PIC16C62A-20/SS - 8-bit CMOS MCU, 3.5KB OTP, 20MHz | Microchip
Артикул: PIC16C62A-20/SS ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.95 | $6,95 |
| 10 | $6.18 | $61,80 |
| 100 | $5.42 | $542,00 |
| 500 | $4.78 | $2.390,00 |
| 1.000 | $4.25 | $4.250,00 |
PIC16C62A-20/SS Обзор
An 8-bit microcontroller is a small, single-chip computer built around an 8-bit data bus and a RISC (Reduced Instruction Set Computer) core optimized for deterministic, low-latency embedded control. The PIC16Cxx family falls within the hierarchy of microcontroller -> embedded controller -> semiconductor IC, and historically targets cost-sensitive, low-power, deterministic control tasks in industrial, automotive, and consumer applications. OTP EPROM program memory allows one-time field programming via a standard EPROM programmer, which simplifies production and reduces unit cost versus flash devices.
Key features include a fully static design (allowing the clock to be stopped for power-saving idle modes), a wide operating voltage range of 2.5V to 6.0V (per family datasheet), industrial-grade (-40C to +85C) temperature operation for this /SS variant, low-power consumption of 15 µA typical at 5V/4 MHz, and 1 µA typical at 3V/32 kHz. Connectivity is supported through I²C and SPI serial peripherals, and the device is pin-and-code compatible with related PIC16C62 and PIC16C6x family members.
Architecturally, the PIC16C62A uses a 14-bit instruction word with a Harvard bus architecture, separating program and data memory paths for simultaneous fetch and execute. The 20 MHz oscillator yields a 200 ns instruction cycle, and the 22 I/O pins can be configured individually for digital input or output. The chip's peripheral set (PWM, WDT, POR, Brown-out Reset) makes it suitable for motor control, sensor reading, and supervisory loops without external support ICs.
Typical applications include industrial control logic, motor drive interface, sensor signal conditioning, LED driver sequencing, white-goods appliance control, and hobby/educational embedded platforms. It is also used as a drop-in replacement where PIC16C55, PIC16C57, or PIC16C62 OTP-programmed parts are specified.
When designing with this OTP device, ensure the final firmware is fully validated before programming because OTP parts cannot be re-programmed. Add a decoupling capacitor of 0.1 µF close to VDD, and follow Microchip's PICmicro Mid-Range Reference Manual for oscillator and reset configuration. This page synthesizes distributor pricing, cross-reference alternatives, and practical design notes not consolidated in the manufacturer datasheet.
Аналоги без доработки для PIC16C62A-20/SS — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC16C62A-20/SS (тот же форм-фактор и посадочное место) — отличается по Program Memory Type, Program Memory Size, Instruction Set, Operating Temperature Range, Package.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC16C62A-20E/SS
✅ Прямая замена✓ В наличии
$5.65 / шт.
Открыть даташит →PIC16C62A-20I/SS
✅ Прямая замена✓ В наличии
$1.8 / шт.
Открыть даташит →PIC16C62A-10/SS
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
PIC16C62A-04/SS
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$2.84 / шт.
Открыть даташит →PIC16C62B-20/SS
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$4.55 / шт.
Открыть даташит →PIC16C622-20/SS
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$1.38 / шт.
Открыть даташит →PIC16C62A-20/SS Максимальные параметры и электрические характеристики
| Core Processor | PIC |
| Core Size | 8-Bit |
| Series | PIC® 16C |
| Program Memory Size | 3.5 KB (2K × 14) OTP EPROM |
| RAM Size | 128 × 8 bytes |
| Number of I/O Pins | 22 |
| Speed (Clock Frequency) | 20 MHz |
| Напряжение питания | 2.5 V to 6.0 V (5 V typical) |
| Connectivity | I²C, SPI |
| Peripherals | Brown-out Detect/Reset, POR, PWM, WDT |
| Oscillator Type | External |
| Корпус / Типоразмер | 28-SSOP (0.209", 5.30 mm Width) |
| Тип монтажа | Surface Mount |
| Рабочая температура | 0C to +70C (Commercial) |
| Instruction Set | 14-bit RISC (Mid-Range) |
| Packaging | Tube |
Конфигурация выводов PIC16C62A-20/SS
| Контакт 1 | RA2/AN2 — Port A bit 2 / Analog input 2 |
| Контакт 2 | RA3/AN3 — Port A bit 3 / Analog input 3 |
| Контакт 3 | RA4/T0CKI — Port A bit 4 / Timer 0 clock input |
| Контакт 4 | RA5/SS/AN4 — Port A bit 5 / SPI Slave Select / Analog input 4 |
| Контакт 5 | VSS — Ground |
| Контакт 6 | RB0/INT — Port B bit 0 / External interrupt |
| Контакт 7 | RB1 — Port B bit 1 |
| Контакт 8 | RB2 — Port B bit 2 |
| Контакт 9 | RB3 — Port B bit 3 |
| Контакт 10 | RB4 — Port B bit 4 |
| Контакт 11 | RB5 — Port B bit 5 |
| Контакт 12 | RB6 — Port B bit 6 |
| Контакт 13 | RB7 — Port B bit 7 |
| Контакт 14 | VSS — Ground |
| Контакт 15 | RC0 — Port C bit 0 |
| Контакт 16 | RC1 — Port C bit 1 |
| Контакт 17 | RC2/CCP1 — Port C bit 2 / CCP1 PWM output |
| Контакт 18 | RC3 — Port C bit 3 |
| Контакт 19 | RC4 — Port C bit 4 |
| Контакт 20 | RC5 — Port C bit 5 |
| Контакт 21 | RC6 — Port C bit 6 |
| Контакт 22 | RC7 — Port C bit 7 |
| Контакт 23 | VDD — Positive supply voltage |
| Контакт 24 | VDD — Positive supply voltage |
| Контакт 25 | OSC2/CLKOUT — Oscillator crystal output / Clock out |
| Контакт 26 | OSC1/CLKIN — Oscillator crystal input / External clock in |
| Контакт 27 | MCLR/VPP — Master clear reset / Programming voltage |
| Контакт 28 | RA0/AN0 — Port A bit 0 / Analog input 0 |
Типичное применение
PIC16C62A-20/SS подходит для 6 применениеs: Industrial Control Logic, Motor Drive Interface, Sensor Signal Conditioning, LED Driver Sequencing, White-Goods Appliance Control, Hobby and Educational Embedded Platforms.
Industrial Control Logic
The PIC16C62A-20/SS fits industrial control logic boards because its 22 I/O pins drive relays, switches, and indicator LEDs without external I/O expanders, and the 20 MHz core handles 200 ns instruction cycles for fast deterministic control loops. The integrated Brown-out Detect/Reset and Power-on Reset ensure reliable startup in noisy 24V-derived 5V industrial rails. OTP EPROM program memory keeps unit cost low for high-volume machine control boards once firmware is finalized, making it ideal for programmable logic controllers, conveyor controllers, and sensor interface boards where price dominates over re-programmability.
Рекомендуется
Motor Drive Interface
The PIC16C62A-20/SS suits motor drive interface boards because its PWM peripheral generates variable-duty drive signals for DC motor speed control, and its 22 I/O pins can read encoders, limit switches, and current-sense signals. The 20 MHz clock provides tight control loop timing, while OTP EPROM ensures the firmware cannot be accidentally overwritten by voltage transients common on motor power buses. The SSOP-28 surface-mount package fits compact BLDC driver boards, and the wide 2.5V-6.0V supply range accepts standard 5V motor logic rails without regulation. Designers should add flyback diodes on all PWM outputs to protect against inductive kickback.
Рекомендуется
Sensor Signal Conditioning
The PIC16C62A-20/SS is well-suited to sensor signal conditioning boards where the MCU reads analog or digital sensors, applies calibration, and outputs formatted data via I²C or SPI. The integrated I²C and SPI peripherals directly interface with temperature sensors, accelerometers, and EEPROMs, while the 22 I/O pins handle discrete sensor flags and status LEDs. OTP EPROM program memory provides tamper-resistance for calibrated production units, and the 128-byte RAM is sufficient for small sensor data buffers. Use the Watchdog Timer to recover from sensor bus lockups in unattended field deployments.
Рекомендуется
LED Driver Sequencing
The PIC16C62A-20/SS fits LED driver sequencing applications because its PWM outputs drive multiple LED channels at varying brightness levels and its 20 MHz clock supports complex chase and fade patterns. The 22 I/O pins can individually control status LED arrays, RGB channels, and seven-segment displays without external driver ICs. The low-power 15 µA typical current at 5V/4 MHz keeps idle sequencer power low, and the SSOP-28 footprint is small enough for compact signage controller PCBs. OTP memory locks the final lighting pattern against accidental field reprogramming.
Рекомендуется
White-Goods Appliance Control
The PIC16C62A-20/SS is appropriate for white-goods appliance control boards including washing machines, dishwashers, and microwave oven interfaces. Its integrated Brown-out Detect handles power dips during motor inrush, and the Watchdog Timer recovers from firmware lockups in harsh electrical environments. The 22 I/O pins drive seven-segment displays, keypad matrices, and relay control outputs, while PWM modulates motor speed or heater elements. OTP EPROM keeps per-unit cost low for high-volume appliance production runs, and the wide 2.5V-6.0V supply tolerance accepts unregulated rectified mains-derived rails.
Рекомендуется
Hobby and Educational Embedded Platforms
The PIC16C62A-20/SS is a classic educational microcontroller used in PIC training kits, university embedded systems courses, and DIY hobby projects. Its 14-bit mid-range instruction set is well-documented in the Microchip PICmicro Mid-Range Reference Manual, and the 28-pin SSOP package is easy to breadboard with breakout adapters. The 20 MHz clock, 22 I/O pins, and I²C/SPI peripherals cover the full range of beginner projects from LED blinking to sensor interfacing and serial communications. OTP EPROM makes it ideal for take-home student projects where final code must be locked.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC16C62A-20/SS — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC16C62A-20E/SS | PIC16C62A-20I/SS | PIC16C62A-10/SS | PIC16C62A-04/SS |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SSOP | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same |
| Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 10 MHz | 4 MHz |
| Program Memory | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP |
| Operating Temperature | 0C to +70C (Commercial) | -40C to +125C (Extended) | -40C to +85C (Industrial) | 0C to +70C (Commercial) | 0C to +70C (Commercial) |
| RAM Size | 128 bytes | 128 bytes | 128 bytes | 128 bytes | 128 bytes |
| I/O Pins | 22 | 22 | 22 | 22 | 22 |
| Connectivity | I²C, SPI | I²C, SPI | I²C, SPI | I²C, SPI | I²C, SPI |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
Ключевые отличия
- Same silicon, broader temperature range for industrial use (против PIC16C62A-20E/SS)
- Two times the clock speed versus lower-frequency family variants (против PIC16C62A-10/SS)
- Pin-compatible with the broader PIC16C62x family (против PIC16C622-20/SS)
Заметки по проектированию
Add a 0.1 µF ceramic decoupling capacitor as close as possible to the VDD pin (pin 23/24 on the SSOP-28) and a bulk 10 µF tantalum or electrolytic capacitor on the supply rail. The PIC16C62A draws 15 µA typical at 5V/4 MHz and 1 µA typical at 3V/32 kHz per the family datasheet; ensure the supply can deliver peak current during ADC and I/O switching without sagging.
Because this is an OTP (One-Time-Programmable) EPROM device, the firmware cannot be erased or re-programmed once written. Always validate the firmware on a windowed or flash-equivalent development part (e.g., PIC16F62x family) before committing to OTP programming. EPROM programming requires the MCLR/VPP pin to be raised to VPP (~13V) - verify your programmer supports the PIC16C62A OTP algorithm.
Place the external oscillator crystal or resonator within 1 cm of the OSC1/OSC2 pins (pins 25/26) and route the oscillator traces symmetrically with a ground guard ring to reduce EMI coupling. Keep high-current PWM traces (CCP1 on RC2) short and away from analog sensor inputs on RA0-RA5 to minimize digital switching noise injection into ADC conversions.
Estimated: At 20 MHz and 5V supply, the PIC16C62A-20/SS typical core current is approximately 5-10 mA. With VDD = 5V, estimated power dissipation is 25-50 mW - well within the SSOP-28 thermal limits without a heatsink, even at the upper commercial temperature range. No thermal management is required for typical embedded applications.
Информация о соответствии
Lifecycle is obsolete per Microchip product status; original OTP EPROM parts predate modern RoHS/REACH compliance disclosures. Compliance status not confirmed in available data - request a certificate of compliance from the distributor when ordering legacy stock.
