MaxLinear

SP3232EBCP-L - 250kbps Dual RS-232 Transceiver | MaxLinear

Артикул: SP3232EBCP-L ✓ Активен
3.0 V to 5.5 V Vdss 0.3 mA Id True EIA/TIA-232-F operation Rds(on) 28-pin LQFP Package
MOQ: 1 |

SP3232EBCP-L Обзор

The MaxLinear SP3232EBCP-L is a dual RS-232 transceiver integrated circuit with two transmitters, two receivers, a 250 kbps data rate, and a single-supply operating range of 3.0 V to 5.5 V. It is packaged in a 28-pin LQFP. The device provides true EIA/TIA-232-F operation and uses a charge-pump power supply with four external 0.1 µF capacitors.

An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 bipolar levels and converts incoming RS-232 signals back into digital logic. RS-232 belongs to the interface-IC hierarchy and is commonly used for point-to-point serial links in computer, industrial-control, instrumentation, and embedded systems. Its differential bipolar signaling provides noise immunity and voltage margins suited to cable-based communication.

The SP3232EBCP-L offers two transmit channels and two receive channels, allowing one integrated component to handle bidirectional serial communication. Its 250 kbps rated transmission rate supports substantially faster data transfer than legacy limited-rate serial interfaces. Operation from a single 3.0 V to 5.5 V supply also allows the same circuit to work with 3.3 V and 5 V system rails.

Its charge-pump circuitry generates the positive and negative voltage levels required by true RS-232 operation. Four external 0.1 µF capacitors support the charge pump and associated voltage generation. According to the MaxLinear SP3232EB family information, the charge-pump architecture requires only 0.1 µF capacitors for 3.3 V operation, helping reduce board area while preserving compliant line-driver levels.

Typical applications include industrial serial controllers, portable data-acquisition equipment, computer peripherals, instrument interfaces, and embedded systems that exchange RS-232 commands or data. The two transmitters and two receivers are useful where a device must support more than one serial channel or provide separate transmit and receive connections on each port.

PCB design should place the four charge-pump capacitors close to their associated pins, preserve the recommended routing geometry, and provide uninterrupted ground-plane continuity beneath the device. Check that the host interface uses the correct RS-232 logic levels and cable connection because the SP3232EBCP-L does not directly accept TTL signals without the transceiver’s level translation.

This product record combines the SP3232EB family specifications with practical interface-selection guidance, including same-footprint alternatives, charge-pump layout considerations, application fit, and a parameter-by-parameter comparison for engineering review.

Аналоги без доработки для SP3232EBCP-L — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с SP3232EBCP-L (тот же форм-фактор и посадочное место) — отличается по Data Rate, Mounting Type, Package, Packaging, RoHS Status.

MaxLinear
Data Rate: 250 kbps (under load)
Package: 20-TSSOP (Y), 4.40 mm body width
Packaging: Tape & Reel (TR)
MaxLinear
Data Rate: 250 kbps under load
Mounting Type: Surface mount (SMD/SMT)
Packaging: Tape and reel (TR)

SP3222EBEY-L/TR

✅ Прямая замена
MaxLinear
📦 28-pin LQFP
RS-232 Transceiver (2 drivers / 2 receivers) · RS-232 (EIA/TIA-232-F compliant) · 3.0 V to 5.5 V · 250 kbps (under load) · 2 · 2 · 1 µA (receivers active, SP3222EB)

Уточнить цену

Открыть даташит →

SP3232EBCN-L/TR

✅ Прямая замена
MaxLinear
📦 28-pin LQFP
2/2 · Full duplex RS-232 transceiver · 3 V to 5.5 V · 250 kbps under load · 15 kV on RS-232 pins · True EIA/TIA-232-F · On-chip charge pump, single supply · 0.1 uF per pump node

✓ В наличии

$0.7711 / шт.

Открыть даташит →

SP3232EBCP

✅ Прямая замена
📦 28-pin LQFP
Electrical ratings match at 0% difference; the -L suffix distinguishes the requested configuration

📋 Справочный аналог (нет в каталоге)

SP3222EBCP

✅ Прямая замена ⚠️ Характеристики не проверены
📦 28-pin LQFP
2 TX, 2 RX, 250 kbps, and supply voltage match at 0% difference; shutdown behavior differs

📋 Справочный аналог (нет в каталоге)

SP3232EBCP-L Характеристики

Product Type RS-232 transceiver
Number of Transmitters 2
Number of Receivers 2
Скорость передачи данных 250 kbps
Supply Voltage Range 3.0 V to 5.5 V
Typical Supply Current 0.3 mA
Internal Charge Pump Yes
Number of External Capacitors 4
Nominal External Capacitor Value 0.10 µF
RS-232 Standards Compliance True EIA/TIA-232-F operation
Power Supply Type Single supply
Корпус 28-pin LQFP
Тип монтажа Surface mount
Receiver Shutdown Current 1 µA for SP3222EB

Руководство по цоколевке SP3232EBCP-L в корпусе 28-pin lqfp

Цоколевка для SP3232EBCP-L (корпус 28-pin lqfp). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.

Схема цоколевки корпуса 28-pin lqfp для SP3232EBCP-L

Нет подробных данных о распиновке для SP3232EBCP-L.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

SP3232EBCP-L подходит для 6 применениеs: Industrial Serial Control, Portable Data Acquisition, Computer Peripherals, Test and Measurement Instruments, Embedded Serial Bridges, Network and Communication Equipment.

🏭

Industrial Serial Control

The SP3232EBCP-L fits industrial control equipment that requires two RS-232 channels for command, status, and configuration links. Its two transmitters and two receivers provide balanced channel density in a single 28-pin LQFP, while the 250 kbps capability supports responsive device communication. Operating from 3.0 V to 5.5 V permits use with either 3.3 V control electronics or 5 V legacy equipment. The internal charge pump and four 0.1 µF capacitors simplify the bipolar voltage generation required for true EIA/TIA-232-F operation.

📱

Portable Data Acquisition

Portable instruments and data-acquisition units can use the SP3232EBCP-L to communicate with a host computer over RS-232. The 250 kbps rate provides sufficient throughput for command traffic, sampled status data, and configuration transfers, while the single 3.0 V to 5.5 V supply reduces the number of external rails needed in compact equipment. Its integrated charge pump generates the required positive and negative RS-232 levels using only four 0.1 µF external capacitors, conserving board area in portable designs.

🖥️

Computer Peripherals

The SP3232EBCP-L is appropriate for legacy computer peripherals that communicate through an RS-232 port. Two transmitters and two receivers allow separate transmit and receive paths, and the 250 kbps transmission rate supports conventional serial-control protocols. Its ability to operate from either 3.3 V or 5 V assists designers bridging modern embedded controllers with established RS-232 equipment. True RS-232 output levels are produced by the internal charge pump, but the host connector still requires the correct bipolar signal and ground wiring.

🔧

Test and Measurement Instruments

The SP3232EBCP-L can provide the serial interface in analyzers, calibrators, and laboratory instruments that exchange commands or measurement records with a controller. Two channels reduce the external interface-component count when both command and data paths are required, and the 250 kbps rate supports moderate-rate telemetry. The 3.0 V to 5.5 V supply range simplifies integration with mixed-voltage test equipment, while the internal charge pump avoids a separate bipolar supply generator.

🧩

Embedded Serial Bridges

The SP3232EBCP-L is useful in embedded systems that must translate a host UART into a fully compliant RS-232 connection. A microcontroller can manage the serial protocol while the transceiver handles bipolar level conversion and charge-pump voltage generation. The 250 kbps rate is suitable for many control, bootloader, and telemetry protocols, and the two-channel arrangement supports two independent links. Because the device accepts logic-level signaling internally, careful grounding and cable selection remain essential for reliable communication.

🌐

Network and Communication Equipment

RS-232 is still common in network-management equipment, console servers, and specialized communication modules, and the SP3232EBCP-L can provide two interface channels for equipment control. Its 250 kbps rating accommodates console, status, and configuration traffic, while the single-supply operation simplifies integration into systems using either 3.3 V or 5 V logic. The internal charge pump provides the positive and negative voltage levels required for true RS-232, although long cable runs and electrically noisy installations should be evaluated for signal-integrity margin.

Сводка рекомендуемых товаров

SP3232EB Same-family RS-232 transceiver Используется в: Industrial Serial Control, Portable Data Acquisition, Computer Peripherals, Embedded Serial Bridges SP3222EBCP Low-power same-package family alternative Используется в: Industrial Serial Control, Test and Measurement Instruments, Network and Communication Equipment SP3232EBCP Base ordering code in the same transceiver family Используется в: Portable Data Acquisition, Test and Measurement Instruments, Network and Communication Equipment SP3222EB Pin-compatible RS-232 family member Используется в: Computer Peripherals, Embedded Serial Bridges
What is the operating voltage range of SP3232EBCP-L?
The SP3232EBCP-L operates from a single 3.0 V to 5.5 V supply. According to the MaxLinear SP3232EB family information, the charge-pump design can operate from a single low-voltage supply and requires only 0.1 µF external capacitors in 3.3 V operation. This makes the interface suitable for both 3.3 V and 5 V embedded systems while producing the bipolar voltage levels needed for true RS-232 communication.
What are the key specifications of SP3232EBCP-L that engineers should know?
The SP3232EBCP-L is a 250 kbps RS-232 transceiver with two transmitters and two receivers in a 28-pin LQFP. It operates from 3.0 V to 5.5 V and supports true EIA/TIA-232-F operation. Its charge-pump supply uses four external 0.1 µF capacitors, while typical supply current is 0.3 mA. These specifications define its core suitability for compact, low-voltage serial-interface equipment.
How many RS-232 transmitters and receivers does SP3232EBCP-L contain?
The SP3232EBCP-L contains two RS-232 transmitters and two RS-232 receivers. According to the SP3232EB family information, this arrangement supports two communication channels or paired bidirectional links while reducing the number of interface components required on a PCB. Each transmitter creates bipolar RS-232 levels, while each receiver converts those bipolar levels into digital signals for the host controller.
Where can I download the SP3232EBCP-L datasheet PDF?
The official SP3232EB product information is available from MaxLinear, and the related SP3232EBCP datasheet can be located through the manufacturer’s interface-product resources. Use the manufacturer datasheet for the authoritative pin-description table, capacitor values, recommended layout, electrical characteristics, and package drawings. The distributor-hosted PDF mirror is also indexed, but the manufacturer’s page provides the most appropriate starting point for current technical documentation.
Where can I find the SP3232EBCP-L pinout?
The SP3232EBCP-L pinout is found in the pin-description table and package drawing of the manufacturer datasheet for the 28-pin LQFP version. Assign PCB nets directly from that table rather than relying on a generic RS-232 transceiver diagram, because related family members can differ in enable, shutdown, and receiver-active functions. The numbered package drawing must be cross-checked against the exact ordering code before fabrication.
What can replace SP3232EBCP-L?
SP3222EBCP is the closest same-family option identified for direct evaluation because it uses the same 28-pin LQFP format and retains two transmitters, two receivers, a 250 kbps data rate, and a 3.0 V to 5.5 V supply range. The SP3222EB family also specifies 1 µA shutdown current with receivers active, while the SP3232 family emphasizes true RS-232 performance and 250 kbps transmission. Verify shutdown and enable behavior against the manufacturer datasheet before release.
Is SP3232EBCP-L suitable for industrial serial interfaces?
The SP3232EBCP-L is suitable for industrial serial interfaces when the link uses RS-232 levels and does not require longer-distance, isolated communication. Its 250 kbps rate and true EIA/TIA-232-F operation suit equipment-control and data-acquisition links. The exact operating-temperature limits and product qualification status must be confirmed from the ordering-code documentation before deployment in temperature-extreme or regulated environments.
SP3232EBCP-L vs SP3222EBCP - which is better for a 250 kbps link?
Choose the SP3232EBCP-L when the design specifically requires the SP3232EB family’s true RS-232 performance and 250 kbps operating position. The SP3222EBCP retains the same 2-transmitter, 2-receiver arrangement, 250 kbps rate, 3.0 V to 5.5 V supply range, and 28-pin LQFP footprint, while the SP3222EB family is distinguished by a specified 1 µA shutdown mode with receivers active. Both require a final datasheet comparison of enable and shutdown behavior.
When should I choose SP3232EBCP-L over SP3232EBCP?
Choose SP3232EBCP-L when the required procurement configuration specifically includes the -L ordering suffix, while SP3232EBCP otherwise represents the base ordering code for the same core transceiver family. Both are associated with a 28-pin LQFP implementation, two transmitters, two receivers, a 250 kbps data rate, and a 3.0 V to 5.5 V supply. Confirm the manufacturer’s ordering table for the exact finish, marking, and shipment configuration.
Is SP3232EBCP-L in stock and what is its lead time?
Current stock and production lead time for SP3232EBCP-L should be requested through the Request a Quote form on this page. The manufacturer identifies the SP3232EB family, but the exact -L configuration requires a configuration-specific availability check. Request the current lot status, minimum order quantity, package quantity, and delivery schedule when placing the order.
What is the price of SP3232EBCP-L?
Use the Request a Quote form on this page to obtain the current SP3232EBCP-L quotation and volume availability. The quote should specify the exact -L ordering code, package quantity, delivery schedule, and destination. Because the device is also offered under the SP3232EB family, confirm that the quotation line item matches the 28-pin LQFP configuration rather than another member of the broader transceiver range.
Where can I buy SP3232EBCP-L online?
The SP3232EBCP-L can be requested through the Request a Quote form on this product page. Include the exact manufacturer part number SP3232EBCP-L so the supplier can confirm the 28-pin LQFP configuration, current production status, and delivery schedule. Buyers should also state their required quantity and packaging preference to receive an actionable quotation.
How should the four charge-pump capacitors be placed around SP3232EBCP-L?
Place the four 0.1 µF charge-pump capacitors close to the pins specified in the manufacturer’s recommended layout. Keep each capacitor’s connection short, preserve the return path to the associated ground or supply pin, and avoid routing charge-pump nodes beneath long traces or noisy switching stages. According to the MaxLinear SP3232EB family information, the charge-pump approach requires only 0.1 µF capacitors for 3.3 V operation.
Does SP3232EBCP-L need external RS-232 voltage generation?
The SP3232EBCP-L does not require an external RS-232 voltage generator because it includes an internal charge pump. Four external 0.1 µF capacitors support the charge-pump circuitry. The generated bipolar voltage levels allow the transmitters to meet true RS-232 requirements from a single 3.0 V to 5.5 V supply. Follow the manufacturer’s polarity and capacitor-placement requirements exactly to preserve signal integrity.
What is the best MaxLinear equivalent for SP3232EBCP-L?
The closest identified MaxLinear-family equivalent is SP3222EBCP, which uses the same 28-pin LQFP configuration and preserves the 2-transmitter, 2-receiver arrangement, 250 kbps rate, and 3.0 V to 5.5 V operating range. Its principal distinction is the SP3222EB family’s specified 1 µA shutdown behavior with receivers active. Use the SP3232EBCP-L when its established SP3232 family configuration is preferred and SP3222EBCP when its power-saving behavior is advantageous.

Справочные инженерные данные для SP3232EBCP-L — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose SP3232EBCP-L when the design specifically calls for the SP3232EB family in a 28-pin LQFP configuration with two transmitters, two receivers, 250 kbps operation, and a single 3.0 V to 5.5 V supply. SP3232EBCP is the base ordering code with matching core electrical ratings and should be selected when its manufacturing or marking configuration is preferable. SP3222EB is appropriate when its specified 1 µA shutdown current with receivers active is more useful than the SP3232 family emphasis. SP3222EBCP provides the same channel count, data rate, supply range, package, and capacitor count but shifts the shutdown emphasis. Before substitution, compare enable behavior, receiver-active shutdown state, logic thresholds, operating temperature, qualification status, and exact pin names in the manufacturer documentation.

Сравнение с аналогами

Параметр Этот товар SP3222EB SP3232EB SP3232EBCP SP3222EBCP
Package 28-pin LQFP 28-pin LQFP 28-pin LQFP 28-pin LQFP 28-pin LQFP
Brand MaxLinear, Inc. MaxLinear, Inc. MaxLinear, Inc. MaxLinear, Inc. MaxLinear, Inc.
Number of Transmitters 2 2 2 2 2
Number of Receivers 2 2 2 2 2
Data Rate 250 kbps 250 kbps 250 kbps 250 kbps 250 kbps
Supply Voltage Range 3.0 V to 5.5 V 3.0 V to 5.5 V 3.0 V to 5.5 V 3.0 V to 5.5 V 3.0 V to 5.5 V
External Capacitors 4 × 0.1 µF 4 × 0.1 µF 4 × 0.1 µF 4 × 0.1 µF 4 × 0.1 µF
Ordering Suffix -L Family code Family code Base ordering code Base ordering code

Ключевые отличия

  • Two full-duplex RS-232 channels in one device (против SP3222EBCP)
  • True RS-232 performance at 250 kbps (против SP3222EB)
  • Single 3.0 V to 5.5 V operation (против SP3232EBCP)
  • Compact charge-pump implementation (против SP3222EBCP)

Заметки по проектированию

Place all four 0.1 µF charge-pump capacitors as close as practical to their associated SP3232EBCP-L pins. Keep capacitor loops compact and route the grounded terminals directly to the associated ground pins. Avoid placing sensitive analog or high-speed digital traces beneath charge-pump switching nodes. The MaxLinear SP3232EB family uses this four-capacitor arrangement, making placement geometry an important part of preserving transmitter performance.

Do not treat the SP3232EBCP-L as a TTL-to-RS-232 logic substitute with interchangeable enable and shutdown functions. Related SP3222EB and SP3232EB devices can differ in power-saving behavior, so assign every input after checking the exact manufacturer pin-description table. Also verify connector polarity: an incorrectly wired RS-232 interface can produce negative driver voltages on receiver inputs despite a correct PCB footprint.

Maintain a continuous ground reference beneath the LQFP and minimize loop area around the charge-pump network. Separate the interface from switching power stages and high-current return paths, and use a solid plane rather than fragmented ground traces. If the board also supports other communications interfaces, keep the RS-232 connector-side protection and cable routing away from sensitive analog inputs to reduce transient and ground-bounce coupling.

The SP3232EBCP-L operates from a single 3.0 V to 5.5 V supply, but its charge-pump and line-driver circuitry still require clean decoupling and correct capacitor tolerances. Place the recommended local supply bypass capacitor near the supply pins and follow the manufacturer’s voltage and capacitance requirements. Confirm that the host logic voltage matches the transceiver’s digital input and output thresholds rather than assuming compatibility from the connector interface alone.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

No product-specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified. The -L ordering suffix should be checked against the manufacturer ordering table before making a compliance claim.

Данные проверены: 2026-11-10 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

SP3232EBCP-L datasheet SP3232EBCP-L specifications SP3232EBCP-L pinout SP3232EBCP-L datasheet pdf SP3232EBCP-L equivalent SP3232EBCP-L replacement SP3232EBCP-L price SP3232EBCP-L stock MaxLinear SP3232EBCP-L SP3232EBCP-L 28 pin LQFP SP3232EBCP-L 250 kbps SP3232EBCP-L vs SP3222EBCP SP3232EBCP-L charge pump layout SP3232EBCP-L RS-232 interface

Связанные компоненты & термины

MaxLinear, Inc. SP3232EBCP-L SP3232EB SP3232EBCP SP3222EB SP3222EBCP RS-232 transceiver interface IC serial transceiver EIA/TIA-232-F charge pump 250 kbps 3.0 V to 5.5 V 28-pin LQFP LQFP family surface mount SMD RS-232 transmitter RS-232 receiver single-supply operation external capacitor bipolar signal industrial serial interface portable data acquisition embedded serial bridge
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ