TLV2888IDGKR-Q1 - Dual 36V 14MHz Zero-Drift Op Amp | TI
Артикул: TLV2888IDGKR-Q1 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $3.2 | $3,20 |
| 10 | $2.88 | $28,80 |
| 100 | $2.45 | $245,00 |
| 500 | $2.1 | $1.050,00 |
| 1.000 | $1.85 | $1.850,00 |
TLV2888IDGKR-Q1 Обзор
A zero-drift operational amplifier is a precision amplifier architecture that periodically self-corrects its input offset voltage using chopper stabilization or auto-zero techniques. Within the amplifier hierarchy, it sits under operational amplifiers, precision amplifiers, and analog signal-conditioning ICs, delivering DC accuracy that conventional CMOS or bipolar op amps cannot achieve without trimming.
Key features include a maximum input offset voltage of only 15uV, a maximum offset drift of 0.05uV/C over the wide temperature range, rail-to-rail I/O operation, and a very high slew rate with fast settling time enabled by the wide 14MHz bandwidth. The mux-friendly input design minimizes channel-switching glitches when the amplifier follows an analog multiplexer, a common requirement in automotive battery-management and sensor-multiplexed front ends.
Architecturally, the TLV2888 uses a zero-drift CMOS core that suppresses 1/f noise and offset through internal auto-correction, combining the DC precision of chopper amplifiers with the wide AC bandwidth of a fast CMOS output stage. This makes it effective both as a precision DC amplifier and as a high-speed signal-chain buffer.
Typical applications include automotive battery management systems, current-sense amplification after a shunt (pair with INA-family monitors), multiplexed sensor front ends driving ADCs, and industrial precision signal conditioning. The 36V rating tolerates automotive load-dump-adjacent rail conditions.
Design consideration: zero-drift amplifiers generate internal chopping ripple; follow the TI datasheet layout recommendations and verify settle time when driving switched-capacitor ADC inputs. Price references are as of 2026-08-29.
Аналоги без доработки для TLV2888IDGKR-Q1 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с TLV2888IDGKR-Q1 (тот же форм-фактор и посадочное место) — отличается по Amplifier Type, Operating Temperature, Package.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
TLV2888DGKR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TLV2452AIDGKR-Q1
⚡ Тот же корпус ⚠️ Характеристики не проверены✓ В наличии
$0.55 / шт.
Открыть даташит →TLV9152IDGKR
⚡ Тот же корпус ⚠️ Характеристики не проверены✓ В наличии
$0.38 / шт.
Открыть даташит →MCP6V02-E/MS
⚡ Тот же корпус ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
TLV2888IDGKR-Q1 Максимальные параметры и электрические характеристики
| Amplifier Channels | 2 (Dual) |
| Supply Voltage Range | up to 36 V |
| Gain Bandwidth Product | 14 MHz |
| Input Offset Voltage (Max) | 15 uV |
| Offset Voltage Drift (Max) | 0.05 uV/C |
| Amplifier Type | Chopper (Zero-Drift), Mux-Friendly CMOS |
| Тип выхода | Rail-to-Rail |
| Рабочая температура | -40C to +125C (I grade, AEC-Q100 Q1) |
| Корпус | VSSOP-8 (DGK) |
| Тип монтажа | Surface Mount |
| Automotive Qualification | AEC-Q100 (Q1) |
| Статус RoHS | Compliant |
Конфигурация выводов TLV2888IDGKR-Q1
| Контакт 1 | OUT A — Channel A output |
| Контакт 2 | IN A- — Channel A inverting input |
| Контакт 3 | IN A+ — Channel A non-inverting input |
| Контакт 4 | V- — Negative supply / ground |
| Контакт 5 | IN B+ — Channel B non-inverting input |
| Контакт 6 | IN B- — Channel B inverting input |
| Контакт 7 | OUT B — Channel B output |
| Контакт 8 | V+ — Positive supply |
Типичное применение
TLV2888IDGKR-Q1 подходит для 6 применениеs: Automotive Battery Management Systems, Multiplexed Sensor Front Ends, Precision Current Sensing, Industrial Process Control Signal Conditioning, Test and Measurement Instrumentation, Automotive Position and Current Sensor Interfaces.
Automotive Battery Management Systems
The TLV2888IDGKR-Q1 fits BMS cell-monitoring front ends because its 15uV max offset and 0.05uV/C max drift preserve measurement accuracy across the -40C to +125C AEC-Q100 range, while the 36V rating tolerates elevated automotive rail conditions. Placed as a buffer or gain stage between cell-voltage taps and the monitoring ADC, its mux-friendly input handles channel-switching transients, and the 14MHz GBW settles quickly after each mux event - a quantified benefit over conventional op amps that can take microseconds to settle zero-drift errors.
Рекомендуется
Multiplexed Sensor Front Ends
In systems where an analog multiplexer shares one ADC across many sensors, the TLV2888IDGKR-Q1's mux-friendly input stage is purpose-built: it resists offset disturbance from mux charge injection and settles fast thanks to 14MHz GBW and a very high slew rate. The 15uV offset max ensures each channel is measured with equal precision regardless of switching history. Used as a post-mux buffer before the ADC, it prevents signal smearing; the trade-off is zero-drift chopping ripple that should be filtered per TI datasheet layout guidance.
Рекомендуется
Precision Current Sensing
Amplifying small shunt voltages demands microvolt-level offset: the TLV2888IDGKR-Q1's 15uV max offset corresponds to only 1.5mV equivalent error across a 100-ohm transimpedance stage, and near-zero drift keeps calibration valid over the full automotive temperature span. Its rail-to-rail I/O maximizes usable dynamic range on single 5V or 24V rails. As a gain stage following a shunt, the wide 14MHz bandwidth also captures fast load transients that slower precision amplifiers miss, supporting inrush and fault detection.
Рекомендуется
Industrial Process Control Signal Conditioning
For 4-20mA loop receivers and bridge-transducer conditioning, the TLV2888's zero-drift core removes 1/f noise and offset, so a millivolt-level sensor output can be amplified with high gain without DC error dominating. The 36V supply rating directly accommodates 24V industrial rails without pre-regulation, simplifying the analog front end. Rail-to-rail input and output preserve headroom on single-supply designs; designers should account for the 14MHz bandwidth with adequate feedback-network stability measures such as small feedback capacitors.
Рекомендуется
Test and Measurement Instrumentation
Bench instruments and data-acquisition modules benefit from the TLV2888's combination of microvolt DC accuracy and 14MHz AC bandwidth - a rare pairing, since most precision amplifiers are slow and most fast amplifiers drift. The dual channels allow differential front-end topologies in one VSSOP-8 footprint, saving board area. Fast settling after overdrive or mux switching makes it suitable for autoranging scopes and DAQ scanners; the chopping ripple must be assessed against the system noise floor in the highest-resolution modes.
Рекомендуется
Automotive Position and Current Sensor Interfaces
Resistive and Hall-based position sensors in electric power steering and throttle bodies require drift-free amplification over extreme temperatures; the TLV2888IDGKR-Q1's 0.05uV/C max drift and AEC-Q100 qualification directly address this. The rail-to-rail output uses the full ADC input range for maximum resolution of the sensor transfer curve. Its mux-friendly input also suits multi-sensor scanned architectures, and the 36V rating protects against transient rail excursions common in 12V automotive networks.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TLV2888IDGKR-Q1 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TLV2888DGKR | TLV2452AIDGKR-Q1 | MCP6V02-E/MS |
|---|---|---|---|---|
| Package | VSSOP-8 (DGK) | VSSOP-8 (DGK) - same | VSSOP-8 (DGK) - same | MSOP-8 - footprint-verify |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Microchip Technology |
| Gain Bandwidth | 14 MHz | 14 MHz | ~3 MHz | ~2 MHz |
| Automotive AEC-Q100 | Yes (Q1) | No | Yes (Q1) | No |
| Architecture | Zero-drift (chopper), mux-friendly | Zero-drift (chopper), mux-friendly | Conventional CMOS, low power | Zero-drift (chopper) |
Ключевые отличия
- 14MHz GBW with microvolt offset in one part (против TLV2452AIDGKR-Q1)
- Mux-friendly input stage (против MCP6V02-E/MS)
- AEC-Q100 automotive qualification at 36V (против TLV2888DGKR)
Заметки по проектированию
Zero-drift amplifiers generate internal chopping energy that can couple into high-impedance nodes. Place the TLV2888IDGKR-Q1 close to the mux/ADC, keep input traces short and guarded, and follow TI datasheet layout recommendations: solid ground plane under the device, and a 0.1uF ceramic decoupling capacitor within 2mm of the V+ pin with an additional 1uF bulk capacitor nearby.
When driving a switched-capacitor SAR ADC, the 14MHz GBW alone does not guarantee settling - check the datasheet settling-time curves against the ADC acquisition window and add an RC charge-kickback filter if needed. Do not exceed the 36V absolute maximum supply including transients; on 24V industrial rails use a series resistor and clamp if surge is expected.
In multiplexed front ends, insert the amplifier after the mux with gain set so the output swing stays within the linear region across all sensor channels. The mux-friendly input tolerates switching charge injection, but source impedance above a few kilo-ohms still increases settling time; verify per-channel settle with the highest-impedance source in the system.
Информация о соответствии
AEC-Q100 qualified per -Q1 suffix per TI product page. RoHS/lead-free per standard TI ordering data; other fields not stated in provided data.
