TLV2781ID - 3.6V, 8MHz RRIO Op Amp | Texas Instruments
Артикул: TLV2781ID ✓ АктивенTLV2781ID Обзор
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The TLV2781 belongs to the voltage-feedback operational-amplifier hierarchy, where rail-to-rail input and output capability allows the amplifier to operate close to the supply rails. This is particularly useful in low-voltage systems because conventional input and output stages may not cover the full available signal range.
The TLV2781ID's principal characteristics include one amplifier circuit per package, an 8 MHz gain-bandwidth product, and a 3.6 V maximum specified supply voltage. Its rail-to-rail input capability is useful when sensor outputs or low-level signals move close to ground. Rail-to-rail output improves usable output swing in compact 1.8 V-class systems, although the exact input offset, output-current, noise, and stability limits should be taken from the manufacturer datasheet for the intended operating conditions.
Texas Instruments describes the TLV2781 family as high-speed, 1.8 V-capable rail-to-rail input/output operational amplifiers. The 8 MHz bandwidth makes the device suitable for signal paths that require more response than a general-purpose low-speed amplifier but do not require the bandwidth of a high-speed video amplifier. Its extended-temperature rating supports industrial equipment, instrumentation, portable measurement systems, and control loops operating across broad ambient conditions.
Typical uses include low-voltage sensor conditioning, current-loop receivers, ADC input drivers, transducers, battery-powered instruments, and general analog signal-processing blocks. The 8-pin SOIC package is also practical for prototypes and through-hole industrial boards where a small surface-mount footprint is desirable. Designers should preserve output-current margin, account for capacitive loading, and select external compensation or isolation when driving unusual loads.
The principal design consideration is power-rail compatibility. The device supports low-voltage operation, but its 3.6 V rating is a maximum, not a recommendation to operate at that voltage without checking every datasheet limit. Decoupling, grounding, input common-mode range, output swing, and stability requirements must all be evaluated for the actual circuit.
This page consolidates the manufacturer specifications, ordering information, package details, pricing evidence, and engineering guidance for the TLV2781ID. It also identifies where replacement decisions require additional qualification, particularly for shutdown behavior, supply tolerance, bandwidth, rail-to-rail performance, and exact pin compatibility.
Аналоги без доработки для TLV2781ID — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Для этого товара нет аналогов без доработки.
Запросить аналогиTLV2781ID Максимальные параметры и электрические характеристики
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Maximum Supply Voltage | 3.6 V |
| Minimum Operating Supply Voltage | 1.8 V |
| Gain-Bandwidth Product | 8 MHz |
| Input Type | Rail-to-rail |
| Тип выхода | Rail-to-rail |
| Диапазон рабочих температур | -40°C to 125°C |
| Корпус | 8-pin SOIC (D) |
| Тип монтажа | Surface mount |
| Manufacturer | Texas Instruments |
| Product Family | TLV278x |
| Rail-to-Rail Input and Output | Yes |
Руководство по цоколевке TLV2781ID в корпусе 8-pin soic (d)
Цоколевка для TLV2781ID (корпус 8-pin soic (d)). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для TLV2781ID.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
TLV2781ID подходит для 6 применениеs: Low-Voltage Sensor Conditioning, Battery-Powered Instrumentation, Industrial ADC Input Driver, Current-Loop Receiver, Transducer Signal Amplification, Portable Test and Measurement.
Low-Voltage Sensor Conditioning
The TLV2781ID fits sensor-amplifier stages that operate from a 1.8 V to 3.6 V rail and need signal swing close to the supply limits. Its rail-to-rail input capability supports low-level sensor signals near ground, while the 8 MHz gain-bandwidth product provides useful bandwidth for moderate-frequency conditioning. Place the amplifier close to the sensor or protection network, provide normal supply decoupling, and confirm that the input common-mode range covers the full sensor output range. For high-gain configurations, verify noise, offset, bias-current effects, and stability against the manufacturer specifications.
Рекомендуется
Battery-Powered Instrumentation
The TLV2781ID is appropriate for compact, battery-powered instruments that limit both supply voltage and signal bandwidth. Its 1.8 V minimum operating supply supports low-energy designs, while rail-to-rail input/output operation improves usable signal range without requiring a bipolar supply. The 8 MHz bandwidth is suitable for many precision measurement front ends rather than high-speed waveform systems. Check the amplifier's quiescent current for battery-budget calculations, confirm output-current demand, and use the manufacturer's recommended bypass capacitors close to the supply pins.
Рекомендуется
Industrial ADC Input Driver
The TLV2781ID can serve as the analog front-end stage for a low-voltage ADC in industrial control equipment. Rail-to-rail output capability helps preserve signal range between the transducer stage and converter, while 8 MHz bandwidth is generally ample for moderate-rate sampling systems. The key design checks are ADC settling requirements, kickback from the sampling input, and capacitive loading at the amplifier output. Use a small isolation resistor if required, avoid excessive gain-bandwidth product combinations that destabilize the amplifier, and verify operation across the full -40°C to 125°C temperature range.
Рекомендуется
Current-Loop Receiver
The TLV2781ID can be used in a low-voltage current-loop receiver when the loop signal requires a modest bandwidth and rail-to-rail output swing. Its 1.8 V minimum supply suits compact process-control electronics, while the 8 MHz gain-bandwidth product provides more closed-loop capability than a slow precision amplifier. The design must account for the loop's common-mode voltage, input protection, output drive, and the shunt or network forming the transimpedance element. Confirm that the selected operating point remains within the amplifier's input common-mode range.
Рекомендуется
Transducer Signal Amplification
The TLV2781ID is useful for gain and impedance conversion in bridge, strain-gauge, and resistive-transducer front ends operating at low supply voltages. Rail-to-rail input behavior helps preserve small signals near ground, and the 8 MHz bandwidth supports moderate-bandwidth sensor conditioning. However, the amplifier's offset, bias current, noise, and input capacitance can directly influence measurement accuracy. Keep input traces short, use guarded grounding where appropriate, and derive the passive network values from the transducer resistance and required closed-loop gain rather than treating the 8 MHz figure as a universal settling specification.
Рекомендуется
Portable Test and Measurement
The TLV2781ID supports portable measurement equipment that combines low supply voltage, rail-to-rail signal access, and moderate bandwidth. It can amplify probe, sensing, or divider signals without requiring a bipolar supply, and its -40°C to 125°C rating supports equipment intended for industrial environments. Use the rail-to-rail characteristics only after checking the exact output-swing limits because loading and output-current conditions affect headroom. PCB signal integrity is especially important near high-impedance sources, so keep feedback paths short and provide a stable reference or return path for the measured input.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TLV2781ID — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар |
|---|---|
| Package | 8-pin SOIC (D) |
| Brand | Texas Instruments |
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Minimum Supply Voltage | 1.8 V |
| Maximum Supply Voltage | 3.6 V |
| Gain-Bandwidth Product | 8 MHz |
| Input Type | Rail-to-rail |
| Output Type | Rail-to-rail |
| Operating Temperature Range | -40°C to 125°C |
Ключевые отличия
- Supports low-voltage operation with rail-to-rail signal access (против Generic 5 V operational amplifiers)
- Provides moderate bandwidth for compact analog systems (против Low-speed precision operational amplifiers)
- Combines industrial temperature operation with a single-amplifier SOIC format (против Commercial-temperature single op amps)
Заметки по проектированию
Place the power-supply bypass capacitor close to the positive supply and ground pins, and keep the feedback loop compact to minimize parasitic feedback. For sensitive sensor inputs, route the signal over a continuous ground plane and avoid running adjacent to switching-converter nodes. The 8 MHz bandwidth can amplify high-frequency noise and layout effects even when the intended closed-loop bandwidth is much lower, so input and feedback-trace discipline is important.
Do not assume that rail-to-rail input and output means unlimited input range, zero headroom, or unrestricted capacitive drive. Confirm the common-mode range at the actual supply voltage, inspect the output-swing curves under the intended load, and verify stability for the output capacitance and feedback network. The 3.6 V value is a maximum supply rating; operation close to that limit still requires compliance with every other electrical characteristic.
For source impedances near the amplifier's recommended operating range, minimize input capacitance and use a compact guard or isolation resistor if the following stage presents capacitive loading. The 8 MHz gain-bandwidth product can produce peaking or ringing when noise gain rises near crossover, especially with excessive closed-loop gain. Validate stability using the manufacturer's recommended values and the actual source, load, and feedback components before production release.
Design the supply rail below the 3.6 V maximum with margin for tolerances and transient overshoot. Although the amplifier operates from 1.8 V, low supply voltage reduces output headroom and may limit current into heavier loads. Verify the output-current requirement, output-swing margin, and bypass network using the manufacturer datasheet. Do not substitute a higher-voltage amplifier without checking its input common-mode range and output-swing behavior at the lower operating voltage.
Информация о соответствии
Compliance status was not stated in the accessible product information. The manufacturer product and datasheet should be consulted for current environmental, material, and automotive qualification declarations.