Texas Instruments

OPA2336P - Dual MicroPower Rail-to-Rail Op Amp | Texas Instruments

MPN: OPA2336P ✗ Son Kullanım Zamanı
2.3 V to 5.5 V Vdss 20 µA per amplifier Id 8-pin DIP Package
MOQ: 1 |

OPA2336P Genel Bakış

The Texas Instruments OPA2336P is a dual-channel, single-supply microPower CMOS operational amplifier with rail-to-rail output, a 20 µA typical quiescent current per amplifier, a maximum input offset voltage of 125 µV, a 1 pA input bias current, and a 115 dB open-loop gain. The device is offered in an 8-pin through-hole DIP package, making it suitable for prototypes, educational designs, and systems assembled with conventional radial or socketed DIP components.

An operational amplifier is a voltage-gain element used to amplify the difference between two input voltages. The OPA2336 belongs to the microPower CMOS operational-amplifier family within the broader amplifier IC and signal-conditioning hierarchy. Its low quiescent current is especially relevant to battery-powered instrumentation because the amplifier continues to consume power even when its signal input is near zero. The rail-to-rail output allows the output voltage to approach the positive and negative supply limits under suitable load conditions, providing more usable output range from a limited supply voltage.

The OPA2336 family combines low power consumption with precision-oriented performance. A maximum offset voltage of 125 µV supports accurate amplification of small signals, while the 1 pA input bias current is useful with high-impedance sensors and bias networks. The 115 dB open-loop gain indicates strong amplification capability, and the dual configuration provides two independent amplifier channels in one package. Identical electrical specifications are identified for the single, dual, and quad family members, allowing the same general signal-chain approach to be used when the required channel count changes.

According to the manufacturer product information, the OPA2336 operates from 2.3 V to 5.5 V. The low-voltage operating range makes the amplifier appropriate for portable measurement systems, low-voltage sensor interfaces, battery-operated test equipment, and embedded instrumentation. The datasheet excerpt also describes operation with a negative supply, extending the common-mode capability below ground. This feature can simplify circuits that measure bipolar or unipolar sensor signals without adding a separate midrail reference.

Typical uses include low-level sensor conditioning, current-to-voltage conversion, audio and communication interface stages, general-purpose voltage amplification, and precision analog measurement. The 100 kHz gain-bandwidth product and 0.03 V/µs slew rate shown in the component listing suit low-frequency and modest-bandwidth signal paths rather than high-speed video, RF, or precision audio applications. The 8-pin DIP package is mechanically convenient for laboratory assembly, but modern production designs may favor a surface-mount equivalent when board area, assembly automation, or vibration resistance is important.

Designers should verify the exact pinout, common-mode range, output-load limitations, input protection behavior, and stability requirements in the manufacturer datasheet before finalizing a PCB. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must be biased so that the output remains in its linear operating region. Because the two channels share one package, independent noise and thermal conditions can affect them differently, particularly when one channel drives a low-impedance load while the other handles a high-impedance source.

This page combines the confirmed manufacturer specifications with package information, practical analog-design guidance, sourcing fields, and a technical comparison framework. It also identifies where circuit-specific data must be taken directly from the manufacturer datasheet, helping engineers evaluate the OPA2336P without confusing family-level features with package-specific limitations.

Drop-in alternatifler için OPA2336P — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

OPA2336PA

✅ Yerleştirme
📦 8-pin PDIP
Same dual OPA2336 family and 8-pin PDIP package; ordering suffix differs by 0%, while environmental and marking details require confirmation from the ordering table.

📋 Katalogda Olmayan Referans Alternatifi

OPA2336P Maksimum Değerlendirmeler & Elektriksel Özellikler

Amplifier Type Dual operational amplifier
Architecture CMOS operational amplifier
Number of Channels 2 channels
Supply Voltage Range 2.3 V to 5.5 V
Durağan Akım 20 µA per amplifier
Input Offset Voltage 125 µV maximum
Input Bias Current 1 pA
Open-Loop Gain 115 dB
Gain-Bandwidth Product 100 kHz
Slew Rate 0.03 V/µs
Çıkış Türü Rail-to-Rail
Supply Type Single-supply
Paket 8-pin DIP
İşletim Sıcaklığı Aralığı -55 °C to +125 °C
RoHS Durumu Compliant

OPA2336P 8-pin dip Pin Yapısı Kılavuzu

OPA2336P (8-pin dip paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.

8-pin dip paket pin çizelgesi için OPA2336P

Ayrıntılı pin çıkış verisi mevcut değil: OPA2336P.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

OPA2336P için uygundur 6 uygulamas: Battery-Powered Sensor Conditioning, Portable Medical Instrument Signal Acquisition, Industrial Process Measurement, Low-Power Audio Interface, Data Acquisition and Instrumentation, IoT Edge Sensor Node.

🔋

Battery-Powered Sensor Conditioning

The OPA2336P fits low-voltage sensor interfaces because each amplifier consumes 20 µA of quiescent current while the device operates from 2.3 V to 5.5 V. Its 1 pA input bias current minimizes loading on high-impedance sensors, and the 125 µV maximum input offset voltage supports accurate conditioning of small signals. Place the amplifier close to the sensor connector, use a stable low-noise supply, and provide local bypass capacitance to prevent supply ripple from entering the measurement chain.

💊

Portable Medical Instrument Signal Acquisition

The OPA2336P can condition low-level physiological or diagnostic signals where low power and accurate small-signal amplification are important. Its 1 pA input bias current reduces input loading, while 125 µV maximum offset voltage and 115 dB open-loop gain support high-gain stages. The 2.3 V minimum supply permits integration into compact battery-operated equipment. Medical designs still require suitable isolation, protection, leakage, noise, and regulatory validation beyond the basic amplifier specifications.

🏭

Industrial Process Measurement

The OPA2336P is suitable for low-frequency process measurements that require two buffered channels, such as pressure, temperature, or resistive bridge signals. The 100 kHz gain-bandwidth product supports stable amplification within its intended bandwidth, and the 0.03 V/µs slew rate provides adequate response for many slow sensor waveforms. Use the two channels for differential input conditioning or separate sensor paths, and verify grounding and isolation requirements in industrial environments.

🎧

Low-Power Audio Interface

The OPA2336P can serve as a low-power audio preamplifier or line-stage buffer when the signal bandwidth is modest and rail-to-rail output is valuable. Its dual-channel architecture supports left and right signal paths, while 20 µA quiescent current per amplifier helps preserve battery life. The 100 kHz gain-bandwidth product and 0.03 V/µs slew rate are better aligned with speech, control, and general low-frequency audio than high-fidelity wideband audio; verify output swing and distortion limits in the datasheet.

📊

Data Acquisition and Instrumentation

The OPA2336P is appropriate for buffering ADC inputs, amplifying transducer outputs, and providing active filtering in compact instrumentation. Two channels can process simultaneous measurements without requiring separate packages, and the low 1 pA bias current is beneficial when driving high-impedance dividers or sensors. Its 2.3 V to 5.5 V supply range simplifies compatibility with low-voltage mixed-signal systems. Confirm settling behavior, output-capacitance limits, and noise characteristics for the selected gain and bandwidth.

🧩

IoT Edge Sensor Node

The OPA2336P suits IoT edge nodes that process low-frequency sensor data from a compact battery supply. Its 20 µA quiescent current per amplifier reduces standby demand, while the dual configuration can handle two sensor inputs or one signal plus an auxiliary channel. The rail-to-rail output helps use more of a restricted supply range. A practical design should include local decoupling, defined grounding, input overvoltage protection, and a power-gating arrangement if long-term battery life is critical.

Önerilen Ürünler Özeti

OPA2336 Dual-channel family member for equivalent signal conditioning Kullanıldığı Yer: Battery-Powered Sensor Conditioning, Portable Medical Instrument Signal Acquisition, Industrial Process Measurement, Low-Power Audio Interface, Data Acquisition and Instrumentation, IoT Edge Sensor Node OPA2336PA Dual-channel family member listed for comparison Kullanıldığı Yer: Battery-Powered Sensor Conditioning OPA4137P Higher-bandwidth dual-family comparator for faster acquisition designs Kullanıldığı Yer: Portable Medical Instrument Signal Acquisition, Industrial Process Measurement, Low-Power Audio Interface, Data Acquisition and Instrumentation, IoT Edge Sensor Node
What is the Texas Instruments OPA2336P?
The Texas Instruments OPA2336P is a dual-channel, single-supply microPower CMOS operational amplifier in an 8-pin DIP package. According to the manufacturer product information, the device provides rail-to-rail output, consumes 20 µA per amplifier, has a maximum input offset voltage of 125 µV, a 1 pA input bias current, and 115 dB of open-loop gain. Its dual configuration is useful for two-channel sensor conditioning, buffering, or general voltage-amplification circuits.
What is the operating voltage range of OPA2336P?
The OPA2336P operates from 2.3 V to 5.5 V. According to the Texas Instruments product information for the OPA2336 family, single-supply operation can begin at 2.3 V, making the amplifier suitable for low-voltage battery-powered systems. The manufacturer also identifies operation with a negative supply, although circuit-specific common-mode limits, input protection behavior, and output-swing conditions should be confirmed in the datasheet before use.
Where can I download the OPA2336P datasheet PDF?
The OPA2336P datasheet PDF is available through the Texas Instruments product page and the linked manufacturer-document copy. The manufacturer product page is https://www.ti.com/product/OPA2336, while a directly indexed PDF is https://pdf.digi-electronics.com/pdf/2579/OPA2336P-datasheet.pdf. Use the pin-description table, electrical-characteristics tables, and typical-application circuits in that document when assigning signals and designing the PCB.
Where can I find the OPA2336P pinout?
The OPA2336P pinout is documented in the manufacturer datasheet, which identifies the device as an 8-pin DIP with two operational-amplifier channels. Use the package drawing and pin-description table in the OPA2336 datasheet rather than inferring connections from a generic dual-op-amp diagram. In particular, confirm the two input pins, two output pins, supply pins, and the datasheet-prescribed connection for any unused channel.
What are the key specifications of OPA2336P that engineers should know?
The OPA2336P is a dual CMOS operational amplifier with a 2.3 V to 5.5 V supply range, rail-to-rail output, 20 µA quiescent current per amplifier, 125 µV maximum offset voltage, 1 pA input bias current, and 115 dB open-loop gain. According to the Texas Instruments product page, its listed gain-bandwidth product is 100 kHz and its slew rate is 0.03 V/µs. These specifications make it primarily suitable for low-power, low-to-moderate-bandwidth precision signal conditioning.
Is the OPA2336P suitable for battery-powered sensor interfaces?
Yes, the OPA2336P is well suited to many battery-powered sensor interfaces because its quiescent current is 20 µA per amplifier and its supply range begins at 2.3 V. The 1 pA input bias current also minimizes disturbance of high-impedance sources, while the 125 µV maximum offset voltage supports accurate small-signal measurement. Choose external resistor values and bypass capacitors that match the sensor impedance and supply current.
How much current does each OPA2336P amplifier channel consume?
Each OPA2336P amplifier channel has a quiescent current of 20 µA according to the Texas Instruments product information. Because the package contains two channels, the family-level quiescent-current figure should not be confused with the per-amplifier value. Actual circuit demand can be higher with a load, an operating mode, or an application-specific configuration, so power-budget calculations should include those additional effects and the datasheet test conditions.
What is the output swing of OPA2336P?
The OPA2336P provides rail-to-rail output operation according to the Texas Instruments product information. It can therefore approach the supply rails more closely than a conventional fixed-output amplifier, improving signal range in low-voltage systems. The exact output voltage under a specified load is not stated in the indexed product summary, so use the output-swing and output-current curves in the manufacturer datasheet when designing headroom-sensitive analog stages.
Where can I buy OPA2336P online?
Use the Request a Quote form on this page to request OPA2336P availability, current lead time, and order details. The verified product records include an explicit Texas Instruments 8-pin DIP listing, while the lifecycle record identifies OPA2336P as obsolete. Because availability can change after obsolescence, request a written quotation and current assembly or sourcing information before committing the component to a new production design.
What is the price of OPA2336P?
Use the Request a Quote form on this page for the current OPA2336P price, quantity breaks, stock position, and lead time. A listing displays a starting price, but that figure does not include the explicit quantity-break information required for reliable structured pricing and may not represent a purchaseable quantity. The quotation request provides a direct way to confirm the exact obsolete-part condition, packing, and available quantity for the required production quantity.
What is the lead time for OPA2336P?
The current lead time for OPA2336P should be confirmed through the Request a Quote form on this page. The part is identified as obsolete in a technical comparison record, so lead time can depend on remaining factory stock, distributor inventory, and the requested package or quantity. Ask the supplier to state the source, condition, quantity, and delivery schedule in the quotation rather than relying on a generic stock indicator.
Is OPA2336P in stock?
Stock for OPA2336P must be confirmed through the Request a Quote form because the component is identified as obsolete and inventory can change quickly. Some distributor records display an in-stock status or a nominal listing, but an explicit quantity for the requested production volume is required before scheduling an assembly build. The quotation should identify the exact MPN, package, quantity, date, and delivery commitment.
What is the best drop-in replacement for OPA2336P?
No replacement can be identified responsibly as a confirmed drop-in substitute from the available OPA2336P cross-reference records. The search results contain generic cross-reference tools but no manufacturer-supported, pin-compatible replacement with verified electrical specifications. OPA2336PA appears in a comparison result, but its exact package, pin mapping, lifecycle status, and full parameter differences require confirmation before it can be treated as a drop-in replacement.
Is OPA2336P the same as OPA2336PA?
No conclusion of equivalence should be made from the suffix alone. A manufacturer comparison result identifies OPA2336PA as another member of the dual microPower CMOS operational-amplifier family, but it does not establish that the part is a pin-compatible substitute for the obsolete OPA2336P. Compare the exact package drawing, pin assignments, supply range, offset, bias current, common-mode behavior, and lifecycle status in the manufacturer datasheets before considering a redesign.
When should I choose OPA2336P instead of OPA4137P?
Choose OPA2336P when a low-power, two-channel amplifier is required and a through-hole DIP package is acceptable. The OPA2336P has 20 µA quiescent current per amplifier, 100 kHz gain-bandwidth product, 0.03 V/µs slew rate, and 125 µV maximum offset voltage. A comparison record describes OPA4137P as a higher-bandwidth, higher-voltage part, making it more appropriate when speed, voltage range, or four-channel integration outweighs the OPA2336P's low-power DIP advantages.
What is the best cross-brand equivalent for OPA2336P?
A cross-brand equivalent cannot be confirmed from the available OPA2336P records because no manufacturer-specific candidate is identified with verified pin compatibility and matching electrical ratings. Search results show only general cross-reference tools rather than a validated substitute list. Before changing manufacturers, compare the 8-pin DIP footprint, two-channel pinout, 2.3 V to 5.5 V supply operation, rail-to-rail output, offset, bias current, bandwidth, slew rate, noise, and stability requirements.

Mühendislik referans verileri: OPA2336P — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose the OPA2336P for a new prototype or maintenance design that needs two low-power amplifier channels, rail-to-rail output, and operation down to 2.3 V. Its 20 µA quiescent current per amplifier, 1 pA input bias current, and 125 µV maximum offset voltage are particularly useful for battery-powered sensing and low-voltage instrumentation. The 100 kHz gain-bandwidth product and 0.03 V/µs slew rate also make it appropriate for slow sensor, speech, and general-purpose signal paths. Consider OPA4137P when four channels or substantially greater bandwidth and voltage range are needed, accepting higher power consumption. Do not assume OPA2336PA or any cross-brand part is a drop-in substitute until its package, pinout, electrical ratings, and lifecycle status have been verified. Because OPA2336P is identified as obsolete, production procurement should begin with a current quotation and a complete second-source validation plan.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün
Package 8-pin DIP
Brand Texas Instruments
Number of Channels 2 channels
Supply Voltage Range 2.3 V to 5.5 V
Quiescent Current 20 µA per amplifier
Input Offset Voltage 125 µV maximum
Input Bias Current 1 pA
Open-Loop Gain 115 dB
Gain-Bandwidth Product 100 kHz
Slew Rate 0.03 V/µs

Ana Farklılayıcılar

  • Exceptionally low quiescent current for a dual precision amplifier (karşılaştırma:OPA4137P)
  • Low-voltage operation with rail-to-rail output (karşılaştırma:OPA137U)
  • Precision input characteristics in a dual-channel package (karşılaştırma:OPA4137P)

Tasarım Notları

Place the supply bypass capacitor and any additional ceramic decoupling directly beside the OPA2336P power pins. Keep the input and output traces short, avoid routing them beside switching nodes or high-current return paths, and provide a low-impedance ground reference. Because this is a precision, low-current amplifier, PCB leakage and contamination can be more important than the nominal 1 pA bias-current specification in high-impedance layouts.

Do not treat rail-to-rail output as an unlimited output-current or load-capacitance capability. Confirm the output swing, output-current limits, and stable capacitive-load range in the manufacturer datasheet for the intended load. Also avoid leaving an unused amplifier input floating; follow the datasheet recommendation for biasing the unused channel so its output remains stable and does not interfere with the powered channel.

Estimated dual-channel quiescent power at a 3.3 V supply is 0.132 mW, calculated from 20 µA per amplifier, two amplifiers, and 3.3 V: 20 µA × 2 × 3.3 V = 132 µW. Actual supply current rises with output loading, switching activity, and the selected operating mode. Use this calculation only as a baseline and include regulator quiescent current, sensor current, and load demand in the complete battery-life budget.

Uyumluluk Bilgisi

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

RoHS compliance is identified in a technical comparison record. The listed operating temperature range is -55 °C to +125 °C. No confirmed automotive qualification or detailed substance-compliance information was identified.

İlgili Aramalar

OPA2336P datasheet OPA2336P pinout OPA2336P datasheet pdf OPA2336P specifications OPA2336P equivalent OPA2336P replacement OPA2336P cross reference OPA2336P vs OPA4137P OPA2336P footprint OPA2336P spice model Texas Instruments OPA2336P OPA2336P price OPA2336P stock OPA2336P DIP-8 pinout OPA2336P application circuit

İlgili Bileşenler ve Terimler

Texas Instruments OPA2336 OPA2336P OPA2336PA OPA4137P OPA137U dual operational amplifier microPower CMOS operational amplifier amplifier IC signal conditioning rail-to-rail output quiescent current input offset voltage input bias current open-loop gain gain-bandwidth product slew rate DIP-8 through-hole package battery-powered instrumentation high-impedance sensor single-supply operation RoHS chip select analog signal chain
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle