TLV2450CP - 6V 220kHz Low-Power RRIO Op Amp | Texas Instruments
Артикул: TLV2450CP ✓ АктивенTLV2450CP Обзор
An operational amplifier, or op amp, is a high-gain analog building block used to amplify small voltage signals, buffer inputs, compare voltages, and drive analog-to-digital converter inputs. The TLV2450 belongs to the rail-to-rail input/output operational-amplifier family, where rail-to-rail input operation improves access to the supply-voltage range and rail-to-rail output operation increases output-voltage swing. Its low quiescent current reduces the supply demand of battery-powered and always-on circuits.
The main advantages are 220 kHz gain-bandwidth product, approximately 23 uA typical quiescent current, and operation from a single 6 V supply or a 2.7 V to 6 V supply range. The rail-to-rail input stage accepts signals near either supply rail, while the rail-to-rail output stage supports low-voltage signal conditioning with limited headroom. A shutdown function provides a way to reduce operating demand when the amplifier is not needed. These characteristics suit compact, low-power signal-processing systems without requiring a high-speed amplifier.
The TLV2450 is a general-purpose amplifier rather than a precision or high-current output device. Its 10 mA per channel output-current capability and 220 kHz bandwidth are appropriate for sensors, filters, and low-frequency analog stages, but not for demanding load driving, very wide-band instrumentation, or high-accuracy measurement rails. Designers should verify input and output common-mode limits, capacitive-load stability, shutdown behavior, and output-current requirements against the manufacturer datasheet before committing a design.
Typical uses include battery-powered sensor interfaces, portable measurement equipment, low-voltage audio and control circuits, analog signal conditioning, and embedded analog front ends. The 8-pin PDIP package favors through-hole prototyping, educational instruments, and applications where a socketed or easily inspectable amplifier is useful. The single-amplifier configuration also keeps board requirements simple when only one analog channel is required.
A primary design consideration is supply bypassing. Place a suitable local capacitor at the power pin and keep return-current paths short to reduce supply ripple and instability. Avoid driving long capacitive loads directly without checking the recommended output-capacitance limits. If shutdown is used, define its logic levels and state transitions carefully so the amplifier cannot oscillate between operating and shutdown modes.
This page combines the manufacturer's device characteristics, package information, practical application guidance, verified source links, and an explicit treatment of replacement constraints. The TLV2450CP is best selected when low quiescent current, rail-to-rail signal access, shutdown capability, and an 8-pin PDIP footprint are more important than precision, high-current output, or very high bandwidth.
Аналоги без доработки для TLV2450CP — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с TLV2450CP (тот же форм-фактор и посадочное место) — отличается по Amplifier Type, Input Offset Voltage, Package.
TLV2450IP
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →TLV2450AIP
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
TLV2450CP Максимальные параметры и электрические характеристики
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Supply Voltage Range | 2.7 V to 6 V |
| Maximum Supply Voltage | 6 V |
| Gain-Bandwidth Product | 220 kHz |
| Typical Quiescent Current | 23 uA |
| Input Offset Voltage | 500 uA |
| Output Current per Channel | 10 mA |
| Common-Mode Input | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Shutdown Function | Yes |
| Количество выводов | 8 pins |
| Корпус | PDIP-8 (P) |
| Body Width | 0.300 in (7.62 mm) |
| Диапазон рабочих температур | 0 C to 70 C |
| Тип монтажа | Through-hole |
Руководство по цоколевке TLV2450CP в корпусе pdip-8 (p)
Цоколевка для TLV2450CP (корпус pdip-8 (p)). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для TLV2450CP.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
TLV2450CP подходит для 6 применениеs: Battery-Powered Sensor Signal Conditioning, Portable Measurement Instrumentation, Low-Voltage Active Filtering, Portable Audio Preamplification, Low-Power Threshold Detection, Industrial Control Signal Buffering.
Battery-Powered Sensor Signal Conditioning
The TLV2450CP fits low-power sensor front ends because its approximately 23 uA typical quiescent current limits amplifier overhead in battery-powered equipment. Rail-to-rail input capability is valuable when the sensor output approaches a 3.3 V or 5 V rail, while rail-to-rail output provides useful headroom in low-voltage conditioning stages. The device can buffer, amplify, or filter a slowly varying sensor signal when the 220 kHz gain-bandwidth product exceeds the required closed-loop bandwidth. Check offset voltage, output-current demand, and noise requirements before using it for high-accuracy measurements.
Рекомендуется
Portable Measurement Instrumentation
Portable meters and compact data-acquisition systems benefit from the TLV2450CP's 220 kHz gain-bandwidth product and low 23 uA typical quiescent current. The amplifier can condition slow sensor, transducer, or divider signals without adding a high-current supply requirement to the instrument. Its rail-to-rail input stage helps preserve signal range in a low-voltage design, and the shutdown control can be useful when a measurement channel is inactive. For precision results, verify input offset, input bias current, output swing, and stability against the required measurement accuracy.
Рекомендуется
Low-Voltage Active Filtering
The TLV2450CP can implement first-order and modest higher-order active filters when the signal bandwidth is well below its 220 kHz gain-bandwidth product. Rail-to-rail input and output behavior is useful in filters powered from 2.7 V to 6 V, especially when filter nodes must approach the available signal range. The approximately 23 uA quiescent current keeps continuous filtering demand modest. Component tolerances and amplifier noise can set the practical filter accuracy, so simulate the complete response and verify stability with the intended source and load impedances.
Рекомендуется
Portable Audio Preamplification
The TLV2450CP is suitable for low-level preamplification in portable audio equipment when the source impedance and output load are compatible with a general-purpose amplifier. Its rail-to-rail input and output stages provide useful voltage range from a low-voltage supply, and the 220 kHz gain-bandwidth product covers many audible and ultrasonic low-bandwidth filtering requirements. The 10 mA per channel output-current rating makes it better suited to high-impedance audio paths than low-impedance headphone or speaker loads. Confirm input offset, noise, slew behavior, and capacitive-load stability before deployment.
Рекомендуется
Low-Power Threshold Detection
The TLV2450CP can compare a sensor or control voltage against a reference in battery-powered threshold-detection circuits. Rail-to-rail input operation allows the comparison signal to occupy more of the available 2.7 V to 6 V range, while rail-to-rail output improves drive capability for a downstream logic input. Its approximately 23 uA typical quiescent current supports low average system demand, and shutdown can disable the channel when monitoring is unnecessary. Confirm output logic levels, offset-induced switching uncertainty, input noise, and any feedback-network restrictions in the final circuit.
Рекомендуется
Industrial Control Signal Buffering
The TLV2450CP can buffer control, feedback, and sensor signals in low-voltage industrial subsystems where the operating range is 2.7 V to 6 V. Its rail-to-rail input and output behavior reduces signal-span loss near the supply rails, and the 220 kHz gain-bandwidth product is appropriate for many slow control loops. The single-amplifier PDIP package also simplifies through-hole assembly and field servicing. Do not use the 10 mA output-current capability for direct actuator drive; instead verify the load and add a suitable driver stage when more current or voltage swing is required.
Рекомендуется
Справочные инженерные данные для TLV2450CP — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Заметки по проектированию
Place the supply bypass capacitor close to the TLV2450CP power pin and connect it to a low-impedance ground return. Keep the input and feedback traces short, particularly when the amplifier drives a capacitive load. The 8-pin PDIP package allows through-hole accessibility, but lead spacing and routed return paths still require careful layout. Because this is a general-purpose low-power amplifier, verify output stability with the actual source impedance, load, and external capacitance rather than assuming every reactive load is acceptable.
Budget the approximately 23 uA typical quiescent current as part of the total amplifier supply demand, then add output-current consumption from the load. Estimated: at a 3.3 V supply and 23 uA quiescent current, the amplifier's own quiescent supply power is 75.9 uW. This estimate excludes load current, input bias effects, and shutdown-state consumption. Confirm the actual operating points against the datasheet before using it to size a battery or energy budget.
Do not treat rail-to-rail input or output as unlimited voltage range. The input common-mode limits, output-swing limits, and maximum 6 V supply rating remain authoritative. Likewise, the 10 mA per channel output-current capability is not a guarantee that every load can be driven at that current. Check the source and load impedances, required output amplitude, shutdown state, and permitted capacitive loading before releasing the PCB or production design.
Информация о соответствии
The manufacturer product information identifies the TLV2450CP as a commercial-temperature, 8-pin PDIP operational amplifier. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the available product information.