Microchip Technology

MCP6021-E/MS - 10MHz RRO Op Amp | Microchip | MSOP-8

MPN: MCP6021-E/MS ✓ Active
<0.5 mV Vdss 1.0 mA Id 8-lead MSOP Package
MOQ: 1 |

MCP6021-E/MS Overview

Microchip Technology MCP6021-E/MS is a single, rail-to-rail input and output operational amplifier with a 10 MHz gain-bandwidth product, 1.0 mA typical operating current, and offset voltage below 0.5 mV, housed in an 8-lead MSOP package. Its 2.5 V to 5.5 V supply range supports low-voltage analog systems where the input and output signals must approach the available supply rails.

An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. The MCP6021 belongs to the broader hierarchy of operational amplifier, analog amplifier IC, and signal-conditioning semiconductor. Rail-to-rail inputs allow the amplifier to operate with input voltages near the lower and upper supply limits, while rail-to-rail outputs improve output swing. These characteristics make the device useful for sensors, portable instrumentation, audio signal paths, and low-voltage data-acquisition systems.

Key features include a 10 MHz gain-bandwidth product, typical operating current of 1.0 mA, and typical input offset voltage below 0.5 mV. The Microchip MCP6021 family also provides low bias current, high open-loop gain, and general-purpose operation across industrial and extended-temperature options. The MCP6021-E/MS suffix identifies the extended-temperature version in the 8-lead MSOP configuration, making it suitable for industrial equipment when the circuit operates within the manufacturer-specified temperature limits.

The 10 MHz bandwidth supports closed-loop gains and signal frequencies that would be difficult to handle with a slow precision amplifier. At the same time, the 1.0 mA typical operating current keeps the amplifier suitable for portable and embedded systems. Designers should account for amplifier stability, output drive, load impedance, input common-mode range, and rail-to-rail output behavior when selecting feedback and external compensation networks.

Typical uses include buffering sensor outputs, amplifying low-level analog signals, active filtering, portable test equipment, and audio or communications interface circuits. The low supply current benefits battery-operated equipment, while the 10 MHz bandwidth provides useful responsiveness for moderate-frequency signal conditioning.

PCB implementation requires careful decoupling and stable return paths. Place the power-supply bypass capacitor close to the positive supply and ground pins, route the input and output traces away from switching nodes, and use a solid ground plane. Check capacitive-load stability and output-swing limits against the actual load before committing to the design.

This page combines the manufacturer device information, MPN packaging details, comparison options, and practical implementation guidance to support component selection, PCB planning, and replacement evaluation.

Drop-in alternatives for MCP6021-E/MS — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

MCP6021-I/MS

✅ Drop-In
📦 MSOP-8
Industrial temperature grade versus the E/MS extended-temperature grade; gain-bandwidth product remains 10 MHz and typical operating current remains 1.0 mA.

📋 Reference alternative (not in catalog)

MCP6021T-E/MS

✅ Drop-In
📦 MSOP-8
T designates the tape-and-reel ordering form; core ratings remain 10 MHz gain-bandwidth product and 1.0 mA typical operating current.

📋 Reference alternative (not in catalog)

MCP6021-E/MS Maximum Ratings & Electrical Characteristics

Amplifier Type Single general-purpose operational amplifier
Gain-Bandwidth Product 10 MHz
Typical Operating Current 1.0 mA
Typical Input Offset Voltage <0.5 mV
Supply Voltage Range 2.5 V to 5.5 V
Package 8-lead MSOP
Package Width 3.00 mm
Mounting Type Surface mount

MCP6021-E/MS Pin Configuration

MSOP-8 Package Pinout Diagram MSOP-8 3x3mm, P0.65mm, JEDEC MO-187. 1 8 2 7 3 6 4 5 MSOP-8
Pin 1 NC — Not connected
Pin 2 IN- — Inverting input
Pin 3 IN+ — Non-inverting input
Pin 4 V- — Negative power supply
Pin 5 NC — Not connected
Pin 6 OUT — Analog output
Pin 7 V+ — Positive power supply
Pin 8 NC — Not connected

Typical Applications

MCP6021-E/MS is suitable for 6 applications: Battery-Powered Sensor Signal Conditioning, Industrial Instrumentation Buffer, Low-Voltage Audio Preamp, Active Analog Filter, Portable Medical Monitoring Front End, Communications Interface Buffer.

📱

Battery-Powered Sensor Signal Conditioning

The MCP6021-E/MS is suitable for conditioning sensor outputs in portable, battery-powered equipment because its typical operating current is 1.0 mA and its supply range begins at 2.5 V. Rail-to-rail input capability supports signals positioned near either supply rail, while the 10 MHz gain-bandwidth product provides useful response for moderate-frequency sensor dynamics. Place the amplifier between the sensor and an ADC or controller, use a low-noise bypass capacitor at the supply pins, and verify the actual input common-mode range, output swing, and capacitive-load stability for the selected operating point.

🏭

Industrial Instrumentation Buffer

The MCP6021-E/MS can buffer low-level instrumentation signals in industrial control systems where a 2.5 V to 5.5 V supply and extended-temperature ordering option are required. Its typical offset voltage below 0.5 mV limits input-referred error at low signal levels, and the 10 MHz gain-bandwidth product supports moderate-frequency process signals. Use the amplifier as a voltage follower or a low-gain stage, route the input directly to the non-inverting or inverting terminal, and return the feedback network over a quiet ground plane to reduce offset and noise pickup.

🎧

Low-Voltage Audio Preamp

The MCP6021-E/MS is appropriate for a low-voltage audio preamplifier when low supply current and moderate bandwidth are more important than high-voltage output capability. Its 10 MHz gain-bandwidth product provides ample response for audio-band amplification, and the 1.0 mA typical operating current supports portable audio hardware. Connect the input through a defined source resistance, select a feedback gain compatible with the device's stability characteristics, and check the output waveform at the maximum planned signal level. Headphone or speaker loads require separate drive circuitry because an operational amplifier is not a power-output stage.

🔧

Active Analog Filter

The MCP6021-E/MS is useful in an active filter built around a 2.5 V to 5.5 V analog rail because its 10 MHz gain-bandwidth product provides more open-loop bandwidth than many low-power precision amplifiers. It can implement first- and higher-order low-pass, high-pass, or band-pass networks when component tolerances and phase margin are considered carefully. Keep passive components close to the amplifier pins, use an established filter topology with supported noise-gain values, and simulate tolerance and load effects. The rail-to-rail output characteristic helps preserve dynamic range when the signal approaches the available output swing.

💊

Portable Medical Monitoring Front End

The MCP6021-E/MS can form the analog front end of a portable monitoring device when its extended-temperature ordering option, 1.0 mA typical current, and less than 0.5 mV typical offset voltage fit the signal chain. The amplifier can buffer a low-level sensor or condition a signal before digitization. Its 10 MHz bandwidth avoids limiting moderate-frequency physiological signals, although system noise, protection components, patient safety requirements, and electrode-source impedance determine the final suitability. Validate the complete analog path for offset, drift, noise, common-mode limits, and fault behavior before production use.

🌐

Communications Interface Buffer

The MCP6021-E/MS is suitable for low-voltage communications interface buffering when the signal remains within its specified input and output limits. The 10 MHz gain-bandwidth product can handle many low-speed digital and mixed-signal interface rates, while the 1.0 mA operating current benefits compact equipment. Use it for impedance isolation, level conditioning, or gain shaping rather than as a high-speed differential transceiver. Keep the signal path short, provide a continuous return plane, and avoid routing near switching nodes. For high-impedance sources, account for bias current and input capacitance when choosing source and feedback resistors.

Recommended Products Summary

MCP6021-I/MS Same-family MSOP amplifier for industrial-temperature sensor interfaces Used in: Battery-Powered Sensor Signal Conditioning, Industrial Instrumentation Buffer, Portable Medical Monitoring Front End MCP6022-I/MS Same-family dual amplifier for two-channel sensor conditioning Used in: Battery-Powered Sensor Signal Conditioning MCP6024-I/SL Microchip Technology Used in: Industrial Instrumentation Buffer MCP6022-E/MS Same-family dual amplifier for stereo preamplifier channels Used in: Low-Voltage Audio Preamp, Active Analog Filter, Portable Medical Monitoring Front End MCP6023-E/MS Same-family dual amplifier option Used in: Low-Voltage Audio Preamp, Communications Interface Buffer MCP6021T-E/MS Same-family MSOP amplifier in tape-and-reel ordering form Used in: Active Analog Filter, Communications Interface Buffer
What are the key specifications of MCP6021-E/MS that engineers should know?
The MCP6021-E/MS is a single rail-to-rail operational amplifier with a 10 MHz gain-bandwidth product, 1.0 mA typical operating current, less than 0.5 mV typical input offset voltage, and a 2.5 V to 5.5 V supply range. It is packaged in an 8-lead MSOP. According to the Microchip MCP6021/1R/2/3/4 datasheet 20001685E, the family also provides low bias current and high open-loop gain, making it appropriate for general-purpose low-voltage signal conditioning.
Where can I download the MCP6021 datasheet PDF?
The manufacturer datasheet is available directly from Microchip at the official PDF URL for document 20001685E. It covers the MCP6021/1R/2/3/4 rail-to-rail input and output amplifier family, including the MCP6021 extended-temperature 8-lead MSOP configuration. Use the manufacturer PDF for the complete electrical-characteristics table, pin description, typical application circuits, ordering information, and package drawings rather than relying on a distributor summary.
Where can I find the MCP6021-E/MS pinout?
The MCP6021-E/MS pinout is documented in the pin-description section of the Microchip MCP6021/1R/2/3/4 datasheet 20001685E. The device uses an 8-lead MSOP package, designated MSOP-8 in the package library. Assign PCB nets using the manufacturer's numbered pin table and preserve the exposed package geometry and land pattern specified for the MSOP outline.
What is the operating voltage of MCP6021-E/MS?
The MCP6021-E/MS operates from a 2.5 V to 5.5 V power-supply range. According to the Microchip MCP6021/1R/2/3/4 datasheet 20001685E, this range applies to the amplifier family and supports operation from a single 3.3 V or 5 V rail when the surrounding circuit uses compatible logic levels. Input and output limits must remain within the device's specified common-mode and swing ranges.
What is the gain-bandwidth product of MCP6021-E/MS?
The MCP6021-E/MS has a gain-bandwidth product of 10 MHz. This value establishes its nominal small-signal bandwidth for a given closed-loop gain and makes it suitable for moderate-frequency amplification, buffering, and filtering. According to the Microchip MCP6021 product information and datasheet 20001685E, the amplifier also has low bias current, high open-loop gain, and rail-to-rail input and output characteristics.
Is MCP6021-E/MS suitable for battery-powered sensor circuits?
Yes, the MCP6021-E/MS is well suited to battery-powered sensor interfaces because its typical operating current is 1.0 mA and its supply range starts at 2.5 V. The rail-to-rail input characteristic is valuable when conditioning sensor outputs near the supply rails, while the 10 MHz gain-bandwidth product provides more bandwidth than a basic precision amplifier. Designers must still account for total system load, regulator efficiency, and amplifier output-swing limits.
Where can I buy MCP6021-E/MS and what is its current price?
Use the Request a Quote form on this page to request MCP6021-E/MS pricing, availability, and a quotation for the exact 8-lead MSOP MPN. The form allows procurement teams to confirm current commercial terms without relying on a static page value. Lead time, minimum order quantity, and stock status should be confirmed with the XAIPART sales team when the quotation is returned.
Is MCP6021-E/MS in stock and what is the lead time?
Current MCP6021-E/MS stock and lead time should be confirmed through the Request a Quote form on this page. The exact MPN is identified as an 8-lead MSOP single amplifier, which helps the sales team match the correct manufacturer ordering code and package. If production planning requires a committed date, request that confirmation before releasing the component into the bill of materials.
How long does it take to obtain a quotation for MCP6021-E/MS?
The quotation response time for MCP6021-E/MS is established when the request is submitted through the Request a Quote form on this page. Include the required quantity, target date, and any reel or moisture-packaging requirements with the request. The exact MPN, MCP6021-E/MS, corresponds to the single extended-temperature amplifier in an 8-lead MSOP package.
What can replace MCP6021-E/MS?
The closest same-package replacements identified for MCP6021-E/MS are MCP6021-I/MS and MCP6021T-E/MS, both using the 8-lead MSOP configuration and retaining the MCP6021 family's 10 MHz gain-bandwidth product and 1.0 mA typical operating current. MCP6021-I/MS changes the temperature grade, while MCP6021T-E/MS changes the tape-and-reel ordering form. Verify the complete ordering code and temperature requirements before substitution.
Is MCP6021-I/MS the same as MCP6021-E/MS?
No, MCP6021-I/MS and MCP6021-E/MS share the same 8-lead MSOP package and core amplifier ratings, but their temperature grades differ. The E/MS variant is the extended-temperature MCP6021 configuration, whereas I/MS denotes the industrial-temperature option. Both are identified as single 10 MHz rail-to-rail amplifiers with approximately 1.0 mA typical operating current, so selection depends primarily on the required environmental range.
When should I choose MCP6021-E/MS over MCP6021-I/MS?
Choose MCP6021-E/MS when the circuit requires Microchip's extended-temperature MCP6021 option, while MCP6021-I/MS is preferable when the industrial-temperature grade is sufficient. Both use the 8-lead MSOP package and share the family-level 10 MHz gain-bandwidth and 1.0 mA operating-current characteristics. Confirm the exact minimum and maximum junction or ambient operating temperatures against the manufacturer datasheet 20001685E for the selected ordering code.
Is MCP6021-E/MS suitable for industrial control and instrumentation?
The MCP6021-E/MS is suitable for industrial signal-conditioning applications that require an extended-temperature ordering option and operate from a 2.5 V to 5.5 V supply. Its 10 MHz bandwidth, rail-to-rail input and output behavior, less than 0.5 mV typical offset voltage, and 1.0 mA typical current are useful for sensor buffers and low-level analog conditioning. Final suitability depends on enclosure temperature, noise requirements, and grounding quality.
MCP6021-E/MS vs MCP6021T-E/MS — which drop-in option should be used?
Both MCP6021-E/MS and MCP6021T-E/MS are 8-lead MSOP versions of the extended-temperature MCP6021 amplifier with the same stated 10 MHz gain-bandwidth product and 1.0 mA typical operating current. The principal ordering difference is the T designation associated with the tape-and-reel form. For an existing MSOP PCB, either can fit electrically, but the exact manufacturer ordering code must match the required assembly and shipping format.
What is the best cross-brand equivalent for MCP6021-E/MS?
No verified cross-brand, pin-compatible 8-lead MSOP equivalent is identified for the MCP6021-E/MS. The available cross-reference information confirms the original Microchip part and related MCP6021 package variants but does not establish that another manufacturer's amplifier has the same pinout, electrical limits, and stability behavior. Do not substitute an amplifier solely by bandwidth and supply range; request a manufacturer cross-reference and verify every pin, common-mode limit, output swing, and load condition.

Engineering reference data for MCP6021-E/MS — comparison, design guidance, and compliance information.

Selection Guide

Choose MCP6021-E/MS for low-voltage analog designs that need the extended-temperature MCP6021 ordering option, particularly when combining rail-to-rail input and output behavior with a 10 MHz gain-bandwidth product and 1.0 mA typical operating current. MCP6021-I/MS is the same-package alternative when the industrial-temperature grade is sufficient, while MCP6021T-E/MS serves assemblies requiring the T tape-and-reel ordering form. The 2.5 V to 5.5 V supply range makes all three appropriate for 3.3 V and 5 V analog systems, but the selected amplifier must still satisfy the required input common-mode range, output swing, offset, bias current, load, and stability conditions. No verified cross-brand drop-in equivalent is available for this exact MSOP-8 MPN, so a functional substitute should not be approved without a complete pinout and electrical-characteristics review.

Comparison with Alternatives

Parameter This Product MCP6021-I/MS MCP6021T-E/MS
Package MSOP-8 MSOP-8 MSOP-8
Brand Microchip Technology Microchip Technology Microchip Technology
Amplifier Configuration Single amplifier Single amplifier Single amplifier
Gain-Bandwidth Product 10 MHz 10 MHz 10 MHz
Typical Operating Current 1.0 mA 1.0 mA 1.0 mA
Typical Input Offset Voltage <0.5 mV <0.5 mV <0.5 mV
Supply Voltage Range 2.5 V to 5.5 V 2.5 V to 5.5 V 2.5 V to 5.5 V
Temperature Grade Extended temperature Industrial temperature Extended temperature
Rail-to-Rail Input and Output Yes Yes Yes

Key Differentiators

  • Extended-temperature ordering option (vs MCP6021-I/MS)
  • Low operating current for a 10 MHz amplifier (vs MCP6021T-E/MS)
  • Low-voltage rail-to-rail signal conditioning (vs MCP6021-I/MS)

Design Notes

Decouple the MCP6021-E/MS supply pins with a ceramic bypass capacitor placed close to V+ and the ground reference. Keep the connection from the capacitor's ground terminal to the V- pin short and use the same solid ground plane used by the analog signal path. Although the typical operating current is only 1.0 mA, supply-impedance and layout effects can move the supply node during fast transitions, adding noise to sensitive analog signals.

Route the non-inverting and inverting inputs as short, quiet traces and locate feedback resistors near the amplifier pins. Avoid routing these nets beneath or parallel to switching-converter power paths. For high-impedance sensors, minimize leakage through board contamination and guard the input node when appropriate. The MSOP-8 land pattern and pin numbering must follow the package drawing in the manufacturer datasheet.

Do not assume that rail-to-rail input and output operation guarantees exact output reach to the supply rails. Check the specified output swing, load current, input common-mode range, and gain in datasheet 20001685E before using the amplifier as a comparator or precision level shifter. Also verify capacitive-load stability with the intended feedback network, particularly when driving long PCB traces, cables, or sampling networks.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status is stated for this ordering code. The MCP6021 is a general-purpose amplifier and is not identified as an AEC-Q100-qualified automotive part.

Related Searches

mcp6021 datasheet mcp6021 datasheet pdf mcp6021 price mcp6021 op amp mcp6021 equivalent MCP6021-E/MS datasheet MCP6021-E/MS pinout MCP6021-E/MS replacement MCP6021-E/MS equivalent MCP6021-E/MS MSOP-8 MCP6021-E/MS price Microchip MCP6021 op amp

Related Components & Terms

Microchip Technology MCP6021-E/MS MCP6021 MCP6021-I/MS MCP6021T-E/MS MCP6022 MCP6023 MCP6024 operational amplifier rail-to-rail input amplifier rail-to-rail output amplifier analog amplifier IC signal-conditioning semiconductor gain-bandwidth product input offset voltage input bias current open-loop gain MSOP-8 MSOP package family surface-mount package low-voltage analog circuit sensor interface battery-powered equipment active filter 2.5 V to 5.5 V power supply
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details