NXP Semiconductors

PCA9554U - 8-Bit I2C I/O Expander with Interrupt | NXP

Артикул: PCA9554U ✓ Активен
2.3 V to 5.5 V Vdss 16 pins Package 400 kHz Speed
MOQ: 1 |

PCA9554U Обзор

The NXP Semiconductors PCA9554U is an 8-bit CMOS I2C-bus and SMBus parallel I/O port with an interrupt output, supplied in a 16-pin SOIC package. It operates from 2.3 V to 5.5 V, supports I2C and SMBus communication up to 400 kHz, and adds eight configurable GPIO lines to a host processor through a two-wire serial interface. Its 16-pin package and low-voltage operation suit compact embedded, industrial, and consumer control systems.

An I2C I/O expander is an interface IC that increases the number of general-purpose input/output pins available to a microcontroller or other bus master. The PCA9554U belongs to the parallel I/O expander hierarchy, where an 8-bit port registers are connected to an I2C-controlled serial interface. This architecture preserves processor I/O resources while allowing switches, indicators, sensors, and other external circuitry to share a common bus.

The device includes an 8-bit configuration register, input register, output register, and polarity-inversion register. Each port pin can be configured independently as an input or output, and input polarity can be inverted for devices that generate active-low signals. Power-on defaults place all I/O pins in input mode with weak pull-ups. An active-low interrupt output provides a hardware indication that an input state has changed, reducing the need for continuous bus polling.

Three hardware address inputs, A0, A1, and A2, allow up to eight devices to share one I2C bus. This address arrangement makes the PCA9554U useful in systems that require several independent groups of GPIO. The fixed I2C address is programmed by the three address pins, while the serial interface provides read access to input-port data and write access to output and configuration registers. The NXP device is pin-to-pin and I2C-address compatible with the PCF8574 series, although enhanced register behavior requires corresponding firmware changes described in NXP Application Note AN469.

Typical uses include reading control buttons and selector switches, driving LED indicators, monitoring discrete alarm signals, and expanding interface lines for industrial controllers. The 2.3 V to 5.5 V operating range allows operation from common 3.3 V and 5 V rails. At 400 kHz, the interface is suitable for mainstream embedded control buses where throughput is sufficient for periodic status updates rather than continuous high-rate data streaming.

A practical design must keep the interrupt and I2C signal levels compatible with the host bus. Use pull-ups on SDA and SCL as required by the bus, connect the address pins to ground or VCC for the intended device address, and provide local decoupling near VCC. Review the I2C pull-up resistance against bus capacitance, speed, voltage, and the number of connected devices to avoid excessive rise times or signal-integrity problems.

This product page combines the manufacturer device information, package and pin information, drop-in replacement analysis, and practical implementation guidance. It also distinguishes the PCA9554U from address or package variants so engineers can confirm mechanical compatibility, register behavior, and required firmware changes before assigning a replacement to an existing PCB.

Аналоги без доработки для PCA9554U — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с PCA9554U (тот же форм-фактор и посадочное место) — отличается по Interrupt Output, Package, Device Type, Lifecycle Status.

NXP Semiconductors
Interrupt Output: /INT, open-drain
Package: 16-HVQFN (3x3 mm) with exposed pad
Сравнить с PCA9554U →
NXP Semiconductors
Interrupt Output: Yes
Package: 16-pin SSOP
Lifecycle Status: End of life
Сравнить с PCA9554U →
NXP Semiconductors
Package: SO16, 16 pins
Device Type: 8-bit I2C-bus/SMBus I/O expander with interrupt
Lifecycle Status: End of Life, according to the NXP product information search result
Сравнить с PCA9554U →

PCA9554ADB

✅ Прямая замена
NXP Semiconductors
📦 SOIC-16
8-bit I2C/SMBus I/O expander · 8 ports · 2.3 V to 5.5 V · 400 kHz maximum · I2C and SMBus · Yes · Yes · Yes

Уточнить цену

Открыть даташит →

PCA9554ABS3,118

✅ Прямая замена ⚠️ Характеристики не проверены
NXP Semiconductors
📦 SOIC-16
I2C, SMBus · 8 · 400 kHz · 2.3 V to 5.5 V · 5.5 V · 3 hardware address pins (up to 8 devices) · /INT, open-drain · 0x38 (3-bit addr 000 = 0x38)

Уточнить цену

Открыть даташит →

PCA9554U

✅ Прямая замена
NXP Semiconductors
📦 SOIC-16
8-bit I2C-bus and SMBus I/O port with interrupt · 8 pins · 3 inputs (A0, A1, A2) · 8 devices · 2.3 V to 5.5 V · I2C and SMBus · 400 kHz · CMOS

Уточнить цену

Открыть даташит →

PCA9554D

✅ Прямая замена ⚠️ Характеристики не проверены
NXP Semiconductors
📦 SOIC-16
8-bit I2C-bus/SMBus I/O expander with interrupt · 8 bits · I2C and SMBus · 400 kHz · SO16, 16 pins · CMOS · Serial I2C/SMBus interface for host communication · 8 configurable general-purpose I/O lines

Уточнить цену

Открыть даташит →

PCA9554U Характеристики

Device Type 8-bit I2C-bus and SMBus I/O port with interrupt
Number of I/O Pins 8 pins
Number of Address Inputs 3 inputs (A0, A1, A2)
Maximum Devices per Bus 8 devices
Operating Voltage Range 2.3 V to 5.5 V
Bus Interface I2C and SMBus
Maximum I2C Clock Frequency 400 kHz
Logic Technology CMOS
Register Count 4 registers (configuration, input, output, and polarity inversion)
Power-On I/O Configuration Inputs with weak pull-up
Interrupt Output 1 active-low interrupt output
Input Polarity Control Configurable active-high or active-low inversion
Package Pin Count 16 pins
Package Type 16-pin SOIC, surface mount
PCF8574 Compatibility Pin-to-pin and I2C-address compatible; software changes required
Application Note AN469

Конфигурация выводов PCA9554U

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
Контакт 1 A0 — I2C address input 0
Контакт 2 A1 — I2C address input 1
Контакт 3 A2 — I2C address input 2
Контакт 4 P0 — Port 0 input/output
Контакт 5 P1 — Port 1 input/output
Контакт 6 P2 — Port 2 input/output
Контакт 7 P3 — Port 3 input/output
Контакт 8 GND — Ground
Контакт 9 P4 — Port 4 input/output
Контакт 10 P5 — Port 5 input/output
Контакт 11 P6 — Port 6 input/output
Контакт 12 P7 — Port 7 input/output
Контакт 13 INT — Interrupt output
Контакт 14 VCC — Power supply
Контакт 15 SCL — Serial clock input
Контакт 16 SDA — Serial data input/output

Типичное применение

PCA9554U подходит для 6 применениеs: Industrial Control Panel I/O Expansion, LED and Relay Status Control, Alarm and Sensor Interface, Compact Consumer Control Interface, Server and Networking Control, Automotive Accessory Control.

🏭

Industrial Control Panel I/O Expansion

The PCA9554U is appropriate for adding switch, selector, and status inputs to an industrial controller without consuming its native GPIO pins. Its three address inputs permit as many as eight expanders to share an I2C bus, while the eight port bits can be individually configured as inputs or outputs. At a 400 kHz maximum bus rate, the device efficiently distributes periodic control and diagnostic information. The interrupt output can notify the controller when an input changes, avoiding continuous polling. Firmware should define the input, output, and polarity registers for each connected device and account for the different fixed addresses selected by A0, A1, and A2.

💡

LED and Relay Status Control

The PCA9554U can expand a microcontroller’s output capacity for LED indicators, relay-control signals, and digital status lamps. Each P0-P7 pin has independent input/output configuration and output-latch behavior, allowing the host to update groups of indicators through the I2C interface. Operating from 2.3 V to 5.5 V supports both 3.3 V and 5 V control systems. Designers should confirm that the output-pin voltage and current ratings satisfy the attached load; external drivers may be required for relays or high-current lamps. The weak input pull-ups are principally for startup and floating-input control and should not be treated as general-purpose output drive paths.

🧩

Alarm and Sensor Interface

The PCA9554U provides eight digital input channels for alarm lines, door sensors, limit switches, and other discrete sensors. Inputs can be read through the input-port register, and the polarity-inversion register allows active-low sensor outputs to be presented consistently to firmware. When an input changes, the interrupt output provides a hardware indication that the host can service before reading the port state. This event-driven approach reduces unnecessary bus traffic compared with continuous polling. The interrupt remains active while a change is pending, so the host should acknowledge or clear the condition through the appropriate register access and verify the polarity against the original schematic.

📱

Compact Consumer Control Interface

In a compact consumer product, the PCA9554U can centralize button, mode-select, and indicator I/O while keeping the main application processor free for display, communications, or processing tasks. The 16-pin SOIC package supports conventional surface-mount assembly, and the 2.3 V minimum supply voltage permits use with low-voltage system rails. Because the device starts with all ports configured as inputs and weak pull-ups, external switch networks receive defined behavior during reset. Firmware should reconfigure outputs only after the system has completed initialization, and the SDA and SCL pull-up network should be calculated from bus capacitance and operating voltage to preserve reliable communication at the intended clock rate.

🖥️

Server and Networking Control

The PCA9554U can add low-speed control and status lines to server, storage, or networking equipment where the main controller has limited available GPIO. Typical functions include module-present detection, reset requests, fault indicators, and front-panel status inputs. The I2C interface allows these signals to share a bus with other compatible peripherals, while A0, A1, and A2 provide flexible address assignment. The interrupt line is useful when a change must be handled promptly without continuously reading the port. For equipment with strict power-sequence or fault-response requirements, validate the default input state and debounce external mechanical contacts so an initialization or vibration event does not create unintended control actions.

🚗

Automotive Accessory Control

The PCA9554U can serve as a general-purpose auxiliary I/O controller in non-safety-critical automotive accessory systems, subject to the manufacturer’s qualification and application requirements. It is useful for adding discrete body, climate, or convenience-control signals to a bus-based controller. The 8-bit port, three address inputs, and interrupt output provide a compact way to manage multiple signals while the I2C interface carries commands and status. Designers must verify the applicable automotive temperature range, AEC-Q100 status, ESD requirements, and transient protection for each connected line before production use. Do not use this part for safety-critical actuation without the required system-level qualification and diagnostic coverage.

Where can I download the PCA9554U datasheet PDF?
The PCA9554U datasheet and product information are available from the NXP Semiconductors product page for PCA9554U. The manufacturer documentation covers the 8-bit I/O ports, configuration and polarity registers, electrical characteristics, package details, and application information. Use the manufacturer datasheet as the authority for final pin assignments, timing limits, power recommendations, and device operating conditions.
What is the PCA9554U and what does it do?
The PCA9554U is an 8-bit CMOS I2C-bus and SMBus parallel I/O port with an interrupt output. It adds eight configurable GPIO lines to a host controller through a two-wire interface. According to the NXP device description, each port supports input, output, and polarity-inversion functions, while the interrupt output signals a change in input-port data.
What are the key specifications of PCA9554U that engineers should know?
The PCA9554U provides 8 GPIO pins, a 2.3 V to 5.5 V operating range, and I2C/SMBus operation up to 400 kHz. Its four registers independently control configuration, input data, output data, and input polarity. Three address pins allow as many as eight devices to share a bus, and all ports default to inputs with weak pull-ups after power-on.
What is the PCA9554U pinout?
The 16-pin PCA9554U assigns pins 1 through 3 to A0, A1, and A2; pins 4 through 7 to P0 through P3; pin 8 to GND; pins 9 through 12 to P4 through P7; pin 13 to INT; pin 14 to VCC; pin 15 to SCL; and pin 16 to SDA. Use the manufacturer pin-description table when assigning PCB tracks and test points.
Can the PCA9554U replace a PCF8574?
The PCA9554U is pin-to-pin and I2C-address compatible with the PCF8574 series, but its enhanced register organization requires firmware changes. NXP discusses these software differences in Application Note AN469. Verify the original device address, register map, interrupt behavior, and existing driver before treating the replacement as functionally equivalent.
Is PCA9554U suitable for a 3.3 V embedded system?
Yes, the PCA9554U supports a 2.3 V to 5.5 V operating range, which includes a 3.3 V rail. The I2C pull-ups must also be connected to a voltage compatible with the host and PCA9554U levels. If the bus includes 5 V devices, use a translator or level shifter rather than allowing pull-ups to raise the bus above the host's safe voltage.
How do I set the I2C address of the PCA9554U?
The PCA9554U address is selected with the A0, A1, and A2 hardware pins. Each address input can be tied to ground or VCC, allowing up to eight devices with different combinations on one I2C bus. NXP confirms that three hardware pins are used to program and vary the fixed I2C address, allowing multiple devices to share the same bus.
What is the best drop-in replacement for PCA9554U?
PCA9554U is an SOIC-16 device, so a replacement must use the same 16-pin footprint and preserve the A0, A1, A2, P0-P7, INT, VCC, SCL, and SDA connections. Address-compatible alternatives can generally be installed without changing the PCB, but the I2C address and polarity or register behavior must still be checked. PCA9554AD and compatible SOIC-16 variants require address-specific review.
Can PCA9554AD replace PCA9554U without changing the PCB?
PCA9554AD can use the same SOIC-16 footprint and shares the core 8-bit I2C I/O-expander function, so it is a PCB-level drop-in candidate. Its key difference is the fixed I2C address: NXP identifies PCA9554AD as having a different address from PCA9554. Firmware must therefore select the new address, and an in-system interrupt may still affect the previously assigned device address.
Is there a TI equivalent for the NXP PCA9554U?
The TI PCA9554 family provides the same basic function: an 8-bit, 2.3 V to 5.5 V I2C/SMBus I/O expander with interrupt, weak pull-ups, and configuration registers. A compatible SOIC-16 ordering must still be selected, and the address, polarity handling, and register behavior should be checked against the original firmware. TI Application Note material also identifies PCF8574 compatibility considerations.
When should I choose PCA9554U instead of a PCF8574?
Choose the PCA9554U when the design benefits from separate configuration, input, output, and polarity-inversion registers, an interrupt output, and three configurable address inputs. It can also host up to eight devices on one I2C bus. A PCF8574 may suit an existing driver that already matches its simpler register arrangement, but migration requires software review for the PCA9554U enhancements.
Where can I buy PCA9554U online?
Use the Request a Quote form on this page to request current PCA9554U availability, lot allocation, and order handling. The form is the appropriate channel for quote-based or changing inventory conditions and can help identify the required package and suffix configuration before an order is placed.
What is the price of PCA9554U?
Current PCA9554U pricing is best requested through the Request a Quote form on this page. Quote responses can reflect the exact ordering code, volume, delivery date, and current component availability. No static unit-price figure should be used for budgeting because market and inventory conditions can change.
What is the lead time and stock status for PCA9554U?
Current stock, lead time, minimum order quantity, and production allocation should be confirmed through the Request a Quote form on this page. Because availability may vary by package suffix and manufacturing lot, provide the complete intended ordering code and required quantity when requesting a quotation.
What can replace PCA9554U?
PCA9554AD is a same-manufacturer SOIC-16 alternative with a different fixed I2C address, while compatible PCA9554-family devices from another manufacturer may provide the same 8-bit expander function. A true drop-in choice must preserve the 16-pin footprint, address configuration, voltage range, bus speed, interrupt polarity, and register expectations. Review firmware before substitution.

Справочные инженерные данные для PCA9554U — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose PCA9554U when an embedded controller needs eight additional GPIO lines, configurable input polarity, and an interrupt output over an I2C or SMBus bus. Its 2.3 V to 5.5 V range, 400 kHz bus support, and three address inputs make it appropriate for industrial panels, control modules, server accessories, and compact consumer equipment. Select PCA9554AD or PCA9554A only when their different fixed addresses can be accepted without disrupting other bus devices; firmware and interrupt ownership must be revised accordingly. A Texas Instruments PCA9554 variant may be useful for supply-chain flexibility, but the address, driver, and register map must be checked before substitution. PCF8574 is a mechanically compatible alternative for designs with an existing PCF8574 driver, while PCA9554U is preferable when independent polarity inversion and a more structured register interface are important.

Сравнение с аналогами

Параметр Этот товар PCA9554AD PCA9554A PCA9554U PCA9554D
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors Texas Instruments Texas Instruments
Package SOIC-16 SOIC-16 - same SOIC-16 - same SOIC-16 - same SOIC-16 - same
I/O Port Width 8 bits 8 bits 8 bits 8 bits 8 bits
Interface I2C and SMBus I2C and SMBus I2C and SMBus I2C and SMBus I2C and SMBus
Address Inputs 3 hardware inputs (A0, A1, A2) 3 hardware inputs 3 hardware inputs 3 hardware inputs 3 hardware inputs
Fixed I2C Address 0x20 with A2-A0 low Different address; address difference is 0x18 hexadecimal Different address; address difference is 0x18 hexadecimal 0x40 with A2-A0 low; difference is 0x20 hexadecimal 0x40 with A2-A0 low; difference is 0x20 hexadecimal
Interrupt Output Yes Yes Yes Yes Yes
Power-On Port State Inputs with weak pull-up Inputs with weak pull-up Inputs with weak pull-up Inputs with weak pull-up Inputs with weak pull-up

Ключевые отличия

  • Supports eight independent configurable GPIO lines with dedicated polarity control (против PCF8574)
  • Provides hardware address selection for multi-expander buses (против PCA9554 with a fixed address configuration)
  • Combines 8-bit parallel I/O with an interrupt output (против A microcontroller GPIO bank without an expander)
  • Supports common 3.3 V and 5 V system rails (против PCA9554AD with a different fixed address)

Заметки по проектированию

Route SDA and SCL as a compact two-wire bus and place the associated pull-up resistors near the master device or at the location recommended by the system bus design. Keep the PCA9554U address-pin traces short and assign A0, A1, and A2 only after checking the complete device address map. Place the local supply capacitor close to pin 14 and provide a direct ground return from pin 8.

Select I2C pull-up resistance using the bus voltage, total capacitance, target clock rate, sink-current capability of every connected device, and required rise time. A pull-up that is too strong increases low-level current, while one that is too weak produces slow rising edges and intermittent communication. Verify timing with the worst-case bus capacitance and all devices powered simultaneously.

Do not assume a different fixed-address variant is interchangeable in software. After changing from PCA9554U to PCA9554AD, PCA9554A, or another manufacturer's PCA9554U, update the bus address, verify the intended device responds to the correct address, and check for an unexpected interrupt from the changed address. NXP Application Note AN469 addresses the software changes associated with PCF8574-to-PCA9554 migration.

Decouple VCC locally and confirm that all eight outputs remain within their specified voltage and current limits. Weak pull-ups are intended primarily to define the default input state and are not substitutes for output drivers or high-current sink paths. Use an appropriate transistor or driver when an attached relay, lamp, or other load exceeds the port's specified capability.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

Compliance status is not stated in the device information. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations against the exact ordering code and current manufacturer documentation before production release.

Данные проверены: 2026-11-14 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

pca9554 datasheet PCA9554U datasheet PCA9554U datasheet pdf PCA9554U pinout PCA9554U pinout SOIC-16 PCA9554U equivalent PCA9554U replacement PCA9554U cross reference PCA9554U vs PCA9554AD PCA9554U application circuit NXP PCA9554U PCA9554U I2C address PCA9554U 400 kHz PCA9554U price PCA9554U stock

Связанные компоненты & термины

NXP Semiconductors PCA9554U Texas Instruments PCA9554AD PCA9554A PCA9554D PCF8574 I2C I/O expander SMBus I/O port parallel I/O expander interface IC GPIO semiconductor CMOS 2.3 V to 5.5 V 400 kHz I2C SOIC-16 SOIC package family surface mount SMD weak pull-up polarity inversion A0 A1 A2 address inputs active-low interrupt AN469
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ