low-frequency process measurements where conversion latency is less important than resolution. The 2.048 V internal reference provides a fixed conversion basis, although a ratiometric bridge may require careful reference strategy for accurate engineering-unit scaling. Use short shielded input routes, stable excitation, and datasheet-recommended filtering to preserve accuracy and reject industrial noise.
Рекомендуется
Battery-Powered Environmental Sensing
The MCP3422A2-E/MS fits environmental monitoring nodes that measure humidity, gas, pH, or other slow sensor outputs. Its 2.7 V minimum supply supports low-voltage systems, while 18-bit resolution helps retain useful detail in small sensor signals. The 3.75 kSPS rate avoids wasting conversion activity on nearly static measurements and supports periodic sampling by the host controller. Energy use must still be evaluated using the selected data rate, PGA gain, operating mode, and host duty cycle from the manufacturer datasheet. Place input protection close to the connector, use low-leakage components, and confirm that sensor excitation and analog filtering do not dominate the node's standby-current budget.
Рекомендуется
Laboratory Instrument Front End
The MCP3422A2-E/MS can serve as the measurement front end in a laboratory instrument that records slow analog variables such as voltage, current, or controlled test outputs. Its 18-bit conversion resolution and differential inputs are useful when the measured quantity is small and accuracy matters more than acquisition speed. The internal 2.048 V reference simplifies standalone measurement, while the PGA allows the input to be matched to the available converter range. For laboratory use, isolate sensitive analog routing from digital activity, use a quiet ground strategy, and calibrate offset and gain after installation. The 3.75 kSPS rate should be checked against the instrument's settling time and user experience requirements.
Рекомендуется
Current and Power Monitoring
The MCP3422A2-E/MS can measure small differential voltage drops produced by a current-sense resistor when the shunt output remains within the ADC's electrical limits. The integrated PGA is useful for amplifying millivolt-level shunt voltages, while differential sampling reduces sensitivity to voltage common to both measurement nodes. Conversion results can support power management, battery discharge analysis, or equipment diagnostics. The design must include the shunt's common-mode behavior, amplifier input limits, filtering, and the converter's operating input range. Because the MCP3422A2-E/MS is optimized for relatively slow measurements, use a faster ADC when current transients must be captured with high temporal resolution.
Рекомендуется
Precision Potentiometer Position Readout
The MCP3422A2-E/MS is suitable for high-resolution position readout from potentiometers and other slowly moving resistive dividers when ratiometric accuracy is adequate for the application. Its 18-bit resolution can extract more detail from the divider voltage than a lower-resolution converter, while the 3.75 kSPS rate is appropriate for manual controls, valve position, or slow actuator feedback. Connect the divider across the appropriate supply and ground references, then measure the wiper with the configured differential or single-ended input arrangement described in the datasheet. Verify input settling, resistance loading, leakage, and the available code range in the actual divider network before treating the displayed resolution as usable position accuracy.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MCP3422A2-E/MS — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MCP3422A1T-E/MS | MCP3422A5T-E/MS | MCP3422A7T-E/MS | MCP3422A2-E/MC |
|---|---|---|---|---|---|
| Package | 8-MSOP | 8-MSOP | 8-MSOP | 8-MSOP | 8-MSOP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Converter Architecture | Delta-sigma ADC | Delta-sigma ADC | Delta-sigma ADC | Delta-sigma ADC | Delta-sigma ADC |
| Resolution | 18 bit | 18 bit | 18 bit | 18 bit | 18 bit |
| Input Configuration | 2 differential inputs | 2 differential inputs | 2 differential inputs | 2 differential inputs | 2 differential inputs |
| Internal Reference | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V |
| Programmable Gain Amplifier | Integrated | Integrated | Integrated | Integrated | Integrated |
| Digital Interface | I2C | I2C | I2C | I2C | I2C |
Ключевые отличия
- Exact A2 configuration in a compact 8-MSOP package (против MCP3422A7T-E/MS)
- Integrated reference and PGA reduce external analog support components (против MCP3422A5T-E/MS)
- Differential two-channel architecture supports low-level sensor measurement (против MCP3422A1T-E/MS)
Заметки по проектированию
Place the MCP3422A2-E/MS close to the analog source and route the differential inputs as a compact, matched pair. Keep switching-current paths and digital clock traces away from the input nodes. Provide a direct ground return for the source and use the capacitor values and placement shown in the manufacturer datasheet. The exposed relationships between input impedance, PGA gain, filtering, and settling time determine whether the nominal 18-bit resolution can be obtained in the final board.
Do not select the input filter solely from a desired cutoff frequency. Include the sensor output impedance, ADC input impedance, PGA gain, and allowed settling time when designing the network. For slow sensors, a sufficiently large RC time constant can suppress noise, but excessive capacitance or resistance may prevent full settling within the selected conversion cycle. Verify the complete acquisition chain against the MCP3422 timing and noise characteristics in the manufacturer datasheet.
Decouple the 2.7 V to 5.5 V supply at the MCP3422A2-E/MS with the components and layout required by the manufacturer datasheet. Keep the analog section on a quiet branch if other circuitry shares the supply. The internal 2.048 V reference is convenient, but overall measurement accuracy still depends on reference behavior, supply stability, input common-mode limits, and source resistance. Review these constraints together instead of assuming 18-bit resolution alone guarantees equivalent accuracy.
Информация о соответствии
Compliance attributes were not explicitly stated in the available manufacturer-page and distributor excerpts. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals documentation for the exact orderable MPN with Microchip Technology.