Texas Instruments

OPA2336U - Dual MicroPower Rail-to-Rail Op Amp | Texas Instruments

MPN: OPA2336U ✓ Hoạt động
2.3 V to 5.5 V Vdss 20 µA per amplifier Id 8-pin SOIC Package
MOQ: 1 |

OPA2336U Tóm tắt

The Texas Instruments OPA2336U is a dual, single-supply, microPower CMOS operational amplifier in an 8-pin SOIC package. It combines a 2.3 V to 5.5 V supply range, 100 kHz gain-bandwidth product, 0.03 V/µs slew rate, and low 20 µA quiescent current per amplifier, making it suitable for compact battery-powered and portable systems. Each amplifier provides rail-to-rail output swing to within 3 mV of the supply rails with a 100 kΩ load.

An operational amplifier is a high-gain analog building block that compares an input voltage with a feedback reference and amplifies the resulting error. Within the amplifier hierarchy, the OPA2336U is a CMOS voltage-feedback operational amplifier, a member of the MicroAmplifier family, and a dual alternative to the single-channel OPA336. It is designed for low-voltage signal conditioning rather than high-speed or high-precision instrumentation.

Key features include a maximum input offset voltage of 125 µV, input bias current of 1 pA, and open-loop gain of 115 dB. These characteristics support accurate current sensing and sensor interfaces when operating current is low. Rail-to-rail output behavior also improves dynamic range in low-voltage systems where conventional output stages would clip near the positive rail.

The OPA2336 family uses a CMOS input stage for very low bias current and low quiescent power consumption. Its common-mode input range extends to the negative supply, which simplifies single-supply operation because input signals can approach ground. The 100 kHz bandwidth is sufficient for audio-frequency buffers, sensor conditioners, and low-speed control loops, while the 0.03 V/µs slew rate limits large-signal response.

Typical applications include portable sensor measurement, low-current battery monitoring, audio preamplification, microphone conditioning, biomedical instrumentation, and low-power control systems. The SOIC-8 package provides a widely used footprint, while the low 20 µA per-amplifier quiescent current supports longer battery life in sensor nodes and handheld instruments.

When designing around the OPA2336U, verify the input common-mode range and output-swing limits against the actual signal amplitude. Decoupling capacitors should be placed close to the supply pins, and the circuit should be checked for stability with the intended load capacitance and feedback network.

This page combines manufacturer specifications, practical application guidance, drop-in replacement information, and design notes that help engineers evaluate the OPA2336U alongside other low-power dual operational amplifiers.

Bộ thay thế dễ dàng lắp đặt cho OPA2336U — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

OPA2336UA

✅ Drop-In
📦 8-pin SOIC
Same OPA2336 dual CMOS core, 100 kHz bandwidth, and 0.03 V/µs slew rate; ordering suffix differs by 0% in core electrical ratings

📋 Tham chiếu thay thế (không có trong danh mục)

OPA2336U Tỷ lệ tối đa & tính chất điện

Number of Amplifiers 2 amplifiers
Amplifier Type Single-supply, microPower CMOS operational amplifier
Supply Voltage Range 2.3 V to 5.5 V
Minimum Single-Supply Operation 2.1 V
Gain-Bandwidth Product 100 kHz
Slew Rate 0.03 V/µs
Điện áp yên tĩnh 20 µA per amplifier
Maximum Input Offset Voltage 125 µV
Input Bias Current 1 pA
Open-Loop Gain 115 dB
Output Swing Within 3 mV of the supply rails at 100 kΩ load
Input Common-Mode Range Extends to the negative supply
Hộp 8-pin SOIC
Kiểu lắp đặt Surface mount
Khoảng nhiệt độ hoạt động -40 °C to +85 °C standard; -55 °C to +125 °C extended

Cấu hình chân OPA2336U

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Chân 1 OUTA — Amplifier A output
Chân 2 INA- — Amplifier A inverting input
Chân 3 INA+ — Amplifier A non-inverting input
Chân 4 V- — Negative supply connection
Chân 5 INB+ — Amplifier B non-inverting input
Chân 6 INB- — Amplifier B inverting input
Chân 7 OUTB — Amplifier B output
Chân 8 V+ — Positive supply connection

Ứng dụng tiêu biểu

OPA2336U phù hợp cho 6 Áp dụngs: Portable Sensor Signal Conditioning, Low-Current Battery Monitoring, Microphone and Audio Preconditioning, Low-Power Current-to-Voltage Conversion, Medical and Bio-Signal Buffering, Portable Instrumentation and Control Loops.

🧩

Portable Sensor Signal Conditioning

The OPA2336U fits battery-powered sensor nodes because both amplifiers operate from 2.3 V to 5.5 V and draw only 20 µA per amplifier at quiescence. Its 1 pA input bias current limits disturbance of high-impedance sources, while the 115 dB open-loop gain supports accurate amplification around a stable reference. Place the device close to the sensor interface, use the negative supply as the analog ground reference, and bypass the supply locally. The 100 kHz bandwidth comfortably covers slow temperature, pressure, and chemical sensor signals without adding meaningful power cost.

⚡

Low-Current Battery Monitoring

The OPA2336U is useful for amplifying the small voltage produced by a shunt in a low-current battery monitor. The 1 pA input bias current minimizes measurement error through high-value shunt resistors, and the rail-to-rail output allows the signal to approach the available supply range. Its 125 µV maximum input offset voltage must be included in the error budget when resolving microampere-level currents. Because the device consumes 20 µA per amplifier, the dual configuration can provide gain and buffering without doubling the support circuitry.

🎧

Microphone and Audio Preconditioning

The OPA2336U can buffer low-level microphone or audio-sensor outputs in compact audio modules. Its rail-to-rail output reduces clipping near the positive supply, while the 100 kHz gain-bandwidth product supports audio-band amplification when used with modest closed-loop gains. Two amplifiers in one package allow one channel to condition the signal and the other to drive or filter a subsequent stage. The 0.03 V/µs slew rate is adequate for low-frequency audio but does not support high-fidelity video or ultrasonic signal paths.

📷

Low-Power Current-to-Voltage Conversion

The OPA2336U can implement a transimpedance or current-to-voltage stage for photodiode and sensor-current measurements. Its 1 pA input bias current is a major benefit when the source impedance is high, since bias-related error otherwise multiplies across the feedback resistor. The 100 kHz bandwidth limits how quickly the loop can respond, while the 3 mV rail-to-rail output headroom must be considered when a full-scale signal approaches the supply. Add the specified compensation capacitance required for stable operation with the selected feedback resistance and total input capacitance.

💊

Medical and Bio-Signal Buffering

The OPA2336U is suitable for low-level biomedical buffering when the design operates from a single low-voltage supply. Its rail-to-rail input and output characteristics, 1 pA input bias current, and 20 µA per-amplifier quiescent current suit portable monitors that must limit both loading and standby power. However, medical designs require validation of noise, leakage, offset stability, and applicable safety requirements for the complete system. The 100 kHz bandwidth is appropriate for many ECG, temperature, and physiological-pressure front ends but not for demanding diagnostic bandwidth.

🔧

Portable Instrumentation and Control Loops

The OPA2336U fits handheld instruments where two amplifiers are needed for active filtering, error amplification, or output buffering. The 115 dB open-loop gain provides useful loop gain at low frequencies, and the negative-supply common-mode range simplifies circuits referenced to analog ground. Its low quiescent current supports longer operating time between battery charges, while the 8-pin SOIC package remains easy to assemble. Keep the feedback network compact and verify stability against load capacitance because the 0.03 V/µs slew rate and 100 kHz bandwidth limit large-signal and high-speed behavior.

Tóm tắt các sản phẩm được đề xuất

OPA2336UA Same dual amplifier family for alternate ordering code Được sử dụng trong: Portable Sensor Signal Conditioning, Low-Current Battery Monitoring, Microphone and Audio Preconditioning, Low-Power Current-to-Voltage Conversion, Medical and Bio-Signal Buffering, Portable Instrumentation and Control Loops
What is the operating voltage range of OPA2336U?
The OPA2336U operates from a 2.3 V to 5.5 V supply in the published specifications, and the OPA336 family is designed for single-supply operation as low as 2.1 V. According to the Texas Instruments OPA2336 product page and data sheet, this makes the dual amplifier suitable for low-voltage battery systems that cannot support a conventional 5 V-only op amp.
What are the key specifications of OPA2336U?
The OPA2336U is a dual microPower CMOS op amp with 100 kHz gain-bandwidth product, 0.03 V/µs slew rate, 20 µA quiescent current per amplifier, 125 µV maximum offset voltage, 1 pA input bias current, and 115 dB open-loop gain. Texas Instruments also describes rail-to-rail output swing to within 3 mV of the rails at a 100 kΩ load.
Is OPA2336U rail-to-rail?
Yes, the OPA2336U provides rail-to-rail output operation and swings to within 3 mV of the supply rails with a 100 kΩ load. Its input common-mode range extends to the negative supply, which is particularly useful for single-supply sensing circuits. Texas Instruments describes this behavior in the OPA2336 family documentation.
How much current does OPA2336U consume?
The OPA2336U consumes approximately 20 µA of quiescent current per amplifier, or about 40 µA for the dual device before output-current and feedback-network contributions are considered. The Texas Instruments product page lists this low-power figure as a key advantage for battery-powered applications.
Where can I download the OPA2336U datasheet PDF?
The official OPA2336U data sheet is available through the Texas Instruments product page and its linked literature entry. The manufacturer product page is at https://www.ti.com/product/OPA2336, while the literature download is at https://www.ti.com/lit/gpn/OPA2336. Use the manufacturer document for pin assignments, test conditions, and full characteristic curves.
What is the pinout of OPA2336U?
The OPA2336U uses a standard dual-operational-amplifier arrangement in an 8-pin SOIC: output A, inverting input A, non-inverting input A, negative supply, non-inverting input B, inverting input B, output B, and positive supply. Use the pin-description table in the Texas Instruments data sheet when assigning PCB tracks.
What can replace the OPA2336U?
The OPA2336UA is a drop-in candidate for the OPA2336U because it represents the same dual OPA2336 family in the same 8-pin SOIC footprint. It matches the 100 kHz bandwidth, 0.03 V/µs slew rate, and low-power CMOS architecture. Confirm temperature grade, tape-and-reel ordering, and production requirements before substituting.
Is OPA2336UA the same as OPA2336U?
The OPA2336UA and OPA2336U are closely related dual microPower CMOS op amps in the same 8-pin SOIC package with equivalent core performance, including 100 kHz bandwidth and 0.03 V/µs slew rate. Ordering-code differences can indicate temperature-grade or packing differences, so verify the full device status against the manufacturer data sheet.
When should I choose OPA2336U over a precision op amp?
Choose the OPA2336U when battery power, small signal bandwidth, and rail-to-rail output swing matter more than very low offset drift. It combines 125 µV maximum offset, 1 pA bias current, and 115 dB open-loop gain with only 20 µA per amplifier. For instrumentation requiring drift specifications or gain accuracy far beyond these levels, select a higher-precision device instead.
Is OPA2336U suitable for battery-powered sensor circuits?
Yes, the OPA2336U is well suited to battery-powered sensor circuits because it operates from a low single supply, draws 20 µA per amplifier, and provides rail-to-rail output swing. Its 1 pA input bias current also reduces error when measuring high-impedance sensor sources. Overall accuracy will still depend on offset, noise, and resistor selection.
OPA2336U vs OPA2336UA - which is the better drop-in replacement?
The OPA2336UA is the closest drop-in alternative listed for the OPA2336U because both are dual OPA2336-family devices in an 8-pin SOIC with 100 kHz bandwidth and 0.03 V/µs slew rate. The practical difference is the ordering suffix rather than the core analog function. Confirm the temperature grade and mechanical packing before production use.
What are the best Texas Instruments alternatives to OPA2336U?
The closest Texas Instruments drop-in candidate is the OPA2336UA, which uses the same 8-pin SOIC footprint and the same dual microPower CMOS amplifier core. Other OPA336-family single amplifiers require a different channel count, so they are not direct replacements for a dual-circuit PCB. Compare complete device functions before treating any candidate as equivalent.
Does the OPA2336U need an external supply decoupling capacitor?
Place a local bypass capacitor close to the positive supply pin and connect the negative supply pin to the ground plane with a short return path. Exact capacitor values and stability requirements should be taken from the manufacturer data sheet and application guidance. Decoupling is especially important when the op amp operates next to switching converters or noisy digital circuitry.
Is the OPA2336U still active?
The OPA2336U is treated as an active Texas Instruments product for this listing, with current product-page and distributor listings available. Texas Instruments also states that the single, dual, and quad versions share identical specifications for design flexibility. Check the manufacturer product page for the latest lifecycle statement before committing a long-lived design.
Where can I buy OPA2336U online and what is its price?
The OPA2336U is available from authorized electronics distributors, but current commercial terms change by volume, inventory, and purchasing date. Use the Request a Quote form on this page to request current pricing, stock, and lead-time information for OPA2336U. The same form can provide volume-break quotes for prototype or production quantities.
What is the lead time and stock status for OPA2336U?
Current stock and lead time for OPA2336U depend on warehouse inventory and replenishment conditions at the time of purchase. Request a quote through the Request a Quote form on this page for the latest allocation, volume pricing, and expected delivery information. For a scheduled production program, state your required dates and annual usage in the request.

Dữ liệu tham khảo kỹ thuật cho OPA2336U — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the OPA2336U when the design needs two low-power, rail-to-rail CMOS amplifiers in a standard 8-pin SOIC footprint. Its 20 µA per-amplifier quiescent current, 125 µV maximum offset, 1 pA bias current, and 100 kHz bandwidth make it a strong fit for portable sensing, low-current battery monitoring, audio buffering, and instrumentation referenced to a single supply. The OPA2336UA is the closest alternative because it retains the same dual amplifier core, electrical performance, and package; choose it when its ordering suffix matches the required temperature grade or packing configuration. Neither part is a drop-in substitute for a single-channel OPA336, nor should either be selected for high-speed video, precision drift-critical measurement, or applications requiring more bandwidth than the 100 kHz gain-bandwidth product can provide.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này OPA2336UA
Package 8-pin SOIC 8-pin SOIC
Brand Texas Instruments Texas Instruments
Number of Amplifiers 2 amplifiers 2 amplifiers
Supply Voltage Range 2.3 V to 5.5 V 2.3 V to 5.5 V
Gain-Bandwidth Product 100 kHz 100 kHz
Slew Rate 0.03 V/µs 0.03 V/µs
Quiescent Current 20 µA per amplifier 20 µA per amplifier
Maximum Input Offset Voltage 125 µV 125 µV
Input Bias Current 1 pA 1 pA
Open-Loop Gain 115 dB 115 dB

Bảo phân biệt quan trọng

  • Dual microPower CMOS amplification in one package (vsOPA2336UA)
  • Rail-to-rail output operation for low-voltage systems (vsOPA2336UA)
  • Very low input bias current for high-impedance sources (vsOPA2336UA)

Ghi chú thiết kế

The dual amplifier consumes approximately 20 µA per amplifier at quiescence, so the device accounts for about 40 µA before feedback-network and load contributions are added. For battery-powered designs, include the quiescent current of both channels when calculating the operating budget. Place the supply bypass capacitor adjacent to pin 8 and provide a short ground return from pin 4.

The 100 kHz gain-bandwidth product and 0.03 V/µs slew rate set practical limits for closed-loop bandwidth and large-signal response. Avoid operating the amplifier close to its bandwidth limit, because phase margin and slew-rate distortion can increase sharply. Keep feedback components compact and use guarding for high-impedance inputs to reduce leakage and capacitive pickup.

Do not assume the output can reach either supply rail exactly. The published output swing is within 3 mV of the rails at a 100 kΩ load, and the usable headroom changes with load and output current. Similarly, the input common-mode range extends to the negative supply but is not unlimited at the positive end. Check the manufacturer characteristic curves for the actual signal amplitude and load.

Place the bypass capacitor at the positive supply pin and route the negative supply directly to the ground plane. Keep input and feedback traces short and separate them from switching-node and high-current return paths. Since both amplifiers share the same supply pins, a single noisy load connected to one channel can couple into the other through supply impedance and board-current paths.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The OPA2336 family is intended for battery-powered applications, but no explicit RoHS, REACH, halogen-free, or conflict-minerals declaration is included in the available product information. Confirm compliance documentation with Texas Instruments for the selected ordering code.

Dữ liệu được xác minh vào: 2026-11-09 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

OPA2336U datasheet OPA2336U datasheet pdf OPA2336U pinout OPA2336U specifications Texas Instruments OPA2336U OPA2336U SOIC-8 pinout OPA2336U drop-in replacement OPA2336U vs OPA2336UA OPA2336U equivalent dual op amp OPA2336U rail-to-rail op amp OPA2336U battery powered application OPA2336U price OPA2336U stock and lead time OPA2336U application circuit

Các bộ phận và thuật ngữ liên quan

Texas Instruments OPA2336U OPA2336UA OPA2336 OPA336 dual operational amplifier MicroAmplifier CMOS operational amplifier voltage-feedback amplifier analog IC integrated circuit semiconductor rail-to-rail output input bias current input offset voltage open-loop gain gain-bandwidth product slew rate quiescent current common-mode input range 8-pin SOIC SOIC package family surface-mount package battery-powered applications sensor signal conditioning RoHS REACH
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ