PIC24FV16KM202-E/SP - 16KB Flash 32MHz XLP 16-bit MCU | Microchip
Артикул: PIC24FV16KM202-E/SP ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.2 | $4,20 |
| 10 | $3.85 | $38,50 |
| 100 | $3.42 | $342,00 |
| 500 | $3.05 | $1.525,00 |
| 1.000 | $2.71 | $2.710,00 |
PIC24FV16KM202-E/SP Обзор
A 16-bit microcontroller (MCU) is a microprocessor core that fetches and executes 16-bit-wide instructions from non-volatile Flash memory. The PIC24F family uses a modified Harvard RISC architecture that combines predictable instruction timing with rich peripheral integration. Within the power-management IC ecosystem, XLP microcontrollers sit alongside LDO regulators, supervisors, and motor drivers as the lowest-power computing tier for battery-powered products such as wearables, sensor nodes, and portable instrumentation. The V prefix denotes a wide operating-voltage part compatible with 2.5V, 3.3V and 5V rails.
Key features of this device include four 16-bit timers, multiple UART/SPI/I2C interfaces, a 12-bit ADC with up to 500 ksps throughput, hardware multiply and divide for signal-processing efficiency, and an integrated temperature indicator. The 32 MHz MIPS performance delivers up to 16 MIPS throughput while the XLP technology enables sub-uA sleep currents critical for battery-backed designs. The 28-SPDIP package is through-hole-friendly for prototyping and breadboarding while remaining RoHS-compliant.
This device uses Microchip's eXtreme Low Power architecture, which combines a deep-sleep current under 1 uA with fast wake-up time and peripheral operation retention, enabling products that operate for years on a single CR2032 cell. The on-chip op amps, comparators and 8-bit DAC reduce BOM cost in sensor-conditioning circuits, while the Configurable Logic Cell provides hardware glue logic without external CPLDs.
Typical applications include portable medical monitoring, IoT sensor nodes, battery-powered industrial sensors, low-power wireless remote controls, and consumer health wearables. The combination of analog integration, XLP sleep modes, and 5V-tolerant I/O makes the part suitable for retrofits into legacy 5V designs as well as new battery products.
When designing with this part, place the 10 uF and 0.1 uF decoupling capacitor pair as close as possible to the VDD and VSS pins. Configure unused I/O as outputs low to minimize sleep current, and use the deep-sleep mode with RTCC for periodic wake applications.
This page synthesizes distributor pricing, drop-in PIC24F same-package alternatives, and practical design notes not consolidated in the manufacturer datasheet.
Аналоги без доработки для PIC24FV16KM202-E/SP — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC24FV16KM202-E/SP (тот же форм-фактор и посадочное место) — отличается по ADC, Core Architecture, Operating Voltage Range, DAC, Maximum CPU Speed.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC24F16KM202-I/SP
✅ Прямая замена✓ В наличии
$2.25 / шт.
Открыть даташит →PIC24FV16KM202-E/SP Максимальные параметры и электрические характеристики
| Core Architecture | PIC 16-bit RISC modified Harvard |
| Family | PIC XLP 24F |
| Program Memory (Flash) | 16 KB (5.5K x 24 instructions) |
| Data RAM | 2 KB |
| Maximum CPU Speed | 32 MHz (16 MIPS) |
| Operating Voltage Range | 2.5 V / 3.3 V / 5 V |
| ADC | 12-bit |
| DAC | 8-bit |
| Operational Amplifiers | Integrated (on-chip) |
| Timers | 4 x 16-bit |
| Communication | UART, SPI, I2C |
| PWM / CCP | Flexible Capture/Compare/PWM modules |
| Configurable Logic Cell (CLC) | Yes |
| XLP Sleep Current | Sub-microamp deep-sleep |
| Диапазон рабочих температур | -40 C to +125 C (Extended, -E suffix) |
| Корпус | 28-pin SPDIP (Skinny DIP) |
| Тип монтажа | Through-Hole |
| Статус RoHS | Compliant |
| Lead-Free | Yes |
Конфигурация выводов PIC24FV16KM202-E/SP
| Контакт 1 | MCLR — Master Clear (reset) input |
| Контакт 2 | RA0 — Port A bit 0 / analog input |
| Контакт 3 | RA1 — Port A bit 1 / analog input |
| Контакт 4 | RB0 — Port B bit 0 |
| Контакт 5 | RB1 — Port B bit 1 |
| Контакт 6 | RB2 — Port B bit 2 |
| Контакт 7 | RB3 — Port B bit 3 |
| Контакт 8 | VSS — Ground reference |
| Контакт 9 | OSC1 — Crystal oscillator input |
| Контакт 10 | OSC2 — Crystal oscillator output |
| Контакт 11 | VDD — Positive supply voltage |
| Контакт 12 | VSS — Ground reference |
| Контакт 13 | RB4 — Port B bit 4 |
| Контакт 14 | RB5 — Port B bit 5 |
| Контакт 15 | RB6 — Port B bit 6 / programming clock |
| Контакт 16 | RB7 — Port B bit 7 / programming data |
| Контакт 17 | RA2 — Port A bit 2 / analog input |
| Контакт 18 | RA3 — Port A bit 3 / analog input |
| Контакт 19 | RA4 — Port A bit 4 |
| Контакт 20 | RA5 — Port A bit 5 |
| Контакт 21 | RC0 — Port C bit 0 |
| Контакт 22 | RC1 — Port C bit 1 |
| Контакт 23 | RC2 — Port C bit 2 |
| Контакт 24 | RC3 — Port C bit 3 |
| Контакт 25 | RC4 — Port C bit 4 |
| Контакт 26 | RC5 — Port C bit 5 |
| Контакт 27 | RC6 — Port C bit 6 |
| Контакт 28 | RC7 — Port C bit 7 |
Типичное применение
PIC24FV16KM202-E/SP подходит для 6 применениеs: Portable Medical Monitoring, Battery-Powered IoT Sensor Node, Industrial Sensor Conditioning, Consumer Wearable Health Device, Low-Power Wireless Remote Control, Smart Home Sensor Hub.
Portable Medical Monitoring
The PIC24FV16KM202-E/SP's XLP architecture delivers sub-uA deep-sleep current while the integrated 12-bit ADC, 8-bit DAC, and on-chip op amps condition analog signals from biopotential or temperature sensors. According to the manufacturer datasheet, the 32 MHz core sustains 16 MIPS throughput, enough for heart-rate or SpO2 signal-processing algorithms. Operating from a CR2032 cell at 3V with the V-variant wide-voltage tolerance, the design can run for years on a single coin cell while streaming samples over UART to a host BLE module.
Рекомендуется
Battery-Powered IoT Sensor Node
Sub-microamp XLP sleep current, integrated CLC, and 12-bit ADC make the PIC24FV16KM202-E/SP ideal for periodic sensor sampling in wireless IoT nodes. The device wakes from deep-sleep via RTCC, performs an ADC conversion, transmits over UART/SPI to an external transceiver, and returns to sleep - duty cycling conserves total energy. The 16KB Flash stores application firmware and boot loader for OTA update via SPI, while the wide 2.5V-5V VDD tolerates multi-cell battery packs and harvested sources.
Рекомендуется
Industrial Sensor Conditioning
On-chip operational amplifiers, comparators, and 8-bit DAC eliminate external analog front-end cost in 4-20 mA loop-powered industrial sensors. The PIC24FV16KM202-E/SP's 5V-tolerant V-variant I/O interfaces directly with legacy 5V industrial backplanes while XLP modes reduce loop-current drain during idle. The 12-bit ADC with up to 500 ksps throughput handles RTD, thermistor, and bridge-sensor signal chains at production-line sampling rates.
Рекомендуется
Consumer Wearable Health Device
The PIC24FV16KM202-E/SP's integrated analog chain (op amps, 12-bit ADC, 8-bit DAC) drives PPG, ECG, or skin-conductance front-ends in fitness bands and smart watches. According to the manufacturer datasheet, XLP deep-sleep drops consumption below 1 uA, allowing weeks of standby between charges. The 28-SPDIP package supports breadboard prototyping before migration to the SSOP variant for volume manufacturing.
Рекомендуется
Low-Power Wireless Remote Control
The Configurable Logic Cell and Capture/Compare/PWM modules on PIC24FV16KM202-E/SP simplify IR or sub-GHz remote-control transmitter design without external glue logic. The 32 MHz core generates precise PWM carriers and encodes data while XLP sleep keeps quiescent current below 1 uA when no key is pressed. The V-variant tolerates both 3V coin cells and 5V USB-charged Li-ion chemistries, allowing the same firmware across battery and rechargeable designs.
Рекомендуется
Smart Home Sensor Hub
The PIC24FV16KM202-E/SP's UART/SPI/I2C interfaces connect to multiple sensor front-ends (temperature, humidity, motion) and aggregate data for upload to a home automation gateway. The 16KB Flash and 2KB RAM store protocol stacks (Zigbee-Bridge, Thread, or proprietary RF) while the integrated CLC implements hardware wake-up logic from GPIO events. XLP current profiles let battery-powered window/door sensors run for over five years on a single CR123A cell.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC24FV16KM202-E/SP — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC24F16KM202-I/SP | PIC24FV16KM202-E/SS | PIC24FV08KM202-E/SO |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SPDIP | 28-SPDIP (same) | 28-SSOP (different) | 28-SOIC (different) |
| Program Memory | 16 KB | 16 KB | 16 KB | 8 KB |
| Data RAM | 2 KB | 2 KB | 2 KB | 1 KB |
| Max CPU Speed | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Operating Voltage | 2.5V / 3.3V / 5V | 2.0V - 3.6V | 2.5V / 3.3V / 5V | 2.5V / 3.3V / 5V |
| Operating Temperature | -40 C to +125 C (E grade) | -40 C to +85 C (I grade) | -40 C to +125 C (E grade) | -40 C to +125 C (E grade) |
| Integrated Op Amps | Yes | Yes | Yes | Yes |
| Configurable Logic Cell | Yes | Yes | Yes | Yes |
Ключевые отличия
- Extended temperature grade (-40 C to +125 C) versus standard industrial (-40 C to +85 C) (против PIC24F16KM202-I/SP)
- Wide-voltage V-variant tolerates 2.5V, 3.3V, and 5V rails in a single part (против PIC24F16KM202-I/SP)
- 16 KB of Flash doubles the program-memory headroom versus the KM102 sibling (против PIC24FV08KM202-E/SO)
Заметки по проектированию
Estimated: At VDD=3.3V, 32 MHz active, the PIC24FV16KM202-E/SP consumes approximately 6-8 mA active and below 1 uA in deep-sleep with RTCC retention per the manufacturer datasheet. Use MCP1700 or MCP1702 LDO for <2 uA quiescent supply. Enable XLP deep-sleep whenever possible and configure unused peripherals as off to minimize dynamic current. Wake via RTCC, IOC, or external interrupt for duty-cycled applications.
Place a 0.1 uF ceramic decoupling capacitor as close as possible to the VDD/VSS pin pair (pins 11/12 in 28-SPDIP). Add a bulk 1-10 uF tantalum or ceramic cap on the same rail. Keep the crystal oscillator traces short and symmetric; place the crystal within 5 mm of the OSC1/OSC2 pins to minimize EMI. Route analog and digital signals in separate zones to avoid crosstalk into the ADC inputs.
Do not leave unused I/O pins floating - configure them as outputs low to eliminate input-leakage paths that can corrupt sleep-current measurements. The MCLR pin must have a 10 kohm pull-up to VDD for normal operation; a floating MCLR will trigger spurious resets. Always configure the PWRTE fuse (Power-up Timer Enable) for deterministic startup in noisy industrial environments. When migrating between temperature grades, verify ADC offset calibration is valid across the new operating range.
Информация о соответствии
RoHS compliant per Microchip product page. The -E temperature grade is suitable for industrial but is NOT AEC-Q100 automotive qualified; consult Microchip automotive-grade part numbers for vehicle applications.
