TJA1052IT/5 - Isolated 5 Mbps CAN Transceiver | NXP
料号: TJA1052IT/5 ✓ 量产中TJA1052IT/5 概述
A CAN transceiver is the physical-layer component that converts logic-level TXD and RXD signals into differential CAN bus signals, while receiving bus data and returning it as a logic-level RXD output. Galvanic isolation places a signal barrier between the CAN controller side and the two-wire CAN bus side. This helps protect the controller from ground-potential differences and electrical stress encountered in automotive and industrial installations.
The TJA1052IT/5 supports CAN data rates up to 5 Mbps and operates from a 3 V to 5.25 V supply. NXP identifies the device as an active high-speed CAN transceiver, and distributor listings describe it as a 1-transceiver, 1-receiver isolated half-CAN interface in a 16-pin SOIC package. Its operating temperature and automotive-qualification details should be confirmed against the specific orderable part number and the manufacturer datasheet before production release.
The part is especially relevant to electric and hybrid electric vehicle platforms, where a CAN controller must communicate with powertrain, battery-management, charger, and thermal-management subsystems. Industrial applications include motor drives, robotics, factory automation, and distributed control networks operating on long cable runs.
Design layouts should follow the manufacturer’s recommended application circuit, including the prescribed bus termination, common-mode choke, and split capacitor network where applicable. Keep CANH and CANL routing symmetric and controlled, provide solid ground-plane continuity, and avoid placing sensitive analog or high-speed digital traces parallel to the differential bus. Confirm the isolation barrier treatment, maximum bus length, node count, and stub geometry for the target network.
This page consolidates verified NXP product information, package and speed details, drop-in replacement candidates, comparison parameters, and practical CAN layout guidance to support component selection and PCB implementation.
直接替换替代料: TJA1052IT/5 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TJA1052IT/5 (相同外形与封装尺寸) ——差异在于 Package, Product Type, Protocol, Supply Voltage Range, Transceiver Count.
TJA1052IT/5Y
✅ 直接替换📋 参考替代料(不在目录中)
ISO1042DW
✅ 直接替换联系询价
查看数据手册 →ISO1042-Q1
✅ 直接替换📋 参考替代料(不在目录中)
TJA1052IT/5 规格参数
| Product Type | Galvanically isolated high-speed CAN transceiver |
| Maximum CAN Data Rate | 5 Mbps |
| Supply Voltage Range | 3 V to 5.25 V |
| Transceiver Count | 1 |
| Receiver Count | 1 |
| Bus Interface | Half CANbus, two-wire differential |
| Isolation | Galvanic isolation between controller and bus sides |
| 封装 | SOIC-16, 16 leads |
| Package Body Width | 300 mil |
| 安装类型 | Surface mount |
| RoHS 状态 | Compliant |
TJA1052IT/5 300 mil 引脚配置指南
TJA1052IT/5(300 mil 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: TJA1052IT/5.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TJA1052IT/5 适用于 6 应用s: Electric Vehicle CAN Communications, Hybrid Electric Vehicle Powertrain Links, Industrial Motor Drive Networks, Robotics and Factory Automation, Battery Management Systems, Charging Infrastructure Communication.
Electric Vehicle CAN Communications
The TJA1052IT/5 fits an electric-vehicle CAN network where a vehicle controller must communicate with battery-management, inverter, charger, or thermal-control modules. Its galvanically isolated interface separates the controller domain from the physical two-wire bus, while the 5 Mbps capability supports high-speed classic CAN communication. The device operates from 3 V to 5.25 V and uses a 16-lead SOIC package. Designers should verify the exact automotive qualification, transient protection, common-mode choke, and split-capacitor recommendations in the manufacturer application circuit before releasing the board.
推荐
Hybrid Electric Vehicle Powertrain Links
The TJA1052IT/5 is appropriate for CAN links connecting hybrid powertrain controllers, engine controllers, transmission electronics, and supervisory vehicle computers. Its isolated transceiver architecture supports communication across domains that may develop different ground potentials, while 5 Mbps operation accommodates a broad range of classic CAN node speeds. The 3 V to 5.25 V supply range supports both 3 V and 5 V logic ecosystems. Confirm temperature grade, automotive qualification, standby behavior, and bus-fault ratings for the specific vehicle platform before production use.
推荐
Industrial Motor Drive Networks
The TJA1052IT/5 can connect a motor-drive controller to remote drives, sensors, and supervisory PLC infrastructure through an isolated two-wire CAN interface. Its 5 Mbps maximum rate provides margin for factory communication traffic, while the isolation barrier helps prevent bus disturbances and ground differences from propagating directly into the controller. The device supports a 3 V to 5.25 V supply and fits a compact SOIC-16 footprint. Layout work should follow the recommended split termination and common-mode choke network to limit emissions and improve robustness.
推荐
Robotics and Factory Automation
The TJA1052IT/5 is useful in robot controllers, machine vision systems, and distributed automation nodes that exchange commands and diagnostics over CAN. Its galvanic isolation helps protect a controller when motor drives, relays, and long external cables create noisy or shifted ground conditions. The transceiver supports up to 5 Mbps and uses a 3 V to 5.25 V supply, allowing it to pair with common embedded CAN controllers. Keep the differential bus route compact, provide a solid ground reference, and validate the complete topology against the bus-length and stub limitations of the selected CAN standard.
推荐
Battery Management Systems
The TJA1052IT/5 can serve as the isolated bus interface between a battery-management controller and other vehicle or industrial energy-storage subsystems. Isolation supports dependable communication when the high-voltage domain and low-voltage controller have substantial ground-potential separation. The device’s 5 Mbps capability supports high-speed CAN messaging used for cell data, contactor status, fault reporting, and thermal information. Because battery systems impose strict isolation and transient requirements, engineers must confirm the exact isolation rating, temperature grade, automotive qualification, and protection network from the manufacturer datasheet.
推荐
Charging Infrastructure Communication
The TJA1052IT/5 can connect charging-station controllers, communication modules, and service equipment operating on isolated CAN segments. Galvanic isolation helps maintain communication integrity when charger power stages, protective devices, and external utility interfaces are referenced to different grounds. Its 5 Mbps capability and 3 V to 5.25 V supply make it suitable for high-speed classic CAN links carrying status, authentication, and diagnostic data. Validate isolation lifetime, surge exposure, bus termination, and grounding for the installation class, and keep the CANH and CANL routes tightly coupled and away from high-current switching paths.
推荐
推荐产品汇总
工程参考数据: TJA1052IT/5 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TJA1052IT/5Y | ISO1042DW | ISO1042-Q1 |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | Texas Instruments | Texas Instruments |
| Package | SOIC-16 | SOIC-16 - same | SOIC-16 - same | SOIC-16 - same |
| Device Type | Galvanically isolated high-speed CAN transceiver | Galvanically isolated high-speed CAN transceiver | Isolated CAN transceiver | Automotive isolated CAN transceiver |
| Standby Pin Mapping | Standby function | Standby function | No-connect position replaces the TJA1052 standby pin | Review compatibility discussion for the exact variant |
| Primary Target Application | Electric and hybrid electric vehicles | Electric and hybrid electric vehicles | Industrial and automotive CAN communication | Automotive CAN communication |
关键差异点
- Native NXP ordering path for the isolated CAN family (对比 ISO1042DW)
- Same documented electrical specification as the orderable TJA1052IT/5Y configuration (对比 TJA1052IT/5Y)
- Targeted for electric and hybrid electric vehicle communication (对比 ISO1042-Q1)
设计说明
Route CANH and CANL as a short, tightly coupled differential pair with symmetric geometry and a continuous ground reference beneath the pair. Keep the traces away from antennas, switching-regulator power nodes, clock signals, and sensitive analog inputs. Terminate each end of the bus with the impedance prescribed by the selected CAN network design, and avoid adding test-point stubs that create additional reflections.
Do not treat the ISO1042 standby-net mapping as a no-cost substitution. The documented compatibility path replaces the TJA1052 standby position with a no-connect position on the ISO1042, so any circuit that drives or senses that pad must be reviewed. Confirm logic thresholds, propagation timing, isolation rating, transient protection, temperature grade, and package dimensions before approving the change on an existing PCB.
Use the manufacturer-recommended split-capacitor and common-mode-choke arrangement where the application circuit calls for it. Place the filter components close to the transceiver bus pins and keep the return-current path within the isolation boundary defined by the device. Validate emissions and immunity at the system level because an optimized CAN trace alone does not establish compliance for the complete vehicle or industrial product.
合规信息
RoHS compliance is stated in the verified distributor product listing. Reach, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact orderable part number.