TJ60S06M3L(T6L1,NQ - P-Ch -60V -60A 11.2mOhm DPAK+ MOSFET | Toshiba
Артикул: TJ60S06M3LT6L1.NQ ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $1.12 | $1,12 |
| 10 | $0.96 | $9,60 |
| 100 | $0.78 | $78,00 |
| 500 | $0.65 | $325,00 |
| 1.000 | $0.58 | $580,00 |
| 3.000 | $0.52 | $1.560,00 |
TJ60S06M3LT6L1.NQ Обзор
A P-channel MOSFET is a voltage-controlled field-effect transistor in which the conductive channel is formed by holes rather than electrons. Because P-channel devices turn on with a negative gate-source voltage, they simplify high-side switching in circuits where the load is tied to ground - no charge pump or bootstrap network is needed to drive the gate. P-channel MOSFETs are typically placed in the power-MOSFET hierarchy under 'P-channel -> MOSFET -> power MOSFET -> discrete semiconductor' and are widely used as reverse-polarity protection, high-side load switches, and synchronous-rectifier complements in DC-DC converters.
Key features of the TJ60S06M3L include the very low 11.2 milliohm Rds(on) at full gate drive, the -60 V drain rating that provides substantial avalanche headroom for 12 V / 24 V automotive buses, and an industry-standard DPAK+ footprint that allows direct PCB mounting with a thermal pad for low thermal resistance. The part is qualified for automotive motor drivers, DC-DC converters, and switching voltage regulators per Toshiba's product family positioning.
Technically, the device uses Toshiba's latest-generation U-MOS trench cell structure to achieve a per-cell figure-of-merit (FOM = Rds(on) x Qg) optimized for switching loss reduction. This makes it particularly suitable for hard-switched applications up to several hundred kHz where switching losses dominate conduction losses. The P-channel polarity allows direct logic-level driving from standard microcontrollers without additional gate-driver circuitry.
Typical applications include automotive ECU load switching, motor-driver H-bridge high-side switches, battery management system (BMS) reverse-polarity protection, synchronous-rectifier secondary-side switches in isolated DC-DC converters, and high-current load management in industrial 24 V systems. The DPAK+ package's exposed thermal pad allows direct PCB heatsinking.
When designing with this device, mind the gate-source voltage rating of +10 V / -20 V - the absolute maximum must not be exceeded even during transients. Use a gate-source resistor (typically 10 kohm) to prevent inadvertent turn-on from Miller-coupling during drain-voltage transients. Verify continuous drain current against your thermal envelope using the SOA curve from the manufacturer datasheet.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, providing a single reference for sourcing and second-sourcing the TJ60S06M3L(T6L1,NQ.
Аналоги без доработки для TJ60S06M3LT6L1.NQ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с TJ60S06M3LT6L1.NQ (тот же форм-фактор и посадочное место) — отличается по Input Capacitance (Ciss), Package, Technology.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
TJ60S06M3L
✅ Прямая замена✓ В наличии
$0.54 / шт.
Открыть даташит →TJ60S06M3L(T6L1,NQ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TJ60S04M3L
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
TJ60S06M3LT6L1.NQ Максимальные параметры и электрические характеристики
| Polarity | P-channel |
| Drain-Source Voltage (VDS) | -60 V |
| Gate-Source Voltage (VGS) | +10 V / -20 V |
| Continuous Drain Current (ID) at TC=25C | -60 A |
| Power Dissipation (PD) at TC=25C | 100 W |
| RDS(on) Max at VGS=-10V | 0.0112 ohm |
| Input Capacitance (Ciss) | 7760 pF |
| FET Type | MOSFET P-Channel, Metal Oxide |
| Тип монтажа | Surface Mount |
| Корпус | DPAK+ (TO-252) |
| Рабочая температура | -55C to +150C (Tj) |
| Technology | Toshiba U-MOS (silicon) |
| Уровень MSL | 1 (unlimited) |
| Статус RoHS | Compliant |
| Automotive Qualified | Yes (per Toshiba product positioning) |
Конфигурация выводов TJ60S06M3LT6L1.NQ
| Контакт 1 | Gate — Gate control input; drive with 0 to -10V relative to source for P-channel operation |
| Контакт 2 | Drain — Drain terminal; connected to load return path |
| Контакт 3 | Source — Source terminal; reference point for gate drive and thermal pad |
| Контакт 4 | Thermal Pad — Exposed thermal pad on underside; must be soldered to PCB copper for heatsinking |
Область безопасной работы (DC) for TJ60S06M3L
Типичное применение
TJ60S06M3LT6L1.NQ подходит для 7 применениеs: Automotive ECU Load Switching, Motor Driver H-Bridge High-Side Switch, Battery Management Reverse-Polarity Protection, Synchronous Rectifier in Isolated DC-DC Converters, Industrial 24V High-Side Load Management, USB-PD and Hot-Swap Protection Switch, Solar Charge Controller Blocking Diode Replacement.
Automotive ECU Load Switching
The TJ60S06M3L(T6L1,NQ suits 12V automotive ECU high-side load switching because of its -60V VDS rating providing ample avalanche margin against load-dump transients up to 35V, and its P-channel polarity which allows direct drive from a logic-level microcontroller GPIO without a charge pump. With RDS(on) of 11.2 milliohm at VGS=-10V, conduction loss at 20A load is only about 4.5W, manageable on a DPAK+ footprint with 1 square inch of copper. Compared to mechanical relays, this MOSFET offers silent switching, longer life, and finer PWM control for body-control modules and lighting drivers.
Рекомендуется
Motor Driver H-Bridge High-Side Switch
In brushed-DC motor H-bridges, the TJ60S06M3L(T6L1,NQ serves as the high-side switch on each leg, with its P-channel polarity allowing the bridge to be driven directly from logic-level signals without bootstrap capacitors. The -60V rating easily handles the back-EMF spikes of 24V motors, while the 60A continuous rating supports motor currents up to 30A per phase with proper heatsinking. The low RDS(on) of 11.2 milliohm minimizes thermal dissipation during PWM operation, critical for continuous-duty industrial motor control where the high-side FET conducts for the majority of each PWM cycle.
Рекомендуется
Battery Management Reverse-Polarity Protection
The TJ60S06M3L(T6L1,NQ is well suited for reverse-polarity protection (RPP) circuits in lithium-ion battery packs because its P-channel polarity naturally blocks current flow when the source is accidentally connected with reversed polarity. With -60V VDS and 60A current capability, the device can protect multi-cell battery packs up to 48V nominal without avalanche breakdown. The 11.2 milliohm RDS(on) keeps forward-path voltage drop below 50 mV at 5A charge current, preserving battery efficiency. Designers should add a TVS diode and adequate gate-bias network to ensure fast turn-off during fault events.
Рекомендуется
Synchronous Rectifier in Isolated DC-DC Converters
As a synchronous rectifier on the secondary side of an isolated DC-DC converter, the TJ60S06M3L(T6L1,NQ replaces Schottky diodes and improves efficiency by 3-5 percentage points in 12V-output converters. Its P-channel configuration simplifies the gate-drive timing relative to the primary-side switch, and its 60V VDS rating easily handles the reflected voltage stress on the secondary winding. The 7760 pF Ciss is moderate, allowing clean switching transitions at 100-300 kHz without excessive drive losses. Compared to a 60V Schottky diode at 20A load, this MOSFET reduces rectifier losses from about 15W to under 5W.
Рекомендуется
Industrial 24V High-Side Load Management
Industrial 24V systems benefit from the TJ60S06M3L(T6L1,NQ's -60V VDS rating which provides more than 2x safety margin over the 24V nominal bus, surviving inductive transients from solenoids, relays, and motor windings. The P-channel topology allows the load to be tied to ground, simplifying PCB layout and reducing ground-loop noise. With 60A continuous current, the device can switch entire subsystem power rails without paralleling. Designers should verify SOA at peak load conditions and provide adequate copper heatsinking on the DPAK+ thermal pad to keep junction temperature below 125C for long-term reliability.
Рекомендуется
USB-PD and Hot-Swap Protection Switch
The TJ60S06M3L(T6L1,NQ is suitable for USB-PD and hot-swap applications where a P-channel high-side switch must isolate the load during fault events. Its low RDS(on) of 11.2 milliohm minimizes voltage drop on the 5V/9V/15V/20V USB-PD output rails, while the -60V VDS rating handles capacitive inrush transients from downstream bulk capacitors. The 7760 pF Ciss combined with a 10kohm gate resistor provides sufficient Miller immunity to prevent shoot-through during fast dV/dt events. Designers should add current-limit and OVP functions upstream for full USB-PD compliance.
Рекомендуется
Solar Charge Controller Blocking Diode Replacement
In solar charge controllers, the TJ60S06M3L(T6L1,NQ replaces traditional Schottky blocking diodes to reduce forward-conduction losses and improve charge efficiency, particularly at high charge currents. Its P-channel polarity allows the MOSFET to be placed with source at the battery side and drain at the panel side, blocking reverse current flow at night with near-zero leakage. The 60V VDS rating handles 24V panel open-circuit voltage with margin, and the 100W power dissipation rating supports continuous charge currents up to 30A with proper PCB heatsinking on the DPAK+ footprint.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TJ60S06M3LT6L1.NQ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TJ60S06M3L | TJ60S06M3L(T6L1,NQ | TJ60S04M3L |
|---|---|---|---|---|
| Brand | Toshiba | Toshiba | Toshiba | Toshiba |
| Package | DPAK+ (TO-252) | DPAK+ (TO-252) - same | DPAK+ (TO-252) - same | DPAK+ (TO-252) - same |
| Polarity | P-channel | P-channel | P-channel | P-channel |
| Drain-Source Voltage (VDS) | -60 V | -60 V | -60 V | -40 V |
| Continuous Drain Current (ID) | -60 A | -60 A | -60 A | -60 A |
| Power Dissipation (PD) | 100 W | 100 W | 100 W | 100 W |
| Automotive Qualified | Yes (positioned) | Yes (positioned) | Yes (positioned) | Yes (positioned) |
Ключевые отличия
- U-MOS trench technology with ultra-low RDS(on) (против IRFR9024N (Infineon/IR, -55V / -11A planar))
- Modern surface-mount DPAK+ footprint (против TO-220 through-hole P-channel MOSFETs)
- P-channel topology eliminates charge pump (против Equivalent N-channel high-side switch designs)
Заметки по проектированию
Estimated: At ID = 30 A and RDS(on) = 0.0112 ohm, conduction loss is approximately 10 W. The DPAK+ package requires a thermal pad soldered to at least 1 square inch of 2 oz copper to keep junction-to-ambient thermal resistance (theta_JA) around 50 C/W. Without adequate copper, junction temperature can exceed 150 C at high duty cycle, causing thermal shutdown or reliability degradation. Designers should consult the manufacturer datasheet for the official thermal-resistance curves and use multiple thermal vias under the exposed pad.
The gate-drive trace should be kept short and routed away from the drain node to minimize Miller-capacitance coupling, which can cause inadvertent turn-on during high dV/dt switching events. Add a 10 kohm gate-source resistor to discharge the gate capacitance during power-down and prevent floating-gate turn-on. Use a separate gate-driver IC or dedicated gate-drive circuit if switching above 100 kHz to ensure clean gate transitions. Per Toshiba application guidance, keep the source-kelvin connection short for accurate current sensing.
Do not exceed the absolute maximum VGS rating of +10 V / -20 V; even brief transients above this range can punch through the oxide layer and permanently damage the device. Verify that the upstream gate-driver supply cannot overshoot during power-up. For P-channel operation in high-side switch topology, ensure the gate is pulled to the source voltage (off state) during power-down to prevent back-feeding the load. Always check the SOA curve at peak transient conditions - sustained operation at low VDS and high ID will exceed thermal limits.
Информация о соответствии
RoHS compliant per Toshiba product page. AEC-Q100 positioning for automotive motor drivers, DC-DC converters, and switching voltage regulators. Halogen-free status not stated by Toshiba reference set; confirm via latest product datasheet.
