OPA2336U - Dual MicroPower Rail-to-Rail Op Amp | Texas Instruments
Артикул: OPA2336U ✓ АктивенOPA2336U Обзор
An operational amplifier is a high-gain analog building block that compares an input voltage with a feedback reference and amplifies the resulting error. Within the amplifier hierarchy, the OPA2336U is a CMOS voltage-feedback operational amplifier, a member of the MicroAmplifier family, and a dual alternative to the single-channel OPA336. It is designed for low-voltage signal conditioning rather than high-speed or high-precision instrumentation.
Key features include a maximum input offset voltage of 125 µV, input bias current of 1 pA, and open-loop gain of 115 dB. These characteristics support accurate current sensing and sensor interfaces when operating current is low. Rail-to-rail output behavior also improves dynamic range in low-voltage systems where conventional output stages would clip near the positive rail.
The OPA2336 family uses a CMOS input stage for very low bias current and low quiescent power consumption. Its common-mode input range extends to the negative supply, which simplifies single-supply operation because input signals can approach ground. The 100 kHz bandwidth is sufficient for audio-frequency buffers, sensor conditioners, and low-speed control loops, while the 0.03 V/µs slew rate limits large-signal response.
Typical applications include portable sensor measurement, low-current battery monitoring, audio preamplification, microphone conditioning, biomedical instrumentation, and low-power control systems. The SOIC-8 package provides a widely used footprint, while the low 20 µA per-amplifier quiescent current supports longer battery life in sensor nodes and handheld instruments.
When designing around the OPA2336U, verify the input common-mode range and output-swing limits against the actual signal amplitude. Decoupling capacitors should be placed close to the supply pins, and the circuit should be checked for stability with the intended load capacitance and feedback network.
This page combines manufacturer specifications, practical application guidance, drop-in replacement information, and design notes that help engineers evaluate the OPA2336U alongside other low-power dual operational amplifiers.
Аналоги без доработки для OPA2336U — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
OPA2336UA
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
OPA2336U Максимальные параметры и электрические характеристики
| Number of Amplifiers | 2 amplifiers |
| Amplifier Type | Single-supply, microPower CMOS operational amplifier |
| Supply Voltage Range | 2.3 V to 5.5 V |
| Minimum Single-Supply Operation | 2.1 V |
| Gain-Bandwidth Product | 100 kHz |
| Slew Rate | 0.03 V/µs |
| Ток покоя | 20 µA per amplifier |
| Maximum Input Offset Voltage | 125 µV |
| Input Bias Current | 1 pA |
| Open-Loop Gain | 115 dB |
| Output Swing | Within 3 mV of the supply rails at 100 kΩ load |
| Input Common-Mode Range | Extends to the negative supply |
| Корпус | 8-pin SOIC |
| Тип монтажа | Surface mount |
| Диапазон рабочих температур | -40 °C to +85 °C standard; -55 °C to +125 °C extended |
Конфигурация выводов OPA2336U
| Контакт 1 | OUTA — Amplifier A output |
| Контакт 2 | INA- — Amplifier A inverting input |
| Контакт 3 | INA+ — Amplifier A non-inverting input |
| Контакт 4 | V- — Negative supply connection |
| Контакт 5 | INB+ — Amplifier B non-inverting input |
| Контакт 6 | INB- — Amplifier B inverting input |
| Контакт 7 | OUTB — Amplifier B output |
| Контакт 8 | V+ — Positive supply connection |
Типичное применение
OPA2336U подходит для 6 применениеs: Portable Sensor Signal Conditioning, Low-Current Battery Monitoring, Microphone and Audio Preconditioning, Low-Power Current-to-Voltage Conversion, Medical and Bio-Signal Buffering, Portable Instrumentation and Control Loops.
Portable Sensor Signal Conditioning
The OPA2336U fits battery-powered sensor nodes because both amplifiers operate from 2.3 V to 5.5 V and draw only 20 µA per amplifier at quiescence. Its 1 pA input bias current limits disturbance of high-impedance sources, while the 115 dB open-loop gain supports accurate amplification around a stable reference. Place the device close to the sensor interface, use the negative supply as the analog ground reference, and bypass the supply locally. The 100 kHz bandwidth comfortably covers slow temperature, pressure, and chemical sensor signals without adding meaningful power cost.
Рекомендуется
Low-Current Battery Monitoring
The OPA2336U is useful for amplifying the small voltage produced by a shunt in a low-current battery monitor. The 1 pA input bias current minimizes measurement error through high-value shunt resistors, and the rail-to-rail output allows the signal to approach the available supply range. Its 125 µV maximum input offset voltage must be included in the error budget when resolving microampere-level currents. Because the device consumes 20 µA per amplifier, the dual configuration can provide gain and buffering without doubling the support circuitry.
Рекомендуется
Microphone and Audio Preconditioning
The OPA2336U can buffer low-level microphone or audio-sensor outputs in compact audio modules. Its rail-to-rail output reduces clipping near the positive supply, while the 100 kHz gain-bandwidth product supports audio-band amplification when used with modest closed-loop gains. Two amplifiers in one package allow one channel to condition the signal and the other to drive or filter a subsequent stage. The 0.03 V/µs slew rate is adequate for low-frequency audio but does not support high-fidelity video or ultrasonic signal paths.
Рекомендуется
Low-Power Current-to-Voltage Conversion
The OPA2336U can implement a transimpedance or current-to-voltage stage for photodiode and sensor-current measurements. Its 1 pA input bias current is a major benefit when the source impedance is high, since bias-related error otherwise multiplies across the feedback resistor. The 100 kHz bandwidth limits how quickly the loop can respond, while the 3 mV rail-to-rail output headroom must be considered when a full-scale signal approaches the supply. Add the specified compensation capacitance required for stable operation with the selected feedback resistance and total input capacitance.
Рекомендуется
Medical and Bio-Signal Buffering
The OPA2336U is suitable for low-level biomedical buffering when the design operates from a single low-voltage supply. Its rail-to-rail input and output characteristics, 1 pA input bias current, and 20 µA per-amplifier quiescent current suit portable monitors that must limit both loading and standby power. However, medical designs require validation of noise, leakage, offset stability, and applicable safety requirements for the complete system. The 100 kHz bandwidth is appropriate for many ECG, temperature, and physiological-pressure front ends but not for demanding diagnostic bandwidth.
Рекомендуется
Portable Instrumentation and Control Loops
The OPA2336U fits handheld instruments where two amplifiers are needed for active filtering, error amplification, or output buffering. The 115 dB open-loop gain provides useful loop gain at low frequencies, and the negative-supply common-mode range simplifies circuits referenced to analog ground. Its low quiescent current supports longer operating time between battery charges, while the 8-pin SOIC package remains easy to assemble. Keep the feedback network compact and verify stability against load capacitance because the 0.03 V/µs slew rate and 100 kHz bandwidth limit large-signal and high-speed behavior.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для OPA2336U — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | OPA2336UA |
|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments |
| Number of Amplifiers | 2 amplifiers | 2 amplifiers |
| Supply Voltage Range | 2.3 V to 5.5 V | 2.3 V to 5.5 V |
| Gain-Bandwidth Product | 100 kHz | 100 kHz |
| Slew Rate | 0.03 V/µs | 0.03 V/µs |
| Quiescent Current | 20 µA per amplifier | 20 µA per amplifier |
| Maximum Input Offset Voltage | 125 µV | 125 µV |
| Input Bias Current | 1 pA | 1 pA |
| Open-Loop Gain | 115 dB | 115 dB |
Ключевые отличия
- Dual microPower CMOS amplification in one package (против OPA2336UA)
- Rail-to-rail output operation for low-voltage systems (против OPA2336UA)
- Very low input bias current for high-impedance sources (против OPA2336UA)
Заметки по проектированию
The dual amplifier consumes approximately 20 µA per amplifier at quiescence, so the device accounts for about 40 µA before feedback-network and load contributions are added. For battery-powered designs, include the quiescent current of both channels when calculating the operating budget. Place the supply bypass capacitor adjacent to pin 8 and provide a short ground return from pin 4.
The 100 kHz gain-bandwidth product and 0.03 V/µs slew rate set practical limits for closed-loop bandwidth and large-signal response. Avoid operating the amplifier close to its bandwidth limit, because phase margin and slew-rate distortion can increase sharply. Keep feedback components compact and use guarding for high-impedance inputs to reduce leakage and capacitive pickup.
Do not assume the output can reach either supply rail exactly. The published output swing is within 3 mV of the rails at a 100 kΩ load, and the usable headroom changes with load and output current. Similarly, the input common-mode range extends to the negative supply but is not unlimited at the positive end. Check the manufacturer characteristic curves for the actual signal amplitude and load.
Place the bypass capacitor at the positive supply pin and route the negative supply directly to the ground plane. Keep input and feedback traces short and separate them from switching-node and high-current return paths. Since both amplifiers share the same supply pins, a single noisy load connected to one channel can couple into the other through supply impedance and board-current paths.
Информация о соответствии
The OPA2336 family is intended for battery-powered applications, but no explicit RoHS, REACH, halogen-free, or conflict-minerals declaration is included in the available product information. Confirm compliance documentation with Texas Instruments for the selected ordering code.