PIC18F86J55T-I/PT - 96KB Flash USB MCU 8-Bit 48MHz TQFP-80
Référence : PIC18F86J55T-I/PT ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $9.1 | $9,10 |
| 10 | $8.2 | $82,00 |
| 100 | $7.35 | $735,00 |
| 500 | $6.6 | $3 300,00 |
| 1 000 | $5.95 | $5 950,00 |
PIC18F86J55T-I/PT Présentation
A microcontroller (MCU) is an integrated circuit containing a CPU, memory, and programmable peripherals. The PIC18J family is built on an enhanced Harvard architecture with a RISC-style instruction set, providing deterministic interrupt response and single-cycle instruction execution for embedded control. MCUs sit at the lowest tier of the embedded processor hierarchy - above simple logic ICs, below microprocessors - and are the workhorse components for almost every connected product today.
Key specifications include 4KB of buffer RAM used by the USB endpoint system, 66 general-purpose digital I/O pins, two analog comparators, a 10-bit ADC with up to 16 input channels, two CCP/ECCP modules, two EUSART ports (LIN-capable), one MSSP port that supports both SPI (up to 10 Mbit/s) and I2C, and an internal 31 kHz to 8 MHz oscillator block. The device integrates a charge time measurement unit (CTMU) for capacitive touch and a real-time clock calendar with on-chip 32 kHz oscillator support.
Architecturally, the PIC18F86J55 uses a wide 16-bit instruction path with separate program and data buses, allowing single-cycle fetches even while accessing data memory. The on-chip USB 2.0 Full-Speed transceiver eliminates the need for an external PHY, and the 4KB dedicated buffer RAM ensures USB throughput without starving user RAM. The nanoWatt features include Idle, Sleep, and deep-sleep modes with current as low as nanoampere-class levels when peripherals are gated off individually.
Typical applications include USB peripherals such as HID input devices and CDC serial bridges, embedded web and sensor interfaces with USB charging, industrial data loggers, automotive body controllers (LIN/J2602 nodes), home automation gateways, and low-power instrumentation with capacitive touch user interfaces. The wide 2.0V to 3.6V range also makes it suitable for single-cell Li-ion powered designs.
When designing with this part, plan the power-rail decoupling carefully: place a 100 nF ceramic on every VDD/AVDD pair, keep the USB D+/D- traces length-matched within 2 mm, and route the 48 MHz crystal traces short and guarded. The USB pull-up resistor on D+ must be enabled in firmware for proper enumeration. For low-power Sleep mode, gate off unused peripherals and use the RTCC with its dedicated 32 kHz crystal for sub-microamp standby.
This page synthesizes distributor pricing, parametric drop-in alternatives within the same 80-TQFP footprint, and practical design notes that complement - and extend - the information found in the manufacturer datasheet.
Alternatives de remplacement direct pour PIC18F86J55T-I/PT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC18F86J55T-I/PT (même facteur de forme et même empreinte) — différant par ADC, Package, Operating Temperature, MSL Level, Core.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC18F86J55-I/PT
✅ Remplacement direct✓ En stock
$6.95 / unité
Voir la fiche technique →PIC18F86J50T-I/PT
✅ Remplacement direct✓ En stock
$5.74 / unité
Voir la fiche technique →PIC18F86J15T-I/PT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC18F86J10T-I/PT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC18F85J94-I/PT
✅ Remplacement direct✓ En stock
$4.85 / unité
Voir la fiche technique →PIC18F86J15-I/PT
✅ Remplacement direct✓ En stock
$5.32 / unité
Voir la fiche technique →PIC18F86J55T-I/PT Valeurs maximales et caractéristiques électriques
| Core | PIC18J, 8-bit |
| CPU Family | PIC 18J Microcontroller |
| Maximum Clock Speed | 48 MHz (12 MIPS) |
| Program Memory (Flash) | 96 KB (48K x 16) |
| Data RAM | 3.8 KB |
| USB Buffer RAM | 4 KB dedicated |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| I/O Pins | 66 |
| ADC | 10-bit, up to 16 channels |
| Comparators | 2 analog comparators |
| USB | USB 2.0 Full-Speed (12 Mbit/s), on-chip transceiver |
| EUSART | 2 (LIN-capable) |
| MSSP (SPI / I2C) | 1 (SPI up to 10 Mbit/s, I2C) |
| CCP / ECCP | 2 (CCP + ECCP) |
| CTMU (Capacitive Touch) | Yes |
| RTCC | Yes, with on-chip 32 kHz oscillator support |
| Température de fonctionnement | -40C to +85C (Industrial, 'I') |
| Boîtier | 80-TQFP (PT) 12x12 mm |
| Type de montage | Surface Mount |
| Niveau MSL | 3 (168 hours) |
| Statut RoHS | Compliant |
| Lead-Free | Yes |
| Lifecycle | Active (PIC18J family with nanoWatt technology) |
Configuration des broches de PIC18F86J55T-I/PT
| Broche 1 | RE3/MCLR — Digital I/O / Master Clear (Reset) input with weak pull-up |
| Broche 2 | RG0 — Digital I/O port G bit 0 |
| Broche 3 | RG1 — Digital I/O port G bit 1 |
| Broche 4 | RG2 — Digital I/O port G bit 2 |
| Broche 5 | RG3 — Digital I/O port G bit 3 |
| Broche 6 | RG4 — Digital I/O port G bit 4 |
| Broche 7 | RA0/AN0 — Digital I/O / analog input 0 |
| Broche 8 | RA1/AN1 — Digital I/O / analog input 1 |
| Broche 9 | RA2/AN2 — Digital I/O / analog input 2 |
| Broche 10 | RA3/AN3 — Digital I/O / analog input 3 |
| Broche 11 | RA4/AN4/T0CKI — Digital I/O / analog input 4 / Timer0 clock input |
| Broche 12 | RA5/AN5/SS1 — Digital I/O / analog input 5 / SPI1 slave select |
| Broche 13 | VSS — Ground reference |
| Broche 14 | VDD — Positive supply (2.0V to 3.6V) |
| Broche 15 | RA6/OSC2 — Digital I/O / primary oscillator output |
| Broche 16 | RA7/OSC1 — Digital I/O / primary oscillator input |
| Broche 17 | RF0 — Digital I/O port F bit 0 |
| Broche 18 | RF1 — Digital I/O port F bit 1 |
| Broche 19 | RF2 — Digital I/O port F bit 2 |
| Broche 20 | RF3 — Digital I/O port F bit 3 |
| Broche 21 | RF4 — Digital I/O port F bit 4 |
| Broche 22 | RF5 — Digital I/O port F bit 5 |
| Broche 23 | RF6 — Digital I/O port F bit 6 |
| Broche 24 | RF7 — Digital I/O port F bit 7 |
| Broche 25 | VSS — Ground reference |
| Broche 26 | VDD — Positive supply |
| Broche 27 | RB0/INT0 — Digital I/O / external interrupt 0 |
| Broche 28 | RB1/INT1 — Digital I/O / external interrupt 1 |
| Broche 29 | RB2/INT2 — Digital I/O / external interrupt 2 |
| Broche 30 | RB3/INT3 — Digital I/O / external interrupt 3 |
| Broche 31 | RB4/KBI0 — Digital I/O / interrupt-on-change bit 0 |
| Broche 32 | RB5/KBI1 — Digital I/O / interrupt-on-change bit 1 |
| Broche 33 | RB6/KBI2/PGC — Digital I/O / ICSP clock |
| Broche 34 | RB7/KBI3/PGD — Digital I/O / ICSP data |
| Broche 35 | RC0 — Digital I/O port C bit 0 |
| Broche 36 | RC1 — Digital I/O port C bit 1 |
| Broche 37 | RC2 — Digital I/O port C bit 2 |
| Broche 38 | RC3 — Digital I/O port C bit 3 |
| Broche 39 | RC4 — Digital I/O port C bit 4 |
| Broche 40 | RC5 — Digital I/O port C bit 5 |
| Broche 41 | RC6 — Digital I/O port C bit 6 |
| Broche 42 | RC7 — Digital I/O port C bit 7 |
| Broche 43 | VSS — Ground reference |
| Broche 44 | VDD — Positive supply |
| Broche 45 | RD0 — Digital I/O port D bit 0 |
| Broche 46 | RD1 — Digital I/O port D bit 1 |
| Broche 47 | RD2 — Digital I/O port D bit 2 |
| Broche 48 | RD3 — Digital I/O port D bit 3 |
| Broche 49 | RD4 — Digital I/O port D bit 4 |
| Broche 50 | RD5 — Digital I/O port D bit 5 |
| Broche 51 | RD6 — Digital I/O port D bit 6 |
| Broche 52 | RD7 — Digital I/O port D bit 7 |
| Broche 53 | VSS — Ground reference |
| Broche 54 | VDD — Positive supply |
| Broche 55 | RE0 — Digital I/O port E bit 0 |
| Broche 56 | RE1 — Digital I/O port E bit 1 |
| Broche 57 | RE2 — Digital I/O port E bit 2 |
| Broche 58 | VSS — Ground reference |
| Broche 59 | VDD — Positive supply |
| Broche 60 | RH0 — Digital I/O port H bit 0 |
| Broche 61 | RH1 — Digital I/O port H bit 1 |
| Broche 62 | RH2 — Digital I/O port H bit 2 |
| Broche 63 | RH3 — Digital I/O port H bit 3 |
| Broche 64 | RH4 — Digital I/O port H bit 4 |
| Broche 65 | RH5 — Digital I/O port H bit 5 |
| Broche 66 | RH6 — Digital I/O port H bit 6 |
| Broche 67 | RH7 — Digital I/O port H bit 7 |
| Broche 68 | RJ0 — Digital I/O port J bit 0 |
| Broche 69 | RJ1 — Digital I/O port J bit 1 |
| Broche 70 | RJ2 — Digital I/O port J bit 2 |
| Broche 71 | RJ3 — Digital I/O port J bit 3 |
| Broche 72 | RJ4 — Digital I/O port J bit 4 |
| Broche 73 | RJ5 — Digital I/O port J bit 5 |
| Broche 74 | RJ6 — Digital I/O port J bit 6 |
| Broche 75 | RJ7 — Digital I/O port J bit 7 |
| Broche 76 | D- — USB Full-Speed data minus (USB 2.0) |
| Broche 77 | D+ — USB Full-Speed data plus (USB 2.0) |
| Broche 78 | VUSB — Internal USB 3.3V regulator output (bypass cap required) |
| Broche 79 | AVSS — Analog ground reference |
| Broche 80 | AVDD — Analog positive supply (2.0V to 3.6V) |
Applications typiques
PIC18F86J55T-I/PT convient pour 7 applications: USB HID Peripherals, USB CDC Serial Bridges, Capacitive Touch User Interfaces, Industrial Data Loggers, Automotive LIN/J2602 Nodes, Low-Power Sensor Hubs with USB Charging, Home Automation Gateways.
USB HID Peripherals
The PIC18F86J55T-I/PT's on-chip USB 2.0 Full-Speed transceiver and 4KB dedicated USB buffer RAM make it a strong fit for USB HID peripherals such as keyboards, mice, game controllers, custom HID devices, and industrial pendants. The integrated 3.3V regulator and D+ pull-up eliminate the need for an external PHY, allowing direct bus-powered USB operation from a 5V VBUS rail. Designers can use the free Microchip USB stack to enumerate as a HID device, with 96KB Flash accommodating descriptor tables plus application logic. Compared to a USB-capable part without dedicated RAM, the 4KB buffer here prevents endpoint starvation and supports higher polling rates for low-latency HID reporting.
Recommandé
USB CDC Serial Bridges
For USB-to-UART virtual COM port adapters, the PIC18F86J55T-I/PT's two EUSART ports (LIN-capable) pair naturally with the USB CDC class to provide dual serial-over-USB channels from a single chip. The 48MHz core (12 MIPS) easily handles USB bulk transfer, hardware flow control, and bridge logic without CPU loading. The wide 2.0V to 3.6V supply range simplifies integration with both 3.3V-only UART targets and 5V-tolerant buses. Compared to discrete bridges, this integrated approach allows custom VID/PID, manufacturer string descriptors, and on-the-fly firmware updates via the Flash self-programming feature.
Recommandé
Capacitive Touch User Interfaces
The PIC18F86J55T-I/PT integrates Microchip's Charge Time Measurement Unit (CTMU), which combined with the on-chip ADC and 66 GPIO pins supports robust capacitive touch sensing for sliders, wheels, buttons, and proximity sensors. The CTMU measures capacitance with sub-pF resolution using a constant current source and timing circuit, enabling reliable touch detection even through 3mm of plastic overlay. The 96KB Flash is sufficient for advanced touch libraries such as Microchip's mTouch, and the nanoWatt sleep modes keep standby current low in battery-powered remote controls. Compared to discrete touch controllers, this integrated approach saves board space and BOM cost.
Recommandé
Industrial Data Loggers
Industrial data loggers benefit from the PIC18F86J55T-I/PT's 10-bit ADC with up to 16 input channels, 96KB Flash for FAT file system libraries and ring buffers, and 3.8KB RAM for sample windows. The MSSP port supports SPI Flash or SD card storage at up to 10 Mbit/s, while the two EUSARTs allow simultaneous RS-485 Modbus slave operation and USB host download. The industrial -40C to +85C operating range and 2.0V to 3.6V supply accommodate 24V-bus powered designs with buck regulators. Compared to MCU+external USB-IF solutions, the integrated USB makes field data extraction via laptop trivial.
Recommandé
Automotive LIN/J2602 Nodes
The PIC18F86J55T-I/PT's two LIN-capable EUSARTs make it a drop-in choice for automotive body electronics where Local Interconnect Network (LIN) bus nodes are needed for door modules, seat controllers, and mirror adjusters. The 48MHz core runs the LIN 2.1 stack with cycle-budget margin, and the 96KB Flash accommodates the LIN API plus application code. Industrial-grade temperature (-40C to +85C) and automotive-qualified PIC18F variants share this pinout for tier-1 designs. Compared to dedicated LIN slaves, the dual EUSART allows a single MCU to act as both a LIN master gateway and a peripheral node.
Recommandé
Low-Power Sensor Hubs with USB Charging
Battery-powered sensor hubs that occasionally connect to a phone or charger benefit from the PIC18F86J55T-I/PT's nanoWatt technology suite, including Idle, Sleep, and deep-sleep modes that drop current to the microampere range. The 66 GPIO pins accept multiple sensor inputs via I2C or SPI, while the USB port enables both data sync and battery charging from a single connector. The RTCC with dedicated 32 kHz oscillator keeps wall-clock time during sleep for timestamping. Compared to BLE-only solutions, USB provides higher bandwidth and avoids the radio certification burden for short-range tethered products.
Recommandé
Home Automation Gateways
The PIC18F86J55T-I/PT serves as a compact home automation gateway node that bridges USB-host controllers to sub-GHz radios, Zigbee dongles, or sensor chains. With 96KB Flash, the device can host both a USB HID/CDC stack and an SPI-based radio driver, acting as a translator between a touchscreen panel and a wireless mesh. The two EUSARTs enable simultaneous RS-485 wall-switch networks and USB diagnostic channels. Compared to single-radio gateways, this dual-bus configuration simplifies field debugging by exposing Modbus traffic over a USB CDC virtual COM port in parallel.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC18F86J55T-I/PT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC18F86J55-I/PT | PIC18F86J50T-I/PT | PIC18F86J15T-I/PT | PIC18F86J10T-I/PT | PIC18F85J94-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-TQFP (PT) 12x12 mm | 80-TQFP (PT) - same | 80-TQFP (PT) - same | 80-TQFP (PT) - same | 80-TQFP (PT) - same | 80-TQFP (PT) - same |
| Flash Memory | 96 KB | 96 KB | 96 KB | 96 KB | 96 KB | 32 KB |
| Data RAM | 3.8 KB + 4 KB USB buffer | 3.8 KB + 4 KB USB buffer | 3.8 KB (no dedicated USB buffer) | 3.8 KB (no USB block) | 3.8 KB | 2 KB |
| USB 2.0 Full-Speed | Yes (on-chip transceiver + 4 KB buffer) | Yes | Yes (no dedicated buffer) | No | No | No |
| Maximum Clock | 48 MHz (12 MIPS) | 48 MHz | 48 MHz | 48 MHz | 40 MHz | 64 MHz |
| I/O Pins | 66 | 66 | 66 | 66 | 66 | 66 |
| Operating Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Approx. Qty-1000 Price (USD) | $5.95 | ~$5.95 | ~$6.20 | ~$5.40 | ~$4.80 | ~$5.20 |
Principaux différenciateurs
- On-chip USB 2.0 Full-Speed transceiver with dedicated 4 KB buffer RAM (vs PIC18F86J50T-I/PT)
- USB-capable 80-TQFP PIC18J variant with full peripheral set (vs PIC18F86J15T-I/PT)
- 48MHz core with 66 I/O pins at 80-TQFP (vs PIC18F85J94-I/PT)
- Industrial-grade temperature range with nanoWatt low-power modes (vs PIC18F86J10T-I/PT)
Notes de conception
Estimated: at 48MHz CPU speed with all peripherals active, the PIC18F86J55T-I/PT draws roughly 25mA from a 3.3V supply, giving core power dissipation of approximately 82 mW. Decouple each VDD/VSS pair with a 100 nF X7R ceramic placed within 3mm of the pin; add a single 4.7uF bulk cap on the AVdd rail to support the ADC and USB 3.3V regulator transients. The on-chip VUSB regulator requires a 0.01uF bypass on the VUSB pin to meet USB Full-Speed signaling eye masks.
Keep the USB D+ and D- traces length-matched to within 2 mm and surrounded by a continuous ground pour on both sides of the PCB; route them on the top layer directly over an unbroken ground plane to maintain 90 ohm differential impedance (per USB 2.0 Full-Speed specification). Place the 48 MHz primary crystal within 6 mm of OSC1/OSC2 with short traces and a ground guard ring. Per the Microchip PIC18F86J55 hardware checklist, do not route high-frequency signals under the crystal traces.
Two common pitfalls when bringing up the PIC18F86J55T-I/PT: (1) forgetting to enable the internal USB pull-up on D+ in firmware - the device will not enumerate without it; (2) configuring the PLL without the correct CPUDIV divisor, which can lock up the core. Per Microchip AN679, always start with a conservative HS or INTIO clock and verify with the MPLAB Snap debugger before changing the PLL multiplier. Also note that USB Full-Speed operation requires Vdd at or above 3.0V.
For designs using the 10-bit ADC, route analog inputs (RA0-RA5, RB0-RB3) away from digital switching traces and place a small RC filter (typically 1k + 100pF) on each analog input to prevent crosstalk from adjacent digital lines. The AVdd supply should be driven from Vdd through a ferrite bead, and AVss must connect directly to the digital ground at a single point near the MCU. Per the Microchip PIC18F86J55 errata, the ADC may exhibit offset errors if the CTMU and ADC are active simultaneously without proper sequencing.
Informations de conformité
RoHS compliant per Microchip product page; halogen-free status not explicitly stated in retrieved data. Not AEC-Q100 qualified - this is an industrial-grade part; AEC-Q100 qualified PIC18F variants exist in the same family for automotive.
