PIC16C63A-20/SS - 8-Bit 20MHz OTP MCU 7KB | Microchip
料号： PIC16C63A-20/SS ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $4.95 | $4.95 |
| 10 | $4.45 | $44.50 |
| 100 | $3.96 | $396.00 |
| 500 | $3.56 | $1,780.00 |
| 1,000 | $3.17 | $3,170.00 |
PIC16C63A-20/SS 概述
A mid-range PIC microcontroller is a class of 8-bit RISC processor that balances code density, peripheral integration, and cost, sitting between baseline PIC10/12/16 devices and the higher-performance PIC18 family. These MCUs use a 14-bit instruction word and Harvard bus topology, allowing simultaneous instruction fetch and data access. They are widely adopted in industrial, consumer, and automotive subsystems where compact code, predictable timing, and a small PCB footprint are priorities.
Key features include a wide operating voltage range from 2.5 V to 6.0 V, industrial and commercial temperature grades, low-power operation with 15 µA typical current at 5 V / 4 MHz and as little as 1 µA at 3 V / 32 kHz, plus 35 single-word instructions of which only program branches take two cycles. The PIC16C63A integrates dual analog comparators, a USART, and a synchronous serial port (SSP) supporting SPI and I2C master/slave modes, enabling direct connectivity to sensors, EEPROMs, displays, and other microcontrollers without external glue logic.
The OTP EPROM-based program memory supports prototype and low-volume production runs where in-system reprogrammability is not required. Power-on reset, brown-out detection, watchdog timer, and a programmable code-protection bit harden the device against field faults and unauthorized firmware access. The fully static design simplifies clocking and allows operation across DC to 20 MHz.
Typical applications include industrial control panels, motor drive front-ends, sensor conditioning interfaces, low-cost consumer appliances, and instrumentation front-ends. Its OTP memory and small SSOP footprint also suit compact embedded modules. The PIC16C63A-20/SS variants pin-to-pin compatibility with the wider 28-pin PIC16C6X family enables straightforward migration to flash-based PIC16F replacements during lifecycle updates.
When designing with this part, ensure the chosen programmer supports OTP devices and that decoupling capacitors are placed within 5 mm of VDD and VSS to suppress switching transients. Note that OTP parts cannot be reprogrammed in-circuit, so engineering samples should be allocated for code bring-up before committing to production volumes.
直接替换替代料： PIC16C63A-20/SS ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： PIC16C63A-20/SS （相同外形与封装尺寸） ——差异在于 Package, ADC, Operating Temperature, Timers, Mounting Type.
快速对比工具——选择替代料号进行并排对比：
PIC16C63A-04I/SS
✅ 直接替换✓ 有现货
$5.55 / 个
查看数据手册 →PIC16C63A-20I/SS
✅ 直接替换✓ 有现货
$4.4 / 个
查看数据手册 →PIC16C63A-20/SS 最大额定值与电气特性
| Core Architecture | PIC16CXX 8-bit RISC (mid-range) |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 7 KB (4K x 14) |
| RAM | 192 bytes |
| EEPROM | Not present |
| Maximum Clock Speed | 20 MHz |
| Instruction Execution Time | 200 ns |
| Operating Voltage Range | 2.5 V to 6.0 V |
| I/O Pins | 22 |
| 封装 | 28-pin SSOP (SS) |
| 安装类型 | Surface Mount |
| 工作温度范围 | -40C to +85C (Industrial) |
| USART | Yes (1x) |
| SSP (SPI / I2C) | Yes (SPI master/slave, I2C master/slave) |
| Analog Comparators | Yes (2) |
| Watchdog Timer | Yes |
| Brown-out Reset | Yes |
| Power-on Reset | Yes |
| Code Protection | Yes (programmable) |
| Timer Modules | Timer0, Timer1, Timer2 |
| CCP Modules | Yes (1x Capture/Compare/PWM) |
PIC16C63A-20/SS 引脚配置
| 引脚 1 | MCLR/VPP — Master Clear (active-low reset) / Programming voltage input |
| 引脚 2 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| 引脚 3 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| 引脚 4 | RA2/AN2 — PORTA bit 2 / analog input 2 |
| 引脚 5 | RA3/AN3/VREF — PORTA bit 3 / analog input 3 / external ADC reference |
| 引脚 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| 引脚 7 | RA5/SS/AN4 — PORTA bit 5 / SSP slave select / analog input 4 |
| 引脚 8 | VSS — Ground reference |
| 引脚 9 | OSC1/CLKIN — Oscillator crystal input / external clock in |
| 引脚 10 | OSC2/CLKOUT — Oscillator crystal output / clock out |
| 引脚 11 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / Timer1 clock input |
| 引脚 12 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / Capture-Compare-PWM 2 |
| 引脚 13 | RC2/CCP1 — PORTC bit 2 / Capture-Compare-PWM 1 |
| 引脚 14 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| 引脚 15 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| 引脚 16 | RC5/SDO — PORTC bit 5 / SPI data out |
| 引脚 17 | RC6/TX/CK — PORTC bit 6 / USART async transmit / sync clock |
| 引脚 18 | RC7/RX/DT — PORTC bit 7 / USART async receive / sync data |
| 引脚 19 | VSS — Ground reference |
| 引脚 20 | VDD — Positive supply |
| 引脚 21 | RB0/INT — PORTB bit 0 / external interrupt |
| 引脚 22 | RB1 — PORTB bit 1 |
| 引脚 23 | RB2 — PORTB bit 2 |
| 引脚 24 | RB3 — PORTB bit 3 |
| 引脚 25 | RB4 — PORTB bit 4 |
| 引脚 26 | RB5 — PORTB bit 5 |
| 引脚 27 | RB6/PGC — PORTB bit 6 / ICSP clock |
| 引脚 28 | RB7/PGD — PORTB bit 7 / ICSP data |
典型应用
PIC16C63A-20/SS 适用于 6 应用s: Industrial Control Panels, Motor Drive Front-Ends, Sensor Conditioning Interfaces, Low-Cost Consumer Appliances, Instrumentation Front-Ends, Compact Embedded Modules.
Industrial Control Panels
The PIC16C63A-20/SS suits industrial control panels because its 7 KB OTP memory holds complete panel logic for relay sequencing, indicator driving, and keypad decoding without external storage. The 22 digital I/O lines map directly to matrix keypads, LED rows, and opto-isolated outputs, while the USART and SSP support isolated RS-485 links and I2C sensor chains. With 200 ns instruction execution and 35 single-word instructions, deterministic scan loops under 5 ms are achievable for HMI refresh.
推荐
Motor Drive Front-Ends
For motor drive front-ends, the PIC16C63A-20/SS provides 20 MHz throughput to generate PWM patterns, decode Hall-sensor input, and implement closed-loop speed control without external timers. The integrated Capture/Compare/PWM (CCP) module delivers hardware PWM, freeing CPU cycles for sensor fusion and protection logic. The 2.5 V to 6.0 V supply range lets the MCU share the motor rail directly, simplifying BOM.
推荐
Sensor Conditioning Interfaces
In sensor conditioning interfaces, the PIC16C63A-20/SS leverages its dual analog comparators and 10-bit ADC-friendly I/O to read thermistors, photodiodes, and bridge sensors with on-board excitation control. The SSP block handles I2C communication with external ADCs or digital sensors, while the USART streams processed readings to a host controller. With 192 bytes of RAM and 7 KB of code, the MCU can host linearization, averaging, and fault-detection algorithms.
推荐
Low-Cost Consumer Appliances
The PIC16C63A-20/SS fits cost-sensitive consumer appliances such as coffee makers, washing-machine sub-modules, and small kitchen devices where BOM is the dominant constraint. Its OTP memory prevents firmware theft at high production volumes, while 22 I/O lines drive segment displays, button matrices, and triac-fired loads. Low-power sleep currents of 1 µA typical at 3 V / 32 kHz keep standby energy within energy-star limits.
推荐
Instrumentation Front-Ends
For instrumentation front-ends, the PIC16C63A-20/SS combines the USART and SSP to drive LCD character displays, rotary encoders, and serial-port diagnostics in bench-top meters and data loggers. The 200 ns instruction execution enables real-time FIR filtering of up to 8 samples per cycle, while 7 KB of code fits menu systems, calibration tables, and Modbus-style protocols. Brown-out reset and watchdog timer protect against field glitches.
推荐
Compact Embedded Modules
The PIC16C63A-20/SS serves compact embedded modules such as wireless sensor nodes, RFID reader heads, and serial-bridge adapters where the 28-pin SSOP footprint keeps the PCB under 25 mm x 25 mm. Its 20 MHz throughput handles protocol parsing (Modbus, custom binary), while the SSP master mode talks to SPI peripherals like EEPROMS, RTCs, and accelerometers. Brown-out reset and watchdog timer protect against voltage dips on long cable runs.
推荐
推荐产品汇总
工程参考数据： PIC16C63A-20/SS ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PIC16C63A-04I/SS | PIC16C63A-20I/SS | PIC16C63A/JW |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SSOP-28 | SSOP-28 - same | SSOP-28 - same | CDIP-28 (windowed) - different |
| Program Memory | 7 KB OTP | 7 KB OTP | 7 KB OTP | 7 KB EPROM (UV-erasable) |
| Max Clock Speed | 20 MHz | 4 MHz | 20 MHz | 20 MHz |
| RAM | 192 bytes | 192 bytes | 192 bytes | 192 bytes |
| I/O Pins | 22 | 22 | 22 | 22 |
| Operating Voltage | 2.5 V to 6.0 V | 2.5 V to 6.0 V | 2.5 V to 6.0 V | 2.5 V to 6.0 V |
| Temperature Grade | Commercial | Industrial | Industrial | Commercial (windowed ceramic) |
| Memory Type | OTP (one-time programmable) | OTP | OTP | Windowed EPROM (UV-erasable) |
关键差异点
- Same-die industrial temp grade option （对比 PIC16C63A-20I/SS)
- Lower-speed industrial variant for power-sensitive designs （对比 PIC16C63A-04I/SS)
- Windowed EPROM for development （对比 PIC16C63A/JW)
设计说明
OTP EPROM cannot be reprogrammed in-circuit. Allocate engineering samples (such as PIC16C63A/JW windowed ceramic or PIC16F73-I/SO flash parts) for firmware bring-up before committing to PIC16C63A-20/SS OTP production units. Reprogramming a programmed OTP device is impossible, so any firmware bug at the production stage requires full board scrap. Always verify configuration bits in the development sample first.
Place a 100 nF decoupling capacitor within 5 mm of each VDD/VSS pair, plus a bulk 10 uF tantalum or ceramic on the main supply rail. The PIC16C63A-20/SS draws 15 mA typical at 5 V / 20 MHz, so trace widths should handle 50 mA peak with a 0.5 V or less drop. Brown-out reset is enabled by configuration bit and should be left on to avoid undefined execution on slow-rising supplies.
Keep the SSOP-28 PCB footprint tight: 0.65 mm pitch, 5.30 mm body width, and exposed pad routed to the ground plane for thermal relief. Place the crystal within 10 mm of OSC1/OSC2 pins with short, symmetrical traces to minimize stray capacitance. For high-noise environments, add a 4.7 kohm pull-up on MCLR and a guard ring around the analog comparator pins (RA0-RA3).
The USART pins (RC6/RC7) and SSP pins (RC3/RC4/RC5) drive high-frequency edges when running at 20 MHz; route them away from analog comparator inputs to reduce crosstalk. If I2C lines exceed 100 kHz, add 4.7 kohm pull-ups and keep total capacitance below 200 pF for reliable communication. Long oscillator traces or missing ground flooding may force the ICSP programming interface to fail at room temperature.
合规信息
Compliance status not specified in verified distributor data; PIC16C OTP parts are typically not AEC-Q100 qualified - confirm with Microchip material declaration for RoHS/REACH status before production
