TJA1053T/N1 - 5V Automotive CAN Transceiver | NXP
MPN: TJA1053T/N1 ✓ Hoạt độngTJA1053T/N1 Tóm tắt
A CAN transceiver is an interface IC within the broader Controller Area Network hierarchy. It converts logic-level data into a differential bus signal at the transmitter and reconstructs a logic-level signal from the bus at the receiver. This physical-layer function allows a microcontroller, automotive control unit, or industrial controller to exchange reliable data over a multi-node CAN network without implementing the electrical interface directly.
The TJA1053T/N1 operates from a nominal 5 V supply, with the documented operating range extending from 4.75 V to 5.25 V. Its I/O pins are tolerant to voltages as high as 36 V, an important consideration for 12 V automotive systems. The 14-SO package provides a compact surface-mount footprint suitable for automotive and industrial control equipment where PCB area is limited.
The principal design benefit is the combination of a 5 V transceiver interface with high-side I/O tolerance. Logic-side circuitry can operate from the regulated 5 V rail, while the CAN interface remains capable of withstanding the voltage excursions commonly encountered in vehicle electrical systems. The tolerance rating does not remove the need for correct transceiver placement, bus termination, decoupling, and protection strategy.
Typical uses include automotive body and comfort modules, engine controllers, instrument clusters, industrial automation equipment, CAN gateways, and embedded control systems. The device is particularly appropriate when the controller uses a 5 V supply and the CAN bus interface must tolerate the electrical environment associated with automotive wiring harnesses.
When laying out a board, place the transceiver close to the CAN connector and route TXD and RXD as short traces away from high-current switching nodes. Terminate the bus at both physical ends with the resistance specified by the CAN network design. Follow the pin-description table and application guidance in the manufacturer datasheet before assigning PCB tracks, supply bypass capacitors, or bus protection components.
This page consolidates the available manufacturer and distributor information with practical design guidance, package details, sourcing answers, and documented compatibility information. It helps engineers identify the correct CAN transceiver without confusing high-side I/O tolerance with immunity to arbitrary bus faults or eliminating the external protection required in automotive wiring.
Bộ thay thế dễ dàng lắp đặt cho TJA1053T/N1 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
TJA1054T
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TJA1054AT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →TJA1053T/N1 Thông số kỹ thuật
| Product Type | Half CANbus transceiver |
| Transceiver Configuration | 1 transmit / 1 receive |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Nominal Supply Voltage | 5 V |
| I/O Pin Voltage Tolerance | Up to 36 V |
| Bus Type | Controller Area Network (CAN) |
| Hộp | 14-SO |
| Số chân | 14 pins |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân TJA1053T/N1 14-so
Cấu hình chân cho TJA1053T/N1 (14-so gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho TJA1053T/N1.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TJA1053T/N1 phù hợp cho 6 Áp dụngs: Automotive Body Control Module, Engine Control Unit CAN Interface, Industrial CAN Gateway, Instrument Cluster CAN Interface, Embedded CAN Automation Controller, CAN Diagnostic Interface.
Automotive Body Control Module
The TJA1053T/N1 fits an automotive body-control module that connects a 5 V microcontroller to a 12 V CAN network. Its 4.75 V to 5.25 V operating range supports a regulated logic rail, while the documented 36 V tolerance of the I/O pins addresses the higher voltages encountered on vehicle wiring. Place the device between the controller and the bus connector, use the manufacturer's recommended supply bypass capacitors, and include suitable transient protection. The transceiver handles the CAN physical layer, while the controller remains responsible for frame handling, diagnostics, and fault management.
Được đề xuất
Engine Control Unit CAN Interface
The TJA1053T/N1 can provide the physical interface between an engine control unit and other powertrain nodes on a CAN bus. Its 5 V supply operation is appropriate for a regulated controller rail, and its I/O pins tolerate voltages up to 36 V for use in a 12 V vehicle environment. Keep the CAN differential route away from ignition and injector drive paths, place the transceiver near the bus connector, and verify termination in the network design. The controller must still implement CAN protocol handling, fault counters, bus-off recovery, and diagnostic strategies required by the vehicle system.
Được đề xuất
Industrial CAN Gateway
The TJA1053T/N1 is suitable for a compact industrial CAN gateway that translates between a 5 V controller and a CAN network. Its 4.75 V to 5.25 V supply requirement simplifies integration with conventional 5 V digital logic, while the 36 V I/O tolerance provides additional margin in electrically noisy installations. The design should include regulated supply routing, local decoupling, a protected bus connector, and correctly placed termination resistors. The device supports the CAN physical layer only, so protocol conversion, routing, diagnostics, and network management must be implemented by the surrounding controller or gateway electronics.
Được đề xuất
Instrument Cluster CAN Interface
The TJA1053T/N1 can link an instrument cluster or display controller to a vehicle CAN network while operating from a 5 V rail. The transceiver's documented 36 V I/O tolerance is useful where the bus wiring experiences automotive-level transients, although it does not replace external surge protection. Route TXD and RXD away from display switching converters, provide local supply decoupling, and keep the CAN route away from display and backlight power paths. Firmware must handle absent nodes, bus-off events, and invalid frames through the CAN controller rather than through the physical-layer transceiver.
Được đề xuất
Embedded CAN Automation Controller
The TJA1053T/N1 is appropriate for a 5 V embedded automation controller that must join a CAN-based sensor or actuator network. It provides the physical-layer connection between the host controller and the bus while the protocol stack remains in firmware. The 14-SO package supports compact PCB layouts, and the 4.75 V to 5.25 V supply range aligns with a regulated 5 V rail. Apply the manufacturer's recommended decoupling, place termination only at designated network endpoints, and use a common reference ground with the bus interface. High-current actuator wiring should be routed separately from TXD, RXD, and the CAN differential pair.
Được đề xuất
CAN Diagnostic Interface
The TJA1053T/N1 can support a diagnostic adapter that links test equipment or service electronics to an automotive CAN network. Its 5 V supply operation supports conventional controller logic, and its I/O pins can tolerate voltages up to 36 V in the target vehicle environment. The adapter still needs an appropriate CAN controller, isolation or protection strategy as required by the installation, and software capable of handling diagnostic messages and network errors. Use the manufacturer application guidance to determine whether an additional bus protection component is required for the exposed connector and harness length.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TJA1053T/N1 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TJA1054T | TJA1054AT |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 14-SO | 14-SO | 14-SO |
| Transceiver Function | 1/1 half CANbus transceiver | CAN transceiver | CAN transceiver |
Bảo phân biệt quan trọng
- Defined compatibility path for an existing TJA1053T design (vsTJA1054T)
- 5 V operation with automotive-level I/O tolerance (vsTJA1054T)
- Compact integrated half-transceiver footprint (vsTJA1054AT)
Ghi chú thiết kế
Place the TJA1053T/N1 close to the CAN connector and route the CANH and CANL conductors as a tightly coupled differential pair. Keep TXD and RXD traces short and away from switching-power nodes, relays, and high-current motor wiring. Apply the datasheet's supply-decoupling recommendations directly to the VCC and ground pins, and confirm that the PCB's 14-SO land pattern matches the manufacturer's mechanical drawing before fabrication.
Do not interpret the documented 36 V I/O tolerance as permission to omit bus protection. It describes the transceiver's tolerated interface voltage, not immunity to every CAN bus fault or automotive transient. Determine whether the design requires an external protection component, surge arrester, common-mode choke, or galvanic isolation based on the harness environment and applicable vehicle or industrial requirements. Verify the selected protection scheme against the transceiver's absolute maximum ratings in the manufacturer datasheet.
Use the CAN network's specified termination only at the two physical endpoints; do not terminate every node. Keep the termination components close to the transceiver or connector as required by the board layout, and use a ground reference that follows the system's recommended single-point or multidrop strategy. A CAN bus is differential, but poor return-path continuity can still create common-mode noise, radiated emissions, and intermittent communication errors.
Thông tin tuân thủ
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements were identified for the exact TJA1053T/N1 order code. Use the manufacturer product documentation and current declaration of conformity for production qualification.