THS6182PWP - Low-Power ADSL Line Driver | Texas Instruments
MPN: THS6182PWP ✓ AktifTHS6182PWP Genel Bakış
An ADSL line driver is an interface IC that converts a low-amplitude differential source signal into a high-current differential output suitable for transmission over telephone-line copper. This device belongs to the broader line-driver and transmitter hierarchy, within interface ICs and communication semiconductors. Its architecture is designed to increase line-card density by reducing quiescent current and power dissipation while maintaining the linearity required for full-rate ADSL systems.
The THS6182PWP supports full-bias, mid-bias, low-bias, and shutdown operating modes. The advertised channel-current settings are 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. An ADJ pin allows user-controlled bias current, and operation remains stable down to 1.8 mA per channel.
Signal-chain performance is centered on low distortion and low noise. The manufacturer lists total harmonic distortion of -88 dBc at 100 kHz and 1 MHz, while the high-bias configuration can drive +20 dBm on the line with -76 dBc distortion. The input current-noise density is listed as 3.2 nV per square hertz. These characteristics are relevant to receiver sensitivity because distortion and noise introduced at the line-driver stage can reduce the usable margin of the downstream receiver.
Typical applications include full-rate ADSL line cards, central-office ADSL equipment, power-line communication transmitters, and other copper-pair interfaces requiring differential current-drive capability. The adjustable bias architecture supports different line lengths, launch-power requirements, and system power budgets. A high-bias setting provides greater drive level when line loss is severe, while the lower-current modes reduce dissipation where adequate reach or signal level is not required.
PCB implementation requires attention to the exposed thermal pad, supply decoupling, high-current return paths, and controlled-impedance differential routing. Keep the driver close to the transformer or line-coupling network, minimize loop area in output-current paths, and use the manufacturer-recommended power and ground-plane construction to limit parasitic inductance. The exposed pad must be connected to the ground plane for both electrical return and heat dissipation.
This page consolidates the manufacturer specifications, package details, application guidance, and verified cross-reference information for engineers evaluating the THS6182PWP. It also identifies why a mechanically and electrically identical replacement should not be assumed from a similar line-driver description. Use the Texas Instruments THS6182 datasheet for the final pin assignments, recommended application circuit, exposed-pad layout, and electrical characteristics before releasing a PCB.
Drop-in alternatifler için THS6182PWP — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu ürüne yer değiştirme seçenekleri mevcut değil.
Alternatifleri Talep EdinTHS6182PWP Özellikler
| Product Type | Differential ADSL line driver |
| Number of Drivers | 1 driver |
| Number of Receivers | 0 receivers |
| Supply Voltage Range | 5 V to 15 V |
| Total Harmonic Distortion | -88 dBc at 100 kHz and 1 MHz |
| High-Bias Line Output | +20 dBm with -76 dBc distortion |
| Full-Bias Current | 11 mA per channel |
| Mid-Bias Current | 7.5 mA per channel |
| Low-Bias Current | 4 mA per channel |
| Kapatma Akımı | 0.25 mA per channel |
| Input Current-Noise Density | 3.2 nV/sqrt(Hz) |
| Minimum Stable Bias Current | 1.8 mA per channel |
| Bias Adjustment | User-controlled through ADJ pin |
| Paket | 20-pin HTSSOP with exposed pad, 4.40 mm body width |
| Packaging | Tube |
| Montaj Türü | Surface mount |
THS6182PWP 20-pin htssop with exposed pad, 4.40 mm body width Pin Yapısı Kılavuzu
THS6182PWP (20-pin htssop with exposed pad, 4.40 mm body width paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: THS6182PWP.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
THS6182PWP için uygundur 6 uygulamas: Full-Rate ADSL Line Cards, Central-Office ADSL Equipment, Power-Line Communication Transmitters, Digital Subscriber Line Access Multiplexer, Copper-Pair Communication Interfaces, Low-Power Line Interface Modules.
Full-Rate ADSL Line Cards
The THS6182PWP fits a full-rate ADSL transmitter because it combines a dedicated differential driver with selectable bias currents of 11 mA, 7.5 mA, or 4 mA per channel. According to the Texas Instruments THS6182 datasheet, its low-power design supports higher line-card density, while -88 dBc distortion at 100 kHz and 1 MHz helps preserve transmission linearity. Place the device near the line-coupling transformer, use the recommended exposed-pad ground pattern, and select the bias mode that provides adequate reach without unnecessary line-card dissipation.
Önerilen
Central-Office ADSL Equipment
Central-office line-card designs benefit from the THS6182PWP because low dissipation allows more channels to be placed in a limited rack space. Its four operating states provide a practical power budget: 11 mA per channel for full bias, 7.5 mA for mid bias, 4 mA for low bias, and 0.25 mA in shutdown. The Texas Instruments THS6182 datasheet also specifies operation down to 1.8 mA per channel, enabling designers to tune line current for reach, linearity, and thermal requirements.
Önerilen
Power-Line Communication Transmitters
The THS6182PWP is suitable for a power-line communication output stage because Texas Instruments describes it as an ADSL and PLC line driver. Its differential architecture drives a line-coupling network, while the ADJ pin provides user-controlled bias current for matching different cable lengths and network conditions. The listed +20 dBm high-bias capability and -76 dBc distortion offer a concrete starting point for link-budget and signal-integrity evaluation, with the tradeoff that higher bias current increases board power dissipation.
Önerilen
Digital Subscriber Line Access Multiplexer
A DSL access multiplexer can use the THS6182PWP at the line interface to create a high-current differential drive signal from the system transmitter. Its low quiescent dissipation is valuable when many subscriber ports share one line card, while selectable bias modes let designers optimize each port's launch power. The -88 dBc distortion specification supports high-linearity operation, but the output network, transformer, impedance, and routing must be evaluated as a complete signal path rather than in isolation.
Önerilen
Copper-Pair Communication Interfaces
The THS6182PWP can serve as the transmitter in equipment that sends differential current signals over copper pairs. Its 5 V to 15 V operating range supports conventional line-card supply architectures, and the four bias modes permit a single platform to cover short and long reaches. According to the Texas Instruments THS6182 datasheet, the 3.2 nV/sqrt(Hz) input current-noise density and low THD are particularly relevant when preserving receiver sensitivity and maintaining margin through the line interface.
Önerilen
Low-Power Line Interface Modules
The THS6182PWP supports compact line-interface modules where standby power and channel count are important constraints. Shutdown mode reduces the listed current to 0.25 mA per channel, while low-bias and mid-bias settings provide intermediate operating points. The Texas Instruments THS6182 datasheet indicates stable operation down to 1.8 mA per channel, giving hardware designers several control points for managing energy use while maintaining the differential line output required by ADSL or PLC equipment.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: THS6182PWP — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün |
|---|---|
| Product Type | ADSL and PLC differential line driver |
| Brand | Texas Instruments |
| Package | 20-pin HTSSOP with exposed pad |
| Number of Drivers | 1 driver |
| Number of Receivers | 0 receivers |
| Supply Voltage Range | 5 V to 15 V |
| Total Harmonic Distortion | -88 dBc at 100 kHz and 1 MHz |
| High-Bias Output Level | +20 dBm with -76 dBc distortion |
| Bias Modes | Full, mid, low, and shutdown modes with user-controlled ADJ |
| Input Current-Noise Density | 3.2 nV/sqrt(Hz) |
Ana Farklılayıcılar
- Four selectable operating modes in one line driver (karşılaştırma:EL1503C)
- User-controlled bias-current adjustment (karşılaştırma:EL1508C)
- High-output low-distortion operating point (karşılaştırma:EL1503C)
Tasarım Notları
Connect the exposed pad to the ground plane and implement the manufacturer-recommended thermal-via arrangement. The HTSSOP package is intended to dissipate heat through its pad, so trace current through the pad and ground structure rather than relying only on narrow signal traces. Review the operating-mode current and line-output dissipation together because the full-bias setting uses 11 mA per channel and can create more heat than the lower-bias modes.
Place the THS6182PWP close to the line-coupling transformer and keep the differential output-current loop as small as practical. Use a continuous ground plane, short supply connections, and symmetrical routing where practical. Because the line driver supplies relatively high output current, parasitic inductance in power and ground paths can create voltage transients and additional distortion, so follow the recommended application layout in the Texas Instruments THS6182 datasheet.
Do not treat a family member with a different TI package suffix as a PCB drop-in replacement. The THS6182PWP uses a 20-pin HTSSOP with an exposed pad, and the EL1503C and EL1508C are described by Texas Instruments as pin compatible but still require package verification. Confirm body dimensions, lead geometry, pad area, exposed-pad connections, pin functions, bias control, drive current, and electrical limits before substitution.
Evaluate the transformer or coupling network together with the driver rather than judging the IC only by isolated distortion figures. The listed -88 dBc THD and +20 dBm high-bias capability are useful design targets, but real line performance also depends on impedance, loading, layout, and the selected bias mode. Use the ADJ control conservatively because increasing bias current improves potential launch level while also increasing dissipation.
Uyumluluk Bilgisi
The manufacturer product information identifies the THS6182PWP as an ADSL and PLC line driver but does not provide explicit compliance statements for this orderable part.