TLV2262IP Dual Rail-to-Rail Low-Power Op Amp | Texas Instruments
Артикул: TLV2262IP ✓ АктивенTLV2262IP Обзор
An operational amplifier, commonly called an op amp, is an analog integrated circuit that uses high-gain differential amplification to improve signals applied to its inputs. The TLV2262 belongs to the broader operational-amplifier hierarchy, which sits within analog and mixed-signal integrated circuits. Its rail-to-rail output architecture allows the output voltage to approach the supply rails more closely than a conventional fixed-headroom amplifier, improving usable output range in low-voltage systems.
The TLV2262IP combines low-power operation with rail-to-rail output performance. The manufacturer describes the device as a dual rail-to-rail low-voltage, low-power operational amplifier and identifies it as part of the Advanced LinCMOS rail-to-rail operational-amplifier family. Its dual-channel configuration provides two independent amplifier sections in one package, reducing component count when a board requires matched signal paths or multiple low-power analog channels.
The TLV2262 family is positioned between the micro-power TLV225x devices and the higher-ac-performance TLC227x devices. This positioning makes the TLV2262 useful when low supply current is important but greater bandwidth or dynamic capability is needed than a micropower amplifier provides. The manufacturer's TLV2262 family description specifically identifies the devices as suitable for low-power, battery-powered applications.
Typical uses include portable sensor conditioning, low-voltage audio amplification, instrumentation, industrial measurement interfaces, and embedded analog signal processing. The PDIP package is appropriate for through-hole boards, prototyping systems, and designs that favor easy inspection and hand assembly. Because the device is an analog amplifier, its input offset voltage, input bias current, noise, common-mode behavior, output capability, and stability with the selected feedback network determine the practical application performance.
When designing around the TLV2262IP, verify the exact pin assignment, supply limits, electrical characteristics, and recommended operating conditions in the manufacturer datasheet before assigning PCB connections. Pay particular attention to the choice of input and output biasing, the output-load condition, and the feedback topology. A stable feedback network and adequate decoupling are important when the amplifier drives capacitive loads or operates near a supply rail.
This product page combines the manufacturer’s device description, package and channel information, practical design guidance, sourcing-oriented commercial answers, and a conservative comparison of same-family alternatives. It is intended to help engineers establish whether the TLV2262IP fits a specific low-voltage analog design before moving to detailed datasheet review and PCB implementation.
Аналоги без доработки для TLV2262IP — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
TLV2262IP
✅ Прямая заменаУточнить цену
Открыть даташит →TLV2264IP
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
TLV2262IP Максимальные параметры и электрические характеристики
| Amplifier Type | Dual operational amplifier |
| Number of Channels | 2 channels |
| Technology | Advanced LinCMOS CMOS |
| Output Topology | Rail-to-rail output |
| Supply Voltage Range | ±4 V to 8 V |
| Корпус | 8-pin PDIP (P) |
| Тип монтажа | Through-hole |
Руководство по цоколевке TLV2262IP в корпусе 8-pin pdip (p)
Цоколевка для TLV2262IP (корпус 8-pin pdip (p)). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для TLV2262IP.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
TLV2262IP подходит для 6 применениеs: Portable Sensor Signal Conditioning, Battery-Powered Instrumentation, Low-Voltage Audio Preamplifier, Industrial Process Measurement, Low-Voltage Data Acquisition, Embedded Analog Control Interface.
Portable Sensor Signal Conditioning
The TLV2262IP suits portable sensing systems that need two low-voltage analog channels without adding a higher-power dual amplifier. Its dual-channel configuration supports paired conditioning paths such as a sensor signal and its reference, or a measurement input and an instrumentation stage. The manufacturer identifies the TLV2262 family as low-power and suitable for battery-powered equipment, while rail-to-rail output helps use more of the available signal range. Confirm the exact input common-mode range, offset, bias current, and supply current in the datasheet before fixing gain and biasing values.
Рекомендуется
Battery-Powered Instrumentation
TLV2262IP can condition low-level signals in handheld or field instrumentation where every milliamp affects operating time. Its two amplifier channels allow a system to handle more than one analog function in a single 8-pin PDIP package. The rail-to-rail output architecture is useful when the required output range is relatively close to the available supply voltage. Design the bias network and feedback resistors around the confirmed input offset, bias current, output swing, and supply-current limits, and include bypass capacitance close to the power pins.
Рекомендуется
Low-Voltage Audio Preamplifier
The TLV2262IP is appropriate for small-signal audio preamplification in portable or low-voltage analog equipment where two channels are useful for stereo or balanced signals. Rail-to-rail output can improve the usable swing from a limited supply, while the dual package reduces the number of amplifier components. The device is not presented as a high-performance audio amplifier, so the application should verify output-noise, distortion, slew-rate, and load-current specifications against the signal bandwidth. Feedback-component selection and output isolation from capacitive loads are especially important.
Рекомендуется
Industrial Process Measurement
TLV2262IP can support low-voltage process-measurement front ends that require two independent amplifier channels and through-hole assembly. Typical uses include scaling a transducer output and conditioning a temperature or level signal before conversion by an ADC. The low-voltage, low-power positioning supports compact control boards, while the PDIP package simplifies inspection and prototype rework. Confirm the amplifier’s common-mode range against the transducer output, and use its maximum output-current and capacitive-load limits to determine whether an isolation resistor or additional buffering stage is required.
Рекомендуется
Low-Voltage Data Acquisition
TLV2262IP fits two-channel data-acquisition boards where analog inputs must be scaled into a compact ADC range. One channel can amplify a primary sensor while the second handles a reference, monitor, or auxiliary input. Its rail-to-rail output improves signal utilization on low-amplitude supplies, and the dual architecture reduces board area compared with two separate single amplifiers. Choose resistor values that account for the device’s input-offset and bias-current effects, verify ADC input compatibility, and place local supply bypassing close to the amplifier to preserve measurement stability.
Рекомендуется
Embedded Analog Control Interface
The TLV2262IP can provide the analog interface between low-level control signals and an embedded ADC or comparator in a compact embedded system. Two channels allow simultaneous conditioning of a feedback signal and a command or threshold signal. Its low-voltage operation is appropriate for embedded systems powered from limited rails, while the through-hole PDIP package supports prototype and repair workflows. The design must maintain input signals inside the specified common-mode range and respect the output-voltage and load-current limits, especially when driving an ADC input, relay driver, or long PCB trace.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TLV2262IP — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TLV2262IP | TLV2264IP |
|---|---|---|---|
| Package | 8-pin PDIP (P) | 8-pin PDIP (P) | 8-pin PDIP (P) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Channels | 2 channels | 2 channels | 4 channels |
| Output Architecture | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
| Technology | Advanced LinCMOS CMOS | Advanced LinCMOS CMOS | Advanced LinCMOS CMOS |
| Power Class | Low-voltage, low-power | Low-voltage, low-power | Low-voltage, low-power |
| Family Positioning | Compromise between TLV225x micro-power performance and TLC227x AC performance | Dual-channel TLV226x family member | Quad-channel TLV226x family member |
| Mounting Type | Through-hole | Through-hole | Through-hole |
| Typical Application Focus | Portable, low-voltage dual-channel signal conditioning | Dual-channel portable signal conditioning | Quad-channel portable signal conditioning |
Ключевые отличия
- Two independent low-power amplifier channels in one package (против TLV2264IP)
- Rail-to-rail output for low-voltage signal range (против Conventional fixed-headroom operational amplifiers)
- Low-power family positioning between micropower and higher-AC-performance options (против TLV225x and TLC227x families)
Заметки по проектированию
Place the input, output, and feedback components close to their associated amplifier pins, and route the two channels to minimize shared-impedance coupling. The TLV2262IP uses a through-hole PDIP package, but short analog traces remain important even at low switching rates. Connect the power pins directly to a stable, locally bypassed supply and maintain the pin assignment shown in the manufacturer datasheet before finalizing the schematic.
The manufacturer positions the TLV2262 family as low-power for battery-powered systems, but the real supply budget depends on the selected supply voltage, channel activity, output load, and operating state. Review the per-amplifier quiescent current and load-current curves in the datasheet, then include both channels in the worst-case power calculation. Do not assume that the two channels can source their maximum output current simultaneously without checking the device limits.
Do not interpret rail-to-rail output as unrestricted common-mode input range or unlimited output swing. Verify where the input and output remain within their specified linear ranges at the actual supply voltage. Keep the feedback network stable under the expected capacitive load, and use an output isolation resistor if the load can introduce instability. Also check offset and bias-current errors before selecting very high resistor values for low-current sensor interfaces.
For low-level instrumentation, use a feedback topology that keeps both inputs within the usable common-mode region and calculate the maximum resistor value from the input bias-current specification. Place the matching feedback and gain-setting resistors close to the amplifier to reduce sensitivity to leakage and board contamination. Add a properly sized output isolation resistor when driving an ADC, cable, or other potentially capacitive load.
Информация о соответствии
Compliance details were not stated in the manufacturer or distributor listing excerpts reviewed for TLV2262IP. Confirm the current declarations and orderable-part qualification information with Texas Instruments.