MSP430F6721IPN - 25MHz Mixed-Signal MCU | Texas Instruments
Артикул: MSP430F6721IPN ✓ АктивенMSP430F6721IPN Обзор
A mixed-signal microcontroller is a semiconductor that combines digital control logic with analog measurement functions. The MSP430F6721 belongs to the hierarchy of mixed-signal MCU, 16-bit RISC microcontroller, embedded controller, and metering SoC. Its Sigma-Delta ADC architecture is intended for extracting useful measurements from slowly changing or heavily quantized analog signals while keeping the external signal chain manageable.
Key features include 32 KB of Flash memory, 2 KB of SRAM, a 25 MHz CPU, two integrated Sigma-Delta ADCs, an LCD interface, and a real-time clock. The 80-pin LQFP package provides enough connection capacity for sensor inputs, LCD signals, communications, and metering-system control functions. A 3.6 V low-supply-voltage design supports low-power embedded metering applications.
The MSP430 CPU architecture uses a 16-bit RISC instruction set with 16-bit registers and constant generators. Its low-power operating modes are relevant to utility meters and other systems that spend substantial time measuring or waiting between communication intervals. Flash execution, RAM organization, clock behavior, and converter performance should be checked against the operating conditions of the final meter design.
Typical uses include single-phase electricity meters, smart energy meters, industrial energy monitors, load-management equipment, and LCD-based metering terminals. The integrated converters suit measurement channels, the real-time clock supports time-based metering functions, and the LCD interface simplifies the connection to a local display.
When designing the PCB, reserve clean grounding and short analog paths around the Sigma-Delta ADC inputs, and follow the manufacturer pin-description and layout guidance. Verify ADC source impedance, input filtering, LCD timing, reset behavior, clock configuration, and programming interfaces before releasing the layout.
This page combines the exact ordering information, package characteristics, pin-compatible family alternatives, comparison parameters, and implementation guidance needed to evaluate MSP430F6721IPN for a new metering design.
Аналоги без доработки для MSP430F6721IPN — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MSP430F6721IPN (тот же форм-фактор и посадочное место) — отличается по ADC Architecture, Active-Mode Current, Package, Product Type, Real-Time Clock.
MSP430F6726IPZR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MSP430F6721IPZR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MSP430F6723IPZ
✅ Прямая заменаУточнить цену
Открыть даташит →MSP430F6730IPN
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MSP430F6736IPNR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MSP430F6721IPN Максимальные параметры и электрические характеристики
| Product Type | Single-phase metering system-on-chip |
| CPU Architecture | 16-bit MSP430 RISC |
| Maximum Clock Speed | 25 MHz |
| Flash Memory | 32 KB |
| RAM Memory | 2 KB |
| ADC Architecture | 2 Sigma-Delta ADCs |
| ADC Resolution | 10-bit and 24-bit |
| Real-Time Clock | Integrated |
| LCD Interface | Integrated |
| General-Purpose I/O | 52 pins |
| Напряжение питания | 3.6 V low-supply-voltage range |
| Active-Mode Current | 265 uA/MHz typical at 8 MHz and 3.0 V |
| Корпус | 80-pin LQFP (PN), 12 x 12 mm |
| Тип монтажа | Surface mount |
| Диапазон рабочих температур | -40°C to +85°C |
| Internal Oscillator | Internal |
Руководство по цоколевке MSP430F6721IPN в корпусе 80-pin lqfp (pn), 12 x 12 mm
Цоколевка для MSP430F6721IPN (корпус 80-pin lqfp (pn), 12 x 12 mm). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для MSP430F6721IPN.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MSP430F6721IPN подходит для 6 применениеs: Single-Phase Smart Electricity Meters, Industrial Energy Monitoring Terminals, LCD-Based Utility Meter Interfaces, Load Management and Energy-Control Equipment, Low-Power Sensor and Acquisition Nodes, Compact Residential Metering Controllers.
Single-Phase Smart Electricity Meters
The MSP430F6721IPN fits a single-phase smart electricity meter because it combines a 16-bit, 25 MHz MSP430 CPU with two Sigma-Delta ADCs, 32 KB of Flash, and 2 KB of RAM. The converters can support energy-current measurement channels, while the integrated real-time clock supports time-based measurement records. Its LCD interface provides a local display path without requiring a separate display controller. The principal design trade-off is the limited 2 KB of RAM, so acquisition buffering and communication code must be sized carefully around the complete firmware architecture.
Рекомендуется
Industrial Energy Monitoring Terminals
For industrial energy monitoring, the MSP430F6721IPN provides a compact mixed-signal control platform with two Sigma-Delta ADCs and 52 general-purpose I/O pins. The 32 KB of Flash accommodates a meter-oriented firmware image, while 2 KB of RAM can support sampled values, display buffers, and protocol state. Its stated active-mode current of 265 uA/MHz at 8 MHz and 3.0 V provides a useful baseline for a low-power design, although local display consumption, communications, and sensor excitation must be included in the final power budget.
Рекомендуется
LCD-Based Utility Meter Interfaces
The MSP430F6721IPN is well suited to an LCD-based utility meter interface because the LCD interface and real-time clock are integrated with the metering MCU. Designers can use one 16-bit controller for acquisition, timekeeping, display updates, and local keypad or communication control rather than splitting those functions across separate devices. The 80-pin LQFP also exposes 52 general-purpose I/O pins, but engineers should allocate those pins according to the exact LCD segment mapping and alternative peripheral functions in the manufacturer pin table.
Рекомендуется
Load Management and Energy-Control Equipment
The MSP430F6721IPN can act as the measurement and control core in load-management equipment by combining Sigma-Delta conversion, 16-bit computation, and multiple I/O capabilities in one package. The 25 MHz CPU supports responsive control logic, and the two integrated ADCs can support voltage or current-related measurement channels when paired with suitable external circuitry. Its low-power architecture is advantageous in equipment expected to operate continuously, while the limited memory resources make careful partitioning of acquisition, communications, and control routines important.
Рекомендуется
Low-Power Sensor and Acquisition Nodes
The MSP430F6721IPN can serve as the acquisition and control node in a low-power sensing installation where analog measurement and a local display are required. Its two Sigma-Delta ADCs are suited to metering-style measurements, and the real-time clock can timestamp events without an external timekeeping component. The 52 I/O pins provide flexible connections to sensors, communication hardware, and displays. Design effort should focus on input impedance, filtering, reference stability, and ensuring that the selected ADC channel has the required resolution for the intended measurement.
Рекомендуется
Compact Residential Metering Controllers
A compact residential metering controller benefits from the combination of 32 KB Flash, 2 KB RAM, two Sigma-Delta ADCs, LCD support, and a real-time clock in the MSP430F6721IPN. This integration can reduce the number of discrete components needed for a compact wall-mounted or panel-mounted meter. The 80-pin LQFP footprint requires careful escape routing around the analog inputs and LCD interface, while the 25 MHz CPU clock should be selected according to communication timing, power-consumption targets, and the required acquisition update rate.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MSP430F6721IPN — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MSP430F6726IPZR | MSP430F6721IPZR | MSP430F6723IPZ | MSP430F6730IPN | MSP430F6736IPNR |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 80-pin LQFP (PN), 12 x 12 mm | 80-pin LQFP | 80-pin LQFP | 80-pin LQFP | 80-pin LQFP | 80-pin LQFP |
| Pin Count | 80 pins | 80 pins | 80 pins | 80 pins | 80 pins | 80 pins |
| CPU Architecture | 16-bit MSP430 RISC | 16-bit MSP430 RISC | 16-bit MSP430 RISC | 16-bit MSP430 RISC | 16-bit MSP430 RISC | 16-bit MSP430 RISC |
Ключевые отличия
- Purpose-built metering integration (против MSP430F6730IPN)
- Defined memory and speed configuration (против MSP430F6726IPZR)
- Original device identity for approved designs (против MSP430F6736IPNR)
Заметки по проектированию
Assign the ADC inputs using the exact manufacturer pin-description table and keep the analog traces short, away from LCD drive lines and switching-supply nodes. Place filtering and input-protection components close to the associated pins, and provide a quiet return path for the analog reference. Because the device combines metering conversion with LCD and communications peripherals, validate the complete ground and reference arrangement on a prototype rather than relying only on nominal pin placement.
Build the power budget from the stated 265 uA/MHz typical active-mode figure at 8 MHz and 3.0 V, then add LCD, ADC, communications, and external-interface loads. Account for the operating state of every peripheral between measurements. The integrated low-power features are valuable in metering equipment, but a practical energy budget requires the actual clock frequency, supply voltage, duty cycle, and peripheral activity rather than the active-mode figure alone.
Do not treat an 80-pin package match as proof of functional interchangeability. Before replacing MSP430F6721IPN with an MSP430F67xx candidate, compare ADC channel assignment and resolution, Flash and RAM requirements, LCD mapping, real-time-clock behavior, pin multiplexing, clock configuration, and startup dependencies. Compile the existing firmware against the candidate device definition and perform a hardware regression test across reset, measurement, display, and communications states.
Plan firmware and memory use around the device’s 2 KB of RAM. Avoid placing large display, communications, and acquisition buffers in RAM unless the complete memory map has been calculated. Keep time-critical acquisition routines deterministic, minimize interrupt latency, and confirm that the clock divider and low-power settings match the metering update interval. Program-memory utilization should be checked early because added communications or display functions can change the 32 KB Flash budget significantly.
Информация о соответствии
The ordering information identifies an industrial-temperature MSP430F6721IPN but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because this ordering code is not identified as an automotive-qualified variant.