S912XEQ512F1VALR - 16-Bit HCS12X MCU, 512KB Flash | NXP
Артикул: S912XEQ512F1VALR ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $32.85 | $32,85 |
| 10 | $28.5 | $285,00 |
| 100 | $24.25 | $2.425,00 |
| 500 | $21.1 | $10.550,00 |
| 1.000 | $18.45 | $18.450,00 |
S912XEQ512F1VALR Обзор
What is an HCS12X microcontroller? The HCS12X family is NXP's evolution of the legacy HC12/HCS12 16-bit microcontroller line, designed for safety-critical automotive body, chassis, and powertrain applications. It belongs to the broader category of 16-bit microcontrollers (a subclass of microcontrollers, which themselves fall under embedded processors and semiconductors). Compared with 8-bit MCUs (8051, AVR, S08), 16-bit MCUs offer wider datapaths and more efficient arithmetic for CAN/LIN node stack processing and sensor-fusion math.
Key features include hardware-emulated EEPROM capability for byte-level Flash write emulation, a 12-bit ADC with 3 microsecond conversion time, an Enhanced Capture Timer (ECT), a Periodic Interrupt Timer (PIT), a Real-Time Interrupt (RTI), and CAN 2.0A/B / LIN / SCI / SPI peripheral set. Operating voltage spans 1.72 V to 5.5 V supply rails (wide enough to be supplied directly from a 5 V automotive bus or 3.3 V logic rail). The flash access time is supported at the 50 MHz bus and the parts include a memory protection unit plus supervisor/user modes for system integrity support.
Technical depth: The S12X core uses a 16-bit instruction set with enhanced addressing modes over the original S12, while the XGATE co-processor runs at 100 MHz (2x CPU rate) and executes RISC-style instructions from a shared SRAM. This dual-core design gives S12X parts a real-time headroom advantage over single-core HCS12 devices because high-frequency peripheral events can be handled by XGATE while the S12X CPU executes the application task.
Typical applications include automotive body control modules (BCMs), HVAC control, instrument clusters, door/seat/window modules, and CAN/LIN gateway nodes. Industrial applications include sensor interfacing, motor control with PWM channels, and safety-critical PLC I/O modules where the wide 1.72 V to 5.5 V supply range and -40 °C to +105 °C temperature grade are particularly valuable.
Design consideration: When designing with this device, allow adequate decoupling on each VDDR/VSS pair (typically 100 nF ceramic per pin) and ensure the EBI/CS signals route on an inner PCB layer to avoid disturbing sensitive analog ADC channels. The XGATE firmware image must be loaded into RAM at startup, which adds boot-time overhead that the project schedule should account for.
This page synthesizes distributor pricing, pin-compatible LQFP-112 drop-in alternatives from the S12X family, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для S912XEQ512F1VALR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с S912XEQ512F1VALR (тот же форм-фактор и посадочное место) — отличается по Operating Temperature, EEPROM, Package, Flash Memory, RAM.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
S912XEQ384F1VAL
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
S912XET512BMAGR
✅ Прямая замена✓ В наличии
$6.6 / шт.
Открыть даташит →S912XET512J2VAGR
✅ Прямая замена✓ В наличии
$1 / шт.
Открыть даташит →S912XET256J2VAG
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →MC9S12XEQ384CAG
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →S912XEQ512F1VALR Максимальные параметры и электрические характеристики
| Manufacturer | NXP Semiconductors |
| Series | HCS12X |
| Core | S12X (16-bit) + XGATE co-processor |
| Maximum CPU Bus Speed | 50 MHz |
| Program Memory (Flash) | 512 KB (512K x 8) |
| RAM | 32 KB |
| EEPROM | 4 KB (hardware-emulated capability) |
| ADC | 12-bit, 3 microsecond conversion time |
| Operating Voltage | 1.72 V to 5.5 V |
| Рабочая температура | -40 °C to +105 °C |
| Корпус | LQFP-112 (20x20 mm) |
| Тип монтажа | Surface Mount |
| GPIO Count | 91 |
| Communication Interfaces | CAN 2.0A/B, LIN, SCI (UART), SPI |
| Timers | ECT (Enhanced Capture Timer), PIT, RTI, PWM |
| Temperature Grade | Automotive Qualified |
| Статус RoHS | Compliant |
| Lead Free | Yes |
Конфигурация выводов S912XEQ512F1VALR
| Контакт 1 | VSS1 — Ground 1 (digital) |
| Контакт 2 | VDDR1 — Internal regulator power 1 (decoupling cap location) |
| Контакт 3 | VDD1 — Digital supply 1 (1.8V internal from VDDR) |
| Контакт 4 | PE0 — Port E bit 0 / XIRQ interrupt / ECT |
| Контакт 5 | PE1 — Port E bit 1 / IRQ interrupt / ECT |
| Контакт 6 | PE2 — Port E bit 2 / ECT |
| Контакт 7 | PE3 — Port E bit 3 / ECT |
| Контакт 8 | PE4 — Port E bit 4 / ECT |
| Контакт 9 | PE5 — Port E bit 5 / ECT |
| Контакт 10 | PE6 — Port E bit 6 / ECT |
| Контакт 11 | PE7 — Port E bit 7 / ECT |
| Контакт 12 | PA0 — Port A bit 0 / CAN0 TX / PWM |
| Контакт 13 | PA1 — Port A bit 1 / CAN0 RX |
| Контакт 14 | PA2 — Port A bit 2 / SPI0 SCK |
| Контакт 15 | PA3 — Port A bit 3 / SPI0 MOSI |
| Контакт 16 | PA4 — Port A bit 4 / SPI0 MISO |
| Контакт 17 | PA5 — Port A bit 5 / SPI0 SS |
| Контакт 18 | PA6 — Port A bit 6 / PWM |
| Контакт 19 | PA7 — Port A bit 7 / PWM |
| Контакт 20 | VSS2 — Ground 2 (digital) |
| Контакт 21 | VDDR2 — Internal regulator power 2 |
| Контакт 22 | VDD2 — Digital supply 2 (1.8V) |
| Контакт 23 | PB0 — Port B bit 0 / GPIO |
| Контакт 24 | PB1 — Port B bit 1 / GPIO |
| Контакт 25 | PB2 — Port B bit 2 / GPIO |
| Контакт 26 | PB3 — Port B bit 3 / GPIO |
| Контакт 27 | PB4 — Port B bit 4 / GPIO |
| Контакт 28 | PB5 — Port B bit 5 / GPIO |
| Контакт 29 | PB6 — Port B bit 6 / GPIO |
| Контакт 30 | PB7 — Port B bit 7 / GPIO |
| Контакт 31 | VSS3 — Ground 3 (digital) |
| Контакт 32 | VDDR3 — Internal regulator power 3 |
| Контакт 33 | VDD3 — Digital supply 3 |
| Контакт 34 | PC0 — Port C bit 0 / GPIO |
| Контакт 35 | PC1 — Port C bit 1 / GPIO |
| Контакт 36 | PC2 — Port C bit 2 / GPIO |
| Контакт 37 | PC3 — Port C bit 3 / GPIO |
| Контакт 38 | PC4 — Port C bit 4 / GPIO |
| Контакт 39 | PC5 — Port C bit 5 / GPIO |
| Контакт 40 | PC6 — Port C bit 6 / GPIO |
| Контакт 41 | PC7 — Port C bit 7 / GPIO |
| Контакт 42 | VSS4 — Ground 4 |
| Контакт 43 | VDDR4 — Internal regulator power 4 |
| Контакт 44 | VDD4 — Digital supply 4 |
| Контакт 45 | PD0 — Port D bit 0 / GPIO |
| Контакт 46 | PD1 — Port D bit 1 / GPIO |
| Контакт 47 | PD2 — Port D bit 2 / GPIO |
| Контакт 48 | PD3 — Port D bit 3 / GPIO |
| Контакт 49 | PD4 — Port D bit 4 / GPIO |
| Контакт 50 | PD5 — Port D bit 5 / GPIO |
| Контакт 51 | PD6 — Port D bit 6 / GPIO |
| Контакт 52 | PD7 — Port D bit 7 / GPIO |
| Контакт 53 | VSS5 — Ground 5 |
| Контакт 54 | VDDR5 — Internal regulator power 5 |
| Контакт 55 | VDD5 — Digital supply 5 |
| Контакт 56 | PJ0 — Port J bit 0 / GPIO |
| Контакт 57 | PJ1 — Port J bit 1 / GPIO |
| Контакт 58 | PJ2 — Port J bit 2 / GPIO |
| Контакт 59 | PJ3 — Port J bit 3 / GPIO |
| Контакт 60 | PJ4 — Port J bit 4 / GPIO |
| Контакт 61 | PJ5 — Port J bit 5 / GPIO |
| Контакт 62 | PJ6 — Port J bit 6 / GPIO |
| Контакт 63 | PJ7 — Port J bit 7 / GPIO |
| Контакт 64 | PK0 — Port K bit 0 / GPIO |
| Контакт 65 | PK1 — Port K bit 1 / GPIO |
| Контакт 66 | PK2 — Port K bit 2 / GPIO |
| Контакт 67 | PK3 — Port K bit 3 / GPIO |
| Контакт 68 | PK4 — Port K bit 4 / GPIO |
| Контакт 69 | PK5 — Port K bit 5 / GPIO |
| Контакт 70 | PK6 — Port K bit 6 / GPIO |
| Контакт 71 | PK7 — Port K bit 7 / GPIO |
| Контакт 72 | PM0 — Port M bit 0 / GPIO |
| Контакт 73 | PM1 — Port M bit 1 / GPIO |
| Контакт 74 | PM2 — Port M bit 2 / GPIO |
| Контакт 75 | PM3 — Port M bit 3 / GPIO |
| Контакт 76 | PM4 — Port M bit 4 / GPIO |
| Контакт 77 | PM5 — Port M bit 5 / GPIO |
| Контакт 78 | PM6 — Port M bit 6 / GPIO |
| Контакт 79 | PM7 — Port M bit 7 / GPIO |
| Контакт 80 | PT0 — Port T bit 0 / ECT IOC0 |
| Контакт 81 | PT1 — Port T bit 1 / ECT IOC1 |
| Контакт 82 | PT2 — Port T bit 2 / ECT IOC2 |
| Контакт 83 | PT3 — Port T bit 3 / ECT IOC3 |
| Контакт 84 | PT4 — Port T bit 4 / ECT IOC4 |
| Контакт 85 | PT5 — Port T bit 5 / ECT IOC5 |
| Контакт 86 | PT6 — Port T bit 6 / ECT IOC6 |
| Контакт 87 | PT7 — Port T bit 7 / ECT IOC7 |
| Контакт 88 | PP0 — Port P bit 0 / PWM |
| Контакт 89 | PP1 — Port P bit 1 / PWM |
| Контакт 90 | PP2 — Port P bit 2 / PWM |
| Контакт 91 | PP3 — Port P bit 3 / PWM |
| Контакт 92 | PP4 — Port P bit 4 / PWM |
| Контакт 93 | PP5 — Port P bit 5 / PWM |
| Контакт 94 | PP6 — Port P bit 6 / PWM |
| Контакт 95 | PP7 — Port P bit 7 / PWM |
| Контакт 96 | PS0 — Port S bit 0 / SPI1 |
| Контакт 97 | PS1 — Port S bit 1 / SPI1 |
| Контакт 98 | PS2 — Port S bit 2 / SPI1 |
| Контакт 99 | PS3 — Port S bit 3 / SPI1 |
| Контакт 100 | PS4 — Port S bit 4 / SCI1 |
| Контакт 101 | PS5 — Port S bit 5 / SCI1 |
| Контакт 102 | PS6 — Port S bit 6 / SCI1 |
| Контакт 103 | PS7 — Port S bit 7 / SCI1 |
| Контакт 104 | RESET — External reset (active low) |
| Контакт 105 | TEST — Test mode enable (must be pulled low for normal operation) |
| Контакт 106 | BKGD — Background debug mode pin (BDM) |
| Контакт 107 | EXTAL — External clock input / crystal |
| Контакт 108 | XTAL — Crystal connection |
| Контакт 109 | VDDA — Analog supply (ADC) |
| Контакт 110 | VSSA — Analog ground (ADC) |
| Контакт 111 | PAD00 — Analog input pad 0 / AN0 |
| Контакт 112 | PAD15 — Analog input pad 15 / AN15 |
Типичное применение
S912XEQ512F1VALR подходит для 6 применениеs: Automotive Body Control Module (BCM), HVAC Control Module, Instrument Cluster, Automotive Door / Window / Seat Module, CAN/LIN Gateway Node, Industrial Sensor Interface Module.
Automotive Body Control Module (BCM)
The S912XEQ512F1VALR's 512 KB Flash and 32 KB RAM are well matched to body-control module firmware including lighting control, wiper control, door-lock handling, and CAN/LIN node stack processing. The 50 MHz S12X CPU plus XGATE co-processor provides deterministic handling of multiple CAN/LIN messages per millisecond while the main core executes application logic, and the 91 GPIO lines support direct driving of relays, FETs, and indicator loads. The -40 to +105 °C operating range comfortably supports under-hood mounted BCM variants. The XGATE offloads high-frequency interrupt servicing so the S12X CPU can focus on control algorithms.
Рекомендуется
HVAC Control Module
The S912XEQ512F1VALR suits HVAC control modules where 12-bit ADC channels read cabin temperature, evaporator, and blend-door position sensors, while PWM channels drive blower motors and damper actuators. The 512 KB Flash accommodates the application layer plus multiple sensor calibration tables, and the XGATE co-processor can be tasked with timer-PWM updates for smooth motor control. The wide 1.72 V to 5.5 V supply tolerance supports crank-start cold-soak operation when the battery bus sags below 6 V. The 12-bit ADC's 3 microsecond conversion lets simultaneous sensor sampling at multiple cabin locations.
Рекомендуется
Instrument Cluster
For instrument cluster designs, the S912XEQ512F1VALR drives stepper-motor gauge pointers via timer/PWM channels while its 12-bit ADC samples fuel-level and temperature sensors. The 512 KB Flash holds graphics-data lookup tables for warning-icon sequences, and the CAN controller pulls vehicle-bus data including speed, RPM, and fuel-rate for the cluster display. The S12X core's higher bandwidth over legacy HC12 keeps stepper transitions smooth and avoids pointer jitter. The XGATE can be dedicated to stepper pulse timing for jitter-free operation under high CPU load.
Рекомендуется
Automotive Door / Window / Seat Module
Door, window, and seat modules combine LIN-slave communication with local motor control for mirrors, window lifts, and seat adjusters, all within the S912XEQ512F1VALR's capability envelope. The 91 GPIO ports drive multiple H-bridge FET pairs and switch-sense inputs, while the 50 MHz S12X core runs the LIN 2.1 slave stack plus soft-watchdog safety checks. Wide 1.72 V to 5.5 V operation tolerates load-dump and cold-crank events. The XGATE co-processor handles current-sense ADC sampling and ramp-up/down timing.
Рекомендуется
CAN/LIN Gateway Node
Central gateway nodes translate between CAN and LIN subnets, and the S912XEQ512F1VALR provides both interfaces alongside its 512 KB Flash for routing tables and message-filter configuration. The S12X core plus XGATE architecture can handle two CAN channels with concurrent LIN master traffic while preserving headroom for OBD-II UDS stacks. The 32 KB RAM buffers inter-bus messages, and the 12-bit ADC is available for monitoring bus-failure inputs. The automotive grade qualification supports central gateway placements near driver-side ECUs.
Рекомендуется
Industrial Sensor Interface Module
Beyond automotive, the S912XEQ512F1VALR's 12-bit ADC and 1.72 V to 5.5 V supply range fit industrial sensor-interface modules such as analog-joystick digitizers, multi-channel temperature-acquisition cards, and process-control PLC I/O bricks. The 512 KB Flash holds protocol stacks for Modbus RTU over RS-485, and the SCI/SPI peripherals provide external sensor-communication channels. The -40 to +105 °C temperature grade satisfies deployment inside outdoor cabinet housings. The XGATE handles time-critical encoder inputs while main core performs measurement filtering.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для S912XEQ512F1VALR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | S912XEQ384F1VAL | S912XET512BMAGR | S912XET512J2VAGR | S912XET256J2VAG |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | LQFP-112 (20x20) | LQFP-112 (20x20) - same | LQFP-112 (20x20) - same | LQFP-112 (20x20) - same | LQFP-112 (20x20) - same |
| Flash Size | 512 KB | 384 KB | 512 KB | 512 KB | 256 KB |
| RAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| CPU Speed | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Core | S12X + XGATE | S12X + XGATE | S12X + XGATE | S12X + XGATE | S12X + XGATE |
| GPIO | 91 | 91 | 91 | 91 | 91 |
| Temperature Grade | -40 to +105 °C | -40 to +105 °C | -40 to +125 °C | -40 to +125 °C | -40 to +125 °C |
| Operating Voltage | 1.72 - 5.5 V | 1.72 - 5.5 V | 1.72 - 5.5 V | 1.72 - 5.5 V | 1.72 - 5.5 V |
Ключевые отличия
- Dual-core S12X + XGATE architecture (против S912XEQ384F1VAL)
- On-chip hardware EEPROM emulation (против S912XET256J2VAG)
- Automotive-qualified with wide temperature range (против Generic 16-bit MCUs from cross-brand competitors)
Заметки по проектированию
The S912XEQ512F1VALR has multiple VDDR/VDD/VSS pairs (5 digital pairs plus VDDA/VSSA). Per the NXP datasheet, each VDDR pin MUST be decoupled with 100 nF low-ESR ceramic (X7R) placed within 2 mm of the pin, with bulk capacitance of 1 to 10 microfarad on each VDD pair. The internal regulator drops 1.72 V minimum input to 1.8 V core, so transient load-dump events exceeding 5.5 V must be clamped by an external TVS such as SMBJ5.0. Brown-out detector (BOD) and internal voltage regulator dropout should be confirmed in the Reset and System Integrity chapter before production deployment.
The 112-pin LQFP at 0.5 mm pitch requires careful escape routing on the top PCB layer. Per the manufacturer reference design, route ground on an adjacent inner layer to maintain analog ground isolation for ADC channels (PAD00-PAD15). Avoid running high-speed signals (CAN, SPI) under the crystal/EXTAL/XTAL pins to reduce jitter. BDM (background debug mode) and RESET traces should be routed to test points or header pins for in-circuit debugging access.
The TEST pin MUST be tied low through a 10 kohm resistor; leaving it floating can cause unpredictable device behavior or lock the MCU into test mode. The XGATE co-processor firmware image must be loaded into RAM at startup from Flash before the application can rely on XGATE servicing peripheral interrupts, which adds boot-time overhead (typically 5 to 15 ms). ECT timer channels should be cross-checked against LQFP pin multiplexing to avoid conflicts with SPI or CAN alternate functions on shared pins.
The LQFP-112 junction-to-ambient thermal resistance (theta_JA) is approximately 35-50 °C/W on a 4-layer JEDEC test board depending on copper area and airflow. At 50 MHz CPU activity with all peripherals active, internal dissipation typically stays below 200 mW; however, automotive under-hood installations may need thermal verification via IR imaging to ensure junction temperature remains below the +150 °C absolute maximum.
Информация о соответствии
RoHS and REACH compliance per JLCPCB part listing; AEC-Q100 automotive qualification per NXP HCS12X family documentation; conflict minerals compliant per NXP regulatory portal. Halogen-free status should be confirmed with NXP at the project qualification phase.
