TLV2460ID - 6V, 6.4MHz RRIO Op Amp with Shutdown | Texas Instruments
Артикул: TLV2460ID ✓ АктивенTLV2460ID Обзор
An operational amplifier is an analog active device that uses high open-loop gain to amplify the difference between two input voltages. Rail-to-rail input capability allows the input common-mode voltage to approach the supply rails, while rail-to-rail output capability improves output swing in low-voltage systems. The TLV2460 belongs to the broader hierarchy of integrated circuits, analog amplifiers, voltage amplifiers, and general-purpose operational amplifiers.
The main differentiating feature of the TLV2460ID is its shutdown function, which allows the circuit to reduce operating current when the analog section is not required. Its 6.4 MHz gain-bandwidth product supports applications that need higher signal bandwidth than a basic micropower amplifier. The device is identified as a single amplifier with one shutdown control, making it suitable for designs requiring one analog channel rather than a dual or quad amplifier.
The TLV2460ID is used where a designer needs a compact, low-power amplifier with flexible input and output range. It can interface with sensors, buffer voltage references, perform active filtering, amplify audio or control signals, and condition inputs for higher-resolution converters. Its rail-to-rail behavior is particularly useful in systems powered from a single low-voltage rail, where conventional input and output ranges would leave insufficient headroom.
When using the TLV2460ID, connect bypass capacitors close to the supply pins and keep feedback-resistor networks compact to minimize parasitic capacitance and instability risk. The shutdown pin should be driven with a defined logic level whenever the amplifier state matters. Verify input and output signal limits against the supply voltage, especially during startup, shutdown transitions, and transients. The 8-pin SOIC package supports standard surface-mount assembly and hand-soldering workflows.
This page combines manufacturer and distributor references with drop-in replacement guidance, parameter comparisons, application notes, and practical PCB considerations for engineers evaluating the TLV2460ID in low-voltage analog designs.
Аналоги без доработки для TLV2460ID — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
TLV2460CDR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TLV2460AQDRG4
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TLV2460ID Максимальные параметры и электрические характеристики
| Number of Amplifiers | 1 amplifier |
| Напряжение питания | 6 V |
| Gain-Bandwidth Product | 6.4 MHz |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Shutdown Function | Yes |
| Amplifier Type | General-purpose operational amplifier |
| Диапазон рабочих температур | -40°C to +125°C |
| Package Type | SOIC (D) |
| Количество выводов | 8 pins |
| Maximum Power Dissipation | 710 mW |
| Minimum Dual Supply Voltage | ±1.35 V |
| Maximum Dual Supply Voltage | ±3 V |
| Тип монтажа | Surface mount |
Конфигурация выводов TLV2460ID
| Контакт 1 | OUT — Amplifier output |
| Контакт 2 | IN- — Inverting input |
| Контакт 3 | IN+ — Non-inverting input |
| Контакт 4 | V- — Negative supply connection |
| Контакт 5 | SHDN — Shutdown control input |
| Контакт 6 | V+ — Positive supply connection |
| Контакт 7 | NC — Not connected (per datasheet) |
| Контакт 8 | OUT — Amplifier output |
Типичное применение
TLV2460ID подходит для 6 применениеs: Low-Voltage Sensor Signal Conditioning, Active Filtering and Signal Conditioning, Portable Measurement and Test Equipment, Audio and Communication Interface Buffering, Battery-Powered IoT and Edge Sensing, Automotive and Industrial Analog Conditioning.
Low-Voltage Sensor Signal Conditioning
The TLV2460ID fits sensor front ends where the signal may occupy much of the available input range. Its rail-to-rail input characteristic allows the amplifier to accept signals near the supply rails, and the 6.4 MHz gain-bandwidth product provides headroom for moderate-bandwidth conditioning stages. Place the device close to the sensor or connector, use short input traces, and bypass the supply pins locally to reduce pickup. When the sensor is sampled intermittently, the shutdown function can reduce consumption between measurements.
Рекомендуется
Active Filtering and Signal Conditioning
Use the TLV2460ID for first- or second-order active filters in low-voltage instrumentation systems. Its rail-to-rail output capability helps preserve signal swing near the supply limits, while the 6.4 MHz gain-bandwidth product supports filter designs requiring reasonable closed-loop bandwidth. Keep the feedback resistors and capacitors close together to minimize parasitic capacitance, and verify phase margin with the amplifier’s datasheet models. Stable resistor values and adequate bypass capacitance are especially important at the higher end of the useful frequency range.
Рекомендуется
Portable Measurement and Test Equipment
The TLV2460ID is appropriate for handheld or bench measurement equipment powered from a low-voltage rail. Rail-to-rail input and output operation reduces headroom constraints, while the shutdown control allows the analog channel to be disabled when the instrument is idle. A 710 mW maximum power-dissipation rating provides a defined thermal limit for the package, although actual consumption is normally lower. Use the shutdown logic with care during power-up, and place local bypass capacitors at the supply pins.
Рекомендуется
Audio and Communication Interface Buffering
The TLV2460ID can buffer small-signal audio or communication nodes where rail-to-rail operation and a modest bandwidth are more important than very low distortion specifications. The 6.4 MHz gain-bandwidth product is sufficient for many low-frequency audio paths, but the application must remain within the amplifier’s output-current and capacitive-load limits. Keep feedback loops compact and isolate the output from long cable runs. The shutdown pin is useful in portable equipment where the channel is not continuously active.
Рекомендуется
Battery-Powered IoT and Edge Sensing
In battery-powered edge sensing, the TLV2460ID combines a single-amplifier configuration, rail-to-rail signal handling, and shutdown capability in a compact 8-pin SOIC package. The shutdown control can be asserted during idle periods to reduce system demand, while the amplifier provides a simple interface for resistive sensors, thermistors, or low-level analog nodes. The 6.4 MHz bandwidth is more than adequate for many sensor signals, but supply current and shutdown timing should be evaluated at the system level to maximize battery life.
Рекомендуется
Automotive and Industrial Analog Conditioning
The TLV2460AQDRG4 provides an automotive-qualified member of the same TLV2460 family for designs that require the SOIC-8 footprint and the family’s rail-to-rail amplifier characteristics. It is useful for low-level analog conditioning, actuator interfaces, and sensor buffering where temperature and qualification requirements are stricter. Verify the exact automotive qualification, temperature grade, and production requirements in the manufacturer documentation. For non-automotive industrial systems, TLV2460CDR is the closer same-family alternative identified.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TLV2460ID — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TLV2460CDR | TLV2460AQDRG4 |
|---|---|---|---|
| Package | SOIC-8 | SOIC-8 - same | SOIC-8 - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Amplifiers | 1 | 1 | 1 |
| Supply Voltage | 6 V | 6 V family rating | 6 V family rating |
| Gain-Bandwidth Product | 6.4 MHz | Equivalent primary performance rating | Equivalent primary performance rating |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Shutdown Function | Yes | Yes | Yes |
Ключевые отличия
- Same-family drop-in sourcing path (против TLV2460CDR)
- Automotive-grade family option (против TLV2460AQDRG4)
- Rail-to-rail signal range (против TLV2460CDR)
Заметки по проектированию
The TLV2460ID includes a shutdown control, so use it as an explicit power-management feature rather than leaving the control pin undefined. Assert shutdown during inactive periods in battery-powered systems, but account for startup and settling time before the first valid measurement. For a simple dissipation estimate, use P = VIN × IQUIESCENT + (VIN - VOUT) × ILOAD. The listed maximum power dissipation is 710 mW; actual operating dissipation depends on the supply, load, and output state.
Place the supply bypass capacitor as close as practical to the V+ and V- pins, and route input and feedback traces away from switching nodes and high-current paths. Keep the amplifier’s feedback network compact because parasitic capacitance can change the closed-loop response, particularly in gain configurations that approach the device’s 6.4 MHz gain-bandwidth product. Check the manufacturer land pattern for the SOIC-8 (D) package and confirm pin-1 orientation against the physical device marking.
Rail-to-rail input and output does not remove all design constraints. Verify that input signals, output swing, and shutdown-control levels remain valid during supply ramp-up and shutdown transitions. Do not drive the output into a heavy capacitive load unless the load and stability conditions are covered by the datasheet. For sensor interfaces, also account for source impedance, bias-current error, noise, and settling time rather than relying on bandwidth alone.
Информация о соответствии
The TLV2460 family is available from Texas Instruments, but the verified references for this record do not state the specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status of the TLV2460ID ordering option. Check the current manufacturer product and compliance documentation before release.