MCP6021-E/MS - 10MHz RRO Op Amp | Microchip | MSOP-8
Артикул: MCP6021-E/MS ✓ АктивенMCP6021-E/MS Обзор
An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. The MCP6021 belongs to the broader hierarchy of operational amplifier, analog amplifier IC, and signal-conditioning semiconductor. Rail-to-rail inputs allow the amplifier to operate with input voltages near the lower and upper supply limits, while rail-to-rail outputs improve output swing. These characteristics make the device useful for sensors, portable instrumentation, audio signal paths, and low-voltage data-acquisition systems.
Key features include a 10 MHz gain-bandwidth product, typical operating current of 1.0 mA, and typical input offset voltage below 0.5 mV. The Microchip MCP6021 family also provides low bias current, high open-loop gain, and general-purpose operation across industrial and extended-temperature options. The MCP6021-E/MS suffix identifies the extended-temperature version in the 8-lead MSOP configuration, making it suitable for industrial equipment when the circuit operates within the manufacturer-specified temperature limits.
The 10 MHz bandwidth supports closed-loop gains and signal frequencies that would be difficult to handle with a slow precision amplifier. At the same time, the 1.0 mA typical operating current keeps the amplifier suitable for portable and embedded systems. Designers should account for amplifier stability, output drive, load impedance, input common-mode range, and rail-to-rail output behavior when selecting feedback and external compensation networks.
Typical uses include buffering sensor outputs, amplifying low-level analog signals, active filtering, portable test equipment, and audio or communications interface circuits. The low supply current benefits battery-operated equipment, while the 10 MHz bandwidth provides useful responsiveness for moderate-frequency signal conditioning.
PCB implementation requires careful decoupling and stable return paths. Place the power-supply bypass capacitor close to the positive supply and ground pins, route the input and output traces away from switching nodes, and use a solid ground plane. Check capacitive-load stability and output-swing limits against the actual load before committing to the design.
This page combines the manufacturer device information, MPN packaging details, comparison options, and practical implementation guidance to support component selection, PCB planning, and replacement evaluation.
Аналоги без доработки для MCP6021-E/MS — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
MCP6021-I/MS
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCP6021T-E/MS
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCP6021-E/MS Максимальные параметры и электрические характеристики
| Amplifier Type | Single general-purpose operational amplifier |
| Gain-Bandwidth Product | 10 MHz |
| Typical Operating Current | 1.0 mA |
| Typical Input Offset Voltage | <0.5 mV |
| Supply Voltage Range | 2.5 V to 5.5 V |
| Корпус | 8-lead MSOP |
| Package Width | 3.00 mm |
| Тип монтажа | Surface mount |
Конфигурация выводов MCP6021-E/MS
| Контакт 1 | NC — Not connected |
| Контакт 2 | IN- — Inverting input |
| Контакт 3 | IN+ — Non-inverting input |
| Контакт 4 | V- — Negative power supply |
| Контакт 5 | NC — Not connected |
| Контакт 6 | OUT — Analog output |
| Контакт 7 | V+ — Positive power supply |
| Контакт 8 | NC — Not connected |
Типичное применение
MCP6021-E/MS подходит для 6 применениеs: Battery-Powered Sensor Signal Conditioning, Industrial Instrumentation Buffer, Low-Voltage Audio Preamp, Active Analog Filter, Portable Medical Monitoring Front End, Communications Interface Buffer.
Battery-Powered Sensor Signal Conditioning
The MCP6021-E/MS is suitable for conditioning sensor outputs in portable, battery-powered equipment because its typical operating current is 1.0 mA and its supply range begins at 2.5 V. Rail-to-rail input capability supports signals positioned near either supply rail, while the 10 MHz gain-bandwidth product provides useful response for moderate-frequency sensor dynamics. Place the amplifier between the sensor and an ADC or controller, use a low-noise bypass capacitor at the supply pins, and verify the actual input common-mode range, output swing, and capacitive-load stability for the selected operating point.
Рекомендуется
Industrial Instrumentation Buffer
The MCP6021-E/MS can buffer low-level instrumentation signals in industrial control systems where a 2.5 V to 5.5 V supply and extended-temperature ordering option are required. Its typical offset voltage below 0.5 mV limits input-referred error at low signal levels, and the 10 MHz gain-bandwidth product supports moderate-frequency process signals. Use the amplifier as a voltage follower or a low-gain stage, route the input directly to the non-inverting or inverting terminal, and return the feedback network over a quiet ground plane to reduce offset and noise pickup.
Рекомендуется
Low-Voltage Audio Preamp
The MCP6021-E/MS is appropriate for a low-voltage audio preamplifier when low supply current and moderate bandwidth are more important than high-voltage output capability. Its 10 MHz gain-bandwidth product provides ample response for audio-band amplification, and the 1.0 mA typical operating current supports portable audio hardware. Connect the input through a defined source resistance, select a feedback gain compatible with the device's stability characteristics, and check the output waveform at the maximum planned signal level. Headphone or speaker loads require separate drive circuitry because an operational amplifier is not a power-output stage.
Рекомендуется
Active Analog Filter
The MCP6021-E/MS is useful in an active filter built around a 2.5 V to 5.5 V analog rail because its 10 MHz gain-bandwidth product provides more open-loop bandwidth than many low-power precision amplifiers. It can implement first- and higher-order low-pass, high-pass, or band-pass networks when component tolerances and phase margin are considered carefully. Keep passive components close to the amplifier pins, use an established filter topology with supported noise-gain values, and simulate tolerance and load effects. The rail-to-rail output characteristic helps preserve dynamic range when the signal approaches the available output swing.
Рекомендуется
Portable Medical Monitoring Front End
The MCP6021-E/MS can form the analog front end of a portable monitoring device when its extended-temperature ordering option, 1.0 mA typical current, and less than 0.5 mV typical offset voltage fit the signal chain. The amplifier can buffer a low-level sensor or condition a signal before digitization. Its 10 MHz bandwidth avoids limiting moderate-frequency physiological signals, although system noise, protection components, patient safety requirements, and electrode-source impedance determine the final suitability. Validate the complete analog path for offset, drift, noise, common-mode limits, and fault behavior before production use.
Рекомендуется
Communications Interface Buffer
The MCP6021-E/MS is suitable for low-voltage communications interface buffering when the signal remains within its specified input and output limits. The 10 MHz gain-bandwidth product can handle many low-speed digital and mixed-signal interface rates, while the 1.0 mA operating current benefits compact equipment. Use it for impedance isolation, level conditioning, or gain shaping rather than as a high-speed differential transceiver. Keep the signal path short, provide a continuous return plane, and avoid routing near switching nodes. For high-impedance sources, account for bias current and input capacitance when choosing source and feedback resistors.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MCP6021-E/MS — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MCP6021-I/MS | MCP6021T-E/MS |
|---|---|---|---|
| Package | MSOP-8 | MSOP-8 | MSOP-8 |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Amplifier Configuration | Single amplifier | Single amplifier | Single amplifier |
| Gain-Bandwidth Product | 10 MHz | 10 MHz | 10 MHz |
| Typical Operating Current | 1.0 mA | 1.0 mA | 1.0 mA |
| Typical Input Offset Voltage | <0.5 mV | <0.5 mV | <0.5 mV |
| Supply Voltage Range | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V |
| Temperature Grade | Extended temperature | Industrial temperature | Extended temperature |
| Rail-to-Rail Input and Output | Yes | Yes | Yes |
Ключевые отличия
- Extended-temperature ordering option (против MCP6021-I/MS)
- Low operating current for a 10 MHz amplifier (против MCP6021T-E/MS)
- Low-voltage rail-to-rail signal conditioning (против MCP6021-I/MS)
Заметки по проектированию
Decouple the MCP6021-E/MS supply pins with a ceramic bypass capacitor placed close to V+ and the ground reference. Keep the connection from the capacitor's ground terminal to the V- pin short and use the same solid ground plane used by the analog signal path. Although the typical operating current is only 1.0 mA, supply-impedance and layout effects can move the supply node during fast transitions, adding noise to sensitive analog signals.
Route the non-inverting and inverting inputs as short, quiet traces and locate feedback resistors near the amplifier pins. Avoid routing these nets beneath or parallel to switching-converter power paths. For high-impedance sensors, minimize leakage through board contamination and guard the input node when appropriate. The MSOP-8 land pattern and pin numbering must follow the package drawing in the manufacturer datasheet.
Do not assume that rail-to-rail input and output operation guarantees exact output reach to the supply rails. Check the specified output swing, load current, input common-mode range, and gain in datasheet 20001685E before using the amplifier as a comparator or precision level shifter. Also verify capacitive-load stability with the intended feedback network, particularly when driving long PCB traces, cables, or sampling networks.
Информация о соответствии
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status is stated for this ordering code. The MCP6021 is a general-purpose amplifier and is not identified as an AEC-Q100-qualified automotive part.