PIC16LF874-04I/L - 8-Bit MCU, 7KB Flash, 4MHz, 44-PLCC | Microchip
Артикул: PIC16LF874-04I/L ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $9.42 | $9,42 |
| 10 | $8.95 | $89,50 |
| 100 | $7.88 | $788,00 |
| 500 | $7.05 | $3.525,00 |
| 1.000 | $6.2 | $6.200,00 |
PIC16LF874-04I/L Обзор
A PIC microcontroller is a RISC-based, Harvard-architecture 8-bit MCU widely used in embedded control. Within the broader taxonomy, it sits as: PIC16F family -> PIC16F87x sub-family -> 8-bit microcontroller -> microcontroller unit (MCU) -> semiconductor. The 'LF' prefix designates the low-voltage (2.0V-5.5V) Flash variant, while '874' denotes a 7KB Flash / 192B RAM member with 33 digital I/O lines, integrated A/D, USART, and Capture/Compare/PWM peripherals. The '04' speed suffix specifies a 4 MHz maximum oscillator frequency, and the 'I' suffix marks the industrial operating temperature grade.
Key features include 7KB Flash program memory, 192 bytes of data RAM, 128 bytes of EEPROM data memory, 33 digital I/O lines, a 10-bit Analog-to-Digital Converter with multiple input channels, a USART serial port, Capture/Compare/PWM modules, and a watchdog timer. The integrated peripherals reduce external component count and BOM cost in embedded designs.
Architecturally, the device uses a 14-bit instruction word with 35 single-cycle instructions, providing deterministic real-time response. Harvard bus architecture separates program and data memories, allowing instruction fetch and data access in a single clock cycle. The 4 MHz oscillator combined with a 4:1 instruction cycle ratio yields a 1 MIPS execution throughput.
Typical applications include industrial process control, sensor interfacing and data acquisition, motor control loops, low-power portable instruments, automotive body electronics (non-safety), and consumer appliance controllers. The wide operating voltage range (2.0V-5.5V) enables direct battery-powered and USB-bus-powered designs. The PLCC-44 package also supports through-hole and socketed installation, easing prototype rework and field service.
When designing with this part, observe the maximum 4 MHz clock input and ensure decoupling capacitors (typically 100 nF) are placed close to VDD/SS pins. The PLCC-44 socket footprint allows easy firmware swap during development. Industrial-grade operation covers -40C to +85C, suitable for most factory and outdoor environments.
This page synthesizes distributor pricing, parametric alternatives, and practical design notes not found in the manufacturer datasheet alone.
Аналоги без доработки для PIC16LF874-04I/L — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC16LF874-04I/L (тот же форм-фактор и посадочное место) — отличается по Core Architecture, Mounting Type, Package, ADC, Timers.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC16LF874-04/L
✅ Прямая замена✓ В наличии
$4.41 / шт.
Открыть даташит →PIC16F874A-I/L
✅ Прямая замена✓ В наличии
$5.2 / шт.
Открыть даташит →PIC16LF871-I/L
✅ Прямая замена✓ В наличии
$4.21 / шт.
Открыть даташит →PIC16LF877-04I/L
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$6.35 / шт.
Открыть даташит →PIC16LF874-04I/L Максимальные параметры и электрические характеристики
| Product Family | PIC16F87x |
| Core Architecture | 8-bit RISC (PIC) |
| Program Memory Type | Flash |
| Program Memory Size | 7 KB (4K x 14 words) |
| Data RAM | 192 bytes |
| EEPROM Data Memory | 128 bytes |
| Maximum CPU Frequency | 4 MHz |
| Operating Voltage Range | 2.0 V to 5.5 V |
| I/O Pins | 33 |
| A/D Converter | 10-bit, multiple input channels |
| Serial Interface | USART |
| PWM Modules | Capture/Compare/PWM (CCP) |
| Watchdog Timer | Yes |
| Диапазон рабочих температур | -40 C to +85 C (Industrial) |
| Корпус | 44-pin PLCC (J-Lead), 16.59 x 16.59 mm |
| Тип монтажа | Surface Mount (PLCC socket compatible) |
Конфигурация выводов PIC16LF874-04I/L
| Контакт 1 | MCLR/VPP — Master Clear reset input / programming voltage |
| Контакт 2 | OSC1/CLKIN — Oscillator crystal input / external clock |
| Контакт 3 | OSC2/CLKOUT — Oscillator crystal output / clock out |
| Контакт 4 | RA0/AN0 — PORTA bit 0 / ADC input 0 |
| Контакт 5 | RA1/AN1 — PORTA bit 1 / ADC input 1 |
| Контакт 6 | RA2/AN2 — PORTA bit 2 / ADC input 2 |
| Контакт 7 | RA3/AN3 — PORTA bit 3 / ADC input 3 |
| Контакт 8 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Контакт 9 | RA5/SS/AN4 — PORTA bit 5 / SPI slave select / ADC input 4 |
| Контакт 10 | VSS — Ground reference |
| Контакт 11 | VDD — Positive supply (2.0V to 5.5V) |
| Контакт 12 | RB0/INT — PORTB bit 0 / external interrupt |
| Контакт 13 | RB1 — PORTB bit 1 |
| Контакт 14 | RB2 — PORTB bit 2 |
| Контакт 15 | RB3/PGM — PORTB bit 3 / low-voltage programming |
| Контакт 16 | RB4 — PORTB bit 4 |
| Контакт 17 | RB5 — PORTB bit 5 |
| Контакт 18 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Контакт 19 | RB7/PGD — PORTB bit 7 / ICSP data |
| Контакт 20 | RC0/T1OSO — PORTC bit 0 / Timer1 oscillator output |
| Контакт 21 | RC1/T1OSI — PORTC bit 1 / Timer1 oscillator input |
| Контакт 22 | RC2/CCP1 — PORTC bit 2 / Capture-Compare-PWM 1 |
| Контакт 23 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Контакт 24 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Контакт 25 | RC5/SDO — PORTC bit 5 / SPI data out |
| Контакт 26 | RC6/TX/CK — PORTC bit 6 / USART TX / clock |
| Контакт 27 | RC7/RX/DT — PORTC bit 7 / USART RX / data |
| Контакт 28 | RD0 — PORTD bit 0 |
| Контакт 29 | RD1 — PORTD bit 1 |
| Контакт 30 | RD2 — PORTD bit 2 |
| Контакт 31 | RD3 — PORTD bit 3 |
| Контакт 32 | RD4 — PORTD bit 4 |
| Контакт 33 | RD5 — PORTD bit 5 |
| Контакт 34 | RD6 — PORTD bit 6 |
| Контакт 35 | RD7 — PORTD bit 7 |
| Контакт 36 | RE0/RD — PORTE bit 0 / read control |
| Контакт 37 | RE1/WR — PORTE bit 1 / write control |
| Контакт 38 | RE2/CS — PORTE bit 2 / chip select |
| Контакт 39 | VSS — Ground reference |
| Контакт 40 | VDD — Positive supply (2.0V to 5.5V) |
| Контакт 41 | NC — Not connected (per datasheet) |
| Контакт 42 | NC — Not connected (per datasheet) |
| Контакт 43 | NC — Not connected (per datasheet) |
| Контакт 44 | NC — Not connected (per datasheet) |
Типичное применение
PIC16LF874-04I/L подходит для 6 применениеs: Industrial Process Control, Sensor Interfacing and Data Acquisition, Low-Power Portable Instruments, Consumer Appliance Controllers, Automotive Body Electronics (Non-Safety), Motor Control and PWM Drive.
Industrial Process Control
The PIC16LF874-04I/L's 33 I/O pins, 10-bit ADC, and USART make it a strong fit for industrial process control applications including sensor aggregation and actuator drive. At 4 MHz (1 MIPS), the MCU can poll multiple analog inputs from temperature, pressure, and flow sensors while maintaining deterministic loop times for PID control loops. Its 2.0V-5.5V operating range allows direct interface to 24V-sourced industrial rails via simple resistor dividers and to 5V logic without level shifters. The wide -40C to +85C industrial temperature grade ensures operation in factory-floor enclosures.
Рекомендуется
Sensor Interfacing and Data Acquisition
The PIC16LF874-04I/L's integrated 10-bit ADC with multiple input channels is well-suited for multi-sensor data acquisition front ends in instrumentation and remote monitoring. Engineers can sequence ADC conversions across analog sensor arrays (temperature, pressure, humidity) and transmit results via the on-chip USART to a host logger or display. The 192-byte RAM supports circular buffering of ADC samples, while the 128-byte EEPROM retains calibration constants across power cycles. The 4 MHz clock is sufficient for sampling rates up to ~50 kSPS aggregate.
Рекомендуется
Low-Power Portable Instruments
Battery-powered portable instruments benefit from the PIC16LF874-04I/L's 2.0V-5.5V supply range, which supports direct operation from 2x AA alkaline or single-cell Li-ion batteries. The PIC16LF sleep mode combined with selective peripheral shutdown enables multi-year battery life in intermittent-sampling applications such as handheld thermometers, data loggers, and field calibration tools. The 33 I/O lines allow direct connection to LCD panels, keypads, and measurement transducers without external glue logic, reducing BOM cost and PCB area in compact portable enclosures.
Рекомендуется
Consumer Appliance Controllers
Consumer appliances such as washing machines, microwave ovens, refrigerators, and air-conditioner control boards rely on the PIC16LF874-04I/L's combination of integrated peripherals and Flash-based program memory. The CCP/PWM module drives motor speed controls, valve actuators, and indicator LEDs directly from the MCU. Flash-based in-circuit programming via ICSP allows manufacturers to update firmware for regulatory compliance or feature upgrades without hardware changes. The wide operating voltage range (2.0V-5.5V) accommodates both rectified-mains-derived and battery-backed power architectures common in modern appliances.
Рекомендуется
Automotive Body Electronics (Non-Safety)
While the PIC16LF874-04I/L is industrial-grade (-40C to +85C) rather than AEC-Q100 qualified, it is well suited to non-safety automotive body-electronics applications such as interior lighting controllers, seat-position memory, HVAC blend-door actuators, and accessory multiplexers. The 33 I/O pins and integrated 10-bit ADC support direct interface to switch panels, position sensors, and small DC motor bridges. The 5V-tolerant digital inputs can read automotive 12V switch signals via simple resistor dividers, reducing external component count.
Рекомендуется
Motor Control and PWM Drive
The PIC16LF874-04I/L's Capture/Compare/PWM (CCP) module generates precise PWM signals for low-power DC motor speed control, LED dimming, and solenoid drive applications. With 4 MHz CPU clock, PWM resolution up to 10 bits at 4 kHz switching frequency is achievable, sufficient for brushed DC motor commutation in toys, small appliances, and hobby robotics. The integrated 10-bit ADC closes the control loop by sampling motor current sense amplifiers or back-EMF signals, enabling basic PID control without external DSP hardware.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC16LF874-04I/L — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC16LF874-04/L | PIC16F874A-I/L | PIC16LF877-04I/L |
|---|---|---|---|---|
| Package | 44-PLCC (16.59 x 16.59 mm) | 44-PLCC - same | 44-PLCC - same | 44-PLCC - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Max CPU Frequency | 4 MHz | 4 MHz | 20 MHz (+400%) | 4 MHz |
| Program Flash | 7 KB | 7 KB | 7.2 KB (+2.9%) | 14 KB (+100%) |
| Data RAM | 192 B | 192 B | 192 B | 368 B (+92%) |
| Operating Voltage | 2.0V to 5.5V | 2.0V to 5.5V | 2.0V to 5.5V | 2.0V to 5.5V |
| I/O Pins | 33 | 33 | 33 | 33 |
| Temperature Grade | Industrial (-40C to +85C) | Commercial (0C to +70C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) |
Ключевые отличия
- Industrial temperature grade at 4 MHz speed grade (против PIC16LF874-04/L)
- Lower 4 MHz speed grade for noise-immune low-EMI designs (против PIC16F874A-I/L)
- Compact 7 KB Flash / 192 B RAM for simpler code bases (против PIC16LF877-04I/L)
Заметки по проектированию
The PIC16LF874-04I/L accepts 2.0V-5.5V at VDD pins 11 and 40; both pins MUST be connected to a common supply rail. Place a 100 nF ceramic decoupling capacitor within 5 mm of each VDD pin and a bulk 10 uF tantalum or aluminum capacitor at the board power entry. For noisy industrial environments, add a ferrite bead and 4.7 uF capacitor on the supply rail feeding the MCU to suppress transients from relay coils and motor bridges.
A common pitfall is leaving the MCLR/VPP pin floating: it MUST be tied to VDD through a 10 kohm resistor for normal operation and pulled low for reset. The PIC16LF874-04I/L does not have internal weak pull-ups on MCLR (unlike later PIC18 families). For ICSP programming, ensure the MCLR line is reachable via a dedicated test point or header. Also, pins RB3, RB6, RB7 serve dual-purpose ICSP functions - avoid adding series resistors that exceed 1 kohm on these lines.
PLCC-44 sockets enable easy firmware swap during development and field service; recommend Aries or 3M through-hole PLCC sockets for production. Keep the oscillator traces (OSC1, OSC2) short (under 10 mm) and surrounded by a ground pour to minimize EMI pickup. The ADC analog inputs (AN0-AN4) should be routed away from switching digital lines; place the AVdd filter capacitor close to the analog reference if used. Trace impedance is not critical at 4 MHz, so standard 50 ohm microstrip is unnecessary.
When using the internal 10-bit ADC, add a 100 nF + 10 uF decoupling network at AVdd (separate from digital VDD if possible) and place the analog signal traces away from digital switching lines. The ADC input impedance is typically 10 kohm, so source impedance below 2 kohm is required for full 10-bit accuracy at moderate conversion rates. For precision measurements, oversample and average to improve effective resolution beyond 10 bits.
Информация о соответствии
RoHS and REACH compliant per Microchip product page; lead-free and halogen-free assembly. Industrial-grade (I) part is not AEC-Q100 qualified - for safety-critical automotive applications, consider AEC-Q100 qualified PIC16 variants. Reach SVHC compliance verified per Microchip material declaration.
