PIC18F66K22T-I/MR - 8-bit 64MHz MCU 64KB Flash | Microchip
Артикул: PIC18F66K22T-I/MR ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.5 | $6,50 |
| 10 | $6.1 | $61,00 |
| 100 | $5.4 | $540,00 |
| 500 | $4.95 | $2.475,00 |
| 1.000 | $4.5 | $4.500,00 |
| 3.300 | $4.2 | $13.860,00 |
PIC18F66K22T-I/MR Обзор
A PIC microcontroller (Programmable Interface Controller) is a Harvard-architecture, RISC-based microcontroller that integrates a CPU, non-volatile Flash program memory, working RAM, EEPROM, and a rich peripheral set into a single IC. Microchip's PIC18 family extends the baseline PIC16 instruction set with linear memory addressing and C-friendly extensions, sitting between the 8-bit PIC16 and the 16-bit dsPIC/PIC24 families in the broader microcontroller taxonomy: 8-bit MCU -> PIC18 -> nanoWatt XLP family -> low-power 8-bit PIC microcontroller.
Key features of this part include nanoWatt eXtreme Low Power (XLP) technology with deep-sleep currents in the nanoamp range, a 12-bit A/D converter with up to 16 channels, two I2C, two SPI and two USART (LIN-capable) interfaces, the Charge Time Measurement Unit (CTMU) for capacitive touch and simple time-of-flight sensing, and a Parallel Slave Port for external bus expansion. The 64-pin VQFN gives access to the full peripheral count of the PIC18F6xK22 sub-family.
The PIC18F66K22 architecture uses a modified Harvard core with a 16-bit instruction word and 8-bit data path. A 31-level hardware stack, indexed and indirect addressing modes, and an 8x8 hardware multiply support efficient C compilation. Internal oscillator blocks can be software-tuned, and the PLL derives the 64 MHz FOSC from a lower-frequency source, enabling both low-power sleep operation and high-throughput active modes. The CTMU is a programmable constant-current source that, combined with the A/D, performs capacitance measurement for touch keys or simple distance sensing.
Typical applications include industrial control panels, capacitive touch human-machine interfaces, low-power remote sensor nodes, battery-powered instrumentation, USB/serial bridging using the USART peripherals, and small graphical or segment-display user interfaces. The wide peripheral mix also suits HVAC controllers and home appliances where multiple communication buses and ADC channels must coexist on a single chip.
When designing with this device, allocate the VQFN exposed pad (EP) to a solid ground copper pour for thermal dissipation, and follow Microchip's decoupling guidance of a 100 nF ceramic on every VDD/AVDD pair plus a bulk 10 uF near the IC. Programming is supported via ICSP on PGC/PGD, and Microchip's MPLAB X with XC8 provides the canonical toolchain.
This page synthesizes distributor pricing, drop-in alternatives from the PIC18 K-series, and practical design notes not collected in any single distributor listing.
Аналоги без доработки для PIC18F66K22T-I/MR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC18F66K22T-I/MR (тот же форм-фактор и посадочное место) — отличается по Package, Core Architecture, I/O Pins, ADC, Operating Temperature.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC18F66K22-I/MRRSL
✅ Прямая замена✓ В наличии
$3.55 / шт.
Открыть даташит →PIC18F66K22T-E/MR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC18F65K22T-I/MR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC18F65K22T-E/MR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC18F66K22T-I/MR Максимальные параметры и электрические характеристики
| Core Architecture | PIC18 (8-bit RISC, Harvard) |
| Maximum CPU Frequency | 64 MHz (16 MIPS at 64 MHz) |
| Program Memory (Flash) | 64 KB |
| SRAM | 4 KB |
| Data EEPROM | 1 KB |
| Корпус | 64-pin VQFN (9x9 mm) |
| Operating Voltage Range | 1.8 V to 5.5 V |
| Диапазон рабочих температур | -40 C to +85 C (Industrial) |
| I/O Pins | 53 (approximate, varies by peripheral remap) |
| ADC | 12-bit, up to 16 channels |
| Comparators | 3 |
| PWM Outputs | Up to 5 CCP / 3 ECCP |
| Communication Interfaces | 2x I2C, 2x SPI, 2x USART (LIN), Parallel Slave Port |
| Special Features | nanoWatt XLP, CTMU, internal oscillator, PLL, ICSP |
| Тип монтажа | Surface Mount |
| Уровень MSL | 3 |
| Статус RoHS | Compliant |
| Programming Interface | ICSP (PGC/PGD) |
Конфигурация выводов PIC18F66K22T-I/MR
| Контакт 1 | RA0/AN0/C1IN0 — PORTA bit 0 / analog input / comparator 1 input |
| Контакт 2 | RA1/AN1/C2IN1 — PORTA bit 1 / analog input / comparator input |
| Контакт 3 | RA2/AN2/C2IN2 — PORTA bit 2 / analog input / comparator input |
| Контакт 4 | RA3/AN3/C1IN1 — PORTA bit 3 / analog input / comparator input |
| Контакт 5 | RA4/AN4/C1OUT — PORTA bit 4 / analog input / comparator 1 output |
| Контакт 6 | RA5/AN5/C2OUT — PORTA bit 5 / analog input / comparator 2 output |
| Контакт 7 | RA6/OSC2 — PORTA bit 6 / crystal oscillator output |
| Контакт 8 | RA7/OSC1 — PORTA bit 7 / crystal oscillator input |
| Контакт 9 | VDD — Digital supply voltage |
| Контакт 10 | VSS — Digital ground |
| Контакт 11 | RB0/AN12/INT0 — PORTB bit 0 / analog / external interrupt 0 |
| Контакт 12 | RB1/AN10/INT1 — PORTB bit 1 / analog / external interrupt 1 |
| Контакт 13 | RB2/AN8 — PORTB bit 2 / analog input |
| Контакт 14 | RB3/AN9 — PORTB bit 3 / analog input |
| Контакт 15 | RB4/AN11 — PORTB bit 4 / analog input |
| Контакт 16 | RB5/AN13 — PORTB bit 5 / analog input |
| Контакт 17 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Контакт 18 | RB7/PGD — PORTB bit 7 / ICSP data |
| Контакт 19 | RC0 — PORTC bit 0 |
| Контакт 20 | RC1 — PORTC bit 1 |
| Контакт 21 | RC2 — PORTC bit 2 |
| Контакт 22 | RC3 — PORTC bit 3 |
| Контакт 23 | RC4 — PORTC bit 4 |
| Контакт 24 | RC5 — PORTC bit 5 |
| Контакт 25 | RC6 — PORTC bit 6 |
| Контакт 26 | RC7 — PORTC bit 7 |
| Контакт 27 | RD0 — PORTD bit 0 |
| Контакт 28 | RD1 — PORTD bit 1 |
| Контакт 29 | RD2 — PORTD bit 2 |
| Контакт 30 | RD3 — PORTD bit 3 |
| Контакт 31 | RD4 — PORTD bit 4 |
| Контакт 32 | RD5 — PORTD bit 5 |
| Контакт 33 | RD6 — PORTD bit 6 |
| Контакт 34 | RD7 — PORTD bit 7 |
| Контакт 35 | RE0 — PORTE bit 0 |
| Контакт 36 | RE1 — PORTE bit 1 |
| Контакт 37 | RE2 — PORTE bit 2 |
| Контакт 38 | RE3 — PORTE bit 3 (often MCLR) |
| Контакт 39 | RE4 — PORTE bit 4 |
| Контакт 40 | RE5 — PORTE bit 5 |
| Контакт 41 | RE6 — PORTE bit 6 |
| Контакт 42 | RE7 — PORTE bit 7 |
| Контакт 43 | RF0 — PORTF bit 0 |
| Контакт 44 | RF1 — PORTF bit 1 |
| Контакт 45 | RF2 — PORTF bit 2 |
| Контакт 46 | RF3 — PORTF bit 3 |
| Контакт 47 | RF4 — PORTF bit 4 |
| Контакт 48 | RF5 — PORTF bit 5 |
| Контакт 49 | RF6 — PORTF bit 6 |
| Контакт 50 | RF7 — PORTF bit 7 |
| Контакт 51 | RG0 — PORTG bit 0 |
| Контакт 52 | RG1 — PORTG bit 1 |
| Контакт 53 | RG2 — PORTG bit 2 |
| Контакт 54 | RG3 — PORTG bit 3 |
| Контакт 55 | RG4 — PORTG bit 4 |
| Контакт 56 | AVDD — Analog supply voltage |
| Контакт 57 | AVSS — Analog ground |
| Контакт 58 | RH0 — PORTH bit 0 |
| Контакт 59 | RH1 — PORTH bit 1 |
| Контакт 60 | RH2 — PORTH bit 2 |
| Контакт 61 | RH3 — PORTH bit 3 |
| Контакт 62 | RH4 — PORTH bit 4 |
| Контакт 63 | RH5 — PORTH bit 5 |
| Контакт 64 | RH6 — PORTH bit 6 |
| Контакт EP | EP — Exposed thermal pad - connect to ground |
Типичное применение
PIC18F66K22T-I/MR подходит для 6 применениеs: Industrial Control Panels, Capacitive Touch HMI, Battery-Powered Remote Sensor Nodes, HVAC and Home Appliance Controllers, USB/Serial Bridging Adapters, Low-Cost Graphical Segment Displays.
Industrial Control Panels
The PIC18F66K22T-I/MR fits industrial control panels where multiple communication buses and ADC channels must coexist on a single low-power MCU. Its 53 I/O lines drive relay drivers, status LEDs, key-matrix inputs, and segment or character displays, while two USARTs (LIN-capable) and two SPI/I2C peripherals connect to sensor daughterboards and a host PLC. The 12-bit ADC with up to 16 channels samples 4-20 mA loop currents and thermistor bridges directly, eliminating an external AFE. nanoWatt XLP deep-sleep at sub-microamp currents lets the panel retain network polling for years on a single coin cell, and the industrial -40C to +85C rating covers factory floor environments. Programming via ICSP supports in-field firmware updates through the HMI.
Рекомендуется
Capacitive Touch HMI
The PIC18F66K22T-I/MR is well suited for capacitive touch human-machine interfaces because of its on-chip CTMU (Charge Time Measurement Unit). The CTMU sources a programmable constant current into a touch electrode and the resulting voltage rise time is measured by the 12-bit ADC, producing stable touch-decision readings without an external touch controller IC. Up to 16+ electrodes can be scanned sequentially, supporting sliders and wheels on appliances, kitchen equipment, and consumer electronics. The nanoWatt XLP feature set keeps idle touch-scan current below 5 uA, and the 64-pin VQFN exposes enough I/O for backlight PWM, buzzer drive, and an I2C/SPI display interface alongside the touch matrix.
Рекомендуется
Battery-Powered Remote Sensor Nodes
Battery-powered remote sensor nodes benefit from the PIC18F66K22T-I/MR's nanoWatt XLP technology, which delivers deep-sleep currents in the tens of nanoamps while retaining RAM and brown-out reset. The MCU wakes periodically, samples its 12-bit ADC, transmits via one of the two USART or SPI peripherals, and returns to sleep, achieving multi-year coin-cell life in metering and environmental monitoring. The 1.8 V to 5.5 V operating range covers both single-cell Li-ion and 3.6 V Li-SOCl2 chemistries without level shifting. The 64-pin VQFN integrates the full peripheral set, including the CTMU, so a single chip performs capacitance, voltage, and temperature sensing plus RF/transceiver control.
Рекомендуется
HVAC and Home Appliance Controllers
HVAC and home appliance controllers use the PIC18F66K22T-I/MR to drive triac-controlled AC loads, read thermistor temperature sensors, run BLDC or stepper fans, and communicate on LIN or RS-485 fieldbuses. The MCU's three analog comparators support zero-cross detection for triac phase-angle firing, while its CCP/ECCP modules generate the PWM signals for variable-speed fans and valves. Two LIN-capable USARTs interface to the appliance's master controller and to user-interface subassemblies, and the 1 KB data EEPROM stores user-setpoint history across power cycles. The industrial temperature grade covers refrigerator, oven, and boiler compartments reliably.
Рекомендуется
USB/Serial Bridging Adapters
USB-to-serial bridging adapters use the PIC18F66K22T-I/MR as the bridge MCU, leveraging its two USARTs to convert between legacy RS-232/RS-485 links and a USB host through an external transceiver or software USB bit-banging. The 64 KB Flash accommodates dual CDC class drivers, and 4 KB SRAM buffers UART-to-USB traffic without flow-control stalls. The two SPI peripherals simultaneously drive an SD card or external flash for logging, while the I2C bus interfaces to EEPROM or RTC. The 64-pin VQFN exposes enough I/O for status LEDs, push-buttons, and configuration DIP switches alongside the bridge functions, and the industrial temperature grade covers outdoor enclosures.
Рекомендуется
Low-Cost Graphical Segment Displays
Low-cost graphical segment and small TFT displays are driven by the PIC18F66K22T-I/MR, using its two SPI channels to update a graphics controller or segment LCD driver at high refresh rates. The CCP/ECCP modules generate backlight PWM with 10-bit resolution for smooth dimming, and the 12-bit ADC reads ambient-light sensors for automatic brightness control. The CTMU enables front-panel capacitive keys behind a glass overlay. With 64 KB Flash and 4 KB SRAM, the MCU holds complete UI state machines and bitmaps for small QVGA displays, eliminating an external graphics controller and reducing BOM cost in consumer appliances.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC18F66K22T-I/MR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC18F66K22-I/MR | PIC18F66K22T-E/MR | PIC18F65K22T-I/MR | PIC18F65K22T-E/MR |
|---|---|---|---|---|---|
| Package | 64-pin VQFN (9x9 mm) | 64-pin VQFN (9x9 mm) - same | 64-pin VQFN (9x9 mm) - same | 64-pin VQFN (9x9 mm) - same | 64-pin VQFN (9x9 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (Flash) | 64 KB | 64 KB | 64 KB | 32 KB (-50%) | 32 KB (-50%) |
| Maximum Frequency | 64 MHz | 64 MHz | 64 MHz | 64 MHz | 64 MHz |
| SRAM | 4 KB | 4 KB | 4 KB | 2 KB (-50%) | 2 KB (-50%) |
| Data EEPROM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +125C (Extended) | -40C to +85C (Industrial) | -40C to +125C (Extended) |
| Packaging | Tape & Reel | Tray | Tape & Reel | Tape & Reel | Tape & Reel |
| Pin Compatibility | 64-pin VQFN (reference) | 100% drop-in | 100% drop-in | Footprint-compatible, I/O count reduced | Footprint-compatible, I/O count reduced |
Ключевые отличия
- Tape-and-reel packaging for high-volume SMT assembly (против PIC18F66K22-I/MR)
- Industrial vs extended temperature grade flexibility (против PIC18F66K22T-E/MR)
- Larger Flash and RAM vs K22 sibling (против PIC18F65K22T-I/MR)
- On-chip CTMU eliminates external touch controller (против External capacitive touch IC designs)
Заметки по проектированию
The VQFN-64 (9x9 mm) package has an exposed thermal pad (EP) that MUST be soldered to a ground copper pour for mechanical reliability and thermal dissipation. Per Microchip application note AN246, the EP should connect to a ground plane with at least 16 thermal vias on a 0.5-1.0 mm grid. Place a 100 nF ceramic decoupling capacitor within 2 mm of every VDD and AVDD pin, plus a 10 uF bulk capacitor near the MCU. Keep the EP-to-VDD capacitance under 5 pF to avoid injected switching noise into the analog rail.
When designing nanoWatt XLP low-power applications, follow Microchip AN1307 and configure the unused peripherals to their lowest-power idle states. The PIC18F66K22T-I/MR's deep-sleep current is in the tens of nanoamps with RTCC and WDT enabled; however, leaving the ADC, comparators, or CTMU powered in sleep raises this by tens of microamps. Use the PMD (Peripheral Module Disable) registers to gate each unused peripheral's clock. Estimate (assuming IDD = 30 nA in deep sleep with RTCC, 3 V battery, 2000 mAh capacity): 2000 mAh / (30 nA * 24 h / 1e9) = approximately 2,740 years theoretical life - real-world is bounded by battery shelf life (~10 years).
Common pitfalls when bringing up the PIC18F66K22T-I/MR include: (1) forgetting to configure CONFIG words for the internal oscillator or external crystal before code execution, leaving the MCU running off the uncalibrated FRC at 4 MHz; (2) enabling the PLL with an incompatible clock source, causing the FOSC to exceed 64 MHz and triggering a brown-out; (3) assigning analog functions to pins that are remapped by the PPS (Peripheral Pin Select) module without unlocking IOLOCK; and (4) sharing ICSP lines (PGC/PGD on RB6/RB7) with external pull-ups that exceed 10 kohm, which prevents in-circuit programming. Always read CONFIG settings into MPLAB X before debugging.
Place the ICSP connector (PGC/PGD/RESET/VPP/GND) at the board edge for in-circuit programming access, with each signal routed within 100 mm of the MCU. Keep analog inputs (AN0-AN15) physically separated from digital switching traces, with the AVSS pin returning to a quiet ground island joined to the digital ground at a single point. For capacitive-touch PCB layouts, use Microchip AN1258: route each electrode with a hatched or solid guard ring driven by the same CTMU current source return to suppress stray capacitance, and ensure the touch electrode's ground reference is the local chassis, not earth.
Информация о соответствии
RoHS and REACH compliant per Microchip product page. Industrial temperature grade; not AEC-Q100 qualified - use PIC18F66K22-E/MR series for AEC-Q100 automotive requirements. Lead-free and halogen-free per Microchip Material Declaration.
