SN75116N - Differential Line Transceiver | Texas Instruments
Артикул: SN75116N ✓ АктивенSN75116N Обзор
A differential line transceiver is an interface IC that converts between single-ended TTL logic and a differential line signal. This signal hierarchy belongs to the broader sequence of transceiver, interface IC, semiconductor, and electronic communication systems. Differential signaling helps reject common-mode noise because the receiver evaluates the voltage difference between two conductors rather than one conductor referenced only to ground. The SN75116N therefore fits between a bus controller or terminal logic and a physical differential bus.
Key features include a single 5 V supply, TTL-compatible driver inputs, TTL-compatible receiver outputs, and a 3-state driver output that allows a connected node to release the bus when inactive. The integrated driver and receiver reduce the number of external interface components needed in a party-line topology. The 16-pin PDIP package also supports conventional through-hole assembly and prototyping workflows. Driver and receiver timing, propagation delay, and bus loading remain important system-level considerations when this device is added to an existing bus.
The SN75116N is intended for TTL-to-differential line conversion in party-line data buses. Its 3-state driver supports shared-bus arrangements, while the differential receiver improves noise immunity over a direct single-ended connection. Designers should account for propagation delay, bus termination, cable length, node stub effects, and the voltage margins required by the connected TTL devices. Because the device combines one driver and one receiver, system partitioning may require additional transceivers to balance each node's transmit and receive paths.
Typical uses include industrial control buses, instrumentation interfaces, point-to-point differential links, and legacy TTL equipment connected to balanced cabling. The device is also appropriate for laboratory prototypes and repair systems that need a straightforward 16-pin through-hole interface. In every case, the selected cables, connectors, grounding method, and logic family must preserve the voltage thresholds and signal timing expected by the bus.
A key implementation consideration is the receiver control function associated with this transceiver family. Confirm the exact control-pin behavior and timing from the manufacturer datasheet before substituting a related family member. When the PCB footprint must remain unchanged, the SN75116N should be treated as a design-specific component rather than replaced solely because another differential transceiver has similar headline features.
This page combines the manufacturer's product identity, exact ordering package, commercial sourcing path, functional comparisons, and practical interface-design guidance. It also identifies where timing, pin-level, compliance, and alternative-device details require direct verification before schematic release or PCB reuse.
Аналоги без доработки для SN75116N — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с SN75116N (тот же форм-фактор и посадочное место) — отличается по Mounting Type, Operating Temperature Range, Package, Primary Application, Product Type.
SN75118N
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →SN55116N
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
SN75116N Характеристики
| Device Type | Single differential line transceiver |
| Transceiver Configuration | 1 transmitter and 1 receiver |
| Напряжение питания | 5 V |
| Driver Input Compatibility | TTL-compatible |
| Receiver Output Compatibility | TTL-compatible |
| Driver Output State | 3-state |
| Signal Type | Differential line |
| Primary Application | Party-line and data-bus communication |
| Package Type | 16-pin PDIP |
| Число выводов | 16 pins |
| Тип монтажа | Through-hole |
| Диапазон рабочих температур | 0 °C to 70 °C |
Руководство по цоколевке SN75116N в корпусе 16-pin pdip
Цоколевка для SN75116N (корпус 16-pin pdip). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для SN75116N.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
SN75116N подходит для 6 применениеs: Legacy TTL Party-Line Data Bus, TTL-to-Differential Instrumentation Interface, Industrial Control Bus Interface, Point-to-Point Balanced Data Link, Laboratory Data Acquisition Backplane, Legacy Equipment Repair and Retrofit.
Legacy TTL Party-Line Data Bus
The SN75116N fits a legacy party-line bus because it combines one 3-state differential driver and one receiver in a single 5 V package. The driver can place the line in a high-impedance state when the node is inactive, while the receiver recovers the differential signal as a TTL-compatible logic output. This arrangement reduces the external component count for equipment that shares one bus among multiple nodes. The designer must verify termination, node stub length, receiver-control polarity, and propagation delay against the actual bus timing before installation.
Рекомендуется
TTL-to-Differential Instrumentation Interface
The SN75116N can bridge TTL instrumentation logic and a balanced data line when noise immunity and bus participation are more important than compact packaging. Its single 5 V supply matches many legacy digital systems, and the TTL-compatible driver inputs and receiver outputs simplify the digital boundary. Place the transceiver near the line connector to minimize unbalanced stub length, then validate grounding, cable termination, logic thresholds, and signal timing under the worst-case noise and loading conditions.
Рекомендуется
Industrial Control Bus Interface
The SN75116N is appropriate for a 5 V industrial control interface that uses differential line signaling and conventional TTL logic. The 3-state driver permits controlled connection to a shared bus, and the differential receiver helps reduce susceptibility to common-mode noise found near control equipment. Its specified 0 to 70 °C range must remain within the enclosure's temperature limits. Validate isolation strategy, surge exposure, cable length, termination, and grounding before using the device on long industrial wiring.
Рекомендуется
Point-to-Point Balanced Data Link
For a short point-to-point link, the SN75116N provides a straightforward path from TTL logic to a differential pair and back to TTL-compatible logic. The 16-pin PDIP format simplifies assembly on legacy or prototype boards, while its integrated driver and receiver reduce board area compared with separate line-driver and receiver devices. Keep both logic-side traces short and away from the cable connection, observe the manufacturer's output and receiver thresholds, and confirm that the selected cable and termination method satisfy the target data rate.
Рекомендуется
Laboratory Data Acquisition Backplane
The SN75116N can connect laboratory acquisition hardware to a shared differential backplane when the system operates from 5 V and uses TTL-compatible control signals. The receiver provides a convenient single-ended logic output, while the 3-state driver allows an instrument or peripheral to join or leave the bus selectively. Through-hole packaging is useful for prototype and repair platforms. Establish a defined reference ground, use controlled bus impedance, minimize connectors and stubs, and test every node for contention before beginning data acquisition.
Рекомендуется
Legacy Equipment Repair and Retrofit
The SN75116N is well suited to repairing or retrofitting older equipment that uses a 16-pin PDIP differential transceiver. The through-hole package supports conventional soldering and socket-based diagnostics, while the 5 V supply and TTL-compatible logic levels align with many vintage bus designs. Before installing it, compare the complete pin-description table, control polarity, propagation delays, receiver thresholds, and output-state behavior with the failed device. A working substitute must match the original electrical role, not merely the transceiver description.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для SN75116N — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | SN75118N | SN55116N |
|---|---|---|---|
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Type | Differential line transceiver | Differential line transceiver | Differential line transceiver |
Ключевые отличия
- Matches the established 16-pin through-hole party-line interface (против SN75118N)
- Provides the specified commercial temperature grade for legacy equipment (против SN55116N)
- Combines a 3-state driver and receiver in one package (против SN75118N)
Заметки по проектированию
Place the SN75116N close to the differential-line connector and keep the two line conductors as a routed pair. Minimize the distance between the transceiver line pins and the connector, avoid stubs, and keep the unbalanced TTL-side traces away from the cable exit. Confirm that the PCB provides the exact 16-pin PDIP footprint and verify every numbered pin against the Texas Instruments datasheet before fabrication.
Do not treat a related SN75116-family IC as interchangeable without checking receiver-control polarity and timing. The SN75116N uses a receiver-output-strobe arrangement, while the SN75118N family member uses an enable function. Also avoid assuming that a surface-mount ordering suffix is a drop-in replacement: package drawings, land patterns, and assembly requirements differ between PDIP and surface-mount options.
Define the bus topology, characteristic impedance, termination method, maximum cable length, and permitted stub length before layout. Use a 3-state strategy that prevents multiple nodes from driving the line simultaneously. Verify propagation delay, receiver thresholds, and logic setup time against the slowest attached device, particularly when the transceiver sits between physically separated nodes.
Route the 5 V supply and ground connections directly to the transceiver with minimal loop area, and place the manufacturer's recommended bypass capacitor close to the device. Use the datasheet's absolute maximum and recommended operating conditions as the electrical limits. If the transceiver is mounted near long cables or switching equipment, assess common-mode voltage, ground offset, and ESD protection at the connector rather than assuming logic-level protection is sufficient.
Информация о соответствии
The legacy SN75116 family is an interface IC rather than an automotive-qualified product. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations must be confirmed from the current Texas Instruments product or material-compliance documentation.