TLV2475CN - Quad 6V 2.8MHz Rail-to-Rail Op Amp | TI
料号: TLV2475CN ✓ 量产中TLV2475CN 概述
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while using negative feedback to set a stable closed-loop gain. The TLV2475 belongs to the CMOS operational amplifier, precision amplifier, and low-power amplifier hierarchy. Its rail-to-rail inputs and outputs let designers use most of the available supply voltage, making it suitable for portable equipment, sensor interfaces, audio paths, and industrial control systems.
The main electrical features include a 6 V maximum supply identified by Texas Instruments, 2.8 MHz gain-bandwidth product, 15 nV/√Hz input-voltage noise density, 78 dB common-mode rejection ratio, and 2.5 pA input bias current. Rail-to-rail input and output capability supports a broad range of common-mode and output-swing conditions. The operating temperature range extends from -40°C to +125°C, supporting industrial and extended-temperature equipment.
Four amplifiers are integrated into one package, reducing board area compared with four separate single or dual amplifier packages. The 2.8 MHz gain-bandwidth product is appropriate for low-frequency instrumentation, buffering, active filtering, and general signal conditioning rather than high-speed video or RF amplification. Its approximately 600 µA per channel operating current also makes it suitable for battery-operated systems where amplifier power consumption contributes materially to the system budget.
Typical applications include low-power sensor conditioning, portable measurement equipment, audio preamplification, current-loop receivers, active filters, and process-control modules. The four-channel organization also allows one device to serve several independent low-speed analog signals. Designers should still verify settling behavior, output swing, noise, and stability for the intended gain, load, and operating point.
For PCB layout, place input bias-return resistors and feedback components close to the relevant amplifier pins, and avoid routing sensitive input signals beside digital clock or switching-node traces. A solid ground plane and short feedback loops help preserve the low-noise benefit of the 15 nV/√Hz input stage. Decoupling capacitors should be positioned near the package supply pins according to the manufacturer layout guidance.
This product page combines manufacturer specifications, package details, engineering-oriented application guidance, and verified same-footprint alternatives. It also distinguishes the TLV2475CN from related low-power quad amplifiers and provides practical criteria for deciding when a shutdown-capable or different-family device is preferable.
直接替换替代料: TLV2475CN ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TLV2475CN (相同外形与封装尺寸) ——差异在于 Gain-Bandwidth Product, Input Common-Mode Range, Output Swing, Package Type.
TLV2464CN
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →TLV2468CN
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TLV2478CN
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TLV2475CN 最大额定值与电气特性
| Number of Amplifier Channels | 4 channels |
| Maximum Supply Voltage | 6 V |
| Gain-Bandwidth Product | 2.8 MHz |
| Supply Current per Channel | 600 µA |
| Input Voltage Noise Density | 15 nV/√Hz |
| Common-Mode Rejection Ratio | 78 dB |
| Input Bias Current | 2.5 pA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Minimum Operating Temperature | -40°C |
| Maximum Operating Temperature | +125°C |
| Package Type | 16-pin PDIP |
| 安装方式 | Through hole |
| 引脚数 | 16 pins |
| Process Technology | CMOS |
TLV2475CN 16-pin pdip 引脚配置指南
TLV2475CN(16-pin pdip 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TLV2475CN.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TLV2475CN 适用于 6 应用s: Battery-Powered Sensor Conditioning, Portable Instrumentation, Audio Preamplification, Industrial Process-Control Loops, Active Filtering and Signal Conditioning, Data-Acquisition Analog Front End.
Battery-Powered Sensor Conditioning
The TLV2475CN is well suited to conditioning low-frequency outputs from resistive, temperature, and pressure sensors in portable equipment. Its approximately 600 µA supply current per channel limits the amplifier contribution to battery drain, while the 15 nV/√Hz input-voltage noise density helps preserve weak sensor signals. Rail-to-rail input and output operation is valuable when the usable signal range extends close to the 6 V supply limit. Four amplifiers can process several sensing channels without using four separate packages. The designer should use short input routes, local feedback networks, and an appropriate low-noise reference or sensor return path.
推荐
Portable Instrumentation
The TLV2475CN supports portable instrumentation requiring multiple buffered analog channels at modest bandwidth. Its 2.8 MHz gain-bandwidth product is sufficient for many sensor, reference, and general measurement stages operating below hundreds of kilohertz, and the approximately 600 µA per-channel current is appropriate for instrument designs with limited power budgets. Rail-to-rail inputs and outputs improve signal utilization in compact systems. Four integrated amplifiers reduce board area, while the 78 dB common-mode rejection ratio helps reject interference coupled equally into differential inputs. Gain, output swing, and settling must be checked against the measurement bandwidth.
推荐
Audio Preamplification
The TLV2475CN can provide low-level audio preamplification in battery-operated or space-constrained products where the input bandwidth is modest. The 15 nV/√Hz input-voltage noise density is relevant when preserving quiet microphone or line-level signals, and rail-to-rail input operation accepts signals near the supply rails. Rail-to-rail output capability also helps maintain signal swing in low-voltage designs. The 2.8 MHz gain-bandwidth product is more than adequate for many audio control and auxiliary channels but should not be treated as a wideband audio power-amplifier solution. Feedback resistance, loading, distortion, and output-drive requirements remain the key checks.
推荐
Industrial Process-Control Loops
The TLV2475CN is applicable to low-frequency industrial process-control modules that require four precision amplifier channels around sensors, current loops, or actuator interfaces. Its -40°C to +125°C operating range covers extended industrial environments, and the 78 dB common-mode rejection ratio helps suppress common-mode noise on differential measurements. The approximately 600 µA per-channel supply current supports compact low-power control boards. Rail-to-rail inputs and outputs allow operation close to supply limits where signal range is restricted. Engineers should verify isolation margins, output drive into field-interface loads, and stability with the selected feedback network and sensor cable capacitance.
推荐
Active Filtering and Signal Conditioning
The TLV2475CN supports active filters, buffers, and general signal-conditioning blocks whose operating bandwidth is below the device's 2.8 MHz gain-bandwidth product. Four channels allow several filter sections or conditioning stages to be implemented in one through-hole package. Rail-to-rail output operation is useful for low-voltage filtering stages that need a wide output swing, while the 15 nV/√Hz noise density supports low-level inputs. The practical limit is not simply the quoted bandwidth: component tolerances, noise gain, capacitive loading, and the required closed-loop response determine whether the filter performs as intended.
推荐
Data-Acquisition Analog Front End
The TLV2475CN can condition up to four low-frequency analog inputs before conversion in a compact data-acquisition system. Its 2.8 MHz gain-bandwidth product provides bandwidth for sensor amplification, level shifting, and anti-alias or active-filter stages below the converter's usable input bandwidth. Rail-to-rail input and output operation can simplify signal-range planning on low-voltage boards, while the 2.5 pA input bias current is favorable for high-impedance sources. The four-channel package reduces routing and component count. For each channel, verify settling time, noise contribution, common-mode range, ADC input range, and whether an external anti-alias filter is required.
推荐
推荐产品汇总
工程参考数据: TLV2475CN ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TLV2464CN | TLV2468CN | TLV2478CN |
|---|---|---|---|---|
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Gain-Bandwidth Product | 2.8 MHz | 2.8 MHz | 2.8 MHz | 2.8 MHz |
| Shutdown Function | No shutdown indicated | No shutdown indicated | Shutdown capable | Shutdown capable |
| Mounting Style | Through hole | Through hole | Through hole | Through hole |
关键差异点
- Four amplifiers in one 16-pin PDIP package (对比 TLV2464CN)
- Rail-to-rail input and output operation (对比 TLV2468CN)
- Specified low-noise input stage (对比 TLV2478CN)
设计说明
Route each TLV2475CN input and feedback connection directly to its associated device pins, and place optional input bias-return resistors close to the amplifier rather than at the source connector. Because one package contains four independent amplifiers, keep sensitive channels physically separated from high-current or switching signals on the board. A continuous ground plane beneath the package and short ground returns will reduce channel-to-channel coupling and common-mode pickup.
Check settling and phase margin at the intended closed-loop gain rather than assuming that the 2.8 MHz gain-bandwidth product alone guarantees stability. Sensor cables and ADC input capacitance can add poles, so use the manufacturer stability guidance when driving capacitive loads. If additional filtering is required, place the feedback network and output isolation resistor close to the relevant pins and evaluate overshoot with the worst-case load and supply combination.
Budget approximately 600 µA per active channel for the TLV2475 family under the manufacturer-described operating condition, or roughly 2.4 mA when all four channels are active. Treat this as a reference calculation rather than a worst-case limit. Include supply-decoupling capacitance close to the package pins, account for startup and output-swing current, and verify the regulator can support the measured transient demand without moving the supply rail enough to distort the conditioned signal.
合规信息
The retrieved manufacturer and distributor entries do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these attributes for the exact orderable MPN and current manufacturer documentation before qualification.