PIC18F45J10T-I/ML - 8-Bit 40MHz 32KB Flash MCU | Microchip
Артикул: PIC18F45J10T-I/ML ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $3.5 | $3,50 |
| 10 | $3.1 | $31,00 |
| 100 | $2.72 | $272,00 |
| 500 | $2.42 | $1.210,00 |
| 1.000 | $2.18 | $2.180,00 |
PIC18F45J10T-I/ML Обзор
Аналоги без доработки для PIC18F45J10T-I/ML — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC18F45J10T-I/ML (тот же форм-фактор и посадочное место) — отличается по Core Architecture, ADC, Package, Timers, Operating Temperature.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC18F45J10-I/ML
✅ Прямая замена✓ В наличии
$2.45 / шт.
Открыть даташит →PIC18F45K22-I/ML
✅ Прямая замена✓ В наличии
$2.65 / шт.
Открыть даташит →PIC18F45K22T-I/ML
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$1.95 / шт.
Открыть даташит →PIC18F44J10T-I/ML
✅ Прямая замена✓ В наличии
$2.78 / шт.
Открыть даташит →PIC18F45J10T-I/ML Максимальные параметры и электрические характеристики
| Core Architecture | PIC18J, 8-bit RISC |
| Максимальная тактовая частота | 40 MHz |
| Program Memory (Flash) | 32 KB (16K x 16 words) |
| Data SRAM | 1024 bytes |
| Data EEPROM | Not present |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| Диапазон рабочих температур | -40 C to +85 C (Industrial, -I suffix) |
| I/O Pins | 34 (bidirectional) |
| Package Type | 44-pin QFN (8x8 mm) with exposed pad, designation ML |
| Тип монтажа | Surface Mount |
| ADC | 10-bit, 13 channels |
| Timers | 4 (Timer0/1/2/3) |
| Enhanced USART | 1 (with LIN master/slave hardware) |
| MSSP (I2C/SPI) | 2 ports with I2C address masking |
| Power-Saving Modes | nanoWatt: Run, Idle, Sleep, deep Sleep |
| ICSP / In-Circuit Programming | Yes (2-wire ICD support) |
| Статус RoHS | Compliant |
| Lead-Free / Halogen-Free | Yes (per Microchip RoHS data) |
Конфигурация выводов PIC18F45J10T-I/ML
| Контакт 1 | RA0/AN0 — PORTA bit 0 / Analog input channel 0 |
| Контакт 2 | RA1/AN1 — PORTA bit 1 / Analog input channel 1 |
| Контакт 3 | RA2/AN2/VREF- — PORTA bit 2 / Analog channel 2 / ADC VREF- |
| Контакт 4 | RA3/AN3/VREF+ — PORTA bit 3 / Analog channel 3 / ADC VREF+ |
| Контакт 5 | RA4 — PORTA bit 4 |
| Контакт 6 | RA5/AN4 — PORTA bit 5 / Analog channel 4 |
| Контакт 7 | RA6 — PORTA bit 6 |
| Контакт 8 | RA7 — PORTA bit 7 |
| Контакт 9 | VSS1 — Ground reference for PORTA and PORTB |
| Контакт 10 | VDD1 — Positive supply for PORTA and PORTB |
| Контакт 11 | RB0/INT0 — PORTB bit 0 / External interrupt 0 |
| Контакт 12 | RB1/INT1 — PORTB bit 1 / External interrupt 1 |
| Контакт 13 | RB2/INT2 — PORTB bit 2 / External interrupt 2 |
| Контакт 14 | RB3 — PORTB bit 3 |
| Контакт 15 | RB4 — PORTB bit 4 |
| Контакт 16 | RB5 — PORTB bit 5 |
| Контакт 17 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Контакт 18 | RB7/PGD — PORTB bit 7 / ICSP data |
| Контакт 19 | VSS2 — Ground reference for PORTC and PORTD |
| Контакт 20 | VDD2 — Positive supply for PORTC and PORTD |
| Контакт 21 | RC0/T1OSO — PORTC bit 0 / Timer1 oscillator output |
| Контакт 22 | RC1/T1OSI — PORTC bit 1 / Timer1 oscillator input |
| Контакт 23 | RC2/CCP1 — PORTC bit 2 / Capture/Compare/PWM 1 |
| Контакт 24 | RC3/SCK1/SCL1 — PORTC bit 3 / MSSP1 SPI clock / I2C clock |
| Контакт 25 | RC4/SDI1/SDA1 — PORTC bit 4 / MSSP1 SPI data in / I2C data |
| Контакт 26 | RC5/SDO1 — PORTC bit 5 / MSSP1 SPI data out |
| Контакт 27 | RC6/TX1/CK1 — PORTC bit 6 / EUSART1 TX / clock |
| Контакт 28 | RC7/RX1/DT1 — PORTC bit 7 / EUSART1 RX / data |
| Контакт 29 | VSS3 — Ground reference for PORTE |
| Контакт 30 | VDD3 — Positive supply for PORTE |
| Контакт 31 | RD0 — PORTD bit 0 |
| Контакт 32 | RD1 — PORTD bit 1 |
| Контакт 33 | RD2 — PORTD bit 2 |
| Контакт 34 | RD3 — PORTD bit 3 |
| Контакт 35 | RD4 — PORTD bit 4 |
| Контакт 36 | RD5 — PORTD bit 5 |
| Контакт 37 | RD6 — PORTD bit 6 |
| Контакт 38 | RD7 — PORTD bit 7 |
| Контакт 39 | RE0 — PORTE bit 0 |
| Контакт 40 | RE1 — PORTE bit 1 |
| Контакт 41 | RE2 — PORTE bit 2 |
| Контакт 42 | VUSB — USB voltage detect (not used on J10) |
| Контакт 43 | VDDCORE — Internal regulator output, decouple with cap |
| Контакт 44 | MCLR — Master clear / reset input (active low) |
Типичное применение
PIC18F45J10T-I/ML подходит для 6 применениеs: Consumer Appliance Control Panels, Battery-Powered Sensor Nodes, Industrial Control Front Ends, Low-Speed Motor Control BLDC/PMSM Front Ends, HVAC Climate Sensor Modules, Low-Cost Lighting Controllers (DMX/DALI Slave).
Consumer Appliance Control Panels
The PIC18F45J10T-I/ML fits consumer appliance control panels because its 32 KB Flash and 1 KB SRAM easily hold keypad-scan, LCD/LED-driver, and user-interface state-machine firmware for washers, ovens, and microwaves. The 40 MHz / 10 MIPS core runs debounce, PID-loop and timer-based event scheduling at comfortable headroom, while the 2.0 V-3.6 V supply range and nanoWatt sleep modes suit mains-powered appliances with standby power budgets below 100 mW. The enhanced USART with LIN master hardware lets the same MCU talk to a power-inverter or motor-driver board over LIN, and two MSSP ports drive a character LCD plus an EEPROM or sensor I2C bus. Its 34 I/O lines cover key matrix, LED drivers, buzzer PWM, and triac optocoupler interfaces without external mux ICs.
Рекомендуется
Battery-Powered Sensor Nodes
The PIC18F45J10T-I/ML is well suited to battery-powered sensor nodes because its nanoWatt power-management modes let the core drop to microamp-level currents between measurements, while the integrated 10-bit 13-channel ADC reads thermistors, photocells, and battery voltage without external parts. The 2.0 V-3.6 V supply range operates directly from two alkaline or one Li-ion cell, and the 1 KB SRAM plus 32 KB Flash is enough for averaging algorithms, calibration tables, and a small packet buffer for the enhanced USART. Designers typically wake the MCU on a Timer1 overflow, sample the ADC, run a moving-average filter, transmit on the USART, and return to sleep - extending coin-cell life to years. The 44-QFN ML package saves board area vs TQFP, important for compact wireless sensor bricks.
Рекомендуется
Industrial Control Front Ends
The PIC18F45J10T-I/ML serves as an industrial control front end because its 10-bit 13-channel ADC handles multiple 4-20 mA or 0-10 V analog inputs simultaneously, while the enhanced USART (with LIN) connects to a master PLC or HMI panel over RS-485 or LIN. The 40 MHz core runs Modbus RTU framing and PID calculations within the 1 ms scan budget typical of small PLCs, and the 32 KB Flash comfortably holds ladder-logic interpreters, fault diagnostics, and lookup tables for linearization. The -40 C to +85 C industrial temperature range plus the 44-QFN ML footprint with exposed thermal pad supports factory-floor enclosures. Two MSSP ports handle SPI-to-isolated digital I/O and I2C-to-RTC plus EEPROM on a single bus.
Рекомендуется
Low-Speed Motor Control BLDC/PMSM Front Ends
The PIC18F45J10T-I/ML works as a low-speed motor-control front end because its enhanced USART with LIN can be paired with a dedicated BLDC/PMSM gate-driver or dsPIC, offloading commutation timing while this MCU handles user input, RPM setpoint, and serial diagnostics. The 10-bit ADC samples back-EMF or current-sense signals, and the four timers (Timer0-3) provide PWM and quadrature-decoder functionality for small pumps, fans, and e-bike throttles. The 2.0 V-3.6 V supply and 40 MHz core balance cost and performance for sub-100 W motor control where a full dsPIC would be overkill. The 44-QFN ML exposed thermal pad handles the modest dissipation of an MCU front end.
Рекомендуется
HVAC Climate Sensor Modules
The PIC18F45J10T-I/ML is appropriate for HVAC climate-sensor modules because its nanoWatt sleep modes plus 13-channel ADC let it cycle between temperature, humidity, and CO2 analog sensors while drawing microamps in standby, suitable for battery or Energy-Harvest powered wireless thermostats. The enhanced USART with LIN hardware attaches to the HVAC blower and damper actuators over the LIN bus, a standard in residential HVAC control. The 32 KB Flash holds compensation curves for NTC thermistors and SHT-style humidity sensors, while 1 KB SRAM buffers multi-sensor readings. Operating from 2.0 V-3.6 V supports direct 2xAA battery operation. The 44-QFN ML exposed thermal pad is helpful when the MCU sits near a warm supply rail.
Рекомендуется
Low-Cost Lighting Controllers (DMX/DALI Slave)
The PIC18F45J10T-I/ML fits low-cost DMX-512 or DALI slave lighting controllers because its enhanced USART runs DMX at 250 kbaud with break detection in hardware, offloading the protocol from firmware. The two MSSP ports can handle DALI on one channel (via external transceiver) and SPI-to-LED-driver on the other. The 10-bit ADC reads ambient-light sensors for daylight harvesting, and 32 KB Flash accommodates dimming curves, scene memory, and fault logging. The 2.0 V-3.6 V supply and 44-QFN ML compact footprint fit inside inline LED fixtures and junction-box modules. PWM outputs on Timer2/3 drive analog dimming FETs without extra glue logic.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC18F45J10T-I/ML — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC18F45J10-I/ML | PIC18F45K22-I/ML | PIC18F45K22T-I/ML | PIC18F44J10T-I/ML |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-QFN (8x8 mm) ML | 44-QFN (8x8 mm) ML - same | 44-QFN (8x8 mm) ML - same | 44-QFN (8x8 mm) ML - same | 44-QFN (8x8 mm) ML - same |
| Maximum Clock | 40 MHz | 40 MHz | 64 MHz (+60%) | 64 MHz (+60%) | 40 MHz |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 16 KB (-50%) |
| SRAM | 1 KB | 1 KB | 1.5 KB (+50%) | 1.5 KB (+50%) | 1 KB |
| Supply Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 1.8 V to 5.5 V (wider) | 1.8 V to 5.5 V (wider) | 2.0 V to 3.6 V |
| ADC Channels | 13 channels (10-bit) | 13 channels | 14 channels (+1) | 14 channels (+1) | 13 channels |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Packaging | Tape & Reel | Tray | Tray | Tape & Reel | Tape & Reel |
Ключевые отличия
- Drop-in tape-and-reel variant of the same PIC18F45J10 die (против PIC18F45J10-I/ML)
- Lower cost than K-series in identical 44-QFN ML footprint (против PIC18F45K22-I/ML)
- More Flash than the smaller J10 sibling in same 44-QFN ML (против PIC18F44J10T-I/ML)
Заметки по проектированию
PIC18F45J10T-I/ML must operate from 2.0 V to 3.6 V only; supplying 5 V damages the part because the J-series is a 3.3 V-only family. For 5 V systems migrating from PIC18F452, add a 3.3 V LDO (e.g. MCP1700) on the VDD pins. The MCU has three VDD/VSS pairs (VDD1/VDD2/VDD3 plus pins 10, 20, 30); tie them together at the IC and decouple each with a 100 nF ceramic placed within 5 mm of the pin. The internal 2.5 V regulator output (VDDCORE, pin 43) must be decoupled with a 1-10 uF low-ESR capacitor; omitting it causes core instability and erratic code execution under load.
The 44-QFN ML package uses an exposed thermal pad (EP) on the underside that must be soldered to a copper pour of at least 25 mm x 25 mm on the top or inner PCB layer. With the EP connected to ground, the package's thermal resistance (theta_JA) drops from ~50 C/W (no EP) to roughly 20 C/W, keeping junction temperature well below 125 C at 40 MHz across the -40 C to +85 C ambient range. Vias in the EP copper pour (8-12 thermal vias, 0.3 mm drill) are recommended to spread heat to inner/bottom layers. Estimating: at 25 C ambient, 40 MHz, 3.3 V, the J10 draws ~15 mA active -> 50 mW dissipation; with 25 mm copper pad this stays under 30 C rise.
Keep the ICSP clock and data traces (RB6/PGC, RB7/PGD) short and away from switching signals. The MCLR line needs a 10 kohm pull-up to VDD plus a 100 nF cap to ground for clean reset; if an in-circuit programmer is also used, the MCLR pull-up should be at least 10 kohm to avoid contention with the programmer's VPP drive. Place the 0.1 uF decoupling caps as close as possible to each VDD/VSS pair, with the 1-10 uF VDDCORE cap right next to pin 43. Avoid routing analog inputs (ANx) next to high-frequency digital lines like SCK or PWM outputs to minimize ADC noise coupling.
Three common pitfalls: (1) supplying 5 V destroys the J-series - always verify VDD is 2.0 V-3.6 V before applying power; (2) forgetting the VDDCORE decoupling capacitor on pin 43 causes mysterious resets and erratic Flash write/erase - the cap is required, not optional; (3) tying MCLR directly to VDD without the 10 kohm pull-up makes the MCU sensitive to EMI-induced resets on long cable harnesses. Also note the J10 has no on-chip EEPROM - use program-Flash with wear-leveling or attach an external I2C EEPROM (e.g. 24LC256) for non-volatile data storage.
Информация о соответствии
RoHS compliant per Microchip product page; lead-free and halogen-free per Microchip packaging materials declaration. Not AEC-Q100 qualified - for automotive LIN body modules use AEC-Q100 qualified PIC18F variants such as PIC18F46K22-I/PT family.
