TJA1051T/CM - 5Mbit/s High-Speed CAN Transceiver | NXP
Артикул: TJA1051T/CM ✓ АктивенTJA1051T/CM Обзор
A CAN transceiver is an interface IC within the Controller Area Network hierarchy. It converts logic-level TXD and RXD signals into the dominant and recessive voltage levels used by a wired CAN network, while also receiving bus information for the controller. The TJA1051T/CM therefore connects a digital CAN controller to the physical wiring of a multi-node vehicle, industrial machine, or embedded communications system without requiring the controller to handle the bus electrical layer directly.
The TJA1051 family is identified by NXP as a third-generation high-speed CAN transceiver with enhanced electromagnetic compatibility performance. Its 5 Mbit/s capability supports data transfer rates commonly required by automotive body, chassis, comfort, and controller-area-network systems. Differential bus signaling helps reject common-mode noise, while the dedicated TXD and RXD paths provide a clear separation between commands sent to the bus and data returned to the CAN controller.
The eight-pin SOIC package supports compact surface-mount assembly and exposes the CANH and CANL bus terminals, VCC, ground connections, TXD, and RXD. This arrangement allows the transceiver to be placed close to the bus connector and controller, reducing the distance over which sensitive signals and supply connections must travel. Exact operating voltage, ESD ratings, standby behavior, and temperature limits should be confirmed in the manufacturer datasheet before final circuit release.
Typical uses include automotive CAN gateways, body-control modules, electric-window and seating controllers, industrial automation equipment, sensors, and embedded diagnostic systems. In each application, the CAN controller handles frame construction, arbitration, acknowledgments, and higher-level protocols, while the TJA1051T/CM handles the physical-layer voltage conversion and bus-interface function. This division allows the host processor to work with ordinary digital logic while multiple nodes communicate over a shared two-wire network.
PCB design should prioritize short CANH and CANL routes, a compact common return path, and placement of the transceiver close to the bus connector. The bus-side network also needs termination, filtering, and protection suited to the vehicle or industrial environment. Validate the complete channel against EMC, ESD, ground-offset, and fault-recovery requirements rather than relying on general transceiver ratings alone.
This page combines the manufacturer's product description, exact package identification, verified sourcing references, and practical guidance for comparing, sourcing, and integrating the TJA1051T/CM. It also highlights the engineering boundaries that must be checked in the datasheet before using a similarly packaged CAN transceiver as a drop-in replacement.
Аналоги без доработки для TJA1051T/CM — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с TJA1051T/CM (тот же форм-фактор и посадочное место) — отличается по Package, Product Type, Protocol, Application Domain, Bus Interface.
TJA1051T/3/CM,118
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TJA1042T/1J
✅ Прямая заменаУточнить цену
Открыть даташит →TJA1057T/1Z
✅ Прямая заменаУточнить цену
Открыть даташит →TCAN1042VDRQ1
✅ Прямая замена✗ Нет в наличии
$0.33923 / шт.
Открыть даташит →TCAN1051VDRQ1
✅ Прямая заменаУточнить цену
Открыть даташит →MCP2562FD-E/SN
✅ Прямая заменаУточнить цену
Открыть даташит →TJA1051T/CM Характеристики
| Product Type | High-speed CAN transceiver |
| Maximum CAN Data Rate | 5 Mbit/s |
| Bus Interface | 2-wire differential CAN bus |
| Transmit Interface | Differential TXD to CANH/CANL |
| Receive Interface | Differential CANH/CANL to RXD |
| Logic Input | TXD |
| Logic Output | RXD |
| Корпус | 8-pin SOIC |
| Тип монтажа | Surface mount |
Конфигурация выводов TJA1051T/CM
| Контакт 1 | TXD — Transmit data input from the CAN controller |
| Контакт 2 | GND — Ground connection |
| Контакт 3 | NC — No connection |
| Контакт 4 | RXD — Receive data output to the CAN controller |
| Контакт 5 | VCC — Transceiver supply connection |
| Контакт 6 | CANL — CAN low bus terminal |
| Контакт 7 | CANH — CAN high bus terminal |
| Контакт 8 | GND — Ground connection |
Типичное применение
TJA1051T/CM подходит для 6 применениеs: Automotive Body Control Module, CAN Gateway and Network Interface, Industrial Automation Sensor Node, Vehicle Diagnostic Interface, Embedded CAN Communication Module, Robotics and Motor-Control Network.
Automotive Body Control Module
The TJA1051T/CM fits a body-control module that connects a CAN controller to vehicle wiring carrying climate, lighting, door, and seating commands. Its 5 Mbit/s capability supports high-speed communication, while the differential CANH/CANL interface connects the digital controller to the physical bus. Place the transceiver close to the bus connector and CAN controller, route CANH and CANL as a compact pair, and verify the exact ordering variant's automotive qualification and transient ratings against the vehicle requirements.
CAN Gateway and Network Interface
The TJA1051T/CM is suitable for a CAN gateway that bridges one or more CAN physical networks to a higher-level controller. The TXD path accepts commands from the protocol controller, and the RXD path returns decoded bus activity, while the transceiver handles the differential signaling on the two-wire network. The 5 Mbit/s data rate supports high-bandwidth gateway traffic. Validate node timing, termination, common-mode behavior, fault recovery, and ground-reference differences across connected modules before deployment.
Industrial Automation Sensor Node
The TJA1051T/CM can provide the physical CAN interface for an industrial sensor node that reports measurements to a programmable controller or supervisory system. Differential signaling supports communication over shared wiring where noise and grounding differences are present. Its 5 Mbit/s rate permits rapid periodic data exchange without loading the controller's communications task. Select bus protection and filtering for the installation environment, observe termination placement, and confirm the transceiver's exact EMC and ESD performance during system qualification.
Vehicle Diagnostic Interface
The TJA1051T/CM is appropriate for a vehicle diagnostic interface that connects a diagnostics processor to a CAN bus carrying powertrain, chassis, or body data. The high-speed interface complements controllers that already implement CAN frame handling and diagnostics services. The transceiver translates controller logic into differential bus signals and returns received bus states through RXD. For a production design, confirm the selected suffix's operating-temperature range, ESD rating, bus-fault recovery, and automotive qualification before approving the module.
Embedded CAN Communication Module
The TJA1051T/CM suits an embedded communication module built around a microcontroller or dedicated CAN controller. The controller handles arbitration, filtering, acknowledgments, and protocol frames, while the transceiver provides the electrical interface to the two-wire network. Its 5 Mbit/s capability can shorten response times in high-rate machine-control or data-acquisition systems. Keep TXD and RXD routing short, maintain a stable ground reference, and test the assembled node with the intended bus length and termination.
Robotics and Motor-Control Network
The TJA1051T/CM can be used in a robotics or motor-control network where distributed controllers exchange motion commands and status data over CAN. The 5 Mbit/s interface supports timely updates across multiple nodes, and differential bus signaling improves robustness in electrically noisy environments. Place the transceiver near the CAN connector, use symmetrical routing for CANH and CANL, and incorporate the termination and protection required by the motor environment. Verify fault behavior during power-up, bus-off recovery, and disconnected-cable conditions.
Справочные инженерные данные для TJA1051T/CM — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TJA1051T/3/CM,118 | TJA1042T/1J | TJA1057T/1Z | TCAN1042 | TCAN1051V | MCP2562FD |
|---|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | Texas Instruments | Texas Instruments | Microchip Technology |
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Bus Interface | 2-wire differential CAN | 2-wire differential CAN | 2-wire differential CAN | 2-wire differential CAN | 2-wire differential CAN | 2-wire differential CAN | 2-wire differential CAN |
| CAN FD Support | Classical CAN at 5 Mbit/s | Classical CAN at 5 Mbit/s | Classical CAN | Classical CAN | Classical CAN | Classical CAN | CAN FD |
| Pin-to-Pin Status | 8-pin SOIC reference design | 8-pin SOIC candidate; verify variant details | 8-pin SOIC candidate; verify electrical compatibility | 8-pin SOIC candidate; verify family differences | 8-pin SOIC pin-to-pin replacement candidate | 8-pin SOIC pin-to-pin replacement candidate | 8-pin SOIC pin-to-pin replacement candidate |
Ключевые отличия
- Higher nominal CAN rate than the 1 Mbit/s TJA1042T/1J candidate (против TJA1042T/1J)
- TJA1051-family EMC positioning (против TJA1057T/1Z)
- Classical CAN focus without relying on CAN FD behavior (против MCP2562FD)
- Established NXP high-speed transceiver family (против TCAN1042)
Заметки по проектированию
Place the TJA1051T/CM close to the CAN connector and route CANH and CANL as a short, closely coupled pair. Avoid discontinuities, long stubs, and sharp geometry that increase radiated emissions or susceptibility. Keep the bus-side return connection continuous, and observe the termination arrangement required at each end of the network. PCB-layer changes can affect differential impedance even when the nominal bus rate remains 5 Mbit/s.
Do not select a replacement from package shape alone. Confirm VCC, TXD and RXD logic thresholds, standby or enable behavior, loop delay, receiver propagation delay, bus fault recovery, ESD ratings, and the exact temperature grade. The TJA1051T/CM, TJA1042T/1J, TCAN1042, TCAN1051V, and MCP2562FD occupy the SOIC-8 class, but their electrical and protocol behaviors are not necessarily identical.
The TJA1051 family is positioned by NXP as a third-generation CAN transceiver with enhanced electromagnetic compatibility. Preserve that performance by using a continuous ground plane, short TXD and RXD paths, properly placed supply decoupling, and a symmetrical bus layout. Qualification testing should include conducted and radiated emissions, immunity, ground-offset conditions, and operation with realistic cable lengths because laboratory high-speed operation alone does not establish EMC compliance.
Информация о соответствии
The exact compliance and qualification status must be confirmed for the complete ordering code using NXP product documentation.