NXP Semiconductors

TJA1052IT/5 - Isolated 5 Mbps CAN Transceiver | NXP

Артикул: TJA1052IT/5 ✓ Активен
3 V to 5.25 V Vdss SOIC-16, 16 leads Package
MOQ: 1 |

TJA1052IT/5 Обзор

The NXP TJA1052IT/5 is a galvanically isolated, high-speed CAN transceiver operating at up to 5 Mbps in a 16-lead SOIC package. It provides a 1-transceiver, 1-receiver CAN interface with a 3 V to 5.25 V supply range, matching the logic levels commonly used by CAN controllers, microcontrollers, industrial automation equipment, electric vehicles, and hybrid electric vehicles.

A CAN transceiver is the physical-layer component that converts logic-level TXD and RXD signals into differential CAN bus signals, while receiving bus data and returning it as a logic-level RXD output. Galvanic isolation places a signal barrier between the CAN controller side and the two-wire CAN bus side. This helps protect the controller from ground-potential differences and electrical stress encountered in automotive and industrial installations.

The TJA1052IT/5 supports CAN data rates up to 5 Mbps and operates from a 3 V to 5.25 V supply. NXP identifies the device as an active high-speed CAN transceiver, and distributor listings describe it as a 1-transceiver, 1-receiver isolated half-CAN interface in a 16-pin SOIC package. Its operating temperature and automotive-qualification details should be confirmed against the specific orderable part number and the manufacturer datasheet before production release.

The part is especially relevant to electric and hybrid electric vehicle platforms, where a CAN controller must communicate with powertrain, battery-management, charger, and thermal-management subsystems. Industrial applications include motor drives, robotics, factory automation, and distributed control networks operating on long cable runs.

Design layouts should follow the manufacturer’s recommended application circuit, including the prescribed bus termination, common-mode choke, and split capacitor network where applicable. Keep CANH and CANL routing symmetric and controlled, provide solid ground-plane continuity, and avoid placing sensitive analog or high-speed digital traces parallel to the differential bus. Confirm the isolation barrier treatment, maximum bus length, node count, and stub geometry for the target network.

This page consolidates verified NXP product information, package and speed details, drop-in replacement candidates, comparison parameters, and practical CAN layout guidance to support component selection and PCB implementation.

Аналоги без доработки для TJA1052IT/5 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с TJA1052IT/5 (тот же форм-фактор и посадочное место) — отличается по Package, Product Type, Protocol, Supply Voltage Range, Transceiver Count.

Texas Instruments
Package: 16-pin wide-body SOIC (DW)
Product Type: Galvanically isolated CAN FD transceiver
Supply Voltage Range: 1.8 V to 5.5 V
NXP Semiconductors
Package: 16-pin SO (SOIC-16, 300 mil)
Protocol: CAN 2.0B / CAN FD
NXP Semiconductors
Package: 16-SOIC (SOT109-1) - 10.3 x 7.5 mm
Product Type: Isolated CAN Transceiver
Protocol: CAN, CAN FD

TJA1052IT/5Y

✅ Прямая замена
📦 SOIC-16
Same 5 Mbps isolated CAN specifications and SOIC-16 footprint; ordering suffix differs, with no stated electrical or timing difference

📋 Справочный аналог (нет в каталоге)

ISO1042DW

✅ Прямая замена
Texas Instruments
📦 SOIC-16
Galvanically isolated CAN FD transceiver · 5 Mbps · 1 Mbps · ISO 11898-2:2016 · ±70 V DC · ±30 V · 152 ns · 1.8 V to 5.5 V

Уточнить цену

Открыть даташит →

ISO1042-Q1

✅ Прямая замена
📦 SOIC-16
Automotive-oriented ISO1042 variant for the compatible 16-pin footprint; standby-net mapping and detailed electrical characteristics require board-level review

📋 Справочный аналог (нет в каталоге)

TJA1052IT/5 Характеристики

Product Type Galvanically isolated high-speed CAN transceiver
Maximum CAN Data Rate 5 Mbps
Supply Voltage Range 3 V to 5.25 V
Transceiver Count 1
Receiver Count 1
Bus Interface Half CANbus, two-wire differential
Isolation Galvanic isolation between controller and bus sides
Корпус SOIC-16, 16 leads
Package Body Width 300 mil
Тип монтажа Surface mount
Статус RoHS Compliant

Руководство по цоколевке TJA1052IT/5 в корпусе 300 mil

Цоколевка для TJA1052IT/5 (корпус 300 mil). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.

Схема цоколевки корпуса 300 mil для TJA1052IT/5

Нет подробных данных о распиновке для TJA1052IT/5.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

TJA1052IT/5 подходит для 6 применениеs: Electric Vehicle CAN Communications, Hybrid Electric Vehicle Powertrain Links, Industrial Motor Drive Networks, Robotics and Factory Automation, Battery Management Systems, Charging Infrastructure Communication.

🚗

Electric Vehicle CAN Communications

The TJA1052IT/5 fits an electric-vehicle CAN network where a vehicle controller must communicate with battery-management, inverter, charger, or thermal-control modules. Its galvanically isolated interface separates the controller domain from the physical two-wire bus, while the 5 Mbps capability supports high-speed classic CAN communication. The device operates from 3 V to 5.25 V and uses a 16-lead SOIC package. Designers should verify the exact automotive qualification, transient protection, common-mode choke, and split-capacitor recommendations in the manufacturer application circuit before releasing the board.

🚗

Hybrid Electric Vehicle Powertrain Links

The TJA1052IT/5 is appropriate for CAN links connecting hybrid powertrain controllers, engine controllers, transmission electronics, and supervisory vehicle computers. Its isolated transceiver architecture supports communication across domains that may develop different ground potentials, while 5 Mbps operation accommodates a broad range of classic CAN node speeds. The 3 V to 5.25 V supply range supports both 3 V and 5 V logic ecosystems. Confirm temperature grade, automotive qualification, standby behavior, and bus-fault ratings for the specific vehicle platform before production use.

🏭

Industrial Motor Drive Networks

The TJA1052IT/5 can connect a motor-drive controller to remote drives, sensors, and supervisory PLC infrastructure through an isolated two-wire CAN interface. Its 5 Mbps maximum rate provides margin for factory communication traffic, while the isolation barrier helps prevent bus disturbances and ground differences from propagating directly into the controller. The device supports a 3 V to 5.25 V supply and fits a compact SOIC-16 footprint. Layout work should follow the recommended split termination and common-mode choke network to limit emissions and improve robustness.

🏭

Robotics and Factory Automation

The TJA1052IT/5 is useful in robot controllers, machine vision systems, and distributed automation nodes that exchange commands and diagnostics over CAN. Its galvanic isolation helps protect a controller when motor drives, relays, and long external cables create noisy or shifted ground conditions. The transceiver supports up to 5 Mbps and uses a 3 V to 5.25 V supply, allowing it to pair with common embedded CAN controllers. Keep the differential bus route compact, provide a solid ground reference, and validate the complete topology against the bus-length and stub limitations of the selected CAN standard.

⚡

Battery Management Systems

The TJA1052IT/5 can serve as the isolated bus interface between a battery-management controller and other vehicle or industrial energy-storage subsystems. Isolation supports dependable communication when the high-voltage domain and low-voltage controller have substantial ground-potential separation. The device’s 5 Mbps capability supports high-speed CAN messaging used for cell data, contactor status, fault reporting, and thermal information. Because battery systems impose strict isolation and transient requirements, engineers must confirm the exact isolation rating, temperature grade, automotive qualification, and protection network from the manufacturer datasheet.

🔋

Charging Infrastructure Communication

The TJA1052IT/5 can connect charging-station controllers, communication modules, and service equipment operating on isolated CAN segments. Galvanic isolation helps maintain communication integrity when charger power stages, protective devices, and external utility interfaces are referenced to different grounds. Its 5 Mbps capability and 3 V to 5.25 V supply make it suitable for high-speed classic CAN links carrying status, authentication, and diagnostic data. Validate isolation lifetime, surge exposure, bus termination, and grounding for the installation class, and keep the CANH and CANL routes tightly coupled and away from high-current switching paths.

Сводка рекомендуемых товаров

ISO1042-Q1 Automotive-qualified pin-compatible replacement candidate Используется в: Electric Vehicle CAN Communications, Hybrid Electric Vehicle Powertrain Links, Battery Management Systems TJA1052IT/5Y Same-family orderable CAN transceiver Используется в: Electric Vehicle CAN Communications, Hybrid Electric Vehicle Powertrain Links, Industrial Motor Drive Networks, Battery Management Systems TJA1057GTK/3Z NXP Semiconductors Используется в: Industrial Motor Drive Networks, Robotics and Factory Automation, Charging Infrastructure Communication ISO1042DW Texas Instruments Используется в: Robotics and Factory Automation, Charging Infrastructure Communication
What is the TJA1052IT/5?
The TJA1052IT/5 is an NXP galvanically isolated, high-speed CAN transceiver for Controller Area Network communication. It provides one CAN transceiver and one receiver, supports data rates up to 5 Mbps, operates from 3 V to 5.25 V, and is offered in a 16-lead SOIC package. According to the NXP TJA1052IT product page, it creates an isolated interface between a CAN protocol controller and the physical two-wire CAN bus.
What is the maximum CAN data rate of TJA1052IT/5?
The TJA1052IT/5 supports a maximum CAN data rate of 5 Mbps. This rating is confirmed by the NXP product information and distributor listings that describe the device as a 5 Mbps high-speed CAN transceiver. Actual bus throughput also depends on controller timing, bus length, node count, termination, transceiver loop delay, and the CAN network’s operating mode, so the full system configuration must satisfy the applicable CAN timing requirements.
What is the supply voltage range of TJA1052IT/5?
The TJA1052IT/5 operates from 3 V to 5.25 V. This supply range allows the device to interface with 3 V and 5 V controller-side logic systems while providing an isolated CAN bus interface. Verified distributor specifications also identify 3 V as the minimum and 5.25 V as the maximum operating voltage. Check the manufacturer datasheet for the exact supply current, voltage tolerance, and decoupling requirements used in the final design.
Where can I download the TJA1052IT/5 datasheet?
The authoritative TJA1052IT/5 datasheet is available through the NXP product page at https://www.nxp.com/part/TJA1052IT. From that page, select the Data Sheet link for the exact orderable part number. The document should be used to confirm the pin configuration, isolation ratings, electrical characteristics, recommended application circuit, bus termination, standby behavior, and PCB layout requirements before the design is released.
Where is the TJA1052IT/5 pinout located?
The TJA1052IT/5 pinout is shown in the pin-description and application diagrams of the NXP manufacturer datasheet. The device uses a 16-lead SOIC package, and its pins are divided between the controller-side logic interface, isolated bus interface, power and ground connections, and isolation-related functions. Use the pin-description table in the datasheet when assigning PCB nets because specific functions such as standby must be verified against the exact orderable part number.
Is ISO1042DW a drop-in replacement for TJA1052IT/5?
The TI ISO1042 is identified in the manufacturer compatibility discussion as a replacement candidate for the TJA1052IT/5 in the 16-pin package. Its standby-related pin is implemented as a no-connect position, so the board’s existing standby net must be treated as an unused or no-connect pad rather than driven as before. Confirm the exact ISO1042 variant, isolation ratings, logic levels, timing, and bus-side pin mapping before approving the substitution.
What is the difference between TJA1052IT/5 and TJA1052IT/5Y?
The TJA1052IT/5 and TJA1052IT/5Y share the same datasheet and electrical specification, according to the NXP community discussion for the TJA1052IT family. The manufacturer identifies TJA1052IT/5 as the product type or product family and TJA1052IT/5Y as the orderable part number. For purchasing and production use, confirm that the orderable suffix matches the package, temperature grade, quality level, and delivery requirements of the design.
What is the best Texas Instruments equivalent for TJA1052IT/5?
The ISO1042DW is the leading Texas Instruments equivalent identified for the TJA1052IT/5 because it uses a compatible 16-pin arrangement and can serve as a drop-in replacement on the same footprint. The TJA1052 standby position corresponds to a no-connect position on the ISO1042, so one existing board net changes function. Review the TI E2E compatibility discussion and compare the two datasheets for isolation voltage, timing, standby behavior, and transient protection.
When should I choose TJA1052IT/5 instead of ISO1042DW?
Choose the TJA1052IT/5 when an NXP-sourced, galvanically isolated CAN transceiver with a standby function and a 5 Mbps maximum data rate matches the qualification and sourcing plan. Choose ISO1042DW when its electrical characteristics, isolation rating, and sourcing conditions are preferred, especially for an existing board where the standby pad can be left unconnected. Both support a 16-pin footprint, but the standby-net change must be reviewed before either part is substituted.
Can TJA1052IT/5 be used in electric vehicles?
Yes, the TJA1052IT/5 is specifically targeted by NXP at electric and hybrid electric vehicle applications. Its galvanically isolated CAN interface can connect a vehicle CAN controller to the physical two-wire network, while the isolation barrier helps manage ground-potential differences between electronic subsystems. Vehicle designs must still verify the exact temperature grade, automotive qualification status, network topology, transient protection, and safety requirements.
How do I choose between TJA1052IT/5 and TJA1052IT/5Y?
Treat TJA1052IT/5 and TJA1052IT/5Y as electrically and functionally equivalent members of the same TJA1052IT product family, but select the suffix that matches the specific orderable configuration required by procurement and manufacturing. The NXP community states that they share the same datasheet and specification. Before substitution, verify reel or tube packing, temperature grade, automotive grade, marking, and the manufacturer’s current lifecycle and ordering information.
What is the best drop-in replacement for TJA1052IT/5?
The ISO1042DW is a documented 16-pin replacement candidate for the TJA1052IT/5, and the ISO1042-Q1 compatibility discussion provides additional automotive-oriented guidance. Neither candidate should be treated as a blind substitution: the TJA1052 standby pin maps to a no-connect position on the ISO1042 family. Compare datasheet timing, logic thresholds, isolation ratings, bus protection, package dimensions, and lifecycle status before approving a drop-in redesign.
What can replace the TJA1052IT/5 on an existing PCB?
An ISO1042-family device in the compatible 16-pin package can replace the TJA1052IT/5 on an existing PCB, subject to an electrical and qualification review. The documented pin-compatibility difference is that the TJA1052 standby pin becomes a no-connect position on the ISO1042. Check the exact replacement variant, confirm that no external circuit depends on standby, and verify isolation and automotive requirements for the target vehicle or industrial system.
How should the TJA1052IT/5 CAN bus be laid out on a PCB?
Route CANH and CANL as a closely coupled differential pair with symmetric geometry, continuous ground reference, and no stubs on the bus nodes. Follow the NXP application circuit for the split capacitor, common-mode choke, and termination arrangement where recommended. Keep the bus pair away from antennas, switching regulators, crystals, and sensitive analog inputs, and route it directly to the connector to minimize radiated emissions and susceptibility.
Is the TJA1052IT/5 in stock, and what is its lead time?
Current stock and lead time should be confirmed through the Request a Quote form on this page because availability changes by region, quantity, and orderable suffix. The verified distributor results include in-market listings for the TJA1052IT/5Y family, while the TJA1052IT/5 and TJA1052IT/5Y share the same technical specification according to NXP. Provide your required quantity and packaging preference with the quote request to obtain current allocation and lead-time confirmation.
Where can I buy the TJA1052IT/5?
Use the Request a Quote form on this page to request the NXP TJA1052IT/5 with your required quantity, package, and orderable suffix. The form is the direct route for current unit pricing, stock confirmation, lead time, and order processing. Because TJA1052IT/5 is a family designation and TJA1052IT/5Y appears as an orderable part number in distributor records, specify the exact suffix when submitting the request to avoid receiving an unintended variant.

Справочные инженерные данные для TJA1052IT/5 — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the TJA1052IT/5 when the design requires an NXP-sourced, galvanically isolated CAN transceiver with a 5 Mbps maximum data rate, a 3 V to 5.25 V supply, and an active standby function. The TJA1052IT/5Y is the closest same-family choice when that exact orderable suffix is required for procurement, packaging, or traceability. Consider ISO1042DW for an existing 16-pin board when its electrical and sourcing advantages outweigh the standby-pin change. ISO1042-Q1 is relevant when an automotive-qualified replacement path is needed, but qualification, isolation, timing, and protection must be checked against the vehicle specification. For all three alternatives, confirm the exact package dimensions, isolation rating, temperature grade, bus protection, and lifecycle status before releasing production files.

Сравнение с аналогами

Параметр Этот товар TJA1052IT/5Y ISO1042DW ISO1042-Q1
Brand NXP Semiconductors NXP Semiconductors Texas Instruments Texas Instruments
Package SOIC-16 SOIC-16 - same SOIC-16 - same SOIC-16 - same
Device Type Galvanically isolated high-speed CAN transceiver Galvanically isolated high-speed CAN transceiver Isolated CAN transceiver Automotive isolated CAN transceiver
Standby Pin Mapping Standby function Standby function No-connect position replaces the TJA1052 standby pin Review compatibility discussion for the exact variant
Primary Target Application Electric and hybrid electric vehicles Electric and hybrid electric vehicles Industrial and automotive CAN communication Automotive CAN communication

Ключевые отличия

  • Native NXP ordering path for the isolated CAN family (против ISO1042DW)
  • Same documented electrical specification as the orderable TJA1052IT/5Y configuration (против TJA1052IT/5Y)
  • Targeted for electric and hybrid electric vehicle communication (против ISO1042-Q1)

Заметки по проектированию

Route CANH and CANL as a short, tightly coupled differential pair with symmetric geometry and a continuous ground reference beneath the pair. Keep the traces away from antennas, switching-regulator power nodes, clock signals, and sensitive analog inputs. Terminate each end of the bus with the impedance prescribed by the selected CAN network design, and avoid adding test-point stubs that create additional reflections.

Do not treat the ISO1042 standby-net mapping as a no-cost substitution. The documented compatibility path replaces the TJA1052 standby position with a no-connect position on the ISO1042, so any circuit that drives or senses that pad must be reviewed. Confirm logic thresholds, propagation timing, isolation rating, transient protection, temperature grade, and package dimensions before approving the change on an existing PCB.

Use the manufacturer-recommended split-capacitor and common-mode-choke arrangement where the application circuit calls for it. Place the filter components close to the transceiver bus pins and keep the return-current path within the isolation boundary defined by the device. Validate emissions and immunity at the system level because an optimized CAN trace alone does not establish compliance for the complete vehicle or industrial product.

Информация о соответствии

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

RoHS compliance is stated in the verified distributor product listing. Reach, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact orderable part number.

Похожие запросы

tja1052it 5y nxp tja1052it 5y datasheet tja1052it datasheet nxp tja1052it TJA1052IT/5 datasheet pdf TJA1052IT/5 pinout TJA1052IT/5 equivalent TJA1052IT/5 replacement TJA1052IT/5 vs ISO1042DW TJA1052IT/5 footprint TJA1052IT/5 price TJA1052IT/5 stock TJA1052IT SOIC-16 application circuit TJA1052IT isolated CAN transceiver

Связанные компоненты & термины

NXP Semiconductors TJA1052IT/5 TJA1052IT/5Y ISO1042DW ISO1042-Q1 CAN transceiver Controller Area Network high-speed CAN galvanic isolation CAN bus CANH CANL differential signaling SOIC-16 surface mount SMD common-mode choke split termination electric vehicle hybrid electric vehicle battery management system industrial automation 5 Mbps 3 V to 5.25 V RoHS
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ