PCA9514D - 400kHz Hot-Swappable SMBus Buffer | NXP
Артикул: PCA9514D ✗ Снят с производстваPCA9514D Обзор
An SMBus buffer is an interface IC that separates two bus segments so that capacitance, voltage differences, or temporarily disconnected devices do not disrupt the complete bus. In the wider product hierarchy, this buffer belongs to the I2C and SMBus interface family, which sits within interface ICs and system-level data-management electronics. Unlike a passive series resistor, a buffered hot-plug solution can isolate the bus during insertion or removal while maintaining defined logic levels across the separated segments.
The primary advantage of the PCA9514D is hot-swap bus isolation at a maximum stated frequency of 400 kHz. This makes it relevant to systems where modules may be added or removed after power is applied, including expandable industrial equipment, removable control modules, and board-to-board backplanes. The single-channel arrangement allows a designer to isolate one bus branch without introducing a multi-channel or bidirectional buffer architecture.
The PCA9514D uses NXP's 8-SO package, a compact surface-mount package suitable for conventional PCB assembly and automated manufacturing. Because it is a dedicated interface device, its principal design concerns are bus logic levels, pull-up placement, enable or connection timing, signal integrity, and the voltage relationship between the two bus sides. Detailed supply limits, channel voltage tolerance, propagation timing, and electrical characteristics should be taken directly from the manufacturer datasheet when those values are required for a production design.
Typical uses include hot-pluggable sensor and storage modules, removable front-panel controllers, distributed data-acquisition equipment, and board-to-board I2C links. In an industrial enclosure, the device can help prevent a faulty or newly inserted card from loading the main SMBus. In a portable or modular product, it can support a controlled connection sequence. The buffer does not eliminate the need for correct pull-up resistors or bus timing analysis; it provides the isolation element around which those network decisions are made.
Designers should verify enable sequencing, pull-up resistor locations, capacitance, and logic-level compatibility before finalizing the PCB. Keep both sides of the buffer routed with short, continuous return paths, and place associated protection or pull-up components close to their relevant pins. Review the datasheet pin-description and application diagrams when assigning tracks, particularly if a design uses the device for bidirectional bus translation rather than straightforward same-domain buffering.
This page combines the NXP product status, package and bus-frequency information with design-focused guidance for obsolete-product review, replacement planning, and hot-pluggable bus architecture decisions. It also separates the exact orderable PCA9514D references from broader interface-design considerations so engineers can evaluate lifecycle constraints without overlooking implementation details.
Аналоги без доработки для PCA9514D — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
PCA9514D,112
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PCA9514D,118
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PCA9514AD,118
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PCA9514D Характеристики
| Channel Count | 1 channel |
| Maximum Bus Frequency | 400 kHz |
| Supported Bus Type | SMBus |
| Hot-Plug Function | Hot-swappable bus isolation |
| Buffer Type | Bus buffer and accelerator |
| Корпус | 8-SO |
| Package Pin Count | 8 pins |
| Тип монтажа | Surface mount |
| Manufacturer Lifecycle Status | No longer manufactured |
Руководство по цоколевке PCA9514D в корпусе 8 pins
Цоколевка для PCA9514D (корпус 8 pins). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для PCA9514D.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
PCA9514D подходит для 6 применениеs: Hot-Pluggable Sensor Modules, Industrial Data-Acquisition Systems, Removable Front-Panel Controllers, Board-to-Backplane Communication, Portable Diagnostic and Test Equipment, Removable Storage and Memory Modules.
Hot-Pluggable Sensor Modules
The PCA9514D fits modular sensor systems in which an external I2C or SMBus device may be attached while the host remains powered. Placing the single buffer between the host bus and the removable sensor branch isolates the branch during connection, reducing the chance that cable capacitance or an unsettled device state will disturb the main bus. The documented 400 kHz maximum supports Fast-mode-class communication while preserving a dedicated path for one module. Designers should still route both bus sides as short, continuous networks, verify pull-up values, and confirm the device's enable sequence in the manufacturer application guidance.
Рекомендуется
Industrial Data-Acquisition Systems
The PCA9514D is useful in industrial data-acquisition equipment where remote sensor cards or measurement modules can be replaced during maintenance. Its hot-swappable buffer function prevents the removable branch from coupling directly to the primary SMBus, allowing the main controller to continue operating while a module is inserted. The single-channel structure is appropriate when each card requires one isolated bus segment, and the 400 kHz rate is sufficient for many register-oriented sensor buses. The enclosure, grounding, cable length, and electrostatic-protection design remain important because the buffer isolates the bus but does not replace surge protection or proper signal conditioning.
Рекомендуется
Removable Front-Panel Controllers
A removable display or keypad controller can be placed behind a PCA9514D so that its I2C or SMBus connection does not load the host bus during removal or installation. The buffer's hot-swappable characteristic allows the equipment to control the attachment sequence more reliably than an unprotected direct connection, while its 400 kHz maximum gives adequate bandwidth for typical control traffic. In a panel design, keep the protected and isolated sides separated in the layout, maintain a continuous ground path under the data route, and review the manufacturer diagram to implement the intended enable state during power-up and hot-plug events.
Рекомендуется
Board-to-Backplane Communication
The PCA9514D can isolate a card-edge I2C or SMBus connection on a backplane where boards may be inserted, removed, or serviced without powering down the complete system. The buffer creates a controlled boundary between the system bus and the card bus, which can reduce disturbance from connected circuitry and cable capacitance. Its single-channel architecture suits one isolated branch per buffer, while the 400 kHz rating supports many management and configuration buses. Backplane implementations should control bus enable timing, account for connector and cable capacitance, and use a low-impedance ground plane to preserve signal integrity across the divided bus segments.
Рекомендуется
Portable Diagnostic and Test Equipment
PCA9514D can support diagnostic probe modules or interchangeable test cards that attach to a portable instrument through an I2C or SMBus connection. Hot-swappable isolation reduces disruption when a probe is changed, and the 400 kHz operating limit is suitable for configuration and measurement-control traffic rather than high-bandwidth data transfer. The design should include a deliberate enable sequence so that both bus sides reach valid levels before communication begins. Probe cables also require careful return-path construction and protection against external transients because bus isolation alone does not provide complete electrical isolation from the instrument ground.
Рекомендуется
Removable Storage and Memory Modules
A PCA9514D can isolate a removable memory or storage controller that uses SMBus or I2C for configuration and status reporting. The buffer allows the module side to be disconnected without allowing the controller's bus loading to disturb the main bus. Its 400 kHz rate is appropriate for command, configuration, and status traffic rather than payload transfer, and the single-channel format allows each removable module to use a dedicated isolation point. The implementation should preserve the intended idle state, verify connector capacitance, and separate data and return paths so that the hot-plug transition does not create ringing or unintended current.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PCA9514D — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PCA9514D,112 | PCA9514D,118 | PCA9514AD,118 |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 8-SO / SOIC-8 | 8-SO / SOIC-8 | 8-SO / SOIC-8 | 8-SO / SOIC-8 |
| Device Type | Hot-swappable SMBus buffer | Hot-swappable SMBus buffer | Hot-swappable SMBus buffer | Buffer, accelerator, I2C hot-swap interface |
| Supported Bus | SMBus / I2C | SMBus / I2C | SMBus / I2C | I2C hot-swap interface |
| Pin Compatibility | 8-pin pin arrangement | Stated completely replaceable | Stated consistent terminals and package | Stated consistent terminals and package |
| Key Ordering Difference | Base designation | Orderable suffix 112 | Orderable suffix 118 | Additional AD designation and suffix 118 |
Ключевые отличия
- Purpose-built hot-swappable SMBus isolation (против PCA9514AD,118)
- Exact 8-pin package continuity for legacy boards (против PCA9514D,118)
- Documented complete replacement path (против PCA9514D,112)
Заметки по проектированию
Route the host-side and isolated-side I2C or SMBus networks as separate branches, with short traces and a continuous ground reference. Place pull-up resistors on the appropriate bus segment according to the manufacturer application diagram; adding them indiscriminately to both sides can produce unintended parallel pull-up strength and alter rise time. Keep connector and cable capacitance away from the host-side routing whenever the PCA9514D is intended to isolate that branch.
Do not treat the PCA9514D as a complete substitute for electrical isolation. The device buffers and isolates the bus path, but it does not necessarily provide galvanic isolation between the two sides. Review the exact datasheet voltage limits, enable behavior, and truth states before using it with independently powered domains. For maintenance-friendly equipment, define a safe sequence that keeps the bus in an inactive state during insertion or removal.
Check the combined capacitance of devices, connectors, and cables against the rise-time budget for the 400 kHz bus. Use the shortest practical routing, maintain a low-impedance return path, and observe the manufacturer's enable timing. When a branch has long wiring or several pull-ups, evaluate the bus with an oscilloscope after hot-plug insertion to check for ringing, excessive overshoot, or an unintended low state.
Preserve the manufacturer's pin and application layout when adapting a legacy PCA9514D board. The 8-SO footprint is only the starting point: enable traces, supply decoupling, pull-up placement, and exposed copper around surrounding circuitry determine whether hot-swap behavior remains reliable. For a transfer to another orderable suffix, compare the complete pin-description table and note any differences in lifecycle, temperature grade, or packing before releasing the PCB files.
Информация о соответствии
The available product information identifies the lifecycle state and core interface characteristics but does not provide the package-specific compliance declarations required to populate these fields.