MCP6044-I/ST - Quad 1.4V RRIO Op Amp | Microchip Technology
Артикул: MCP6044-I/ST ✓ АктивенMCP6044-I/ST Обзор
An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, filter, buffer, or compare low-level analog signals. The MCP6044 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its rail-to-rail input and output capability allows signals to approach both supply rails, making it useful when available voltage headroom is limited by battery-powered or low-voltage systems.
Key specifications include a 1.4 V to 5.5 V operating supply, four amplifier channels, approximately 170 nV/√Hz input-voltage noise at 1 kHz, 100 pA typical input offset current, and 85 µV/°C input-offset voltage temperature coefficient. The device also provides 80 dB common-mode rejection and 600 nA typical quiescent current, supporting low-power operation when all four channels are active.
The MCP6044 uses built-in compensation to simplify amplifier design. Its approximately 3 V/µs slew rate allows the amplifier to respond to moderate-amplitude signal changes without requiring external compensation components. Rail-to-rail operation improves usable input and output range, while the low-noise and low-bias-current characteristics make the device suitable for precision sensor interfaces, current measurements, and buffered sensor chains.
Typical uses include portable sensor acquisition, battery-powered instrumentation, low-voltage audio signal conditioning, industrial monitoring, current sensing, and general-purpose analog buffers. The four integrated channels can support several small-signal stages in one package, reducing board area compared with four separate single or dual amplifier packages.
Designers should verify input common-mode voltage, output swing, load capacitance, and stability using the manufacturer operating conditions. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be configured according to the datasheet to avoid floating-node noise and unintended current consumption.
This page combines package, electrical, environmental, application, replacement, and design guidance for engineers evaluating the MCP6044-I/ST. It also distinguishes verified same-footprint options from changes that would require PCB redesign, supporting faster component selection without treating merely similar amplifiers as drop-in replacements.
Аналоги без доработки для MCP6044-I/ST — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MCP6044-I/ST (тот же форм-фактор и посадочное место) — отличается по Input Offset Voltage, Number of Amplifiers, Package.
MCP6044T-I/ST
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCP6044-E/ST
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →MCP6044-I/ST Максимальные параметры и электрические характеристики
| Number of Amplifiers | 4 channels |
| Рабочее напряжение питания | 1.4 V to 5.5 V |
| Absolute Maximum Supply Voltage | 6 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Gain-Bandwidth Product | 14 kHz |
| Slew Rate | 3 V/µs |
| Input Voltage Noise Density | 170 nV/√Hz at 1 kHz |
| Input Offset Current | 1 pA |
| Input Offset Voltage | 3 mV |
| Ток покоя | 600 nA |
| Common-Mode Rejection Ratio | 80 dB |
| Input Offset Voltage Temperature Coefficient | 85 µV/°C |
| Диапазон рабочих температур | -40°C to +85°C |
| Корпус | 14-pin TSSOP |
| Compensation | Built-in |
| Статус RoHS | Compliant |
Конфигурация выводов MCP6044-I/ST
| Контакт 1 | OUTA — Amplifier A output |
| Контакт 2 | -INA — Amplifier A inverting input |
| Контакт 3 | +INA — Amplifier A non-inverting input |
| Контакт 4 | V- — Negative supply connection |
| Контакт 5 | +INB — Amplifier B non-inverting input |
| Контакт 6 | -INB — Amplifier B inverting input |
| Контакт 7 | OUTB — Amplifier B output |
| Контакт 8 | OUTC — Amplifier C output |
| Контакт 9 | -INC — Amplifier C inverting input |
| Контакт 10 | +INC — Amplifier C non-inverting input |
| Контакт 11 | V+ — Positive supply connection |
| Контакт 12 | +IND — Amplifier D non-inverting input |
| Контакт 13 | -IND — Amplifier D inverting input |
| Контакт 14 | OUTD — Amplifier D output |
Типичное применение
MCP6044-I/ST подходит для 6 применениеs: Battery-Powered Sensor Acquisition, Industrial Process Monitoring, Low-Voltage Current Sensing, Portable Audio Signal Conditioning, Data Acquisition Front End, Low-Voltage Buffering.
Battery-Powered Sensor Acquisition
The MCP6044-I/ST fits low-voltage sensor acquisition because it operates from 1.4 V to 5.5 V, supports rail-to-rail inputs and outputs, and has 600 nA typical quiescent current. Four channels can amplify, filter, or buffer outputs from resistive, capacitive, or current-output sensors without requiring four separate packages. Its approximately 170 nV/√Hz input-noise density and 1 pA input-bias current help preserve small sensor signals. The main design limitation is the 14 kHz gain-bandwidth product, which suits slow measurements rather than fast waveform acquisition.
Рекомендуется
Industrial Process Monitoring
The MCP6044-I/ST can condition multiple low-level industrial signals from pressure, temperature, and level sensors while operating from a single 3.3 V or 5 V rail. Its rail-to-rail input range accommodates sensor outputs near either supply rail, and the 80 dB common-mode rejection ratio helps reject common-mode voltage present on long sensor wiring. Four integrated channels reduce board area, although system designers should consider shielding, filtering, and grounding for sensitive industrial measurements.
Рекомендуется
Low-Voltage Current Sensing
The MCP6044-I/ST is suitable for amplifying small voltage drops produced by current-sensing resistors in low-voltage power systems. The rail-to-rail input and output capability maximizes usable range when the shunt signal is close to ground or the positive rail. Its low input-bias current of approximately 1 pA minimizes measurement disturbance, while 600 nA typical quiescent current helps conserve power. The 3 mV input-offset specification must be included in the accuracy budget for low-current measurements.
Рекомендуется
Portable Audio Signal Conditioning
The MCP6044-I/ST can provide gain and buffering for low-level audio or microphone signals in portable equipment powered from a low-voltage battery. Rail-to-rail operation preserves more of the available signal range, and approximately 170 nV/√Hz input noise supports quiet amplification of weak sources. Its 3 V/µs slew rate is adequate for many speech and general audio signals but may limit high-fidelity or large-signal designs. Decoupling and input-biasing resistors should follow the manufacturer's typical application circuit.
Рекомендуется
Data Acquisition Front End
The MCP6044-I/ST provides four buffered analog channels for multiplexed or parallel low-frequency data-acquisition systems. Rail-to-rail inputs make it easier to use the full range of a 2.5 V, 3.3 V, or 5 V analog supply, while the low quiescent current limits overhead when the acquisition system operates continuously. The 14 kHz bandwidth is appropriate for temperature, pressure, position, and other slow-varying measurements. For faster transients, a higher-bandwidth amplifier is required.
Рекомендуется
Low-Voltage Buffering
The MCP6044-I/ST can buffer high-impedance sources or distribute a measured signal to downstream circuitry across four independent amplifier channels. Voltage-follower or moderate-gain configurations benefit from rail-to-rail output capability, while approximately 1 pA input-bias current reduces loading on sensitive sources. The 600 nA quiescent current is attractive for always-on systems. Designers should still verify capacitive-load stability and ensure each unused input is tied to a defined common-mode voltage.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MCP6044-I/ST — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MCP6044T-I/ST | MCP6044-E/ST |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP |
| Number of Amplifiers | 4 channels | 4 channels | 4 channels |
Ключевые отличия
- Four low-power amplifiers in one compact TSSOP (против MCP6044T-I/ST)
- Low-voltage rail-to-rail signal operation (против MCP6044-E/ST)
- Low quiescent demand for always-on analog systems (против MCP6044T-I/ST)
Заметки по проектированию
Place the supply-decoupling capacitor immediately between the V+ and V- pins, and route each amplifier's feedback and input components to minimize loop area. Because the MCP6044-I/ST is intended for low-noise and low-power analog systems, keep digital switching paths and high-current return currents away from the amplifier inputs. Use a continuous ground reference under the TSSOP where board layout permits.
Do not treat the rail-to-rail output as an ideal zero-volt swing. Verify output voltage and headroom against the load current and operating supply using the family datasheet. Similarly, unused amplifier inputs must be connected to a valid common-mode voltage, commonly ground, so that input bias current does not create an uncontrolled operating point.
The approximately 170 nV/√Hz input-noise density is appropriate for many slow sensor and audio signals, but the 14 kHz gain-bandwidth product limits usable closed-loop bandwidth. Use modest signal amplitudes and verify capacitive-load stability before driving long cables or large loads. For high-frequency, high-amplitude, or precision demanding signals, select an amplifier with lower noise, greater bandwidth, and tighter offset specifications.
Информация о соответствии
The product listing identifies the MCP6044-I/ST as RoHS compliant. Automotive qualification is not identified for this ordering code.