Texas Instruments

THS6182PWP - Low-Power ADSL Line Driver | Texas Instruments

Артикул: THS6182PWP ✓ Активен
5 V to 15 V Vdss 11 mA per channel Id 20-pin HTSSOP with exposed pad, 4.40 mm body width Package
MOQ: 1 |

THS6182PWP Обзор

The Texas Instruments THS6182PWP is a low-power differential ADSL and power-line communications line driver with one transmitter, operating from a 5 V to 15 V supply in a 20-pin HTSSOP package with an exposed pad. It provides four selectable bias modes, low total harmonic distortion of -88 dBc at 100 kHz and 1 MHz, and can drive the line at +20 dBm while maintaining -76 dBc distortion with the high-bias setting.

An ADSL line driver is an interface IC that converts a low-amplitude differential source signal into a high-current differential output suitable for transmission over telephone-line copper. This device belongs to the broader line-driver and transmitter hierarchy, within interface ICs and communication semiconductors. Its architecture is designed to increase line-card density by reducing quiescent current and power dissipation while maintaining the linearity required for full-rate ADSL systems.

The THS6182PWP supports full-bias, mid-bias, low-bias, and shutdown operating modes. The advertised channel-current settings are 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. An ADJ pin allows user-controlled bias current, and operation remains stable down to 1.8 mA per channel.

Signal-chain performance is centered on low distortion and low noise. The manufacturer lists total harmonic distortion of -88 dBc at 100 kHz and 1 MHz, while the high-bias configuration can drive +20 dBm on the line with -76 dBc distortion. The input current-noise density is listed as 3.2 nV per square hertz. These characteristics are relevant to receiver sensitivity because distortion and noise introduced at the line-driver stage can reduce the usable margin of the downstream receiver.

Typical applications include full-rate ADSL line cards, central-office ADSL equipment, power-line communication transmitters, and other copper-pair interfaces requiring differential current-drive capability. The adjustable bias architecture supports different line lengths, launch-power requirements, and system power budgets. A high-bias setting provides greater drive level when line loss is severe, while the lower-current modes reduce dissipation where adequate reach or signal level is not required.

PCB implementation requires attention to the exposed thermal pad, supply decoupling, high-current return paths, and controlled-impedance differential routing. Keep the driver close to the transformer or line-coupling network, minimize loop area in output-current paths, and use the manufacturer-recommended power and ground-plane construction to limit parasitic inductance. The exposed pad must be connected to the ground plane for both electrical return and heat dissipation.

This page consolidates the manufacturer specifications, package details, application guidance, and verified cross-reference information for engineers evaluating the THS6182PWP. It also identifies why a mechanically and electrically identical replacement should not be assumed from a similar line-driver description. Use the Texas Instruments THS6182 datasheet for the final pin assignments, recommended application circuit, exposed-pad layout, and electrical characteristics before releasing a PCB.

Аналоги без доработки для THS6182PWP — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Для этого товара нет аналогов без доработки.

Запросить аналоги

THS6182PWP Характеристики

Product Type Differential ADSL line driver
Number of Drivers 1 driver
Number of Receivers 0 receivers
Supply Voltage Range 5 V to 15 V
Total Harmonic Distortion -88 dBc at 100 kHz and 1 MHz
High-Bias Line Output +20 dBm with -76 dBc distortion
Full-Bias Current 11 mA per channel
Mid-Bias Current 7.5 mA per channel
Low-Bias Current 4 mA per channel
Ток выключения 0.25 mA per channel
Input Current-Noise Density 3.2 nV/sqrt(Hz)
Minimum Stable Bias Current 1.8 mA per channel
Bias Adjustment User-controlled through ADJ pin
Корпус 20-pin HTSSOP with exposed pad, 4.40 mm body width
Packaging Tube
Тип монтажа Surface mount

Руководство по цоколевке THS6182PWP в корпусе 20-pin htssop with exposed pad, 4.40 mm body width

Цоколевка для THS6182PWP (корпус 20-pin htssop with exposed pad, 4.40 mm body width). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.

Схема цоколевки корпуса 20-pin htssop with exposed pad, 4.40 mm body width для THS6182PWP

Нет подробных данных о распиновке для THS6182PWP.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

THS6182PWP подходит для 6 применениеs: Full-Rate ADSL Line Cards, Central-Office ADSL Equipment, Power-Line Communication Transmitters, Digital Subscriber Line Access Multiplexer, Copper-Pair Communication Interfaces, Low-Power Line Interface Modules.

🌐

Full-Rate ADSL Line Cards

The THS6182PWP fits a full-rate ADSL transmitter because it combines a dedicated differential driver with selectable bias currents of 11 mA, 7.5 mA, or 4 mA per channel. According to the Texas Instruments THS6182 datasheet, its low-power design supports higher line-card density, while -88 dBc distortion at 100 kHz and 1 MHz helps preserve transmission linearity. Place the device near the line-coupling transformer, use the recommended exposed-pad ground pattern, and select the bias mode that provides adequate reach without unnecessary line-card dissipation.

🖥️

Central-Office ADSL Equipment

Central-office line-card designs benefit from the THS6182PWP because low dissipation allows more channels to be placed in a limited rack space. Its four operating states provide a practical power budget: 11 mA per channel for full bias, 7.5 mA for mid bias, 4 mA for low bias, and 0.25 mA in shutdown. The Texas Instruments THS6182 datasheet also specifies operation down to 1.8 mA per channel, enabling designers to tune line current for reach, linearity, and thermal requirements.

🔌

Power-Line Communication Transmitters

The THS6182PWP is suitable for a power-line communication output stage because Texas Instruments describes it as an ADSL and PLC line driver. Its differential architecture drives a line-coupling network, while the ADJ pin provides user-controlled bias current for matching different cable lengths and network conditions. The listed +20 dBm high-bias capability and -76 dBc distortion offer a concrete starting point for link-budget and signal-integrity evaluation, with the tradeoff that higher bias current increases board power dissipation.

📡

Digital Subscriber Line Access Multiplexer

A DSL access multiplexer can use the THS6182PWP at the line interface to create a high-current differential drive signal from the system transmitter. Its low quiescent dissipation is valuable when many subscriber ports share one line card, while selectable bias modes let designers optimize each port's launch power. The -88 dBc distortion specification supports high-linearity operation, but the output network, transformer, impedance, and routing must be evaluated as a complete signal path rather than in isolation.

🔗

Copper-Pair Communication Interfaces

The THS6182PWP can serve as the transmitter in equipment that sends differential current signals over copper pairs. Its 5 V to 15 V operating range supports conventional line-card supply architectures, and the four bias modes permit a single platform to cover short and long reaches. According to the Texas Instruments THS6182 datasheet, the 3.2 nV/sqrt(Hz) input current-noise density and low THD are particularly relevant when preserving receiver sensitivity and maintaining margin through the line interface.

⚡

Low-Power Line Interface Modules

The THS6182PWP supports compact line-interface modules where standby power and channel count are important constraints. Shutdown mode reduces the listed current to 0.25 mA per channel, while low-bias and mid-bias settings provide intermediate operating points. The Texas Instruments THS6182 datasheet indicates stable operation down to 1.8 mA per channel, giving hardware designers several control points for managing energy use while maintaining the differential line output required by ADSL or PLC equipment.

Сводка рекомендуемых товаров

THS6182PWP Texas Instruments Используется в: Full-Rate ADSL Line Cards, Central-Office ADSL Equipment, Power-Line Communication Transmitters, Digital Subscriber Line Access Multiplexer, Copper-Pair Communication Interfaces, Low-Power Line Interface Modules THS6182DWR Texas Instruments Используется в: Full-Rate ADSL Line Cards, Digital Subscriber Line Access Multiplexer, Low-Power Line Interface Modules EL1503C Pin-compatible line-driver family referenced by the manufacturer Используется в: Central-Office ADSL Equipment, Copper-Pair Communication Interfaces EL1508C Pin-compatible line-driver family referenced by the manufacturer Используется в: Power-Line Communication Transmitters
What is the THS6182PWP and what does it do?
The THS6182PWP is a Texas Instruments low-power differential ADSL and power-line communication line driver with one transmitter and no receiver. According to the Texas Instruments THS6182 datasheet, it operates from 5 V to 15 V, provides selectable bias modes, and is intended for full-rate ADSL systems where reduced power dissipation helps increase line-card density.
What are the key specifications of THS6182PWP that engineers should know?
The THS6182PWP combines a 5 V to 15 V supply range, four bias modes, and a 20-pin HTSSOP exposed-pad package in one ADSL line-driver IC. According to the Texas Instruments THS6182 datasheet, the principal performance figures include -88 dBc total harmonic distortion at 100 kHz and 1 MHz, 3.2 nV/sqrt(Hz) input current-noise density, and operation down to 1.8 mA per channel.
Where can I download the THS6182PWP datasheet PDF?
The official Texas Instruments THS6182 product page provides the manufacturer datasheet and supporting technical documentation. The document is identified by the manufacturer as the THS6182 data sheet, revision H. Use the manufacturer copy for pin names, recommended application circuits, electrical limits, exposed-pad layout, and operating guidance before finalizing the design.
Where can I find the THS6182PWP pinout?
The THS6182PWP pinout is documented in the Texas Instruments THS6182 data sheet, revision H, and corresponds to the 20-pin HTSSOP outline with an exposed thermal pad. Use the pin-description table and package drawing from that document to assign PCB nets, particularly the supply, ground, differential input, ADJ, and output connections.
How much current does the THS6182PWP use in each bias mode?
The THS6182PWP offers 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. According to the Texas Instruments THS6182 datasheet, these settings let the equipment designer trade line-drive capability and signal margin against power dissipation.
What distortion and output level can the THS6182PWP achieve?
The THS6182PWP is rated for -88 dBc total harmonic distortion at 100 kHz and 1 MHz under the manufacturer's stated conditions. According to the Texas Instruments THS6182 datasheet, its high-bias setting can drive the line at +20 dBm while maintaining -76 dBc distortion, providing a useful reference when sizing output power and receiver margin.
When should I choose the THS6182PWP over another ADSL line driver?
Choose the THS6182PWP when the design requires a dedicated one-channel differential ADSL transmitter, selectable full-, mid-, low-, or shutdown bias, and operation from a 5 V to 15 V supply. It is especially relevant to full-rate ADSL line cards where low power dissipation supports high-density central-office equipment and the ADJ pin provides control over bias current.
Is the THS6182PWP suitable for power-line communication equipment?
Yes, the THS6182PWP is suitable for power-line communication transmitters that require a differential high-current line output. According to the Texas Instruments product documentation, the device is described as a low-power ADSL and PLC line driver, with a supply range of 5 V to 15 V and user-adjustable bias for balancing output drive against system power consumption.
THS6182PWP vs THS6182DWP: which package should I choose?
The THS6182PWP and THS6182DWP belong to the same THS6182 family but use different TI package suffixes, so they are not automatically drop-in equivalents for a fixed PCB. The THS6182PWP is specified as a 20-pin HTSSOP with exposed pad, whereas the DWP ordering code must be checked against its own package drawing. Confirm the land pattern and every exposed-pad connection before exchanging them.
Can EL1503C or EL1508C replace the THS6182PWP?
The Texas Instruments THS6182 documentation states that the device is pin compatible with EL1503C and EL1508C, but the cross-reference alone does not establish that every package variant is mechanically identical. The THS6182PWP uses a 20-pin HTSSOP with an exposed pad, so confirm the candidate package, exposed-pad dimensions, pin functions, and thermal requirements before approving a board-level substitution.
What is the best drop-in replacement for THS6182PWP?
No verified drop-in replacement is established for the exact THS6182PWP package and pin configuration in the available cross-reference information. Texas Instruments identifies the EL1503C and EL1508C as pin-compatible, but package equality must still be demonstrated. Until the land pattern, exposed pad, bias-control interface, and electrical limits are confirmed, treat these candidates as qualified alternatives rather than guaranteed drop-ins.
What can replace the THS6182PWP on an existing PCB?
A safe PCB replacement must have the same 20-pin HTSSOP land pattern, pin functions, exposed-pad connection, supply range, bias modes, and compatible drive current. According to the Texas Instruments THS6182 documentation, EL1503C and EL1508C offer pin compatibility, but the mechanical and electrical requirements still need verification. Do not select a replacement solely from the line-driver description or package name.
How should the THS6182PWP exposed pad be connected on a PCB?
Connect the exposed pad to the ground plane using the land pattern and thermal-via arrangement specified by Texas Instruments. The pad provides a low-impedance return path and conducts heat away from the device. Keep it unobstructed by solder mask or conformal material unless the manufacturer instructions explicitly allow otherwise, and follow the recommended power and ground-plane layout.
What layout practices matter for an THS6182PWP line driver?
Place the THS6182PWP close to the line-coupling transformer and minimize the loop area of the differential output-current path. According to the Texas Instruments THS6182 datasheet design guidance, maintain a solid ground plane, provide low-inductance supply and ground connections, and use the prescribed exposed-pad via pattern. These steps reduce parasitic inductance, radiated emissions, and distortion.
Where can I request a quote and current lead time for THS6182PWP?
Use the Request a Quote form on this page to request current THS6182PWP availability, unit pricing, minimum order quantity, and lead time. The device is specified in a tube package, so confirm whether the requested quantity aligns with the manufacturer's standard tube quantity. A current distributor listing can confirm the exact suffix, but purchasing details should be confirmed through the quote process.

Справочные инженерные данные для THS6182PWP — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the THS6182PWP for a full-rate ADSL or power-line communication transmitter that requires a dedicated differential driver, a 5 V to 15 V supply, and adjustable line current. It is particularly appropriate when line-card density and dissipation are important because the device provides full-, mid-, low-, and shutdown modes plus an ADJ pin. The EL1503C and EL1508C may be considered when its manufacturer-stated pin compatibility aligns with the target circuit, but they should not be treated as confirmed THS6182PWP drop-ins without verifying the exact package, exposed pad, lead geometry, and electrical limits. The THS6182DWR is another member of the device family with a different ordering suffix, so its package drawing must be compared before considering it for an existing HTSSOP PCB. For a new design, prioritize the THS6182PWP when its listed bias modes, distortion, and noise characteristics satisfy the required line budget.

Сравнение с аналогами

Параметр Этот товар
Product Type ADSL and PLC differential line driver
Brand Texas Instruments
Package 20-pin HTSSOP with exposed pad
Number of Drivers 1 driver
Number of Receivers 0 receivers
Supply Voltage Range 5 V to 15 V
Total Harmonic Distortion -88 dBc at 100 kHz and 1 MHz
High-Bias Output Level +20 dBm with -76 dBc distortion
Bias Modes Full, mid, low, and shutdown modes with user-controlled ADJ
Input Current-Noise Density 3.2 nV/sqrt(Hz)

Ключевые отличия

  • Four selectable operating modes in one line driver (против EL1503C)
  • User-controlled bias-current adjustment (против EL1508C)
  • High-output low-distortion operating point (против EL1503C)

Заметки по проектированию

Connect the exposed pad to the ground plane and implement the manufacturer-recommended thermal-via arrangement. The HTSSOP package is intended to dissipate heat through its pad, so trace current through the pad and ground structure rather than relying only on narrow signal traces. Review the operating-mode current and line-output dissipation together because the full-bias setting uses 11 mA per channel and can create more heat than the lower-bias modes.

Place the THS6182PWP close to the line-coupling transformer and keep the differential output-current loop as small as practical. Use a continuous ground plane, short supply connections, and symmetrical routing where practical. Because the line driver supplies relatively high output current, parasitic inductance in power and ground paths can create voltage transients and additional distortion, so follow the recommended application layout in the Texas Instruments THS6182 datasheet.

Do not treat a family member with a different TI package suffix as a PCB drop-in replacement. The THS6182PWP uses a 20-pin HTSSOP with an exposed pad, and the EL1503C and EL1508C are described by Texas Instruments as pin compatible but still require package verification. Confirm body dimensions, lead geometry, pad area, exposed-pad connections, pin functions, bias control, drive current, and electrical limits before substitution.

Evaluate the transformer or coupling network together with the driver rather than judging the IC only by isolated distortion figures. The listed -88 dBc THD and +20 dBm high-bias capability are useful design targets, but real line performance also depends on impedance, loading, layout, and the selected bias mode. Use the ADJ control conservatively because increasing bias current improves potential launch level while also increasing dissipation.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The manufacturer product information identifies the THS6182PWP as an ADSL and PLC line driver but does not provide explicit compliance statements for this orderable part.

Данные проверены: 2026-11-20 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

THS6182PWP datasheet THS6182PWP specifications THS6182PWP pinout THS6182PWP datasheet pdf THS6182PWP equivalent THS6182PWP replacement THS6182PWP cross reference THS6182PWP vs EL1503C THS6182PWP footprint THS6182PWP application circuit THS6182PWP price THS6182PWP stock Texas Instruments THS6182PWP THS6182 20-HTSSOP line driver

Связанные компоненты & термины

Texas Instruments THS6182 THS6182PWP THS6182DWR EL1503C EL1508C ADSL line driver PLC line driver differential transmitter interface IC line driver communication semiconductor current-feedback differential line driver THS6182PWP 20-HTSSOP HTSSOP exposed pad surface mount package ADJ pin full-bias mode mid-bias mode low-bias mode shutdown mode total harmonic distortion input current-noise density central-office line card power-line communication
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ