Texas Instruments

OPA130PA - 1MHz Low-Power FET-Input Op Amp | Texas Instruments

Артикул: OPA130PA ✓ Активен
1 mV maximum Vdss 20 pA maximum Id 8-pin PDIP, 0.300 inch body width Package
MOQ: 1 |

OPA130PA Обзор

The Texas Instruments OPA130PA is a single, low-power, precision FET-input operational amplifier with a 1 MHz gain-bandwidth product, 20 pA maximum input bias current, and 530 uA typical quiescent current. It operates from 4.5 V to 36 V total supply voltage, including ±18 V dual-supply operation, and is supplied in an 8-pin PDIP package for through-hole and legacy industrial designs.

A FET-input operational amplifier is an op amp whose input stage uses field-effect transistors rather than bipolar input transistors. The OPA130PA combines the very high input impedance and low bias current of a FET input stage with the precision dc characteristics expected from the OPAx130 family. In signal-chain terms, the device belongs to the operational-amplifier family and ultimately to the broader analog integrated-circuit and semiconductor categories.

Key specifications include a maximum input offset voltage of 1 mV, minimum open-loop gain of 120 dB, minimum common-mode rejection of 90 dB, and a maximum input bias current of 20 pA. Its 1 MHz bandwidth makes it suitable for precision buffers, instrumentation, sensor interfaces, and moderate-frequency signal conditioning. The 530 uA quiescent current supports portable, battery-powered, and high-impedance instrumentation systems where amplifier power consumption is important.

The OPA130PA uses a precision internal design that supports low-offset operation and high open-loop gain. Its FET input stage is particularly valuable when the source impedance is high, because the amplifier draws minimal input current and therefore minimizes source-loading errors. The device is also suitable for transimpedance-style front ends where the signal source may be a sensor with picoamp-level leakage.

Typical uses include low-level sensor amplification, current measurement, bridge-amplifier interfaces, audio and communications buffers, laboratory instrumentation, and portable measurement equipment. The wide supply range supports both single-supply systems and traditional ±15 V laboratory rails. Because the OPA130PA is a general-purpose precision amplifier rather than a high-speed comparator or rail-to-rail device, applications requiring operation close to the supply rails or substantially higher bandwidth should use a different amplifier family.

For PCB design, treat the PDIP package as a through-hole component and provide adequate clearance around the leads. Decoupling capacitors should be placed close to the supply pins, and input and output routing should avoid proximity to switching nodes. Confirm the input common-mode range and output swing against the actual supply voltage before finalizing the bias point.

This page combines the manufacturer product information, distributor records, cross-reference results, application guidance, and design notes into one engineering-focused reference for sourcing and circuit implementation.

Аналоги без доработки для OPA130PA — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с OPA130PA (тот же форм-фактор и посадочное место) — отличается по Input Bias Current, Package, Amplifier Type, Open-Loop Gain, Quiescent Current.

Texas Instruments
Input Bias Current: 20 pA typical
Package: 8-pin SOIC (D), surface mount
Amplifier Type: Single, General Purpose, FET-Input Operational Amplifier
Сравнить с OPA130PA →
Texas Instruments
Input Bias Current: 50 pA
Package: 8-pin PDIP
Open-Loop Gain: 600
Сравнить с OPA130PA →
Texas Instruments
Input Bias Current: ±10 pA
Package: 8-pin PDIP
Amplifier Type: Single J-FET-input operational amplifier
Сравнить с OPA130PA →

OPA134PA

✅ Прямая замена
Texas Instruments
📦 8-pin PDIP
Single high-performance audio operational amplifier · 1 circuit · 8 MHz · 50 pA · 8 nV/√Hz · 0.00008% · 20 V/µs · 600

Уточнить цену

Открыть даташит →

OPA137PA

✅ Прямая замена
Texas Instruments
📦 8-pin PDIP
Single J-FET-input operational amplifier · 1 channel · 36 V · ±18 V · 1 MHz · 145 dB · ±10 pA · 120 µA per channel

Уточнить цену

Открыть даташит →

OPA130UA

✅ Прямая замена ⚠️ Характеристики не проверены
Texas Instruments
📦 8-pin PDIP
Single, General Purpose, FET-Input Operational Amplifier · 1 · 1 MHz · 2 V/us · 20 pA typical · 530 uA typical · +/-2.25 V to +/-18 V · 8-pin SOIC (D), surface mount

Уточнить цену

Открыть даташит →

OPA130PA Максимальные параметры и электрические характеристики

Amplifier Type Single operational amplifier
Input Topology FET input
Gain-Bandwidth Product 1 MHz
Input Bias Current 20 pA maximum
Ток покоя 530 uA typical per amplifier
Input Offset Voltage 1 mV maximum
Open-Loop Gain 120 dB minimum
Common-Mode Rejection Ratio 90 dB minimum
Supply Voltage Range 4.5 V to 36 V
Total Supply Voltage Range 4.5 V to 36 V
Dual-Supply Operating Range +/-18 V
Корпус 8-pin PDIP, 0.300 inch body width
Тип монтажа Through-hole
Количество выводов 8
Low Offset Voltage 1 mV maximum
High Open-Loop Gain 120 dB minimum
Excellent Bandwidth 1 MHz
Статус RoHS Compliant
AEC-Q100 Qualification Not applicable

Конфигурация выводов OPA130PA

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
Контакт 1 NC — Not connected
Контакт 2 IN- — Inverting input
Контакт 3 IN+ — Non-inverting input
Контакт 4 V- — Negative supply connection
Контакт 5 NC — Not connected
Контакт 6 OUT — Amplifier output
Контакт 7 V+ — Positive supply connection
Контакт 8 NC — Not connected

Типичное применение

OPA130PA подходит для 6 применениеs: High-Impedance Sensor Amplifier, Portable Battery-Powered Instrumentation, Transimpedance Front End, Precision Current Measurement, Laboratory Buffer and Active Probe, Audio and Communications Buffering.

🧩

High-Impedance Sensor Amplifier

The OPA130PA fits high-impedance sensor front ends because its FET input stage draws no more than 20 pA of input bias current. That low loading preserves the voltage generated by piezoelectric, electrochemical, or very-high-value resistive sources. With a 1 MHz gain-bandwidth product and 120 dB minimum open-loop gain, the amplifier can provide useful closed-loop gain while retaining low-offset behavior. Place the amplifier close to the sensor connection, keep input traces short, and shield them from switching nodes.

🔋

Portable Battery-Powered Instrumentation

The OPA130PA is suited to portable instruments because its typical quiescent current is only 530 uA per amplifier. Combined with a 4.5 V minimum total supply and 20 pA maximum input bias current, it supports low-power measurement channels with sensitive sources. The precision offset specification of 1 mV maximum helps preserve small-signal accuracy, while the 1 MHz bandwidth supports sensor signals below the amplifier's full capability. Calculate the complete system budget, including gain resistors and external filtering.

💡

Transimpedance Front End

The OPA130PA can serve as the transimpedance amplifier in optical, photodiode, or photocurrent measurement circuits because its maximum input bias current is 20 pA. The low bias current reduces error current relative to the measured photocurrent and minimizes voltage error across a high-value feedback resistor. Its 90 dB minimum common-mode rejection ratio also helps suppress supply-related disturbances. Use the manufacturer stability and compensation guidance when selecting the feedback resistor and stray-capacitance allowance.

🏭

Precision Current Measurement

OPA130PA is appropriate for amplifying the voltage produced by a current shunt or current-sense element in precision industrial control systems. Its 1 mV maximum input offset voltage limits the error added at the input, and the 120 dB minimum open-loop gain supports accurate closed-loop operation. The wide 4.5 V to 36 V supply range also permits ±15 V laboratory instrumentation. For best results, keep the shunt connection compact and evaluate the amplifier's offset and bias-current errors against the required measurement resolution.

🖥️

Laboratory Buffer and Active Probe

OPA130PA works well as a laboratory buffer or active probe driver when the source impedance is high and signal loading must remain small. The 20 pA maximum input bias current is more suitable for this role than the tens-of-nanoampere input currents common in bipolar-input op amps. A 1 MHz bandwidth supports moderate-frequency waveforms, and ±18 V dual-supply operation simplifies compatibility with legacy bench instruments. Use short, guarded input traces and verify the output swing before driving the intended load.

🌐

Audio and Communications Buffering

OPA130PA is suitable for low-level audio and communications signal buffering because it combines a 1 MHz gain-bandwidth product with low input bias current and low quiescent current. It can isolate a high-impedance source from a downstream load while maintaining acceptable signal integrity at moderate frequencies. The 36 V maximum total supply permits operation from common laboratory rails and higher industrial bias arrangements. Avoid using it for high-frequency video or RF stages because its 1 MHz bandwidth is the limiting parameter.

What is the operating voltage range of OPA130PA?
The OPA130PA operates from 4.5 V to 36 V total supply voltage. According to the Texas Instruments OPA130 product information, this supports single-supply systems as well as dual supplies up to ±18 V. The exact usable input common-mode range is narrower than the total supply range, so the amplifier bias point must be checked against the device data before use near a supply rail.
What are the key specifications of OPA130PA that engineers should know?
The OPA130PA is a single FET-input op amp with a 1 MHz gain-bandwidth product, 20 pA maximum input bias current, 530 uA typical quiescent current, 1 mV maximum input offset voltage, and 120 dB minimum open-loop gain. Texas Instruments describes the OPA130 family as precision, low-power devices intended for general-purpose, portable, battery-operated, and high-source-impedance applications.
Where can I download the OPA130PA datasheet PDF?
The manufacturer product page for the OPA130 family is the authoritative starting point for the OPA130PA datasheet and ordering information. Texas Instruments states that the OPA130, OPA2130, and OPA4130 versions have identical specifications for design flexibility. Use the manufacturer PDF rather than a distributor mirror to confirm pin assignments, recommended operating conditions, and electrical characteristics.
Where is the OPA130PA pinout located?
The OPA130PA pinout is shown in the pin-configuration section of the Texas Instruments OPA130 datasheet. It is an 8-pin PDIP package with the same standard single-amplifier arrangement used by the OPAx130 family. Confirm pin numbers directly from the manufacturer drawing before assigning PCB tracks, particularly for pins marked NC, which must remain unconnected.
Is the OPA130PA suitable for high-impedance sensor interfaces?
Yes, the OPA130PA is well suited to high-impedance sensor interfaces because its FET input stage provides a maximum input bias current of 20 pA. Low input current reduces loading of piezoelectric sensors, electrochemical sensors, and high-value source impedances. Its 1 mV maximum input offset and 90 dB minimum common-mode rejection ratio also support accurate low-level signal conditioning.
What is the best drop-in replacement for OPA130PA?
The closest same-family drop-in candidates are the Texas Instruments OPA134PA and OPA137PA in the same 8-pin PDIP format. Drop-in status must be confirmed for the exact operating conditions, including supply voltage, common-mode range, offset voltage, and stability. For the highest confidence, use the manufacturer cross-reference search and compare the complete electrical tables before substituting a part into production.
What can replace OPA130PA?
The OPA130PA can be replaced by a pin-compatible precision FET-input op amp in the same 8-pin PDIP footprint, provided that the critical ratings remain acceptable. Texas Instruments OPA134PA and OPA137PA are same-brand candidates, while the OPA130 cross-reference record identifies an Analog Devices pin-to-pin replacement. Confirm the specific Analog Devices MPN and full parameter comparison before using a cross-brand substitution.
Is OPA130PA the same as OPA134PA?
No, the OPA130PA and OPA134PA share the same family style of precision FET-input architecture and can be evaluated as pin-compatible candidates in an 8-pin PDIP package, but they are not electrically identical. The OPA134 family is normally associated with a different precision-performance profile. Compare offset, bias current, bandwidth, common-mode range, and stability requirements for the intended circuit.
OPA130PA vs OPA137PA - which is better for instrumentation?
The OPA130PA is the better match when low quiescent current and the OPAx130 family specification are the primary priorities, while the OPA137PA may be preferred when the alternative family's offset and precision characteristics better satisfy the design. Both are 1 MHz-class single FET-input amplifiers in 8-pin PDIP packages. The final choice depends on measured noise, offset drift, supply headroom, and stability.
When should I choose OPA130PA over a higher-bandwidth op amp?
Choose the OPA130PA when the signal path needs very low bias current, a 1 MHz bandwidth, low power consumption, and precision dc behavior rather than high-speed performance. Its 530 uA typical quiescent current and 20 pA maximum bias current are valuable in battery-powered equipment and high-impedance measurement circuits. Choose a faster amplifier when slew rate or closed-loop bandwidth is the limiting specification.
Is OPA130PA suitable for battery-powered measurement equipment?
Yes, the OPA130PA is suitable for portable and battery-operated measurement equipment because its typical quiescent current is only 530 uA per amplifier. The FET input stage also avoids the higher bias current typical of bipolar-input op amps. Power budget calculations should include the quiescent current multiplied by the supply voltage, plus load-dependent current and the current required by external gain and filter networks.
Does OPA130PA support rail-to-rail operation?
The OPA130PA is not identified as a rail-to-rail input or rail-to-rail output amplifier in the manufacturer family information. It supports a wide 4.5 V to 36 V supply range, but the signal swing and common-mode limits must remain inside the specified operating region. If the signal can approach either supply rail, select an amplifier explicitly designed for rail-to-rail input and output.
Where to buy OPA130PA online?
Use the Request a Quote form on this page to request OPA130PA pricing, stock confirmation, and lead time from XAIPART. The exact quantity break, current availability, and delivery schedule are confirmed during quotation. For engineering evaluation, the Texas Instruments product page remains the authoritative source for lifecycle, ordering codes, and device documentation.
What is the price of OPA130PA?
Current OPA130PA pricing is generated through the XAIPART Request a Quote form on this page and depends on quantity, sourcing condition, and confirmed availability. Use that form for a purchase-ready quotation rather than relying on a historical catalog amount. The listing also lets you request packaging information and an estimated lead time for the required quantity.
What is the lead time for OPA130PA?
The current lead time for OPA130PA is confirmed through the Request a Quote form on this page. Lead time depends on order quantity, package form, and current manufacturer and distributor allocation. Submit the required part number, quantity, and target shipment date with the request so the commercial team can provide an actionable schedule.

Справочные инженерные данные для OPA130PA — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the OPA130PA for precision low-level buffering or high-impedance sensing when 1 MHz bandwidth, a maximum input bias current of 20 pA, and a typical quiescent current of 530 uA are the main priorities. It is also appropriate for ±18 V laboratory and industrial instrumentation designs that require a single amplifier in an 8-pin PDIP package. Consider OPA134PA when lower-offset precision is more important than the OPA130 power and bias-current profile, and consider OPA137PA when its alternative precision specifications better match the signal chain. OPA130UA is the closest same-family ordering option when its package construction is acceptable. Do not choose this amplifier for rail-to-rail input, high-speed video, or RF applications. For every substitution, verify common-mode range, output swing, stability, offset drift, and the manufacturer's pin configuration before releasing production artwork.

Сравнение с аналогами

Параметр Этот товар OPA134PA OPA137PA OPA130UA
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP ordering variant
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Amplifier Configuration Single Single Single Single
Gain-Bandwidth Product 1 MHz 8 MHz 5.5 MHz 1 MHz
Input Bias Current 20 pA maximum 5 pA typical 100 pA typical 20 pA maximum
Input Offset Voltage 1 mV maximum 0.5 mV maximum 0.5 mV maximum 1 mV maximum
Supply Voltage Range 4.5 V to 36 V 2.5 V to 36 V 4.5 V to 36 V 4.5 V to 36 V

Ключевые отличия

  • Lower power consumption than the precision alternatives (против OPA137PA)
  • High input impedance for sensor interfaces (против OPA134PA)
  • Direct same-family ordering alternative (против OPA130UA)

Заметки по проектированию

Place supply-decoupling capacitors close to the V+ and V- pins and connect the amplifier ground reference to the quiet analog return path. Keep the inverting and non-inverting inputs short and separate from switching-node copper. Because the OPA130PA uses a PDIP package, provide adequate lead-bend clearance and avoid applying mechanical stress to the pins during socket soldering.

Do not assume the 4.5 V to 36 V supply rating permits operation arbitrarily close to a rail. Check the specified input common-mode range and output swing against the intended signal and load. Also account for offset voltage, bias-current error, and resistor thermal drift when specifying the smallest measurable input. A higher-bandwidth amplifier may be required if the signal contains substantial content above 1 MHz.

For high-impedance sources, minimize PCB leakage and contamination around the input nodes, keep the input path short, and use a protective guard structure where practical. The 20 pA maximum input bias current is low, but board contamination can still create a comparable leakage error. Confirm stability with the intended source impedance, feedback network, and load capacitance using the manufacturer guidance.

Информация о соответствии

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

A distributor product listing identifies the OPA130PA as RoHS compliant. No AEC-Q100 automotive qualification is listed for this general-purpose amplifier.

Похожие запросы

OPA130PA datasheet OPA130PA pinout OPA130PA datasheet pdf OPA130PA specifications OPA130PA equivalent OPA130PA replacement OPA130PA cross reference OPA130PA vs OPA134PA OPA130PA PDIP-8 OPA130PA high impedance amplifier OPA130PA price OPA130PA stock Texas Instruments OPA130PA OPA130PA 1 MHz FET input op amp OPA130PA instrumentation amplifier

Связанные компоненты & термины

Texas Instruments OPA130PA OPA130 OPA134PA OPA137PA OPA130UA operational amplifier precision op amp FET-input amplifier field-effect transistor input analog integrated circuit semiconductor 1 MHz gain-bandwidth product 20 pA input bias current 530 uA quiescent current 1 mV input offset voltage 120 dB open-loop gain 90 dB CMRR 4.5 V to 36 V supply 8-pin PDIP through-hole package instrumentation amplifier high-impedance sensor interface transimpedance amplifier battery-powered measurement
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ