PIC16C63A-20/SS - 8-Bit 20MHz OTP MCU 7KB | Microchip
Артикул: PIC16C63A-20/SS ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.95 | $4,95 |
| 10 | $4.45 | $44,50 |
| 100 | $3.96 | $396,00 |
| 500 | $3.56 | $1.780,00 |
| 1.000 | $3.17 | $3.170,00 |
PIC16C63A-20/SS Обзор
A mid-range PIC microcontroller is a class of 8-bit RISC processor that balances code density, peripheral integration, and cost, sitting between baseline PIC10/12/16 devices and the higher-performance PIC18 family. These MCUs use a 14-bit instruction word and Harvard bus topology, allowing simultaneous instruction fetch and data access. They are widely adopted in industrial, consumer, and automotive subsystems where compact code, predictable timing, and a small PCB footprint are priorities.
Key features include a wide operating voltage range from 2.5 V to 6.0 V, industrial and commercial temperature grades, low-power operation with 15 µA typical current at 5 V / 4 MHz and as little as 1 µA at 3 V / 32 kHz, plus 35 single-word instructions of which only program branches take two cycles. The PIC16C63A integrates dual analog comparators, a USART, and a synchronous serial port (SSP) supporting SPI and I2C master/slave modes, enabling direct connectivity to sensors, EEPROMs, displays, and other microcontrollers without external glue logic.
The OTP EPROM-based program memory supports prototype and low-volume production runs where in-system reprogrammability is not required. Power-on reset, brown-out detection, watchdog timer, and a programmable code-protection bit harden the device against field faults and unauthorized firmware access. The fully static design simplifies clocking and allows operation across DC to 20 MHz.
Typical applications include industrial control panels, motor drive front-ends, sensor conditioning interfaces, low-cost consumer appliances, and instrumentation front-ends. Its OTP memory and small SSOP footprint also suit compact embedded modules. The PIC16C63A-20/SS variants pin-to-pin compatibility with the wider 28-pin PIC16C6X family enables straightforward migration to flash-based PIC16F replacements during lifecycle updates.
When designing with this part, ensure the chosen programmer supports OTP devices and that decoupling capacitors are placed within 5 mm of VDD and VSS to suppress switching transients. Note that OTP parts cannot be reprogrammed in-circuit, so engineering samples should be allocated for code bring-up before committing to production volumes.
Аналоги без доработки для PIC16C63A-20/SS — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC16C63A-20/SS (тот же форм-фактор и посадочное место) — отличается по Package, ADC, Operating Temperature, Timers, Mounting Type.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC16C63A-04I/SS
✅ Прямая замена✓ В наличии
$5.55 / шт.
Открыть даташит →PIC16C63A-20I/SS
✅ Прямая замена✓ В наличии
$4.4 / шт.
Открыть даташит →PIC16C63A-20/SS Максимальные параметры и электрические характеристики
| Core Architecture | PIC16CXX 8-bit RISC (mid-range) |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 7 KB (4K x 14) |
| RAM | 192 bytes |
| EEPROM | Not present |
| Maximum Clock Speed | 20 MHz |
| Instruction Execution Time | 200 ns |
| Operating Voltage Range | 2.5 V to 6.0 V |
| I/O Pins | 22 |
| Корпус | 28-pin SSOP (SS) |
| Тип монтажа | Surface Mount |
| Диапазон рабочих температур | -40C to +85C (Industrial) |
| USART | Yes (1x) |
| SSP (SPI / I2C) | Yes (SPI master/slave, I2C master/slave) |
| Analog Comparators | Yes (2) |
| Watchdog Timer | Yes |
| Brown-out Reset | Yes |
| Power-on Reset | Yes |
| Code Protection | Yes (programmable) |
| Timer Modules | Timer0, Timer1, Timer2 |
| CCP Modules | Yes (1x Capture/Compare/PWM) |
Конфигурация выводов PIC16C63A-20/SS
| Контакт 1 | MCLR/VPP — Master Clear (active-low reset) / Programming voltage input |
| Контакт 2 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| Контакт 3 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| Контакт 4 | RA2/AN2 — PORTA bit 2 / analog input 2 |
| Контакт 5 | RA3/AN3/VREF — PORTA bit 3 / analog input 3 / external ADC reference |
| Контакт 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Контакт 7 | RA5/SS/AN4 — PORTA bit 5 / SSP slave select / analog input 4 |
| Контакт 8 | VSS — Ground reference |
| Контакт 9 | OSC1/CLKIN — Oscillator crystal input / external clock in |
| Контакт 10 | OSC2/CLKOUT — Oscillator crystal output / clock out |
| Контакт 11 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / Timer1 clock input |
| Контакт 12 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / Capture-Compare-PWM 2 |
| Контакт 13 | RC2/CCP1 — PORTC bit 2 / Capture-Compare-PWM 1 |
| Контакт 14 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Контакт 15 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Контакт 16 | RC5/SDO — PORTC bit 5 / SPI data out |
| Контакт 17 | RC6/TX/CK — PORTC bit 6 / USART async transmit / sync clock |
| Контакт 18 | RC7/RX/DT — PORTC bit 7 / USART async receive / sync data |
| Контакт 19 | VSS — Ground reference |
| Контакт 20 | VDD — Positive supply |
| Контакт 21 | RB0/INT — PORTB bit 0 / external interrupt |
| Контакт 22 | RB1 — PORTB bit 1 |
| Контакт 23 | RB2 — PORTB bit 2 |
| Контакт 24 | RB3 — PORTB bit 3 |
| Контакт 25 | RB4 — PORTB bit 4 |
| Контакт 26 | RB5 — PORTB bit 5 |
| Контакт 27 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Контакт 28 | RB7/PGD — PORTB bit 7 / ICSP data |
Типичное применение
PIC16C63A-20/SS подходит для 6 применениеs: Industrial Control Panels, Motor Drive Front-Ends, Sensor Conditioning Interfaces, Low-Cost Consumer Appliances, Instrumentation Front-Ends, Compact Embedded Modules.
Industrial Control Panels
The PIC16C63A-20/SS suits industrial control panels because its 7 KB OTP memory holds complete panel logic for relay sequencing, indicator driving, and keypad decoding without external storage. The 22 digital I/O lines map directly to matrix keypads, LED rows, and opto-isolated outputs, while the USART and SSP support isolated RS-485 links and I2C sensor chains. With 200 ns instruction execution and 35 single-word instructions, deterministic scan loops under 5 ms are achievable for HMI refresh.
Рекомендуется
Motor Drive Front-Ends
For motor drive front-ends, the PIC16C63A-20/SS provides 20 MHz throughput to generate PWM patterns, decode Hall-sensor input, and implement closed-loop speed control without external timers. The integrated Capture/Compare/PWM (CCP) module delivers hardware PWM, freeing CPU cycles for sensor fusion and protection logic. The 2.5 V to 6.0 V supply range lets the MCU share the motor rail directly, simplifying BOM.
Рекомендуется
Sensor Conditioning Interfaces
In sensor conditioning interfaces, the PIC16C63A-20/SS leverages its dual analog comparators and 10-bit ADC-friendly I/O to read thermistors, photodiodes, and bridge sensors with on-board excitation control. The SSP block handles I2C communication with external ADCs or digital sensors, while the USART streams processed readings to a host controller. With 192 bytes of RAM and 7 KB of code, the MCU can host linearization, averaging, and fault-detection algorithms.
Рекомендуется
Low-Cost Consumer Appliances
The PIC16C63A-20/SS fits cost-sensitive consumer appliances such as coffee makers, washing-machine sub-modules, and small kitchen devices where BOM is the dominant constraint. Its OTP memory prevents firmware theft at high production volumes, while 22 I/O lines drive segment displays, button matrices, and triac-fired loads. Low-power sleep currents of 1 µA typical at 3 V / 32 kHz keep standby energy within energy-star limits.
Рекомендуется
Instrumentation Front-Ends
For instrumentation front-ends, the PIC16C63A-20/SS combines the USART and SSP to drive LCD character displays, rotary encoders, and serial-port diagnostics in bench-top meters and data loggers. The 200 ns instruction execution enables real-time FIR filtering of up to 8 samples per cycle, while 7 KB of code fits menu systems, calibration tables, and Modbus-style protocols. Brown-out reset and watchdog timer protect against field glitches.
Рекомендуется
Compact Embedded Modules
The PIC16C63A-20/SS serves compact embedded modules such as wireless sensor nodes, RFID reader heads, and serial-bridge adapters where the 28-pin SSOP footprint keeps the PCB under 25 mm x 25 mm. Its 20 MHz throughput handles protocol parsing (Modbus, custom binary), while the SSP master mode talks to SPI peripherals like EEPROMS, RTCs, and accelerometers. Brown-out reset and watchdog timer protect against voltage dips on long cable runs.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC16C63A-20/SS — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC16C63A-04I/SS | PIC16C63A-20I/SS | PIC16C63A/JW |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SSOP-28 | SSOP-28 - same | SSOP-28 - same | CDIP-28 (windowed) - different |
| Program Memory | 7 KB OTP | 7 KB OTP | 7 KB OTP | 7 KB EPROM (UV-erasable) |
| Max Clock Speed | 20 MHz | 4 MHz | 20 MHz | 20 MHz |
| RAM | 192 bytes | 192 bytes | 192 bytes | 192 bytes |
| I/O Pins | 22 | 22 | 22 | 22 |
| Operating Voltage | 2.5 V to 6.0 V | 2.5 V to 6.0 V | 2.5 V to 6.0 V | 2.5 V to 6.0 V |
| Temperature Grade | Commercial | Industrial | Industrial | Commercial (windowed ceramic) |
| Memory Type | OTP (one-time programmable) | OTP | OTP | Windowed EPROM (UV-erasable) |
Ключевые отличия
- Same-die industrial temp grade option (против PIC16C63A-20I/SS)
- Lower-speed industrial variant for power-sensitive designs (против PIC16C63A-04I/SS)
- Windowed EPROM for development (против PIC16C63A/JW)
Заметки по проектированию
OTP EPROM cannot be reprogrammed in-circuit. Allocate engineering samples (such as PIC16C63A/JW windowed ceramic or PIC16F73-I/SO flash parts) for firmware bring-up before committing to PIC16C63A-20/SS OTP production units. Reprogramming a programmed OTP device is impossible, so any firmware bug at the production stage requires full board scrap. Always verify configuration bits in the development sample first.
Place a 100 nF decoupling capacitor within 5 mm of each VDD/VSS pair, plus a bulk 10 uF tantalum or ceramic on the main supply rail. The PIC16C63A-20/SS draws 15 mA typical at 5 V / 20 MHz, so trace widths should handle 50 mA peak with a 0.5 V or less drop. Brown-out reset is enabled by configuration bit and should be left on to avoid undefined execution on slow-rising supplies.
Keep the SSOP-28 PCB footprint tight: 0.65 mm pitch, 5.30 mm body width, and exposed pad routed to the ground plane for thermal relief. Place the crystal within 10 mm of OSC1/OSC2 pins with short, symmetrical traces to minimize stray capacitance. For high-noise environments, add a 4.7 kohm pull-up on MCLR and a guard ring around the analog comparator pins (RA0-RA3).
The USART pins (RC6/RC7) and SSP pins (RC3/RC4/RC5) drive high-frequency edges when running at 20 MHz; route them away from analog comparator inputs to reduce crosstalk. If I2C lines exceed 100 kHz, add 4.7 kohm pull-ups and keep total capacitance below 200 pF for reliable communication. Long oscillator traces or missing ground flooding may force the ICSP programming interface to fail at room temperature.
Информация о соответствии
Compliance status not specified in verified distributor data; PIC16C OTP parts are typically not AEC-Q100 qualified - confirm with Microchip material declaration for RoHS/REACH status before production
