SN74AVC4T245QWRGYRQ1 - 4-Bit Dual-Supply Level Shifter AEC-Q100 | TI
Артикул: SN74AVC4T245QWRGYRQ1 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $0.62 | $0,62 |
| 10 | $0.56 | $5,60 |
| 100 | $0.45 | $45,00 |
| 500 | $0.38 | $190,00 |
| 1.000 | $0.31 | $310,00 |
SN74AVC4T245QWRGYRQ1 Обзор
A bus transceiver is a digital interface IC that combines transmit and receive paths in one device, allowing bidirectional data flow between two buses. The SN74AVC4T245-Q1 belongs to the voltage-level translator family, a subset of interface ICs within the broader integrated circuits category. Level translation is essential when connecting components with different I/O voltages, such as a 1.8 V microcontroller interfacing with a 3.3 V peripheral.
Key features include dual-supply operation with VCCA and VCCB each accepting 1.2 V to 3.6 V, tri-state outputs for bus isolation, and Ioff partial-power-down protection that disables outputs and prevents damaging backflow current when either supply is removed. A typical propagation delay of 2.1 ns and data rates up to 380 Mbps make the device suitable for SPI, I2C, UART, and parallel GPIO interfaces.
The CMOS architecture supports use as two independent 2-bit transceivers or one 4-bit transceiver. Direction control (1DIR, 2DIR) and output-enable (1OE, 2OE) pins are referenced to VCCA, simplifying control-logic design in mixed-voltage systems. The device operates asynchronously, requiring no clock signal, and is fully specified over the -40C to +125C automotive temperature range.
Typical applications include automotive body control modules, ADAS ECUs, infotainment systems, and industrial automation. In ECUs, it bridges 1.8 V or 2.5 V MCUs to 3.3 V sensors, CAN transceiver interfaces, SPI flash, and general-purpose GPIO level shifting. Site-available companions include the SN65HVD230QDRQ1 CAN transceiver and SN74LVC1T45QDCKRQ1 single-bit translator.
Design tip: decouple VCCA and VCCB with 0.1 uF capacitors placed close to the pins, and ensure DIR/OE signals (VCCA domain) are stable before data transmission to avoid bus contention.
Аналоги без доработки для SN74AVC4T245QWRGYRQ1 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с SN74AVC4T245QWRGYRQ1 (тот же форм-фактор и посадочное место) — отличается по Direction Control, Output Type.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
SN74AVC4T245RGYR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
SN74AVC4T245QWRGYRQ1 Максимальные параметры и электрические характеристики
| Функция | 4-bit dual-supply bus transceiver with configurable voltage translation |
| Supply Voltage VCCA | 1.2 V to 3.6 V |
| Supply Voltage VCCB | 1.2 V to 3.6 V |
| Number of Bits | 4 (configurable as two 2-bit transceivers) |
| Тип выхода | 3-State |
| Propagation Delay | 2.1 ns typical |
| Скорость передачи данных | Up to 380 Mbps |
| Direction Control | 1DIR, 2DIR (VCCA referenced) |
| Output Enable | 1OE, 2OE (VCCA referenced) |
| Ioff Partial-Power-Down | Yes |
| Рабочая температура | -40C to +125C (AEC-Q100 Grade 1) |
| Корпус | VQFN-16 (RGY) 4x3.5 mm |
| Тип монтажа | Surface Mount |
| Automotive Qualification | AEC-Q100 qualified |
| Статус RoHS | Compliant |
| Technology Family | AVC (Advanced Very-low-voltage CMOS) |
Конфигурация выводов SN74AVC4T245QWRGYRQ1
| Контакт 1 | 1OE — Output enable for 1A/1B ports (VCCA referenced, active low) |
| Контакт 2 | 1DIR — Direction control for 1A/1B ports (VCCA referenced) |
| Контакт 3 | VCCA — A-side power supply (1.2 V to 3.6 V) |
| Контакт 4 | GND — Ground |
| Контакт 5 | 1A1 — A-side data 1 |
| Контакт 6 | 1A2 — A-side data 2 |
| Контакт 7 | 2A1 — A-side data 3 |
| Контакт 8 | 2A2 — A-side data 4 |
| Контакт 9 | 2B2 — B-side data 4 |
| Контакт 10 | 2B1 — B-side data 3 |
| Контакт 11 | 1B2 — B-side data 2 |
| Контакт 12 | 1B1 — B-side data 1 |
| Контакт 13 | VCCB — B-side power supply (1.2 V to 3.6 V) |
| Контакт 14 | 2DIR — Direction control for 2A/2B ports (VCCA referenced) |
| Контакт 15 | 2OE — Output enable for 2A/2B ports (VCCA referenced, active low) |
| Контакт 16 | GND — Ground / thermal pad |
Типичное применение
SN74AVC4T245QWRGYRQ1 подходит для 6 применениеs: Automotive Body Control Modules, ADAS ECUs and Sensor Interfaces, Automotive Infotainment Systems, Industrial Automation and PLC I/O, Microcontroller GPIO Level Shifting, SPI Flash and Memory Interface Translation.
Automotive Body Control Modules
In body control modules (BCMs), the SN74AVC4T245QWRGYRQ1 bridges the low-voltage MCU domain (typically 1.8 V or 2.5 V) to 3.3 V peripheral buses controlling lighting, door, and seat functions. Its AEC-Q100 Grade 1 rating (-40C to +125C) survives under-hood-adjacent thermal environments, while the 2.1 ns propagation delay and 380 Mbps capability support fast GPIO and parallel status buses. The Ioff partial-power-down feature prevents backfeed during BCM sleep states, keeping quiescent drain low.
Рекомендуется
ADAS ECUs and Sensor Interfaces
ADAS electronic control units frequently mix 1.8 V processors with 3.3 V radar, camera, and CAN interfaces. The SN74AVC4T245QWRGYRQ1 translates these buses with 380 Mbps headroom, sufficient for SPI sensor control at 50 MHz and above. Configurable operation as two independent 2-bit transceivers lets designers split SPI (data/control) from general GPIO within one package. Tri-state outputs with VCCA-referenced OE enable safe bus isolation during sensor resets, and Ioff protection handles asymmetric power-up sequencing common in ADAS domains.
Рекомендуется
Automotive Infotainment Systems
Infotainment head units combine application processors running at 1.8 V I/O with 3.3 V audio codecs, tuners, and display interfaces. The SN74AVC4T245QWRGYRQ1 provides four bidirectional translation channels at up to 380 Mbps with only 2.1 ns typical delay, preserving timing margins on I2S control and fast parallel command buses. Dual-supply architecture (VCCA/VCCB from 1.2 V to 3.6 V) allows any-to-any voltage pairing, and the RGY VQFN-16 footprint of 4x3.5 mm conserves board space behind the display stack.
Рекомендуется
Industrial Automation and PLC I/O
In industrial PLCs and automation controllers, 3.3 V or 2.5 V microcontrollers must drive 3.3 V field-side logic and communication modules. The SN74AVC4T245QWRGYRQ1 handles this with its wide 1.2-3.6 V dual-supply range and robust tri-state outputs for shared backplane buses. The 380 Mbps data rate supports fast SPI links to ADCs and industrial Ethernet companion ICs, while direction control per 2-bit half lets one device serve both command and feedback buses. Industrial temperatures align with the -40C to +125C AEC-Q100 Grade 1 rating.
Рекомендуется
Microcontroller GPIO Level Shifting
General-purpose mixed-voltage MCU designs - from MSP430 (2.5 V) to 3.3 V peripherals - use the SN74AVC4T245QWRGYRQ1 for clean bidirectional GPIO translation. Unlike pass-switch solutions, its CMOS push-pull outputs maintain logic levels without external pull-ups, and the 2.1 ns delay adds negligible timing overhead. The VCCA-referenced DIR/OE pins simplify control since the controller side typically sets direction. Ioff protection ensures safe behavior when either rail collapses during reset, brownout, or programming sequences.
Рекомендуется
SPI Flash and Memory Interface Translation
Connecting 1.8 V processors to 3.3 V SPI flash memories requires translating SCLK, MOSI, MISO, and CS - exactly four signals matched by the SN74AVC4T245QWRGYRQ1's 4-bit width. With 380 Mbps capability, it sustains QSPI clock rates well above 80 MHz typical for fast flash reads. Splitting into two 2-bit halves allows independent direction control of command/address lines versus data lines. The 2.1 ns propagation delay keeps round-trip timing within SPI setup budgets even at elevated clock rates.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для SN74AVC4T245QWRGYRQ1 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | SN74AVC4T245RGYR | SN74AVC4T245QPWRQ1 | 74AVC4T245 (Nexperia) |
|---|---|---|---|---|
| Package | VQFN-16 (RGY) 4x3.5 mm | VQFN-16 (RGY) - same | TSSOP-16 (PW) - different | TSSOP-16 / DHVQFN-16 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Nexperia |
| Automotive Grade | Yes (AEC-Q100) | No | Yes (AEC-Q100) | No |
| Number of Bits | 4-bit | 4-bit | 4-bit | 4-bit |
| Supply Voltage Range | 1.2 V to 3.6 V (both supplies) | 1.2 V to 3.6 V | 1.2 V to 3.6 V | 1.2 V to 3.6 V |
| Output Type | 3-State | 3-State | 3-State | 3-State |
| Ioff Partial-Power-Down | Yes | Yes | Yes | Yes |
| Packaging Option | Tape & Reel (RGYRQ1) | Tape & Reel | Tape & Reel | Tape & Reel |
Ключевые отличия
- AEC-Q100 automotive qualification in VQFN-16 (против SN74AVC4T245RGYR)
- Compact 4x3.5 mm VQFN-16 footprint (против SN74AVC4T245QPWRQ1)
- Configurable as two independent 2-bit transceivers (против 74AVC4T245 (Nexperia))
Заметки по проектированию
Decouple VCCA and VCCB each with a 0.1 uF ceramic capacitor placed within 2 mm of the respective pins, connected to a solid ground plane. The VQFN-16 RGY package has a small exposed thermal pad - solder it to a ground pad array for both thermal relief and signal integrity. Since this is a dual-supply device, ensure both supply rails are present before enabling outputs, or rely on the Ioff feature during sequencing.
The DIR and OE control pins are referenced to VCCA, not VCCB - driving them from a VCCB-domain controller can violate input logic thresholds and cause bus contention. Always guarantee DIR is stable before data transitions, and use the OE pin (active low) to tri-state outputs during power-up, reset, or MCU reprogramming. Never leave OE floating; pull it up to VCCA if unused.
At data rates approaching 380 Mbps, keep A-side and B-side traces short (<50 mm) with controlled impedance where possible. Series termination of 22-33 ohm on B-side outputs reduces reflections on longer bus runs. Avoid routing translated signals adjacent to switching regulator nodes; the push-pull CMOS outputs are fast-edge devices (AVC family) and coupling into high-impedance neighboring traces can cause crosstalk glitches.
Do not exceed 3.6 V on either VCCA or VCCB - the absolute maximum is slightly higher but reliability degrades. When translating between rails derived from different regulators, account for sequenced power-up: if only one supply is present, Ioff circuitry holds outputs disabled and prevents backflow, but sustained operation in this state should be avoided in high-availability automotive systems.
Информация о соответствии
AEC-Q100 qualified per TI product page (Q suffix). RoHS compliant per TI product data. REACH and halogen-free status not stated in provided data.
