PIC18F86J55T-I/PT - 96KB Flash USB MCU 8-Bit 48MHz TQFP-80
Артикул: PIC18F86J55T-I/PT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $9.1 | $9,10 |
| 10 | $8.2 | $82,00 |
| 100 | $7.35 | $735,00 |
| 500 | $6.6 | $3.300,00 |
| 1.000 | $5.95 | $5.950,00 |
PIC18F86J55T-I/PT Обзор
A microcontroller (MCU) is an integrated circuit containing a CPU, memory, and programmable peripherals. The PIC18J family is built on an enhanced Harvard architecture with a RISC-style instruction set, providing deterministic interrupt response and single-cycle instruction execution for embedded control. MCUs sit at the lowest tier of the embedded processor hierarchy - above simple logic ICs, below microprocessors - and are the workhorse components for almost every connected product today.
Key specifications include 4KB of buffer RAM used by the USB endpoint system, 66 general-purpose digital I/O pins, two analog comparators, a 10-bit ADC with up to 16 input channels, two CCP/ECCP modules, two EUSART ports (LIN-capable), one MSSP port that supports both SPI (up to 10 Mbit/s) and I2C, and an internal 31 kHz to 8 MHz oscillator block. The device integrates a charge time measurement unit (CTMU) for capacitive touch and a real-time clock calendar with on-chip 32 kHz oscillator support.
Architecturally, the PIC18F86J55 uses a wide 16-bit instruction path with separate program and data buses, allowing single-cycle fetches even while accessing data memory. The on-chip USB 2.0 Full-Speed transceiver eliminates the need for an external PHY, and the 4KB dedicated buffer RAM ensures USB throughput without starving user RAM. The nanoWatt features include Idle, Sleep, and deep-sleep modes with current as low as nanoampere-class levels when peripherals are gated off individually.
Typical applications include USB peripherals such as HID input devices and CDC serial bridges, embedded web and sensor interfaces with USB charging, industrial data loggers, automotive body controllers (LIN/J2602 nodes), home automation gateways, and low-power instrumentation with capacitive touch user interfaces. The wide 2.0V to 3.6V range also makes it suitable for single-cell Li-ion powered designs.
When designing with this part, plan the power-rail decoupling carefully: place a 100 nF ceramic on every VDD/AVDD pair, keep the USB D+/D- traces length-matched within 2 mm, and route the 48 MHz crystal traces short and guarded. The USB pull-up resistor on D+ must be enabled in firmware for proper enumeration. For low-power Sleep mode, gate off unused peripherals and use the RTCC with its dedicated 32 kHz crystal for sub-microamp standby.
This page synthesizes distributor pricing, parametric drop-in alternatives within the same 80-TQFP footprint, and practical design notes that complement - and extend - the information found in the manufacturer datasheet.
Аналоги без доработки для PIC18F86J55T-I/PT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC18F86J55T-I/PT (тот же форм-фактор и посадочное место) — отличается по ADC, Package, Operating Temperature, MSL Level, Core.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC18F86J55-I/PT
✅ Прямая замена✓ В наличии
$6.95 / шт.
Открыть даташит →PIC18F86J50T-I/PT
✅ Прямая замена✓ В наличии
$5.74 / шт.
Открыть даташит →PIC18F86J15T-I/PT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC18F86J10T-I/PT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC18F85J94-I/PT
✅ Прямая замена✓ В наличии
$4.85 / шт.
Открыть даташит →PIC18F86J15-I/PT
✅ Прямая замена✓ В наличии
$5.32 / шт.
Открыть даташит →PIC18F86J55T-I/PT Максимальные параметры и электрические характеристики
| Core | PIC18J, 8-bit |
| CPU Family | PIC 18J Microcontroller |
| Maximum Clock Speed | 48 MHz (12 MIPS) |
| Program Memory (Flash) | 96 KB (48K x 16) |
| Data RAM | 3.8 KB |
| USB Buffer RAM | 4 KB dedicated |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| I/O Pins | 66 |
| ADC | 10-bit, up to 16 channels |
| Comparators | 2 analog comparators |
| USB | USB 2.0 Full-Speed (12 Mbit/s), on-chip transceiver |
| EUSART | 2 (LIN-capable) |
| MSSP (SPI / I2C) | 1 (SPI up to 10 Mbit/s, I2C) |
| CCP / ECCP | 2 (CCP + ECCP) |
| CTMU (Capacitive Touch) | Yes |
| RTCC | Yes, with on-chip 32 kHz oscillator support |
| Рабочая температура | -40C to +85C (Industrial, 'I') |
| Корпус | 80-TQFP (PT) 12x12 mm |
| Тип монтажа | Surface Mount |
| Уровень MSL | 3 (168 hours) |
| Статус RoHS | Compliant |
| Lead-Free | Yes |
| Lifecycle | Active (PIC18J family with nanoWatt technology) |
Конфигурация выводов PIC18F86J55T-I/PT
| Контакт 1 | RE3/MCLR — Digital I/O / Master Clear (Reset) input with weak pull-up |
| Контакт 2 | RG0 — Digital I/O port G bit 0 |
| Контакт 3 | RG1 — Digital I/O port G bit 1 |
| Контакт 4 | RG2 — Digital I/O port G bit 2 |
| Контакт 5 | RG3 — Digital I/O port G bit 3 |
| Контакт 6 | RG4 — Digital I/O port G bit 4 |
| Контакт 7 | RA0/AN0 — Digital I/O / analog input 0 |
| Контакт 8 | RA1/AN1 — Digital I/O / analog input 1 |
| Контакт 9 | RA2/AN2 — Digital I/O / analog input 2 |
| Контакт 10 | RA3/AN3 — Digital I/O / analog input 3 |
| Контакт 11 | RA4/AN4/T0CKI — Digital I/O / analog input 4 / Timer0 clock input |
| Контакт 12 | RA5/AN5/SS1 — Digital I/O / analog input 5 / SPI1 slave select |
| Контакт 13 | VSS — Ground reference |
| Контакт 14 | VDD — Positive supply (2.0V to 3.6V) |
| Контакт 15 | RA6/OSC2 — Digital I/O / primary oscillator output |
| Контакт 16 | RA7/OSC1 — Digital I/O / primary oscillator input |
| Контакт 17 | RF0 — Digital I/O port F bit 0 |
| Контакт 18 | RF1 — Digital I/O port F bit 1 |
| Контакт 19 | RF2 — Digital I/O port F bit 2 |
| Контакт 20 | RF3 — Digital I/O port F bit 3 |
| Контакт 21 | RF4 — Digital I/O port F bit 4 |
| Контакт 22 | RF5 — Digital I/O port F bit 5 |
| Контакт 23 | RF6 — Digital I/O port F bit 6 |
| Контакт 24 | RF7 — Digital I/O port F bit 7 |
| Контакт 25 | VSS — Ground reference |
| Контакт 26 | VDD — Positive supply |
| Контакт 27 | RB0/INT0 — Digital I/O / external interrupt 0 |
| Контакт 28 | RB1/INT1 — Digital I/O / external interrupt 1 |
| Контакт 29 | RB2/INT2 — Digital I/O / external interrupt 2 |
| Контакт 30 | RB3/INT3 — Digital I/O / external interrupt 3 |
| Контакт 31 | RB4/KBI0 — Digital I/O / interrupt-on-change bit 0 |
| Контакт 32 | RB5/KBI1 — Digital I/O / interrupt-on-change bit 1 |
| Контакт 33 | RB6/KBI2/PGC — Digital I/O / ICSP clock |
| Контакт 34 | RB7/KBI3/PGD — Digital I/O / ICSP data |
| Контакт 35 | RC0 — Digital I/O port C bit 0 |
| Контакт 36 | RC1 — Digital I/O port C bit 1 |
| Контакт 37 | RC2 — Digital I/O port C bit 2 |
| Контакт 38 | RC3 — Digital I/O port C bit 3 |
| Контакт 39 | RC4 — Digital I/O port C bit 4 |
| Контакт 40 | RC5 — Digital I/O port C bit 5 |
| Контакт 41 | RC6 — Digital I/O port C bit 6 |
| Контакт 42 | RC7 — Digital I/O port C bit 7 |
| Контакт 43 | VSS — Ground reference |
| Контакт 44 | VDD — Positive supply |
| Контакт 45 | RD0 — Digital I/O port D bit 0 |
| Контакт 46 | RD1 — Digital I/O port D bit 1 |
| Контакт 47 | RD2 — Digital I/O port D bit 2 |
| Контакт 48 | RD3 — Digital I/O port D bit 3 |
| Контакт 49 | RD4 — Digital I/O port D bit 4 |
| Контакт 50 | RD5 — Digital I/O port D bit 5 |
| Контакт 51 | RD6 — Digital I/O port D bit 6 |
| Контакт 52 | RD7 — Digital I/O port D bit 7 |
| Контакт 53 | VSS — Ground reference |
| Контакт 54 | VDD — Positive supply |
| Контакт 55 | RE0 — Digital I/O port E bit 0 |
| Контакт 56 | RE1 — Digital I/O port E bit 1 |
| Контакт 57 | RE2 — Digital I/O port E bit 2 |
| Контакт 58 | VSS — Ground reference |
| Контакт 59 | VDD — Positive supply |
| Контакт 60 | RH0 — Digital I/O port H bit 0 |
| Контакт 61 | RH1 — Digital I/O port H bit 1 |
| Контакт 62 | RH2 — Digital I/O port H bit 2 |
| Контакт 63 | RH3 — Digital I/O port H bit 3 |
| Контакт 64 | RH4 — Digital I/O port H bit 4 |
| Контакт 65 | RH5 — Digital I/O port H bit 5 |
| Контакт 66 | RH6 — Digital I/O port H bit 6 |
| Контакт 67 | RH7 — Digital I/O port H bit 7 |
| Контакт 68 | RJ0 — Digital I/O port J bit 0 |
| Контакт 69 | RJ1 — Digital I/O port J bit 1 |
| Контакт 70 | RJ2 — Digital I/O port J bit 2 |
| Контакт 71 | RJ3 — Digital I/O port J bit 3 |
| Контакт 72 | RJ4 — Digital I/O port J bit 4 |
| Контакт 73 | RJ5 — Digital I/O port J bit 5 |
| Контакт 74 | RJ6 — Digital I/O port J bit 6 |
| Контакт 75 | RJ7 — Digital I/O port J bit 7 |
| Контакт 76 | D- — USB Full-Speed data minus (USB 2.0) |
| Контакт 77 | D+ — USB Full-Speed data plus (USB 2.0) |
| Контакт 78 | VUSB — Internal USB 3.3V regulator output (bypass cap required) |
| Контакт 79 | AVSS — Analog ground reference |
| Контакт 80 | AVDD — Analog positive supply (2.0V to 3.6V) |
Типичное применение
PIC18F86J55T-I/PT подходит для 7 применениеs: USB HID Peripherals, USB CDC Serial Bridges, Capacitive Touch User Interfaces, Industrial Data Loggers, Automotive LIN/J2602 Nodes, Low-Power Sensor Hubs with USB Charging, Home Automation Gateways.
USB HID Peripherals
The PIC18F86J55T-I/PT's on-chip USB 2.0 Full-Speed transceiver and 4KB dedicated USB buffer RAM make it a strong fit for USB HID peripherals such as keyboards, mice, game controllers, custom HID devices, and industrial pendants. The integrated 3.3V regulator and D+ pull-up eliminate the need for an external PHY, allowing direct bus-powered USB operation from a 5V VBUS rail. Designers can use the free Microchip USB stack to enumerate as a HID device, with 96KB Flash accommodating descriptor tables plus application logic. Compared to a USB-capable part without dedicated RAM, the 4KB buffer here prevents endpoint starvation and supports higher polling rates for low-latency HID reporting.
Рекомендуется
USB CDC Serial Bridges
For USB-to-UART virtual COM port adapters, the PIC18F86J55T-I/PT's two EUSART ports (LIN-capable) pair naturally with the USB CDC class to provide dual serial-over-USB channels from a single chip. The 48MHz core (12 MIPS) easily handles USB bulk transfer, hardware flow control, and bridge logic without CPU loading. The wide 2.0V to 3.6V supply range simplifies integration with both 3.3V-only UART targets and 5V-tolerant buses. Compared to discrete bridges, this integrated approach allows custom VID/PID, manufacturer string descriptors, and on-the-fly firmware updates via the Flash self-programming feature.
Рекомендуется
Capacitive Touch User Interfaces
The PIC18F86J55T-I/PT integrates Microchip's Charge Time Measurement Unit (CTMU), which combined with the on-chip ADC and 66 GPIO pins supports robust capacitive touch sensing for sliders, wheels, buttons, and proximity sensors. The CTMU measures capacitance with sub-pF resolution using a constant current source and timing circuit, enabling reliable touch detection even through 3mm of plastic overlay. The 96KB Flash is sufficient for advanced touch libraries such as Microchip's mTouch, and the nanoWatt sleep modes keep standby current low in battery-powered remote controls. Compared to discrete touch controllers, this integrated approach saves board space and BOM cost.
Рекомендуется
Industrial Data Loggers
Industrial data loggers benefit from the PIC18F86J55T-I/PT's 10-bit ADC with up to 16 input channels, 96KB Flash for FAT file system libraries and ring buffers, and 3.8KB RAM for sample windows. The MSSP port supports SPI Flash or SD card storage at up to 10 Mbit/s, while the two EUSARTs allow simultaneous RS-485 Modbus slave operation and USB host download. The industrial -40C to +85C operating range and 2.0V to 3.6V supply accommodate 24V-bus powered designs with buck regulators. Compared to MCU+external USB-IF solutions, the integrated USB makes field data extraction via laptop trivial.
Рекомендуется
Automotive LIN/J2602 Nodes
The PIC18F86J55T-I/PT's two LIN-capable EUSARTs make it a drop-in choice for automotive body electronics where Local Interconnect Network (LIN) bus nodes are needed for door modules, seat controllers, and mirror adjusters. The 48MHz core runs the LIN 2.1 stack with cycle-budget margin, and the 96KB Flash accommodates the LIN API plus application code. Industrial-grade temperature (-40C to +85C) and automotive-qualified PIC18F variants share this pinout for tier-1 designs. Compared to dedicated LIN slaves, the dual EUSART allows a single MCU to act as both a LIN master gateway and a peripheral node.
Рекомендуется
Low-Power Sensor Hubs with USB Charging
Battery-powered sensor hubs that occasionally connect to a phone or charger benefit from the PIC18F86J55T-I/PT's nanoWatt technology suite, including Idle, Sleep, and deep-sleep modes that drop current to the microampere range. The 66 GPIO pins accept multiple sensor inputs via I2C or SPI, while the USB port enables both data sync and battery charging from a single connector. The RTCC with dedicated 32 kHz oscillator keeps wall-clock time during sleep for timestamping. Compared to BLE-only solutions, USB provides higher bandwidth and avoids the radio certification burden for short-range tethered products.
Рекомендуется
Home Automation Gateways
The PIC18F86J55T-I/PT serves as a compact home automation gateway node that bridges USB-host controllers to sub-GHz radios, Zigbee dongles, or sensor chains. With 96KB Flash, the device can host both a USB HID/CDC stack and an SPI-based radio driver, acting as a translator between a touchscreen panel and a wireless mesh. The two EUSARTs enable simultaneous RS-485 wall-switch networks and USB diagnostic channels. Compared to single-radio gateways, this dual-bus configuration simplifies field debugging by exposing Modbus traffic over a USB CDC virtual COM port in parallel.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC18F86J55T-I/PT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC18F86J55-I/PT | PIC18F86J50T-I/PT | PIC18F86J15T-I/PT | PIC18F86J10T-I/PT | PIC18F85J94-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-TQFP (PT) 12x12 mm | 80-TQFP (PT) - same | 80-TQFP (PT) - same | 80-TQFP (PT) - same | 80-TQFP (PT) - same | 80-TQFP (PT) - same |
| Flash Memory | 96 KB | 96 KB | 96 KB | 96 KB | 96 KB | 32 KB |
| Data RAM | 3.8 KB + 4 KB USB buffer | 3.8 KB + 4 KB USB buffer | 3.8 KB (no dedicated USB buffer) | 3.8 KB (no USB block) | 3.8 KB | 2 KB |
| USB 2.0 Full-Speed | Yes (on-chip transceiver + 4 KB buffer) | Yes | Yes (no dedicated buffer) | No | No | No |
| Maximum Clock | 48 MHz (12 MIPS) | 48 MHz | 48 MHz | 48 MHz | 40 MHz | 64 MHz |
| I/O Pins | 66 | 66 | 66 | 66 | 66 | 66 |
| Operating Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Approx. Qty-1000 Price (USD) | $5.95 | ~$5.95 | ~$6.20 | ~$5.40 | ~$4.80 | ~$5.20 |
Ключевые отличия
- On-chip USB 2.0 Full-Speed transceiver with dedicated 4 KB buffer RAM (против PIC18F86J50T-I/PT)
- USB-capable 80-TQFP PIC18J variant with full peripheral set (против PIC18F86J15T-I/PT)
- 48MHz core with 66 I/O pins at 80-TQFP (против PIC18F85J94-I/PT)
- Industrial-grade temperature range with nanoWatt low-power modes (против PIC18F86J10T-I/PT)
Заметки по проектированию
Estimated: at 48MHz CPU speed with all peripherals active, the PIC18F86J55T-I/PT draws roughly 25mA from a 3.3V supply, giving core power dissipation of approximately 82 mW. Decouple each VDD/VSS pair with a 100 nF X7R ceramic placed within 3mm of the pin; add a single 4.7uF bulk cap on the AVdd rail to support the ADC and USB 3.3V regulator transients. The on-chip VUSB regulator requires a 0.01uF bypass on the VUSB pin to meet USB Full-Speed signaling eye masks.
Keep the USB D+ and D- traces length-matched to within 2 mm and surrounded by a continuous ground pour on both sides of the PCB; route them on the top layer directly over an unbroken ground plane to maintain 90 ohm differential impedance (per USB 2.0 Full-Speed specification). Place the 48 MHz primary crystal within 6 mm of OSC1/OSC2 with short traces and a ground guard ring. Per the Microchip PIC18F86J55 hardware checklist, do not route high-frequency signals under the crystal traces.
Two common pitfalls when bringing up the PIC18F86J55T-I/PT: (1) forgetting to enable the internal USB pull-up on D+ in firmware - the device will not enumerate without it; (2) configuring the PLL without the correct CPUDIV divisor, which can lock up the core. Per Microchip AN679, always start with a conservative HS or INTIO clock and verify with the MPLAB Snap debugger before changing the PLL multiplier. Also note that USB Full-Speed operation requires Vdd at or above 3.0V.
For designs using the 10-bit ADC, route analog inputs (RA0-RA5, RB0-RB3) away from digital switching traces and place a small RC filter (typically 1k + 100pF) on each analog input to prevent crosstalk from adjacent digital lines. The AVdd supply should be driven from Vdd through a ferrite bead, and AVss must connect directly to the digital ground at a single point near the MCU. Per the Microchip PIC18F86J55 errata, the ADC may exhibit offset errors if the CTMU and ADC are active simultaneously without proper sequencing.
Информация о соответствии
RoHS compliant per Microchip product page; halogen-free status not explicitly stated in retrieved data. Not AEC-Q100 qualified - this is an industrial-grade part; AEC-Q100 qualified PIC18F variants exist in the same family for automotive.
