Texas Instruments

TLV2475CN - Quad 6V 2.8MHz Rail-to-Rail Op Amp | TI

Артикул: TLV2475CN ✓ Активен
6 V Vdss 600 µA Id 16-pin PDIP Package
MOQ: 1 |

TLV2475CN Обзор

Texas Instruments TLV2475CN is a quad CMOS operational amplifier designed for low-power, rail-to-rail signal conditioning on a 6 V supply. Each of its four channels provides a 2.8 MHz gain-bandwidth product, consumes approximately 600 µA per channel, and combines rail-to-rail input and output operation with 15 nV/√Hz input-voltage noise density. The device is supplied in a 16-pin PDIP package for through-hole PCB assembly.

An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while using negative feedback to set a stable closed-loop gain. The TLV2475 belongs to the CMOS operational amplifier, precision amplifier, and low-power amplifier hierarchy. Its rail-to-rail inputs and outputs let designers use most of the available supply voltage, making it suitable for portable equipment, sensor interfaces, audio paths, and industrial control systems.

The main electrical features include a 6 V maximum supply identified by Texas Instruments, 2.8 MHz gain-bandwidth product, 15 nV/√Hz input-voltage noise density, 78 dB common-mode rejection ratio, and 2.5 pA input bias current. Rail-to-rail input and output capability supports a broad range of common-mode and output-swing conditions. The operating temperature range extends from -40°C to +125°C, supporting industrial and extended-temperature equipment.

Four amplifiers are integrated into one package, reducing board area compared with four separate single or dual amplifier packages. The 2.8 MHz gain-bandwidth product is appropriate for low-frequency instrumentation, buffering, active filtering, and general signal conditioning rather than high-speed video or RF amplification. Its approximately 600 µA per channel operating current also makes it suitable for battery-operated systems where amplifier power consumption contributes materially to the system budget.

Typical applications include low-power sensor conditioning, portable measurement equipment, audio preamplification, current-loop receivers, active filters, and process-control modules. The four-channel organization also allows one device to serve several independent low-speed analog signals. Designers should still verify settling behavior, output swing, noise, and stability for the intended gain, load, and operating point.

For PCB layout, place input bias-return resistors and feedback components close to the relevant amplifier pins, and avoid routing sensitive input signals beside digital clock or switching-node traces. A solid ground plane and short feedback loops help preserve the low-noise benefit of the 15 nV/√Hz input stage. Decoupling capacitors should be positioned near the package supply pins according to the manufacturer layout guidance.

This product page combines manufacturer specifications, package details, engineering-oriented application guidance, and verified same-footprint alternatives. It also distinguishes the TLV2475CN from related low-power quad amplifiers and provides practical criteria for deciding when a shutdown-capable or different-family device is preferable.

Аналоги без доработки для TLV2475CN — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с TLV2475CN (тот же форм-фактор и посадочное место) — отличается по Gain-Bandwidth Product, Input Common-Mode Range, Output Swing, Package Type.

Texas Instruments
Gain-Bandwidth Product: 6.4 MHz
Input Common-Mode Range: Rail-to-rail input
Output Swing: Rail-to-rail output
Сравнить с TLV2475CN →

TLV2464CN

✅ Прямая замена ⚠️ Характеристики не проверены
Texas Instruments
📦 16-pin PDIP
4 channels · Low-power rail-to-rail input/output operational amplifier · 6 V · 6.4 MHz · Rail-to-rail input · Rail-to-rail output · 80 mA · 500 µA per channel

Уточнить цену

Открыть даташит →

TLV2468CN

✅ Прямая замена ⚠️ Характеристики не проверены
📦 16-pin PDIP
Uses the same 16-pin PDIP quad footprint but adds shutdown functionality, which changes one control connection and operating behavior

📋 Справочный аналог (нет в каталоге)

TLV2478CN

✅ Прямая замена ⚠️ Характеристики не проверены
📦 16-pin PDIP
Uses the same 16-pin PDIP footprint and 2.8 MHz bandwidth class but includes shutdown, requiring a pin-function and control-state review

📋 Справочный аналог (нет в каталоге)

TLV2475CN Максимальные параметры и электрические характеристики

Number of Amplifier Channels 4 channels
Maximum Supply Voltage 6 V
Gain-Bandwidth Product 2.8 MHz
Supply Current per Channel 600 µA
Input Voltage Noise Density 15 nV/√Hz
Common-Mode Rejection Ratio 78 dB
Input Bias Current 2.5 pA
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Minimum Operating Temperature -40°C
Maximum Operating Temperature +125°C
Package Type 16-pin PDIP
Способ монтажа Through hole
Количество выводов 16 pins
Process Technology CMOS

Руководство по цоколевке TLV2475CN в корпусе 16-pin pdip

Цоколевка для TLV2475CN (корпус 16-pin pdip). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.

Схема цоколевки корпуса 16-pin pdip для TLV2475CN

Нет подробных данных о распиновке для TLV2475CN.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

TLV2475CN подходит для 6 применениеs: Battery-Powered Sensor Conditioning, Portable Instrumentation, Audio Preamplification, Industrial Process-Control Loops, Active Filtering and Signal Conditioning, Data-Acquisition Analog Front End.

🧩

Battery-Powered Sensor Conditioning

The TLV2475CN is well suited to conditioning low-frequency outputs from resistive, temperature, and pressure sensors in portable equipment. Its approximately 600 µA supply current per channel limits the amplifier contribution to battery drain, while the 15 nV/√Hz input-voltage noise density helps preserve weak sensor signals. Rail-to-rail input and output operation is valuable when the usable signal range extends close to the 6 V supply limit. Four amplifiers can process several sensing channels without using four separate packages. The designer should use short input routes, local feedback networks, and an appropriate low-noise reference or sensor return path.

📱

Portable Instrumentation

The TLV2475CN supports portable instrumentation requiring multiple buffered analog channels at modest bandwidth. Its 2.8 MHz gain-bandwidth product is sufficient for many sensor, reference, and general measurement stages operating below hundreds of kilohertz, and the approximately 600 µA per-channel current is appropriate for instrument designs with limited power budgets. Rail-to-rail inputs and outputs improve signal utilization in compact systems. Four integrated amplifiers reduce board area, while the 78 dB common-mode rejection ratio helps reject interference coupled equally into differential inputs. Gain, output swing, and settling must be checked against the measurement bandwidth.

🎧

Audio Preamplification

The TLV2475CN can provide low-level audio preamplification in battery-operated or space-constrained products where the input bandwidth is modest. The 15 nV/√Hz input-voltage noise density is relevant when preserving quiet microphone or line-level signals, and rail-to-rail input operation accepts signals near the supply rails. Rail-to-rail output capability also helps maintain signal swing in low-voltage designs. The 2.8 MHz gain-bandwidth product is more than adequate for many audio control and auxiliary channels but should not be treated as a wideband audio power-amplifier solution. Feedback resistance, loading, distortion, and output-drive requirements remain the key checks.

🏭

Industrial Process-Control Loops

The TLV2475CN is applicable to low-frequency industrial process-control modules that require four precision amplifier channels around sensors, current loops, or actuator interfaces. Its -40°C to +125°C operating range covers extended industrial environments, and the 78 dB common-mode rejection ratio helps suppress common-mode noise on differential measurements. The approximately 600 µA per-channel supply current supports compact low-power control boards. Rail-to-rail inputs and outputs allow operation close to supply limits where signal range is restricted. Engineers should verify isolation margins, output drive into field-interface loads, and stability with the selected feedback network and sensor cable capacitance.

🔧

Active Filtering and Signal Conditioning

The TLV2475CN supports active filters, buffers, and general signal-conditioning blocks whose operating bandwidth is below the device's 2.8 MHz gain-bandwidth product. Four channels allow several filter sections or conditioning stages to be implemented in one through-hole package. Rail-to-rail output operation is useful for low-voltage filtering stages that need a wide output swing, while the 15 nV/√Hz noise density supports low-level inputs. The practical limit is not simply the quoted bandwidth: component tolerances, noise gain, capacitive loading, and the required closed-loop response determine whether the filter performs as intended.

🖥️

Data-Acquisition Analog Front End

The TLV2475CN can condition up to four low-frequency analog inputs before conversion in a compact data-acquisition system. Its 2.8 MHz gain-bandwidth product provides bandwidth for sensor amplification, level shifting, and anti-alias or active-filter stages below the converter's usable input bandwidth. Rail-to-rail input and output operation can simplify signal-range planning on low-voltage boards, while the 2.5 pA input bias current is favorable for high-impedance sources. The four-channel package reduces routing and component count. For each channel, verify settling time, noise contribution, common-mode range, ADC input range, and whether an external anti-alias filter is required.

What are the key specifications of TLV2475CN that engineers should know?
The TLV2475CN is a quad CMOS operational amplifier with a 6 V maximum supply, 2.8 MHz gain-bandwidth product, approximately 600 µA supply current per channel, 15 nV/√Hz input-voltage noise density, 78 dB CMRR, and 2.5 pA input bias current. Texas Instruments identifies the device as a 16-pin PDIP part with rail-to-rail input and output operation and an operating range of -40°C to +125°C. These characteristics place it between precision low-noise amplifiers and higher-bandwidth general-purpose devices.
Where can I download the TLV2475CN datasheet PDF?
The TLV2475CN datasheet and supporting documentation are available from the Texas Instruments TLV2475 product page at https://www.ti.com/product/TLV2475. The manufacturer product entry identifies TLV2475CN as a quad, 6 V, 2.8 MHz operational amplifier in a 16-pin PDIP package. Use the datasheet ordering table and pin-description diagram when assigning PCB tracks, confirming temperature-grade suffixes, and checking application-specific limits before releasing a design.
Where can I find the TLV2475CN pinout?
Use the TLV2475 family pin-description diagram in the Texas Instruments manufacturer datasheet to determine the TLV2475CN pin assignments and physical orientation. The exact TLV2475CN orderable configuration is a 16-pin PDIP package. Because the retrieved product result does not include a complete numbered pin table, the PCB footprint and every signal name should be checked directly against the manufacturer drawing before fabrication rather than inferred from an amplifier family generic diagram.
Is TLV2475CN rail-to-rail input and output?
Yes, the TLV2475CN provides rail-to-rail input and output operation according to the manufacturer product description for the TLV2475 family. This allows input common-mode voltages and output swings to extend toward the supply rails, which is valuable in low-voltage systems where signal range is limited. Actual usable range still depends on output load, gain, supply voltage, and channel-to-channel behavior, so designers should consult the datasheet curves for the intended operating point.
What is the gain-bandwidth product and noise density of TLV2475CN?
The TLV2475CN has a 2.8 MHz gain-bandwidth product and 15 nV/√Hz input-voltage noise density. According to the Texas Instruments product information, these figures characterize a low-power CMOS amplifier intended to balance supply current with AC performance. The bandwidth supports general-purpose low-frequency signal conditioning, while the noise specification is relevant to sensor, audio, and precision measurement front ends where minimizing input-referred noise improves usable signal quality.
What is the supply current of TLV2475CN?
The TLV2475 family consumes approximately 600 µA per channel, as stated in the TLV2475 technical description. A four-channel device therefore represents approximately 2.4 mA of channel supply current when all four channels are operating under the stated condition. Actual consumption depends on supply voltage, output swing, load, and operating mode, so this value should be treated as a design reference and checked against the manufacturer characteristic curves for the final load.
TLV2475CN vs TLV2464CN: which is better for low-power instrumentation?
Choose TLV2475CN when the design benefits from its 2.8 MHz gain-bandwidth product, 15 nV/√Hz noise density, and approximately 600 µA per-channel operating current. TLV2464CN is a closely related 16-pin quad amplifier and should be considered when its specific electrical limits and availability better match the design. Both families occupy the same PDIP footprint class, but engineers should compare rail-to-rail performance, output drive, settling, and stability for the intended gain before substitution.
What is the difference between TLV2475CN and TLV2475IN?
TLV2475CN and TLV2475IN represent different package options in the same TLV2475 family: CN uses a 16-pin PDIP configuration, while IN uses a surface-mount package. The core device function remains a quad, 6 V, 2.8 MHz operational amplifier. Because the physical package differs, TLV2475IN is not a board-level drop-in replacement for an existing TLV2475CN footprint. Choose it only when the PCB is redesigned for the surface-mount package.
When should I choose TLV2475CN over a single-channel amplifier?
Choose TLV2475CN when the board must process four independent low-frequency analog signals and can benefit from one shared package, common supply connection, and reduced component count. Four integrated channels can also simplify routing where several amplifiers share the same ground and supply region. A single-channel amplifier remains preferable when channel count is low, very small package area is dominant, or independent power control is required for each signal path.
Is TLV2475CN suitable for battery-powered sensor conditioning?
TLV2475CN is suitable for many battery-powered sensor-conditioning designs because its approximately 600 µA per-channel supply current is modest and its rail-to-rail input and output operation supports low-voltage systems. The 15 nV/√Hz input-voltage noise density can preserve weak sensor signals, while the 2.8 MHz gain-bandwidth product is generally more than sufficient for low-frequency measurement channels. Battery life still depends on sensor duty cycle, output activity, leakage, and the number of active channels.
What can replace TLV2475CN?
The closest documented drop-in choices are related Texas Instruments quad CMOS amplifiers in the same 16-pin PDIP footprint, including TLV2464CN, TLV2468CN, and TLV2478CN. Their shutdown and electrical characteristics differ, so replacement approval should include a complete pin-function, supply-current, noise, bandwidth, output-drive, and stability review. TLV2475IN cannot replace TLV2475CN without a PCB redesign because its package is different.
What is the best Texas Instruments equivalent for TLV2475CN?
TLV2464CN is the closest same-footprint Texas Instruments candidate for a four-channel, 16-pin PDIP replacement because it belongs to the related TLV246x low-power amplifier family. TLV2468CN and TLV2478CN are additional same-footprint family options, but their shutdown behavior differs from the TLV2475CN. No cross-brand equivalent can be confirmed from the retrieved cross-reference results, so qualified sourcing should not treat an unverified competitor as a drop-in replacement.
Where to buy TLV2475CN online?
Use the Request a Quote form on this TLV2475CN product page to request current unit availability, volume pricing, packaging details, and lead time for the exact 16-pin PDIP orderable MPN. The manufacturer product page and the listed distributor product result both identify TLV2475CN as the quad 6 V amplifier in a 16-pin PDIP package. Procurement should confirm the complete suffix, factory packaging, date code, and authorized-channel documentation before shipment.
What is the price of TLV2475CN?
Current TLV2475CN pricing is handled through the Request a Quote form on this page rather than embedded as a static offer. The form allows buyers to request quantity-based pricing for the exact 16-pin PDIP part, along with stock and lead-time confirmation. Price depends on order quantity, factory packaging, date code, market conditions, and component provenance, so it should be confirmed for the intended production quantity rather than inferred from family-level listings.
Is TLV2475CN in stock and what is its lead time?
Current stock and lead time for TLV2475CN should be requested through the Request a Quote form on this page using the exact MPN TLV2475CN. The manufacturer lists the device as an orderable 16-pin PDIP configuration, but stock can vary by package, date code, and order quantity. State your required quantity, acceptable date code, target date code range, and shipment destination when requesting the quotation so procurement receives an actionable availability response.
How should I design the PCB layout around TLV2475CN?
Place each amplifier's feedback components and optional input bias-return resistors close to its pins, and route the input node with minimal exposed length. Keep sensitive analog inputs away from switching regulators, high-current returns, and clock lines. The manufacturer's datasheet layout guidance should be followed for supply bypassing and grounding. Because the TLV2475CN contains four amplifiers in one package, maintain symmetry between channels and provide an uninterrupted ground return to reduce ground-induced noise and crosstalk.

Справочные инженерные данные для TLV2475CN — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Select TLV2475CN for low-power, low-frequency analog designs that require four rail-to-rail amplifier channels in a through-hole 16-pin PDIP package. Its 2.8 MHz gain-bandwidth product, 15 nV/√Hz noise density, approximately 600 µA per-channel supply current, and -40°C to +125°C range make it especially useful for sensor conditioning, portable instruments, active filtering, and industrial process-control modules. Consider TLV2464CN when its related-family electrical characteristics provide a better match and shutdown is unnecessary. Choose TLV2468CN or TLV2478CN only when an explicit shutdown function is useful and the control pin can be handled without disrupting the existing board. No cross-brand 16-pin PDIP replacement was confirmed, so do not treat a generic quad amplifier as a drop-in part without verifying pin functions, supply limits, output drive, noise, bandwidth, and stability.

Сравнение с аналогами

Параметр Этот товар TLV2464CN TLV2468CN TLV2478CN
Package 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Number of Channels 4 channels 4 channels 4 channels 4 channels
Gain-Bandwidth Product 2.8 MHz 2.8 MHz 2.8 MHz 2.8 MHz
Shutdown Function No shutdown indicated No shutdown indicated Shutdown capable Shutdown capable
Mounting Style Through hole Through hole Through hole Through hole

Ключевые отличия

  • Four amplifiers in one 16-pin PDIP package (против TLV2464CN)
  • Rail-to-rail input and output operation (против TLV2468CN)
  • Specified low-noise input stage (против TLV2478CN)

Заметки по проектированию

Route each TLV2475CN input and feedback connection directly to its associated device pins, and place optional input bias-return resistors close to the amplifier rather than at the source connector. Because one package contains four independent amplifiers, keep sensitive channels physically separated from high-current or switching signals on the board. A continuous ground plane beneath the package and short ground returns will reduce channel-to-channel coupling and common-mode pickup.

Check settling and phase margin at the intended closed-loop gain rather than assuming that the 2.8 MHz gain-bandwidth product alone guarantees stability. Sensor cables and ADC input capacitance can add poles, so use the manufacturer stability guidance when driving capacitive loads. If additional filtering is required, place the feedback network and output isolation resistor close to the relevant pins and evaluate overshoot with the worst-case load and supply combination.

Budget approximately 600 µA per active channel for the TLV2475 family under the manufacturer-described operating condition, or roughly 2.4 mA when all four channels are active. Treat this as a reference calculation rather than a worst-case limit. Include supply-decoupling capacitance close to the package pins, account for startup and output-swing current, and verify the regulator can support the measured transient demand without moving the supply rail enough to distort the conditioned signal.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The retrieved manufacturer and distributor entries do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these attributes for the exact orderable MPN and current manufacturer documentation before qualification.

Данные проверены: 2026-11-19 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

TLV2475CN datasheet TLV2475CN specifications TLV2475CN pinout TLV2475CN application circuit Texas Instruments TLV2475CN TLV2475CN 2.8MHz op amp TLV2475CN 16-pin PDIP TLV2475CN vs TLV2464CN TLV2475CN drop-in replacement TLV2475CN equivalent amplifier TLV2475CN price TLV2475CN stock TLV2475CN lead time TLV2475CN rail-to-rail amplifier

Связанные компоненты & термины

Texas Instruments TLV2475CN TLV2475 TLV2464CN TLV2468CN TLV2478CN operational amplifier CMOS operational amplifier precision amplifier low-power amplifier quad amplifier rail-to-rail input rail-to-rail output gain-bandwidth product input-voltage noise density common-mode rejection ratio CMRR input bias current 16-pin PDIP DIP package through-hole mounting sensor conditioning portable instrumentation industrial process control active filtering
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ