Microchip Technology

MCP3426A3-E/MS - 16-Bit Dual-Channel ADC | Microchip

Артикул: MCP3426A3-E/MS ✓ Активен
2.7 V to 5.5 V Vdss 8-MSOP, 3.00 mm width Package
MOQ: 1 |

MCP3426A3-E/MS Обзор

The Microchip Technology MCP3426A3-E/MS is a 16-bit, dual-input sigma-delta analog-to-digital converter operating at 15 samples per second, housed in an 8-MSOP package. Its digital supply range is 2.7 V to 5.5 V, and its operating temperature range is -40 °C to +125 °C.

An analog-to-digital converter, or ADC, converts an analog input voltage into a digital value that a microcontroller, embedded controller, or data-acquisition system can process. The MCP3426 belongs to the sigma-delta ADC family, where the analog input is continuously sampled and converted through delta-sigma modulation and digital filtering. This architecture is commonly used for relatively slow, precision-oriented measurements that do not require high-frequency sampling.

The MCP3426A3-E/MS combines a 16-bit conversion resolution with two analog input channels and a 15 sps conversion rate. This operating point is suited to slowly varying sensor signals where high resolution and noise-limited measurement are more important than rapid sampling. Operation from a 2.7 V to 5.5 V digital supply supports both 3.3 V and 5 V system architectures, while the industrial temperature rating allows deployment across a broad range of ambient conditions.

The device uses a sigma-delta conversion architecture that separates analog measurement from digital filtering. In a typical circuit, external analog components condition each input before it reaches the converter, while a microcontroller reads the converted result through a serial interface. The -40 °C to +125 °C operating range and 8-MSOP surface-mount construction make the device suitable for compact industrial, instrumentation, and embedded measurement systems.

Typical uses include temperature monitoring, pressure and strain-sensor acquisition, potentiometer position measurement, and low-frequency process-control inputs. These applications benefit from the 16-bit resolution when the measured signal changes slowly and system noise has been controlled through shielding, grounding, filtering, and careful PCB layout.

The principal design consideration is the relationship between input accuracy, analog reference quality, and the conversion cycle. The 15 sps rate should be matched to the physical signal bandwidth; oversampling a fast or noisy signal cannot recover information that the input network has already filtered out. Reference and supply bypassing must also be placed close to the device pins.

This product page combines the MCP3426A3-E/MS electrical characteristics, package information, pricing references, same-family drop-in alternatives, and application-focused engineering guidance to support component selection, PCB planning, and BOM qualification.

Аналоги без доработки для MCP3426A3-E/MS — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с MCP3426A3-E/MS (тот же форм-фактор и посадочное место) — отличается по Package, Differential Input Range, Operating Temperature Range, ADC Type, Input Architecture.

Microchip Technology
Package: 8-pin MSOP
Differential Input Range: ±2.048 V
Operating Temperature Range: -40°C to +125°C
Microchip Technology
Package: 8-pin MSOP
Differential Input Range: ±2.048 V differential
Microchip Technology
Package: 8-MSOP
Differential Input Range: ±2.048 V
ADC Type: Sigma-delta ADC
Microchip Technology
Package: 8-pin MSOP
Differential Input Range: -2.048 V to +2.048 V
Operating Temperature Range: -55 °C to +125 °C
Microchip Technology
Package: 8-pin MSOP
Differential Input Range: ±2.048 V
Operating Temperature Range: -40°C to +125°C
Microchip Technology
Package: 8-pin MSOP
Differential Input Range: ±2.048 V
Input Architecture: Differential inputs

MCP3426A7-E/MS

✅ Прямая замена
Microchip Technology
📦 8-MSOP
16 bit · 2 channels · Differential inputs · 1-channel-per-input delta-sigma architecture · 15 samples per second · 2.7 V to 5.5 V · 3.3 V or 5 V · 2.048 V

Уточнить цену

Открыть даташит →

MCP3426A3T-E/MS

✅ Прямая замена
📦 8-MSOP
Same 16-bit, dual-channel, 15 sps electrical configuration and 8-MSOP pinout; production packing method differs.

📋 Справочный аналог (нет в каталоге)

MCP3426A5-E/MS

✅ Прямая замена
Microchip Technology
📦 8-MSOP
16-bit delta-sigma ADC · 2 channels · Differential inputs · 15 samples/s · 2.048 V · -2.048 V to +2.048 V · 2.7 V to 5.5 V · -55 °C to +125 °C

Уточнить цену

Открыть даташит →

MCP3426A0-E/MS

✅ Прямая замена
Microchip Technology
📦 8-MSOP
16 bit · 2 channels · 2 differential inputs · 1-channel sigma-delta conversion per differential input · 15 SPS · 2.048 V · ±2.048 V · I2C

Уточнить цену

Открыть даташит →

MCP3426A1-E/MS

✅ Прямая замена
Microchip Technology
📦 8-MSOP
16 bit · 2 differential inputs · Delta-sigma sigma-delta ADC · 15 SPS · 2.7 V to 5.5 V · 2.048 V · ±2.048 V differential · 8-pin MSOP

Уточнить цену

Открыть даташит →

MCP3426A6-E/MS

✅ Прямая замена
Microchip Technology
📦 8-MSOP
16-bit delta-sigma ADC · 2 differential channels · Up to 16 bits · 15 samples/s · Differential input · 2.048 V · ±2.048 V · 3.3 V or 5 V

Уточнить цену

Открыть даташит →

MCP3426A3-E/MS Максимальные параметры и электрические характеристики

ADC Type Sigma-delta analog-to-digital converter
Разрешение 16 bit
Number of Input Channels 2 channels
Conversion Rate 15 samples/s
Digital Supply Voltage 2.7 V to 5.5 V
Диапазон рабочих температур -40 °C to +125 °C
Корпус 8-MSOP, 3.00 mm width
Тип монтажа Surface mount
Number of Terminals 8 terminals
Terminal Form Gull wing
Package Shape Square
Automotive Classification Automotive temperature grade
Статус RoHS unknown
REACH Status unknown

Руководство по цоколевке MCP3426A3-E/MS в корпусе square

Цоколевка для MCP3426A3-E/MS (корпус square). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.

Схема цоколевки корпуса square для MCP3426A3-E/MS

Нет подробных данных о распиновке для MCP3426A3-E/MS.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

MCP3426A3-E/MS подходит для 6 применениеs: Industrial Temperature Sensing, Pressure and Strain Measurement, Battery-Powered Instrumentation, Process Control and Monitoring, Precision Potentiometer Readout, Environmental and Sensor Monitoring.

🏭

Industrial Temperature Sensing

The MCP3426A3-E/MS fits slow industrial temperature measurements because it combines a 16-bit conversion resolution with a 15 samples-per-second rate and an operating range of -40 °C to +125 °C. Place the converter in the measurement path after a conditioned bridge or thermistor interface, then read the digital result through its serial interface. The 15 sps rate is appropriate for thermal signals that change gradually rather than high-speed transients. Its 2.7 V to 5.5 V digital supply also permits integration into both 3.3 V and 5 V controller platforms.

🏭

Pressure and Strain Measurement

The MCP3426A3-E/MS can digitize conditioned pressure-cell or strain-gauge outputs where measurement accuracy over time matters more than acquisition bandwidth. Its 16-bit format provides 65,536 numerical levels, while the 15 samples-per-second rate is appropriate for slow pressure loading, valve position, and mechanical deformation. The dual-input arrangement can monitor a sensor signal and a reference channel when the application requires drift or offset compensation. Signal conditioning, input filtering, and reference stability remain central to preserving the converter's useful resolution.

📱

Battery-Powered Instrumentation

The MCP3426A3-E/MS is suitable for portable instrumentation that records slowly changing physical quantities. Its 15 samples-per-second operating point avoids the data volume associated with a fast converter, while the 2.7 V minimum digital supply supports low-voltage embedded systems. The device can capture conditioned outputs from resistive, capacitive, or bridge-based sensors in a compact 8-MSOP footprint. Low-power designs should still evaluate the complete current-consumption profile and disable or duty-cycle the acquisition chain when longer battery life is required.

⚡

Process Control and Monitoring

The MCP3426A3-E/MS supports supervisory process measurements such as tank level, valve position, and slowly changing line pressure. Two analog channels allow a controller to acquire two related process variables, and the 16-bit result format is useful when the measured quantity has a narrow engineering range. The 15 samples-per-second rate provides repeated readings for control and alarm logic without the overhead of high-rate acquisition. Industrial implementation should place input conditioning close to the converter and maintain a clean reference and supply network.

🔧

Precision Potentiometer Readout

The MCP3426A3-E/MS is appropriate for high-resolution position readout from a potentiometer or resistive divider where the mechanical movement is slow. Sixteen-bit resolution produces a fine digital increment across the selected measurement range, while the 15 samples-per-second rate supports continuous monitoring and averaging rather than only a single static reading. The 8-MSOP package helps reduce board area in compact control panels and test fixtures. Mechanical contact resistance, wiring noise, and excitation stability should be included in the error budget.

🧩

Environmental and Sensor Monitoring

The MCP3426A3-E/MS can be used in environmental monitoring systems that measure humidity, light, pressure, or chemical-sensor outputs after analog conditioning. Its dual-channel architecture can combine a primary sensor with a reference or second probe, while the 15 samples-per-second rate is well matched to slowly varying environmental conditions. The 2.7 V to 5.5 V digital supply range supports embedded monitoring electronics, and the -40 °C to +125 °C operating range supports industrial deployments. Field accuracy still depends on sensor calibration and protection from condensation or transient damage.

What is the MCP3426A3-E/MS?
The MCP3426A3-E/MS is a 16-bit, dual-input, sigma-delta analog-to-digital converter with a maximum conversion rate of 15 samples per second. According to the Microchip Technology datasheet, the device operates from a 2.7 V to 5.5 V digital supply and is packaged in an 8-MSOP for surface-mount assembly. It is intended for precision measurements from relatively slow analog sensors rather than high-speed waveform acquisition.
How many channels and bits does MCP3426A3-E/MS have?
The MCP3426A3-E/MS provides two analog input channels with a 16-bit conversion resolution. According to the Microchip Technology datasheet, the converter operates at 15 samples per second and accepts a digital supply voltage from 2.7 V to 5.5 V. The dual-channel configuration permits one ADC to monitor two related analog inputs, while the 16-bit format provides 65,536 discrete digital codes.
What is the conversion rate of MCP3426A3-E/MS?
The MCP3426A3-E/MS performs conversions at 15 samples per second. According to the Microchip Technology datasheet, this rate is appropriate for slowly changing sensor signals such as temperature, pressure, strain, or resistive position measurements. It is not optimized for capturing high-frequency waveforms, so the input bandwidth and required sampling rate should be checked before assigning the converter to an acquisition task.
What supply voltage does MCP3426A3-E/MS use?
The MCP3426A3-E/MS accepts a 2.7 V to 5.5 V digital supply. According to the Microchip Technology datasheet, this range supports 3.3 V and 5 V digital systems. The separate analog supply requirement and recommended voltage levels should be checked against the complete device electrical specification before finalizing the power architecture and bypass-capacitor values.
Where can I download the MCP3426A3-E/MS datasheet PDF?
The official MCP3426A3-E/MS datasheet is available through Microchip Technology's product page for the MCP3426 family. The manufacturer datasheet contains the authoritative pin descriptions, electrical limits, recommended application circuit, interface timing, and conversion characteristics. Use that document during PCB layout and firmware development, particularly when assigning the analog inputs, reference, supply, and serial interface pins.
Where is the MCP3426A3-E/MS pinout?
The MCP3426A3-E/MS uses an 8-MSOP footprint, and its complete numbered pin assignment is defined in the Microchip Technology pin-description table. The two analog channels, digital interface, supply connections, reference connection, and ground pins must be assigned from that table before schematic capture. The 8-MSOP package should not be confused with the physically related 8-TSSOP package without checking the manufacturer drawing.
Where can I buy MCP3426A3-E/MS online?
The MCP3426A3-E/MS can be requested through the Request a Quote form on this XAIPART product page. Submit the required quantity, shipment destination, and target date so the exact MCP3426A3-E/MS order can be reviewed. The quote process avoids presenting a static price or availability claim that may no longer reflect current inventory and manufacturing conditions.
What is the price of MCP3426A3-E/MS?
Current pricing for MCP3426A3-E/MS should be obtained through the Request a Quote form on this page. The form accepts the required quantity and delivery information needed to prepare a current quotation for the exact MPN. Because pricing and inventory can change by quantity, packaging, and market conditions, use the quote response rather than a historical unit-price figure for purchasing decisions.
What is the lead time for MCP3426A3-E/MS?
The current lead time for MCP3426A3-E/MS should be confirmed through the Request a Quote form on this page. Include the annual and per-order quantities, required delivery date, and approved packaging method with the request. A lead-time confirmation for the exact MPN is more useful than a generic device-family estimate when production material is being scheduled.
Is MCP3426A3-E/MS in stock?
Current stock for MCP3426A3-E/MS should be requested through the Request a Quote form on this page. Provide the required order quantity and target date so an availability confirmation can be prepared for the exact device. Distributor inventory may move independently of Microchip Technology's production status, so stock confirmation and lead-time confirmation are both necessary for production planning.
MCP3426A3-E/MS vs MCP3426A7-E/MS - which is better for my design?
The MCP3426A7-E/MS is the closest documented same-package alternative when an identical-footprint option is required, while the MCP3426A3-E/MS remains the choice when 15 samples per second is specifically required. According to Microchip Technology's family documentation, both devices occupy the same 8-MSOP package and share the 16-bit dual-channel architecture. Final selection should confirm operating-mode requirements and pin-level behavior against the manufacturer datasheet.
When should I choose MCP3426A3-E/MS over MCP3426A7-E/MS?
Choose the MCP3426A3-E/MS when the acquisition system requires a 16-bit, dual-channel sigma-delta converter operating at 15 samples per second in an 8-MSOP package. Choose MCP3426A7-E/MS when its documented operating mode better matches the measurement task and its pin configuration remains unchanged. The decision should prioritize conversion-rate requirements, operating mode, reference arrangement, and verified register compatibility.
What is the best drop-in replacement for MCP3426A3-E/MS?
The best drop-in replacement is the same-family device whose package, pin arrangement, electrical limits, and conversion behavior have all been verified. MCP3426A7-E/MS, MCP3426A3T-E/MS, MCP3426A5-E/MS, and MCP3426A0-E/MS appear in the cross-reference results for this family. A candidate should be accepted only after checking its conversion rate, operating mode, interface timing, and production suitability in the Microchip Technology datasheet.
Can MCP3426A5-E/MS replace MCP3426A3-E/MS without PCB changes?
The MCP3426A5-E/MS uses the same 8-MSOP family package, but PCB footprint compatibility alone does not establish functional interchangeability. Its conversion-rate option and operating behavior must be compared with the 15 samples per second MCP3426A3-E/MS before substitution is approved. Review the manufacturer pin table, recommended application circuit, timing, and acquisition timing in the firmware.
What are the key specifications of MCP3426A3-E/MS that engineers should know?
The MCP3426A3-E/MS combines a 16-bit resolution, two analog input channels, a 15 samples-per-second conversion rate, a 2.7 V to 5.5 V digital supply, and an operating range of -40 °C to +125 °C. According to the Microchip Technology datasheet, it is an 8-MSOP surface-mount sigma-delta ADC. These values position the device for slow, precision-oriented sensor and instrumentation measurements.
Is there a Microchip Technology equivalent for MCP3426A3-E/MS?
The MCP3426A7-E/MS and other documented MCP3426 family members are the relevant Microchip Technology drop-in candidates because they use the same 8-MSOP package. Their conversion-rate and operating-mode settings differ, so the closest functional replacement must be selected for the intended acquisition timing. Use the Microchip Technology cross-reference search and datasheet to confirm pin and behavior compatibility before production release.

Справочные инженерные данные для MCP3426A3-E/MS — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the MCP3426A3-E/MS when the design requires a 16-bit, two-channel sigma-delta ADC operating at 15 samples per second from a 2.7 V to 5.5 V digital supply in an 8-MSOP package. It is a strong fit for slowly varying temperature, pressure, strain, potentiometer, and environmental sensor measurements where repeatability and resolution matter more than waveform capture. MCP3426A3T-E/MS offers the closest electrical match when its approved production packing method suits the assembly process. Consider MCP3426A7-E/MS when its operating mode better aligns with the measurement sequence, and review MCP3426A5-E/MS or MCP3426A0-E/MS only when their conversion timing is acceptable. For every substitution, verify the manufacturer pin table, interface timing, configuration behavior, reference arrangement, and thermal limits rather than relying on package appearance alone.

Сравнение с аналогами

Параметр Этот товар MCP3426A7-E/MS MCP3426A3T-E/MS MCP3426A5-E/MS MCP3426A0-E/MS MCP3426A1-E/MS
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 8-MSOP 8-MSOP 8-MSOP 8-MSOP 8-MSOP 8-MSOP
ADC Resolution 16 bit 16 bit 16 bit 16 bit 16 bit 16 bit
Number of Input Channels 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels
Conversion Architecture Sigma-delta Sigma-delta Sigma-delta Sigma-delta Sigma-delta Sigma-delta
Mounting Type Surface mount Surface mount Surface mount Surface mount Surface mount Surface mount

Ключевые отличия

  • Defined 15 samples-per-second operating point (против MCP3426A5-E/MS)
  • Exact electrical configuration match with the same package (против MCP3426A3T-E/MS)
  • Dual-channel measurement in a compact 8-MSOP footprint (против MCP3426A0-E/MS)
  • Industrial temperature coverage (против MCP3426A7-E/MS)

Заметки по проектированию

Place the device's supply bypass and reference-decoupling components directly beside their corresponding pins, with short, low-inductance traces. Keep the analog input routing away from digital clock and serial-interface traces. The 8-MSOP footprint has limited lead spacing, so input and ground routing should follow the pin-description table and recommended layout in the Microchip Technology datasheet rather than relying on a generic MSOP template.

The 15 samples-per-second conversion rate is appropriate for slowly varying signals, but it does not remove the need for an input filter. Select filter and settling components for the source impedance and required bandwidth, and allow the analog front end to settle before interpreting a result as accurate. Differential, common-mode, and reference error should be evaluated together because the nominal 16-bit resolution does not guarantee 16-bit total system accuracy.

Do not substitute an 8-TSSOP footprint for the specified 8-MSOP package without checking the manufacturer land pattern and pin dimensions. Also confirm the selected family member's conversion rate and operating mode before using an A-series variant as a replacement. A shared package reduces PCB work, but it does not replace verification of timing, configuration registers, reference behavior, and acquisition sequencing.

The MCP3426A3-E/MS supports a 2.7 V to 5.5 V digital supply, but the complete system still needs clean analog and reference rails. Verify that supply ripple, digital switching activity, and reference variation do not dominate the converter's usable measurement resolution. For portable systems, calculate the average acquisition energy using the converter's measured operating current, duty cycle, and the number of readings required by the application.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The device is identified as automotive temperature grade, but AEC-Q100 qualification and environmental compliance declarations require confirmation from the manufacturer.

Данные проверены: 2026-11-20 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

MCP3426A3-E/MS datasheet MCP3426A3-E/MS pinout MCP3426A3-E/MS datasheet pdf MCP3426A3-E/MS 16 bit ADC MCP3426A3-E/MS 15 sps MCP3426A3-E/MS 8-MSOP MCP3426A3-E/MS equivalent MCP3426A3-E/MS replacement MCP3426A3-E/MS cross reference MCP3426A3-E/MS vs MCP3426A7-E/MS MCP3426A3-E/MS price MCP3426A3-E/MS stock Microchip MCP3426A3-E/MS MCP3426A3-E/MS sensor measurement

Связанные компоненты & термины

Microchip Technology MCP3426A3-E/MS MCP3426A7-E/MS MCP3426A3T-E/MS MCP3426A5-E/MS MCP3426A0-E/MS MCP3426A1-E/MS MCP3426A6-E/MS analog-to-digital converter ADC sigma-delta ADC delta-sigma modulator 16-bit resolution dual-channel ADC 8-MSOP surface mount SMD 2.7 V to 5.5 V supply 15 samples per second temperature sensor measurement pressure sensor measurement strain-gauge measurement potentiometer readout industrial instrumentation
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ