PCA9554U - 8-Bit I2C I/O Expander with Interrupt | NXP
MPN: PCA9554U ✓ فعالPCA9554U نمای کلی
An I2C I/O expander is an interface IC that increases the number of general-purpose input/output pins available to a microcontroller or other bus master. The PCA9554U belongs to the parallel I/O expander hierarchy, where an 8-bit port registers are connected to an I2C-controlled serial interface. This architecture preserves processor I/O resources while allowing switches, indicators, sensors, and other external circuitry to share a common bus.
The device includes an 8-bit configuration register, input register, output register, and polarity-inversion register. Each port pin can be configured independently as an input or output, and input polarity can be inverted for devices that generate active-low signals. Power-on defaults place all I/O pins in input mode with weak pull-ups. An active-low interrupt output provides a hardware indication that an input state has changed, reducing the need for continuous bus polling.
Three hardware address inputs, A0, A1, and A2, allow up to eight devices to share one I2C bus. This address arrangement makes the PCA9554U useful in systems that require several independent groups of GPIO. The fixed I2C address is programmed by the three address pins, while the serial interface provides read access to input-port data and write access to output and configuration registers. The NXP device is pin-to-pin and I2C-address compatible with the PCF8574 series, although enhanced register behavior requires corresponding firmware changes described in NXP Application Note AN469.
Typical uses include reading control buttons and selector switches, driving LED indicators, monitoring discrete alarm signals, and expanding interface lines for industrial controllers. The 2.3 V to 5.5 V operating range allows operation from common 3.3 V and 5 V rails. At 400 kHz, the interface is suitable for mainstream embedded control buses where throughput is sufficient for periodic status updates rather than continuous high-rate data streaming.
A practical design must keep the interrupt and I2C signal levels compatible with the host bus. Use pull-ups on SDA and SCL as required by the bus, connect the address pins to ground or VCC for the intended device address, and provide local decoupling near VCC. Review the I2C pull-up resistance against bus capacitance, speed, voltage, and the number of connected devices to avoid excessive rise times or signal-integrity problems.
This product page combines the manufacturer device information, package and pin information, drop-in replacement analysis, and practical implementation guidance. It also distinguishes the PCA9554U from address or package variants so engineers can confirm mechanical compatibility, register behavior, and required firmware changes before assigning a replacement to an existing PCB.
جایگزینهای drop-in برای PCA9554U — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای PCA9554U (همان فرمفاکتور و فوتپرینت) — متفاوت در Interrupt Output, Package, Device Type, Lifecycle Status.
PCA9554ADB
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PCA9554ABS3,118
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PCA9554U
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PCA9554D
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PCA9554U مشخصات
| Device Type | 8-bit I2C-bus and SMBus I/O port with interrupt |
| Number of I/O Pins | 8 pins |
| Number of Address Inputs | 3 inputs (A0, A1, A2) |
| Maximum Devices per Bus | 8 devices |
| Operating Voltage Range | 2.3 V to 5.5 V |
| Bus Interface | I2C and SMBus |
| Maximum I2C Clock Frequency | 400 kHz |
| Logic Technology | CMOS |
| Register Count | 4 registers (configuration, input, output, and polarity inversion) |
| Power-On I/O Configuration | Inputs with weak pull-up |
| Interrupt Output | 1 active-low interrupt output |
| Input Polarity Control | Configurable active-high or active-low inversion |
| Package Pin Count | 16 pins |
| Package Type | 16-pin SOIC, surface mount |
| PCF8574 Compatibility | Pin-to-pin and I2C-address compatible; software changes required |
| Application Note | AN469 |
پیکربندی پین PCA9554U
| پین 1 | A0 — I2C address input 0 |
| پین 2 | A1 — I2C address input 1 |
| پین 3 | A2 — I2C address input 2 |
| پین 4 | P0 — Port 0 input/output |
| پین 5 | P1 — Port 1 input/output |
| پین 6 | P2 — Port 2 input/output |
| پین 7 | P3 — Port 3 input/output |
| پین 8 | GND — Ground |
| پین 9 | P4 — Port 4 input/output |
| پین 10 | P5 — Port 5 input/output |
| پین 11 | P6 — Port 6 input/output |
| پین 12 | P7 — Port 7 input/output |
| پین 13 | INT — Interrupt output |
| پین 14 | VCC — Power supply |
| پین 15 | SCL — Serial clock input |
| پین 16 | SDA — Serial data input/output |
کاربردهای معمول
PCA9554U مناسب است برای 6 کاربردs: Industrial Control Panel I/O Expansion, LED and Relay Status Control, Alarm and Sensor Interface, Compact Consumer Control Interface, Server and Networking Control, Automotive Accessory Control.
Industrial Control Panel I/O Expansion
The PCA9554U is appropriate for adding switch, selector, and status inputs to an industrial controller without consuming its native GPIO pins. Its three address inputs permit as many as eight expanders to share an I2C bus, while the eight port bits can be individually configured as inputs or outputs. At a 400 kHz maximum bus rate, the device efficiently distributes periodic control and diagnostic information. The interrupt output can notify the controller when an input changes, avoiding continuous polling. Firmware should define the input, output, and polarity registers for each connected device and account for the different fixed addresses selected by A0, A1, and A2.
LED and Relay Status Control
The PCA9554U can expand a microcontroller’s output capacity for LED indicators, relay-control signals, and digital status lamps. Each P0-P7 pin has independent input/output configuration and output-latch behavior, allowing the host to update groups of indicators through the I2C interface. Operating from 2.3 V to 5.5 V supports both 3.3 V and 5 V control systems. Designers should confirm that the output-pin voltage and current ratings satisfy the attached load; external drivers may be required for relays or high-current lamps. The weak input pull-ups are principally for startup and floating-input control and should not be treated as general-purpose output drive paths.
Alarm and Sensor Interface
The PCA9554U provides eight digital input channels for alarm lines, door sensors, limit switches, and other discrete sensors. Inputs can be read through the input-port register, and the polarity-inversion register allows active-low sensor outputs to be presented consistently to firmware. When an input changes, the interrupt output provides a hardware indication that the host can service before reading the port state. This event-driven approach reduces unnecessary bus traffic compared with continuous polling. The interrupt remains active while a change is pending, so the host should acknowledge or clear the condition through the appropriate register access and verify the polarity against the original schematic.
Compact Consumer Control Interface
In a compact consumer product, the PCA9554U can centralize button, mode-select, and indicator I/O while keeping the main application processor free for display, communications, or processing tasks. The 16-pin SOIC package supports conventional surface-mount assembly, and the 2.3 V minimum supply voltage permits use with low-voltage system rails. Because the device starts with all ports configured as inputs and weak pull-ups, external switch networks receive defined behavior during reset. Firmware should reconfigure outputs only after the system has completed initialization, and the SDA and SCL pull-up network should be calculated from bus capacitance and operating voltage to preserve reliable communication at the intended clock rate.
Server and Networking Control
The PCA9554U can add low-speed control and status lines to server, storage, or networking equipment where the main controller has limited available GPIO. Typical functions include module-present detection, reset requests, fault indicators, and front-panel status inputs. The I2C interface allows these signals to share a bus with other compatible peripherals, while A0, A1, and A2 provide flexible address assignment. The interrupt line is useful when a change must be handled promptly without continuously reading the port. For equipment with strict power-sequence or fault-response requirements, validate the default input state and debounce external mechanical contacts so an initialization or vibration event does not create unintended control actions.
Automotive Accessory Control
The PCA9554U can serve as a general-purpose auxiliary I/O controller in non-safety-critical automotive accessory systems, subject to the manufacturer’s qualification and application requirements. It is useful for adding discrete body, climate, or convenience-control signals to a bus-based controller. The 8-bit port, three address inputs, and interrupt output provide a compact way to manage multiple signals while the I2C interface carries commands and status. Designers must verify the applicable automotive temperature range, AEC-Q100 status, ESD requirements, and transient protection for each connected line before production use. Do not use this part for safety-critical actuation without the required system-level qualification and diagnostic coverage.
دادههای مرجع مهندسی برای PCA9554U — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | PCA9554AD | PCA9554A | PCA9554U | PCA9554D |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | Texas Instruments | Texas Instruments |
| Package | SOIC-16 | SOIC-16 - same | SOIC-16 - same | SOIC-16 - same | SOIC-16 - same |
| I/O Port Width | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits |
| Interface | I2C and SMBus | I2C and SMBus | I2C and SMBus | I2C and SMBus | I2C and SMBus |
| Address Inputs | 3 hardware inputs (A0, A1, A2) | 3 hardware inputs | 3 hardware inputs | 3 hardware inputs | 3 hardware inputs |
| Fixed I2C Address | 0x20 with A2-A0 low | Different address; address difference is 0x18 hexadecimal | Different address; address difference is 0x18 hexadecimal | 0x40 with A2-A0 low; difference is 0x20 hexadecimal | 0x40 with A2-A0 low; difference is 0x20 hexadecimal |
| Interrupt Output | Yes | Yes | Yes | Yes | Yes |
| Power-On Port State | Inputs with weak pull-up | Inputs with weak pull-up | Inputs with weak pull-up | Inputs with weak pull-up | Inputs with weak pull-up |
تفاوتهای کلیدی
- Supports eight independent configurable GPIO lines with dedicated polarity control (در مقابلPCF8574)
- Provides hardware address selection for multi-expander buses (در مقابلPCA9554 with a fixed address configuration)
- Combines 8-bit parallel I/O with an interrupt output (در مقابلA microcontroller GPIO bank without an expander)
- Supports common 3.3 V and 5 V system rails (در مقابلPCA9554AD with a different fixed address)
یادداشتهای طراحی
Route SDA and SCL as a compact two-wire bus and place the associated pull-up resistors near the master device or at the location recommended by the system bus design. Keep the PCA9554U address-pin traces short and assign A0, A1, and A2 only after checking the complete device address map. Place the local supply capacitor close to pin 14 and provide a direct ground return from pin 8.
Select I2C pull-up resistance using the bus voltage, total capacitance, target clock rate, sink-current capability of every connected device, and required rise time. A pull-up that is too strong increases low-level current, while one that is too weak produces slow rising edges and intermittent communication. Verify timing with the worst-case bus capacitance and all devices powered simultaneously.
Do not assume a different fixed-address variant is interchangeable in software. After changing from PCA9554U to PCA9554AD, PCA9554A, or another manufacturer's PCA9554U, update the bus address, verify the intended device responds to the correct address, and check for an unexpected interrupt from the changed address. NXP Application Note AN469 addresses the software changes associated with PCF8574-to-PCA9554 migration.
Decouple VCC locally and confirm that all eight outputs remain within their specified voltage and current limits. Weak pull-ups are intended primarily to define the default input state and are not substitutes for output drivers or high-current sink paths. Use an appropriate transistor or driver when an attached relay, lamp, or other load exceeds the port's specified capability.
اطلاعات انطباق
Compliance status is not stated in the device information. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations against the exact ordering code and current manufacturer documentation before production release.