PCA9554DB - 8-Bit I2C I/O Expander, 5.5V | TI
Артикул: PCA9554DB ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $1.3604 | $1,36 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
PCA9554DB Обзор
An I/O expander is an interface IC that increases the number of input and output lines available to a microcontroller or other host processor. The PCA9554 belongs to the I2C interface-controller hierarchy: it connects through the two-line bidirectional bus using SCL and SDA, while its eight parallel pins can be configured individually as inputs or outputs. This makes it useful when a system needs remote control, monitoring, or signal-interface expansion without adding a larger microcontroller package.
The verified listing identifies weak pull-ups, an interrupt output, and configuration registers as defining features. Configuration registers allow the host to define each port direction and control output states, while the interrupt output provides a change notification mechanism for input events. The 2.3 V to 5.5 V operating range supports both low-voltage and conventional 5 V system rails, subject to the host and bus requirements.
The PCA9554DB is identified as a 16-SSOP I/O expander by DigiKey, with an operating bus frequency of 400 kHz. This combination of eight configurable I/O lines, interrupt support, and a compact surface-mount package makes the device suitable for embedded control, remote sensing, keypad or display interfaces, and small automation systems.
Designers should confirm the device address, pull-up implementation, electrical limits, and interrupt polarity against the manufacturer datasheet before finalizing a board. The verified data does not provide pin-level naming, output-current limits, or detailed timing values, so those parameters require verification rather than assumption.
Аналоги без доработки для PCA9554DB — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PCA9554DB (тот же форм-фактор и посадочное место) — отличается по Interrupt Output, Package.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PCA9554DB
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →PCA9554ABS3,118
✅ Прямая замена✓ В наличии
$0.78 / шт.
Открыть даташит →TCA9554PWR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TCA9554ADBR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PCA9534DB
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PCA9554DB Характеристики
| Функция | 8-bit I2C/SMBus I/O expander with interrupt |
| Number of I/O Lines | 8 |
| Operating Voltage Range | 2.3 V to 5.5 V |
| Интерфейс | I2C/SMBus |
| Maximum Bus Frequency | 400 kHz |
| Configuration Registers | Present |
| Interrupt Output | Present |
| Weak Pull-Ups | Present |
| Корпус | 16-pin SSOP |
| Тип монтажа | Surface mount |
| Device Class | General-purpose remote I/O expander |
| Выходная конфигурация | Individually configurable input/output ports |
| Bus Signals | SCL and SDA |
Руководство по цоколевке PCA9554DB в корпусе 16-pin ssop
Цоколевка для PCA9554DB (корпус 16-pin ssop). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для PCA9554DB.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
PCA9554DB подходит для 7 применениеs: Microcontroller GPIO Expansion, Remote Sensor and Actuator Interface, Embedded Control Panel, Industrial Automation Module, Remote Monitoring and Control, LED and Indicator Control, Consumer and Communication Equipment.
Microcontroller GPIO Expansion
The PCA9554DB is useful when a microcontroller has too few direct pins for control and monitoring functions. Its eight configurable I/O ports operate through the I2C/SMBus interface at up to 400 kHz, allowing the host to read remote inputs and drive remote outputs while conserving package pins. The design should define port directions in the configuration registers and account for the device's interrupt output when an input change must wake the host.
Рекомендуется
Remote Sensor and Actuator Interface
PCA9554DB can place eight digital I/O lines behind an I2C connection between a controller and a remote circuit card. This arrangement is useful for reading discrete sensor outputs or driving relays, indicators, and other digital actuators when direct board-to-board GPIO routing is inconvenient. The 2.3 V to 5.5 V operating range supports mixed-voltage systems, but cable length, bus capacitance, pull-up values, grounding, and output drive must be validated for the selected remote load.
Рекомендуется
Embedded Control Panel
The eight ports can serve as an I2C-connected front panel interface for buttons, indicators, lamps, selectors, and status signals. A host microcontroller can scan inputs and update outputs over the same two-wire bus, reducing wiring compared with direct GPIO. The verified interrupt feature can reduce unnecessary polling when an input state changes, while the 400 kHz maximum bus rate supports compact embedded-control architectures when the total bus loading and firmware timing remain acceptable.
Рекомендуется
Industrial Automation Module
PCA9554DB is suitable for small automation modules that need a compact, addressable set of digital outputs and inputs. The device can connect discrete control signals to a microcontroller while the interrupt output provides an event path for changing input conditions. In an industrial enclosure, engineers should verify voltage tolerances, isolation requirements, surge protection, grounding, connector current limits, and the operating temperature range because those details are not provided in the supplied verified snippets.
Рекомендуется
Remote Monitoring and Control
The PCA9554DB can monitor remote digital conditions and return control outputs through the host's I2C bus. This pattern is useful in equipment where a central controller needs distributed status points without routing every signal back as a direct GPIO. The interrupt output can signal activity, but system timing depends on the host firmware, bus clock, pull-up network, and whether the remote signals are slower than the 400 kHz bus capability. Input thresholds and output current must be confirmed from the full datasheet.
Рекомендуется
LED and Indicator Control
Eight output ports from PCA9554DB can control groups of LEDs, status lamps, or indicator signals when the host lacks sufficient direct output pins. The I2C connection reduces the number of dedicated microcontroller pins, while configuration registers define which ports are outputs. The designer must check the device's output drive limits and supply requirements before directly loading LEDs or other devices; the supplied data confirms eight I/O lines and configurable ports but does not specify per-pin output current.
Рекомендуется
Consumer and Communication Equipment
PCA9554DB can add configurable digital lines in compact consumer, communications, or accessory hardware where the main controller is connected to I2C. Its 2.3 V to 5.5 V range accommodates common low-voltage and 5 V rails, and the 16-pin SSOP package supports compact board layouts. Product-specific compliance, temperature, EMC, and output-loading requirements are not supplied in the verified data and must be evaluated separately rather than inferred from the interface function.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PCA9554DB — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PCA9554A | TCA9554PWR | TCA9554ADBR | PCA9534DB |
|---|---|---|---|---|---|
| Brand | Texas Instruments | NXP Semiconductors | Texas Instruments | Texas Instruments | NXP Semiconductors |
| Package | 16-pin SSOP | 16-pin SSOP | TSSOP-16 | SSOP-16 | 16-pin SSOP |
| Interface | I2C/SMBus | I2C/SMBus | I2C/SMBus | I2C/SMBus | I2C/SMBus |
Ключевые отличия
- Eight configurable remote I/O lines in a compact 16-pin SSOP package (против PCA9554A)
- Explicit interrupt, configuration-register, and weak-pull-up features (против PCA9534DB)
- I2C/SMBus operation up to 400 kHz (против TCA9554PWR)
Заметки по проектированию
Place the PCA9554DB close to the SCL and SDA routing and keep the I2C traces short and continuous. The verified device supports up to 400 kHz, but actual bus operation also depends on capacitance, pull-up resistance, trace length, and every peripheral on the bus. Confirm the complete pin names and exposed connections from the manufacturer datasheet before finalizing the footprint.
Design the 2.3 V to 5.5 V supply rail with appropriate local decoupling and verify the host and peripheral logic levels. Do not infer output-current capability from the eight-port description; the verified snippets do not provide per-pin drive limits, so loads such as LEDs or relay drivers must be checked against the full manufacturer datasheet.
Do not treat PCA9554 and PCA9554A as address-identical. The supplied NXP listing states that the devices have different addresses, so replacing one with the other can leave the host controller unable to communicate. Firmware, pull-up configuration, interrupt polarity, and the selected manufacturer must all be reviewed together.
Reserve test points for VCC, ground, SCL, SDA, the interrupt line, and all eight I/O signals. Keeping these points accessible helps validate bus rise time, port direction, and interrupt behavior during bring-up. If a remote cable or long trace is used, evaluate signal integrity and protection separately from the nominal 400 kHz specification.
Информация о соответствии
The supplied verified snippets do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. No compliance claim should be inferred from the interface description.
