OPA2336P - Dual MicroPower Rail-to-Rail Op Amp | Texas Instruments
Артикул: OPA2336P ✗ Снят с производстваOPA2336P Обзор
An operational amplifier is a voltage-gain element used to amplify the difference between two input voltages. The OPA2336 belongs to the microPower CMOS operational-amplifier family within the broader amplifier IC and signal-conditioning hierarchy. Its low quiescent current is especially relevant to battery-powered instrumentation because the amplifier continues to consume power even when its signal input is near zero. The rail-to-rail output allows the output voltage to approach the positive and negative supply limits under suitable load conditions, providing more usable output range from a limited supply voltage.
The OPA2336 family combines low power consumption with precision-oriented performance. A maximum offset voltage of 125 µV supports accurate amplification of small signals, while the 1 pA input bias current is useful with high-impedance sensors and bias networks. The 115 dB open-loop gain indicates strong amplification capability, and the dual configuration provides two independent amplifier channels in one package. Identical electrical specifications are identified for the single, dual, and quad family members, allowing the same general signal-chain approach to be used when the required channel count changes.
According to the manufacturer product information, the OPA2336 operates from 2.3 V to 5.5 V. The low-voltage operating range makes the amplifier appropriate for portable measurement systems, low-voltage sensor interfaces, battery-operated test equipment, and embedded instrumentation. The datasheet excerpt also describes operation with a negative supply, extending the common-mode capability below ground. This feature can simplify circuits that measure bipolar or unipolar sensor signals without adding a separate midrail reference.
Typical uses include low-level sensor conditioning, current-to-voltage conversion, audio and communication interface stages, general-purpose voltage amplification, and precision analog measurement. The 100 kHz gain-bandwidth product and 0.03 V/µs slew rate shown in the component listing suit low-frequency and modest-bandwidth signal paths rather than high-speed video, RF, or precision audio applications. The 8-pin DIP package is mechanically convenient for laboratory assembly, but modern production designs may favor a surface-mount equivalent when board area, assembly automation, or vibration resistance is important.
Designers should verify the exact pinout, common-mode range, output-load limitations, input protection behavior, and stability requirements in the manufacturer datasheet before finalizing a PCB. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must be biased so that the output remains in its linear operating region. Because the two channels share one package, independent noise and thermal conditions can affect them differently, particularly when one channel drives a low-impedance load while the other handles a high-impedance source.
This page combines the confirmed manufacturer specifications with package information, practical analog-design guidance, sourcing fields, and a technical comparison framework. It also identifies where circuit-specific data must be taken directly from the manufacturer datasheet, helping engineers evaluate the OPA2336P without confusing family-level features with package-specific limitations.
Аналоги без доработки для OPA2336P — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
OPA2336PA
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
OPA2336P Максимальные параметры и электрические характеристики
| Amplifier Type | Dual operational amplifier |
| Architecture | CMOS operational amplifier |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2.3 V to 5.5 V |
| Ток покоя | 20 µA per amplifier |
| Input Offset Voltage | 125 µV maximum |
| Input Bias Current | 1 pA |
| Open-Loop Gain | 115 dB |
| Gain-Bandwidth Product | 100 kHz |
| Slew Rate | 0.03 V/µs |
| Тип выхода | Rail-to-Rail |
| Supply Type | Single-supply |
| Корпус | 8-pin DIP |
| Диапазон рабочих температур | -55 °C to +125 °C |
| Статус RoHS | Compliant |
Руководство по цоколевке OPA2336P в корпусе 8-pin dip
Цоколевка для OPA2336P (корпус 8-pin dip). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для OPA2336P.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
OPA2336P подходит для 6 применениеs: Battery-Powered Sensor Conditioning, Portable Medical Instrument Signal Acquisition, Industrial Process Measurement, Low-Power Audio Interface, Data Acquisition and Instrumentation, IoT Edge Sensor Node.
Battery-Powered Sensor Conditioning
The OPA2336P fits low-voltage sensor interfaces because each amplifier consumes 20 µA of quiescent current while the device operates from 2.3 V to 5.5 V. Its 1 pA input bias current minimizes loading on high-impedance sensors, and the 125 µV maximum input offset voltage supports accurate conditioning of small signals. Place the amplifier close to the sensor connector, use a stable low-noise supply, and provide local bypass capacitance to prevent supply ripple from entering the measurement chain.
Рекомендуется
Portable Medical Instrument Signal Acquisition
The OPA2336P can condition low-level physiological or diagnostic signals where low power and accurate small-signal amplification are important. Its 1 pA input bias current reduces input loading, while 125 µV maximum offset voltage and 115 dB open-loop gain support high-gain stages. The 2.3 V minimum supply permits integration into compact battery-operated equipment. Medical designs still require suitable isolation, protection, leakage, noise, and regulatory validation beyond the basic amplifier specifications.
Рекомендуется
Industrial Process Measurement
The OPA2336P is suitable for low-frequency process measurements that require two buffered channels, such as pressure, temperature, or resistive bridge signals. The 100 kHz gain-bandwidth product supports stable amplification within its intended bandwidth, and the 0.03 V/µs slew rate provides adequate response for many slow sensor waveforms. Use the two channels for differential input conditioning or separate sensor paths, and verify grounding and isolation requirements in industrial environments.
Рекомендуется
Low-Power Audio Interface
The OPA2336P can serve as a low-power audio preamplifier or line-stage buffer when the signal bandwidth is modest and rail-to-rail output is valuable. Its dual-channel architecture supports left and right signal paths, while 20 µA quiescent current per amplifier helps preserve battery life. The 100 kHz gain-bandwidth product and 0.03 V/µs slew rate are better aligned with speech, control, and general low-frequency audio than high-fidelity wideband audio; verify output swing and distortion limits in the datasheet.
Рекомендуется
Data Acquisition and Instrumentation
The OPA2336P is appropriate for buffering ADC inputs, amplifying transducer outputs, and providing active filtering in compact instrumentation. Two channels can process simultaneous measurements without requiring separate packages, and the low 1 pA bias current is beneficial when driving high-impedance dividers or sensors. Its 2.3 V to 5.5 V supply range simplifies compatibility with low-voltage mixed-signal systems. Confirm settling behavior, output-capacitance limits, and noise characteristics for the selected gain and bandwidth.
Рекомендуется
IoT Edge Sensor Node
The OPA2336P suits IoT edge nodes that process low-frequency sensor data from a compact battery supply. Its 20 µA quiescent current per amplifier reduces standby demand, while the dual configuration can handle two sensor inputs or one signal plus an auxiliary channel. The rail-to-rail output helps use more of a restricted supply range. A practical design should include local decoupling, defined grounding, input overvoltage protection, and a power-gating arrangement if long-term battery life is critical.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для OPA2336P — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар |
|---|---|
| Package | 8-pin DIP |
| Brand | Texas Instruments |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2.3 V to 5.5 V |
| Quiescent Current | 20 µA per amplifier |
| Input Offset Voltage | 125 µV maximum |
| Input Bias Current | 1 pA |
| Open-Loop Gain | 115 dB |
| Gain-Bandwidth Product | 100 kHz |
| Slew Rate | 0.03 V/µs |
Ключевые отличия
- Exceptionally low quiescent current for a dual precision amplifier (против OPA4137P)
- Low-voltage operation with rail-to-rail output (против OPA137U)
- Precision input characteristics in a dual-channel package (против OPA4137P)
Заметки по проектированию
Place the supply bypass capacitor and any additional ceramic decoupling directly beside the OPA2336P power pins. Keep the input and output traces short, avoid routing them beside switching nodes or high-current return paths, and provide a low-impedance ground reference. Because this is a precision, low-current amplifier, PCB leakage and contamination can be more important than the nominal 1 pA bias-current specification in high-impedance layouts.
Do not treat rail-to-rail output as an unlimited output-current or load-capacitance capability. Confirm the output swing, output-current limits, and stable capacitive-load range in the manufacturer datasheet for the intended load. Also avoid leaving an unused amplifier input floating; follow the datasheet recommendation for biasing the unused channel so its output remains stable and does not interfere with the powered channel.
Estimated dual-channel quiescent power at a 3.3 V supply is 0.132 mW, calculated from 20 µA per amplifier, two amplifiers, and 3.3 V: 20 µA × 2 × 3.3 V = 132 µW. Actual supply current rises with output loading, switching activity, and the selected operating mode. Use this calculation only as a baseline and include regulator quiescent current, sensor current, and load demand in the complete battery-life budget.
Информация о соответствии
RoHS compliance is identified in a technical comparison record. The listed operating temperature range is -55 °C to +125 °C. No confirmed automotive qualification or detailed substance-compliance information was identified.