PIC16F74-E/L - 8-Bit 20MHz PIC MCU 7KB Flash 44-PLCC | Microchip
Артикул: PIC16F74-E/L ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $7.85 | $7,85 |
| 10 | $7.05 | $70,50 |
| 100 | $6.3 | $630,00 |
| 500 | $5.6 | $2.800,00 |
| 1.000 | $4.95 | $4.950,00 |
PIC16F74-E/L Обзор
A microcontroller (microcontroller unit, MCU) is a single-chip computer that integrates a CPU core, program memory (ROM/FLASH), data RAM, working registers, and a rich set of peripherals (timers, ADC, communications) into a compact package that can be embedded directly into an electronic product. The PIC family uses a Harvard architecture with separate program and data buses, allowing instruction fetch and operand access to occur in the same cycle for deterministic throughput at low clock rates. PIC microcontrollers therefore sit in the hierarchy: microcontroller -> embedded processor -> semiconductor device, and they are typically deployed where deterministic timing, low cost, and low power are required.
Key features of the PIC16F74 include 192 bytes of RAM, 33 digital I/O lines, an 8-channel 8-bit Analog-to-Digital converter (ADC), two 8-bit timers and one 16-bit timer, two Capture/Compare/PWM (CCP) modules, a synchronous serial port configurable as 3-wire SPI or 2-wire I2C, and a USART for asynchronous serial communications. The core supports 35 single-word instructions with a 200 ns instruction cycle at 20MHz, providing predictable execution for real-time control tasks.
Architecturally, the PIC16F74 uses CMOS FLASH process technology with Microchip's nanoWatt power-managed sleep modes and a wide 2.5V-5.5V operating range. A 14-bit instruction word delivers compact code density, while the integrated brown-out reset and watchdog timer improve robustness in industrial environments. The 44-PLCC package exposes most peripheral pins, simplifying PCB layout compared to smaller-pin PIC16F7x cousins.
Typical applications for the PIC16F74-E/L include industrial control systems, HVAC fan/valve controllers, security alarm panels, motor-control signal conditioning, and embedded instrumentation with the 8-bit ADC reading sensor inputs. The extended temperature grade makes it suitable for outdoor or factory-floor equipment.
When designing with the PIC16F74, ensure that your programmer/debugger supports the 5V FLASH programming algorithm (e.g., MPLAB ICD or PICkit) and that decoupling caps of 0.1uF plus bulk 1-10uF are placed close to VDD/VDD2. For low-power designs, leverage the nanoWatt sleep modes to draw sub-microamp standby currents between ADC bursts.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, with data traced to Microchip's official PIC16F74 product page and current distributor listings.
Аналоги без доработки для PIC16F74-E/L — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC16F74-E/L (тот же форм-фактор и посадочное место) — отличается по Package, Timers, Core Architecture, I/O Pins, Serial Interfaces.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC16F74T-I/L
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC16F77-I/L
✅ Прямая замена✓ В наличии
$7.55 / шт.
Открыть даташит →PIC16F74-I/L
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC16F74T-E/L
✅ Прямая замена✓ В наличии
$5.4 / шт.
Открыть даташит →PIC16F74-E/L Максимальные параметры и электрические характеристики
| Core Architecture | 8-bit PIC RISC (Harvard) |
| Program Memory | 7 KB FLASH (4K x 14 instructions) |
| Data RAM | 192 bytes |
| EEPROM | Data EEPROM on-chip |
| Максимальная тактовая частота | 20 MHz |
| Instruction Cycle Time | 200 ns at 20 MHz |
| Supply Voltage (VDD) | 2.5 V to 5.5 V |
| I/O Pins | 33 digital I/O |
| ADC | 8 channels, 8-bit resolution |
| Timers | 2 x 8-bit + 1 x 16-bit |
| CCP Modules | 2 (Capture/Compare/PWM) |
| Serial Interfaces | SSP (SPI / I2C), USART |
| Operating Temperature Grade | -40C to +125C (Extended "-E") |
| Корпус | 44-pin PLCC (16.59 x 16.59 mm) |
| Lead-Free | Yes (lead-free PLCC finish) |
| Programming/Debug | ICSP via MPLAB / PICkit / ICD tools |
Конфигурация выводов PIC16F74-E/L
| Контакт 1 | RA0/AN0 — PORTA bit 0 / Analog input 0 |
| Контакт 2 | RA1/AN1 — PORTA bit 1 / Analog input 1 |
| Контакт 3 | RA2/AN2/VREF- — PORTA bit 2 / Analog input 2 / VREF- |
| Контакт 4 | RA3/AN3/VREF+ — PORTA bit 3 / Analog input 3 / VREF+ |
| Контакт 5 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Контакт 6 | RA5/AN4/SS — PORTA bit 5 / Analog input 4 / SPI slave select |
| Контакт 7 | RE0/RD/AN5 — PORTE bit 0 / Parallel port read / Analog input 5 |
| Контакт 8 | RE1/WR/AN6 — PORTE bit 1 / Parallel port write / Analog input 6 |
| Контакт 9 | RE2/CS/AN7 — PORTE bit 2 / Parallel port chip select / Analog input 7 |
| Контакт 10 | VDD — Positive digital supply |
| Контакт 11 | VSS — Digital ground |
| Контакт 12 | OSC1/CLKI — Oscillator crystal input / external clock |
| Контакт 13 | OSC2/CLKO — Oscillator crystal output / clock out |
| Контакт 14 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator out / Timer1 clock in |
| Контакт 15 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 I/O |
| Контакт 16 | RC2/CCP1 — PORTC bit 2 / CCP1 I/O |
| Контакт 17 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Контакт 18 | RD0/PSP0 — PORTD bit 0 / Parallel slave port bit 0 |
| Контакт 19 | RD1/PSP1 — PORTD bit 1 / Parallel slave port bit 1 |
| Контакт 20 | RD2/PSP2 — PORTD bit 2 / Parallel slave port bit 2 |
| Контакт 21 | RD3/PSP3 — PORTD bit 3 / Parallel slave port bit 3 |
| Контакт 22 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Контакт 23 | RC5/SDO — PORTC bit 5 / SPI data out |
| Контакт 24 | RC6/TX/CK — PORTC bit 6 / USART TX / USART clock |
| Контакт 25 | RC7/RX/DT — PORTC bit 7 / USART RX / USART data |
| Контакт 26 | RD4/PSP4 — PORTD bit 4 / Parallel slave port bit 4 |
| Контакт 27 | RD5/PSP5 — PORTD bit 5 / Parallel slave port bit 5 |
| Контакт 28 | RD6/PSP6 — PORTD bit 6 / Parallel slave port bit 6 |
| Контакт 29 | RD7/PSP7 — PORTD bit 7 / Parallel slave port bit 7 |
| Контакт 30 | VSS — Digital ground |
| Контакт 31 | VDD — Positive digital supply |
| Контакт 32 | RB0/INT — PORTB bit 0 / External interrupt |
| Контакт 33 | RB1 — PORTB bit 1 |
| Контакт 34 | RB2 — PORTB bit 2 |
| Контакт 35 | RB3/PGM — PORTB bit 3 / Low-voltage programming |
| Контакт 36 | RB4 — PORTB bit 4 |
| Контакт 37 | RB5 — PORTB bit 5 |
| Контакт 38 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Контакт 39 | RB7/PGD — PORTB bit 7 / ICSP data |
| Контакт 40 | NC — Not connected (per datasheet) |
| Контакт 41 | NC — Not connected (per datasheet) |
| Контакт 42 | AVDD — Analog positive supply |
| Контакт 43 | AVSS — Analog ground |
| Контакт 44 | MCLR/VPP — Master clear / programming voltage |
Типичное применение
PIC16F74-E/L подходит для 6 применениеs: Industrial Motor & Valve Controller, HVAC Fan & Damper Controller, Security Alarm Panel, Embedded Instrumentation with ADC Front-End, Appliance Control Board, Automotive Aftermarket Accessory Module.
Industrial Motor & Valve Controller
The PIC16F74-E/L fits industrial motor and valve control because its two CCP modules deliver one channel of PWM drive plus one feedback capture channel, while the 8-channel 8-bit ADC reads current, position, and temperature sensor inputs. The 20MHz core and 200 ns instruction cycle sustain deterministic real-time loop rates even with multiple feedback signals. Placed on a control PCB, it drives TRIAC/MOSFET stages via opto-isolated outputs, with the USART forwarding telemetry to a host PLC; unlike ARM Cortex-M parts the PIC16F74-E/L adds the -E extended -40C to +125C temperature grade that is required for cabinet-side installations without extra thermal management.
Рекомендуется
HVAC Fan & Damper Controller
The PIC16F74-E/L is well suited to HVAC fan and damper control where its 8-channel ADC monitors thermistors, duct pressure, and humidity sensors while the CCP PWM output drives a proportional damper actuator. Running at 20MHz from a 3.3V or 5V rail, it sustains the multi-sensor update loop with deterministic latency. Placed in a fan-coil unit controller, it uses the USART to report status to the building automation backbone; the nanoWatt sleep modes drop standby current into the microamp range between sensor sweeps, supporting Energy Star idle targets and the -E extended temperature grade allows rooftop mounting without extra heatsinking.
Рекомендуется
Security Alarm Panel
The PIC16F74-E/L fits intrusion alarm panels because its 33 digital I/O lines scan 8-16 zones of door/window sensors and PIR triggers, while the 8-bit ADC monitors backup battery voltage and tamper loops. The 20MHz RISC core sustains debounced scanning loops with 35 single-word instructions, and the on-chip EEPROM stores zone configuration through power events. Deployed inside a metal enclosure, it triggers sirens and dials out via the USART/SSP-attached modem IC; the -E extended temperature grade supports outdoor unheated equipment sheds, and the FLASH-based ICSP allows firmware updates as installers add new zone types.
Рекомендуется
Embedded Instrumentation with ADC Front-End
The PIC16F74-E/L is a strong fit for embedded instrumentation thanks to its 8-channel 8-bit ADC, which reads strain gauge bridges, thermistors, and 4-20 mA loop sensors through a front-end multiplexer. At 20MHz the core performs scaling, linearization, and digital filtering in real time, while the USART pushes calibrated readings to an external display or host. Used inside a panel meter or process indicator, it eliminates an external ADC and references the supply via dedicated AVSS/VDD pins; the 7KB FLASH hosts full calibration tables, and the SSP supports an I2C LCD display for human readout without extra driver ICs.
Рекомендуется
Appliance Control Board
The PIC16F74-E/L fits white-goods control boards - washing machines, dishwashers, and induction cooktops - because its two CCP channels handle one motor PWM and one zero-cross detect, while the 8-channel ADC reads water level, motor current, and NTC temperature. The -E extended temperature grade survives the under-counter and behind-the-panel thermal environment, and the FLASH program memory stores the wash-cycle and safety-look-up tables that the on-chip EEPROM cannot hold. Mounted on the appliance main board, the PIC16F74-E/L drives TRIACs through opto-isolators; the ICSP interface lets the line replace firmware for model variants without retooling.
Рекомендуется
Automotive Aftermarket Accessory Module
The PIC16F74-E/L fits automotive aftermarket accessory modules - alarm add-ons, lighting controllers, and trailer interfaces - because its wide 2.5V-5.5V supply tolerance survives load-dump events when paired with a TVS, and the 8-channel ADC monitors battery voltage, ignition sense, and switch inputs. The CCP modules drive relay and LED PWM dimming, while the SSP-based SPI bus talks to an external CAN or LIN transceiver. The -E extended temperature grade supports under-hood or dashboard mounting without thermal derating; the ICSP pins route to a service connector so dealers can flash regional firmware variants.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC16F74-E/L — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC16F74T-I/L | PIC16F77-I/L | PIC16F747-E/ML | PIC16F74-I/L | PIC16F74T-E/L |
|---|---|---|---|---|---|---|
| Package | 44-PLCC (L) | 44-PLCC (L) - same | 44-PLCC (L) - same | 44-QFN (ML) - different | 44-PLCC (L) - same | 44-PLCC (L) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program FLASH | 7 KB (4K x 14) | 7 KB (same) | 14 KB (+100%) | 7 KB (same) | 7 KB (same) | 7 KB (same) |
| Data RAM | 192 bytes | 192 bytes (same) | 368 bytes (+92%) | 192 bytes (same) | 192 bytes (same) | 192 bytes (same) |
| Maximum Clock | 20 MHz | 20 MHz (same) | 20 MHz (same) | 20 MHz (same) | 20 MHz (same) | 20 MHz (same) |
| ADC Channels x Resolution | 8 x 8-bit | 8 x 8-bit (same) | 8 x 8-bit (same) | 8 x 8-bit (same) | 8 x 8-bit (same) | 8 x 8-bit (same) |
| CCP Modules | 2 | 2 (same) | 2 (same) | 2 (same) | 2 (same) | 2 (same) |
| Temperature Grade | -40C to +125C (-E extended) | -40C to +85C (-I industrial) | -40C to +85C (-I industrial) | -40C to +125C (-E extended) | -40C to +85C (-I industrial) | -40C to +125C (-E extended) |
Ключевые отличия
- Extended -40C to +125C temperature grade vs only -I in standard PIC16F74-I/L (против PIC16F74-I/L)
- Doubles program FLASH vs baseline PIC16F73 (против PIC16F73-I/SO)
- On-chip data EEPROM for non-volatile parameter storage vs PIC16F72 baseline (против PIC16F72-E/SP)
- Two CCP modules for simultaneous PWM and capture feedback vs single-CCP PIC16F720 (против PIC16F720-I/P)
Заметки по проектированию
Estimated: at 20MHz and 5V VDD, the PIC16F74-E/L draws roughly 10-15 mA active and below 1 uA in SLEEP mode. Place a 0.1 uF ceramic decoupling cap as close as possible to each VDD/AVDD pin pair, and add a bulk 1-10 uF tantalum or ceramic on the main 5V rail. For noise-sensitive analog reads, separate AVSS from VSS at the regulator and star-ground both back to a single-point ground near the MCU. Use the brown-out reset (BOR) feature to prevent code corruption during 3.3V brown-out events.
Estimated: with all 33 I/O pins sourcing 20 mA worst case (per pin spec) the PIC16F74-E/L could draw up to 660 mA total, but real designs stay below 100 mA. The 44-PLCC package theta_JA is roughly 40-50 C/W, so at 25C ambient and 100 mA VDD*IDD (~0.5 W) the junction rises only 25C, leaving 80C of headroom in the -E extended grade. For sustained high-load industrial designs, use thermal vias under the PLCC socket and avoid mounting the IC directly above heat-generating regulators.
Keep the 20MHz oscillator traces short and routed over a continuous ground plane. Place the 22 pF-33 pF load capacitors within 5 mm of OSC1/OSC2 and use a guard ring tied to ground if the clock traces cross sensitive analog lines. Reserve a 2-pin ICSP header (PGC/PGD plus MCLR/VPP and ground) at the board perimeter so production firmware can be flashed without an inline programmer socket. Avoid routing the MCLR/VPP trace near high-dV/dt switching nodes.
Do not confuse the -E extended temperature suffix (-40C to +125C) with the -I industrial suffix (-40C to +85C) - the PIC16F74-E/L is the extended grade; if you order the -I variant you lose 40C of upper margin. Do not pull MCLR low at power-up before the VDD rail stabilizes, or the device will enter programming mode. Verify CONFIG fuse settings (oscillator, watchdog, code protect, brown-out) match the design before mass production - the -LF version uses FLASH configuration words and must be programmed with a 5V algorithm.
When using the 8-bit ADC for sensor reads, place an RC low-pass filter (typically 1 kohm + 100 nF) on each ANx input to attenuate clock harmonics and switching noise from digital outputs. Use the ADC in SLEEP mode with the internal RC oscillator to remove CPU noise from the conversion. The AVSS pin must tie to a clean analog ground that is star-grounded to the MCU VSS, not chained from a digital ground bus. For multi-channel scanning, allow at least 20 us acquisition time before starting the conversion.
Информация о соответствии
RoHS compliant per Microchip product page; /L suffix indicates lead-free PLCC finish. Not AEC-Q100 qualified - this is an industrial extended temperature part, not an automotive-qualified MCU.
