NXP Semiconductors

TJA1053T/N1 - 5V Automotive CAN Transceiver | NXP

Артикул: TJA1053T/N1 ✓ Активен
4.75 V to 5.25 V Vdss 14-SO Package
MOQ: 1 |

TJA1053T/N1 Обзор

The NXP TJA1053T/N1 is a half CANbus transceiver for Controller Area Network communication, designed for a 4.75 V to 5.25 V supply range in a 14-pin SO package. Its interface pins tolerate voltages up to 36 V, supporting its use in automotive electrical environments when the surrounding circuitry provides the required protection and signal compatibility. The device combines a CAN transmitter and CAN receiver in one interface IC, providing the physical-layer connection between a CAN controller and the differential CAN bus.

A CAN transceiver is an interface IC within the broader Controller Area Network hierarchy. It converts logic-level data into a differential bus signal at the transmitter and reconstructs a logic-level signal from the bus at the receiver. This physical-layer function allows a microcontroller, automotive control unit, or industrial controller to exchange reliable data over a multi-node CAN network without implementing the electrical interface directly.

The TJA1053T/N1 operates from a nominal 5 V supply, with the documented operating range extending from 4.75 V to 5.25 V. Its I/O pins are tolerant to voltages as high as 36 V, an important consideration for 12 V automotive systems. The 14-SO package provides a compact surface-mount footprint suitable for automotive and industrial control equipment where PCB area is limited.

The principal design benefit is the combination of a 5 V transceiver interface with high-side I/O tolerance. Logic-side circuitry can operate from the regulated 5 V rail, while the CAN interface remains capable of withstanding the voltage excursions commonly encountered in vehicle electrical systems. The tolerance rating does not remove the need for correct transceiver placement, bus termination, decoupling, and protection strategy.

Typical uses include automotive body and comfort modules, engine controllers, instrument clusters, industrial automation equipment, CAN gateways, and embedded control systems. The device is particularly appropriate when the controller uses a 5 V supply and the CAN bus interface must tolerate the electrical environment associated with automotive wiring harnesses.

When laying out a board, place the transceiver close to the CAN connector and route TXD and RXD as short traces away from high-current switching nodes. Terminate the bus at both physical ends with the resistance specified by the CAN network design. Follow the pin-description table and application guidance in the manufacturer datasheet before assigning PCB tracks, supply bypass capacitors, or bus protection components.

This page consolidates the available manufacturer and distributor information with practical design guidance, package details, sourcing answers, and documented compatibility information. It helps engineers identify the correct CAN transceiver without confusing high-side I/O tolerance with immunity to arbitrary bus faults or eliminating the external protection required in automotive wiring.

Аналоги без доработки для TJA1053T/N1 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

TJA1054T

✅ Прямая замена
📦 14-SO
Documented by NXP as pin and downwards compatible with the TJA1053T; detailed data-rate and mode differences are .

📋 Справочный аналог (нет в каталоге)

TJA1054AT

✅ Прямая замена ⚠️ Характеристики не проверены
NXP Semiconductors
📦 14-SO
Fault-tolerant single-wire CAN transceiver · NXP Semiconductors · 125 kBd · Single-wire CAN · Protocol controller to physical bus-wire interface · ElectroStatic Discharge improved version of TJA1054 · Fault-tolerant CAN operation · SO14, 14 pins

Уточнить цену

Открыть даташит →

TJA1053T/N1 Характеристики

Product Type Half CANbus transceiver
Transceiver Configuration 1 transmit / 1 receive
Supply Voltage Range 4.75 V to 5.25 V
Nominal Supply Voltage 5 V
I/O Pin Voltage Tolerance Up to 36 V
Bus Type Controller Area Network (CAN)
Корпус 14-SO
Число выводов 14 pins
Тип монтажа Surface mount

Руководство по цоколевке TJA1053T/N1 в корпусе 14-so

Цоколевка для TJA1053T/N1 (корпус 14-so). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.

Схема цоколевки корпуса 14-so для TJA1053T/N1

Нет подробных данных о распиновке для TJA1053T/N1.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

TJA1053T/N1 подходит для 6 применениеs: Automotive Body Control Module, Engine Control Unit CAN Interface, Industrial CAN Gateway, Instrument Cluster CAN Interface, Embedded CAN Automation Controller, CAN Diagnostic Interface.

🚗

Automotive Body Control Module

The TJA1053T/N1 fits an automotive body-control module that connects a 5 V microcontroller to a 12 V CAN network. Its 4.75 V to 5.25 V operating range supports a regulated logic rail, while the documented 36 V tolerance of the I/O pins addresses the higher voltages encountered on vehicle wiring. Place the device between the controller and the bus connector, use the manufacturer's recommended supply bypass capacitors, and include suitable transient protection. The transceiver handles the CAN physical layer, while the controller remains responsible for frame handling, diagnostics, and fault management.

🚗

Engine Control Unit CAN Interface

The TJA1053T/N1 can provide the physical interface between an engine control unit and other powertrain nodes on a CAN bus. Its 5 V supply operation is appropriate for a regulated controller rail, and its I/O pins tolerate voltages up to 36 V for use in a 12 V vehicle environment. Keep the CAN differential route away from ignition and injector drive paths, place the transceiver near the bus connector, and verify termination in the network design. The controller must still implement CAN protocol handling, fault counters, bus-off recovery, and diagnostic strategies required by the vehicle system.

🏭

Industrial CAN Gateway

The TJA1053T/N1 is suitable for a compact industrial CAN gateway that translates between a 5 V controller and a CAN network. Its 4.75 V to 5.25 V supply requirement simplifies integration with conventional 5 V digital logic, while the 36 V I/O tolerance provides additional margin in electrically noisy installations. The design should include regulated supply routing, local decoupling, a protected bus connector, and correctly placed termination resistors. The device supports the CAN physical layer only, so protocol conversion, routing, diagnostics, and network management must be implemented by the surrounding controller or gateway electronics.

📺

Instrument Cluster CAN Interface

The TJA1053T/N1 can link an instrument cluster or display controller to a vehicle CAN network while operating from a 5 V rail. The transceiver's documented 36 V I/O tolerance is useful where the bus wiring experiences automotive-level transients, although it does not replace external surge protection. Route TXD and RXD away from display switching converters, provide local supply decoupling, and keep the CAN route away from display and backlight power paths. Firmware must handle absent nodes, bus-off events, and invalid frames through the CAN controller rather than through the physical-layer transceiver.

🏭

Embedded CAN Automation Controller

The TJA1053T/N1 is appropriate for a 5 V embedded automation controller that must join a CAN-based sensor or actuator network. It provides the physical-layer connection between the host controller and the bus while the protocol stack remains in firmware. The 14-SO package supports compact PCB layouts, and the 4.75 V to 5.25 V supply range aligns with a regulated 5 V rail. Apply the manufacturer's recommended decoupling, place termination only at designated network endpoints, and use a common reference ground with the bus interface. High-current actuator wiring should be routed separately from TXD, RXD, and the CAN differential pair.

🔧

CAN Diagnostic Interface

The TJA1053T/N1 can support a diagnostic adapter that links test equipment or service electronics to an automotive CAN network. Its 5 V supply operation supports conventional controller logic, and its I/O pins can tolerate voltages up to 36 V in the target vehicle environment. The adapter still needs an appropriate CAN controller, isolation or protection strategy as required by the installation, and software capable of handling diagnostic messages and network errors. Use the manufacturer application guidance to determine whether an additional bus protection component is required for the exposed connector and harness length.

What is the TJA1053T/N1?
The TJA1053T/N1 is a NXP Semiconductors half-duplex CANbus transceiver with one transmitter and one receiver. It operates from a 4.75 V to 5.25 V supply and is offered in a 14-SO surface-mount package. According to the manufacturer datasheet, its interface pins tolerate voltages up to 36 V, making it suitable for automotive CAN networks with 12 V electrical environments. It connects a CAN controller to the differential bus rather than processing the CAN protocol itself.
What is the supply voltage range of the TJA1053T/N1?
The TJA1053T/N1 operates from 4.75 V to 5.25 V, corresponding to a nominal 5 V supply. Its I/O pins are separately tolerant of voltages up to 36 V. According to the manufacturer datasheet, this distinction is important: the transceiver requires a regulated supply in the stated 5 V range, while the high-side interface pins can withstand the higher voltage excursions found in automotive wiring when the circuit is designed and protected correctly.
Where can I download the TJA1053T/N1 datasheet PDF?
The TJA1053T/N1 datasheet is available through the linked datasheet source, while NXP provides the authoritative device documentation and product resources. Use the manufacturer datasheet to verify pin assignments, electrical characteristics, application wiring, recommended decoupling, and bus protection before releasing a PCB. The 14-SO package drawing and pin-description table should also be checked against the mechanical drawing because SOIC-14 packages can be offered in different body widths and lead configurations.
Where can I find the TJA1053T/N1 pinout?
The TJA1053T/N1 pinout is defined in the pin-description table of the manufacturer datasheet. The verified package designation is 14-SO, corresponding to a 14-pin small-outline package for the package diagram used here. Before assigning PCB nets, verify the exact pin numbers for TXD, RXD, VCC, GND, and the CAN bus pins in the datasheet rather than relying on a generic SOIC-14 drawing, because package variants can differ in body width and pin geometry.
Is the TJA1053T/N1 suitable for 12 V automotive systems?
Yes, the TJA1053T/N1 is suitable for 12 V automotive CAN systems when its supply and bus-network requirements are implemented correctly. The device itself runs from a 4.75 V to 5.25 V supply, and its I/O pins are documented as tolerant to 36 V. According to the manufacturer datasheet, the transceiver therefore supports the voltage environment of a 12 V vehicle, but a regulated 5 V supply and suitable bus protection remain essential.
What can replace the TJA1053T/N1?
The TJA1054T is a documented replacement for the TJA1053T because NXP states that it is pin and downwards compatible while retaining the required functions. A replacement should still be checked for bus data rate, standby behavior, loopback support, supply range, transceiver polarity, package dimensions, and automotive qualification before production use. The documented compatibility establishes a practical replacement path, but it does not mean every device parameter is identical.
Is the TJA1053T/N1 the same as the TJA1054T?
The TJA1053T/N1 and TJA1054T are closely related CAN transceivers, and NXP documents the TJA1054T as pin and downwards compatible with the TJA1053T. They are therefore candidates for replacement in an existing design, but engineers should still compare the electrical limits, mode-control behavior, bus fault handling, data-rate support, and package dimensions. Compatibility means the stated functions are retained and pin compatibility is supported; it does not guarantee identical performance under every fault condition.
When should I choose the TJA1053T/N1 instead of the TJA1054T?
Choose the TJA1053T/N1 when the design specifically targets the original TJA1053T function set, a 5 V supply, and the established 14-SO footprint. Consider the TJA1054T when its additional or revised functions satisfy the system requirements and NXP's pin-compatibility statement is sufficient for the intended use. The choice should be made from a side-by-side review of standby, loopback, data-rate, fault-protection, and temperature requirements rather than from package appearance alone.
TJA1053T/N1 vs TJA1054T: which CAN transceiver is better?
The TJA1053T/N1 is the better direct choice when the existing circuit was designed around the TJA1053T and its documented behavior satisfies the product requirements. The TJA1054T is the stronger replacement candidate because NXP explicitly states pin and downwards compatibility with the TJA1053T. The decisive issues are the required standby or sleep behavior, bus data rate, loopback implementation, protection performance, and whether any changed function affects firmware or system-level diagnostics.
What is the best drop-in replacement for the TJA1053T/N1?
The TJA1054T is the best documented drop-in candidate identified for the TJA1053T because NXP states that it is pin and downwards compatible with that device and retains all required functions. Confirm the mechanical footprint and electrical operating limits in the manufacturer documentation before substitution. If the design relies on a feature whose behavior differs between the two transceivers, retain the TJA1053T/N1 or qualify another device after bench testing rather than relying only on the pin-compatibility statement.
Where can I buy the TJA1053T/N1 online?
Use the Request a Quote form on this page to request the TJA1053T/N1 and confirm current availability, order quantity, packaging, and lead time. Because the exact MPN may also be offered under manufacturer-specific order codes such as TJA1053T/N1,512 or TJA1053T/N1,518, include the required suffix and reel quantity when requesting a quote. This avoids accidentally ordering a different order code or delivery format.
What is the price of the TJA1053T/N1?
The current commercial price for the TJA1053T/N1 is presented through the Request a Quote form on this page. Submit the exact MPN, including any required reel suffix, and the requested quantity so the order can be matched to the correct packaging option. Prices and lead times can change with inventory and order volume, so the quote form provides the appropriate current purchasing response rather than a static price reference.
What is the lead time for the TJA1053T/N1?
The current lead time for the TJA1053T/N1 should be requested through the Request a Quote form on this page. Include the exact MPN, target quantity, reel suffix, and required delivery date when submitting the request. The manufacturer's product records and distributor listings may change in response to inventory movements, so obtain confirmation for the complete order configuration rather than relying on a generic availability statement.
Is the TJA1053T/N1 in stock?
Use the Request a Quote form on this page to confirm current stock for the exact TJA1053T/N1 order code. Specify whether you need TJA1053T/N1,512 or TJA1053T/N1,518, together with the required quantity. Inventory can differ between manufacturer stock and distributor inventory, and reel-packaging suffixes identify distinct orderable configurations. A quote response can confirm the currently available configuration and expected fulfillment timing.
What are the key specifications of the TJA1053T/N1?
The TJA1053T/N1 is a one-transmitter, one-receiver half CANbus transceiver in a 14-SO package. Its principal documented specifications are a 4.75 V to 5.25 V supply range and I/O tolerance up to 36 V. According to the manufacturer datasheet, these values support 5 V logic-side designs in automotive wiring environments. The device also has documented downward compatibility with the TJA1054T, which provides a defined route for replacement when its additional behavior remains acceptable.

Справочные инженерные данные для TJA1053T/N1 — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the TJA1053T/N1 when maintaining an existing TJA1053T-based design or when the product specifically requires its documented 4.75 V to 5.25 V supply range and 36 V I/O tolerance. It is well suited to 5 V automotive controllers and CAN interfaces connected to 12 V vehicle networks. Consider the TJA1054T when NXP's documented pin and downwards compatibility satisfies the system requirements, but compare standby, loopback, data-rate, fault-handling, and temperature limits before substitution. The TJA1054AT offers another same-brand family option, although its detailed compatibility and electrical differences require verification. Neither compatibility statement should be treated as permission to omit external bus protection, correct termination, supply decoupling, or qualification for the final vehicle or industrial environment.

Сравнение с аналогами

Параметр Этот товар TJA1054T TJA1054AT
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 14-SO 14-SO 14-SO
Transceiver Function 1/1 half CANbus transceiver CAN transceiver CAN transceiver

Ключевые отличия

  • Defined compatibility path for an existing TJA1053T design (против TJA1054T)
  • 5 V operation with automotive-level I/O tolerance (против TJA1054T)
  • Compact integrated half-transceiver footprint (против TJA1054AT)

Заметки по проектированию

Place the TJA1053T/N1 close to the CAN connector and route the CANH and CANL conductors as a tightly coupled differential pair. Keep TXD and RXD traces short and away from switching-power nodes, relays, and high-current motor wiring. Apply the datasheet's supply-decoupling recommendations directly to the VCC and ground pins, and confirm that the PCB's 14-SO land pattern matches the manufacturer's mechanical drawing before fabrication.

Do not interpret the documented 36 V I/O tolerance as permission to omit bus protection. It describes the transceiver's tolerated interface voltage, not immunity to every CAN bus fault or automotive transient. Determine whether the design requires an external protection component, surge arrester, common-mode choke, or galvanic isolation based on the harness environment and applicable vehicle or industrial requirements. Verify the selected protection scheme against the transceiver's absolute maximum ratings in the manufacturer datasheet.

Use the CAN network's specified termination only at the two physical endpoints; do not terminate every node. Keep the termination components close to the transceiver or connector as required by the board layout, and use a ground reference that follows the system's recommended single-point or multidrop strategy. A CAN bus is differential, but poor return-path continuity can still create common-mode noise, radiated emissions, and intermittent communication errors.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements were identified for the exact TJA1053T/N1 order code. Use the manufacturer product documentation and current declaration of conformity for production qualification.

Данные проверены: 2026-11-14 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

TJA1053T/N1 datasheet TJA1053T/N1 pinout TJA1053T/N1 datasheet pdf TJA1053T/N1 equivalent TJA1053T/N1 replacement TJA1053T/N1 cross reference TJA1053T/N1 vs TJA1054T TJA1053T/N1 footprint TJA1053T/N1 price TJA1053T/N1 stock NXP TJA1053T/N1 TJA1053T/N1 automotive CAN TJA1053T/N1 5V CAN transceiver TJA1053T/N1 14-SO pinout TJA1053T/N1 application circuit

Связанные компоненты & термины

NXP Semiconductors TJA1053T/N1 TJA1054T TJA1054AT Controller Area Network CAN transceiver CAN bus CANH CANL half-duplex transceiver physical-layer interface interface IC semiconductor 14-SO SOIC-14 surface-mount package automotive electronics industrial automation 5 V logic 36 V I/O tolerance CAN bus termination bus-off recovery transient protection embedded control system
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ