TPS23757PWR - PoE+ PD Controller w/ DC-DC, 20-TSSOP | TI
Артикул: TPS23757PWR ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $3.65 | $3,65 |
| 10 | $3.28 | $32,80 |
| 100 | $2.92 | $292,00 |
| 500 | $2.63 | $1.315,00 |
| 1.000 | $2.34 | $2.340,00 |
TPS23757PWR Обзор
What is a PoE Powered Device (PD) controller? A PoE PD controller is the integrated circuit on the device side of an Ethernet cable that negotiates the power contract with the Power Sourcing Equipment (PSE), performs detection, classification, inrush control, and hot-swap functions, and then provides a regulated bulk rail for downstream DC/DC conversion. The TPS23757 combines that front-end PD interface with a current-mode PWM controller, placing both functions in a single chip so the PD only needs the TPS23757, an external power MOSFET, a transformer, and a few passive components to build an isolated PoE power supply.
Key features include 100V-rated hot-swap FET driver for PD pass-through switching, IEEE 802.3at hardware classification with two-event classification signaling support, programmable inrush current limiting, and a wide auxiliary adapter ORing range from 12V to 57V. The integrated DC/DC controller uses peak-current-mode control with programmable slope compensation, supporting both primary-side regulated flyback topologies and forward converters with a single output.
The TPS23757's 100V absolute-maximum input rating exceeds the 802.3at transient tolerance requirement of 100V for 50µs, providing robust line-side protection. Adaptive gate drive and soft-start features minimize inrush stress on the bulk capacitor, while undervoltage lockout and thermal shutdown protect against fault conditions. The TSSOP-20 package with PowerPAD thermal pad offers a thermal resistance of approximately 35 C/W, enabling operation at full PD load without external heatsinking.
Typical applications include IEEE 802.3at Type 1 powered devices such as IP phones, wireless access points, security cameras, IoT gateways, and small-form-factor PoE+ powered equipment. The 13W power level covers a wide range of enterprise networking endpoints.
A key design consideration is the auxiliary adapter ORing: when both PoE and adapter are present, the TPS23757 selects the higher voltage rail and uses the adapter as a seamless backup, useful for installations where wall power is preferred but PoE failover is required.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides.
Аналоги без доработки для TPS23757PWR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с TPS23757PWR (тот же форм-фактор и посадочное место) — отличается по Detection Signature, MSL Level, Operating Temperature Range, Package.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
TPS23757PW
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TPS23757DR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TPS23756PWR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TPS23755PWR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TPS23758PWR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TPS23757PWR Максимальные параметры и электрические характеристики
| Product Type | PoE Powered Device (PD) interface + DC/DC controller |
| PoE Standard | IEEE 802.3at (Type 1, PoE+) and IEEE 802.3af (PoE) |
| Maximum PD Power | 13 W (Class 3) |
| Input Voltage Range (PoE) | 0 V to 57 V (100 V abs max transient) |
| Auxiliary Adapter Range | 12 V to 57 V |
| DC-DC Controller Type | Current-mode PWM (flyback/forward) |
| Internal Hot-Swap FET Drive | Yes, 100 V rated |
| Detection Signature | IEEE 802.3af compliant (25 kΩ) |
| Hardware Classification | Class 0-4 programmable |
| Two-Event Classification | Supported |
| Диапазон рабочих температур | -40 C to +125 C |
| Корпус | 20-TSSOP (PW) with PowerPAD |
| Тип монтажа | Surface Mount |
| Уровень MSL | 2 (1 year floor life) |
| Статус RoHS | Compliant |
| UVLO / OVP / OCP / Thermal Shutdown | Yes / Yes / Yes / Yes |
Конфигурация выводов TPS23757PWR
| Контакт 1 | VDD — Positive input supply from PoE or adapter (via internal ORing) |
| Контакт 2 | RTN — Return path for PoE and adapter inputs |
| Контакт 3 | GND — Analog ground reference |
| Контакт 4 | AUX — Auxiliary adapter input (12 V to 57 V) |
| Контакт 5 | PG — Power good indicator output |
| Контакт 6 | T2P — Two-event classification status output |
| Контакт 7 | DET — Detection signature programming pin |
| Контакт 8 | CLS — Classification programming pin |
| Контакт 9 | VCC — Internal 5 V regulator output |
| Контакт 10 | GATE — Hot-swap FET gate driver output |
| Контакт 11 | SENSE — Hot-swap current sense input |
| Контакт 12 | COMP — PWM control loop compensation node |
| Контакт 13 | CS — Current sense input (peak current mode) |
| Контакт 14 | RT — Oscillator timing resistor |
| Контакт 15 | SS — Soft-start programming pin |
| Контакт 16 | REF — Reference voltage output |
| Контакт 17 | UVLO — Undervoltage lockout programming |
| Контакт 18 | FAULT — Fault indicator output |
| Контакт 19 | NC — Not connected (per datasheet) |
| Контакт 20 | EP — Exposed thermal pad (PowerPAD), connect to GND |
Типичное применение
TPS23757PWR подходит для 6 применениеs: IEEE 802.3at IP Phone Power Supply, Wireless Access Point (Wi-Fi AP), PoE+ Security Camera (IP Surveillance), Industrial IoT Gateway / Sensor Hub, PoE-Powered LED Lighting Controller, Smart Building Access Control Reader.
IEEE 802.3at IP Phone Power Supply
The TPS23757PWR's 13 W Type 1 PD rating and integrated current-mode PWM controller make it an ideal single-chip solution for enterprise IP phones. The internal hot-swap FET driver handles the 100 V IEEE 802.3at line transients while the integrated flyback controller regulates the isolated 5 V or 12 V rail for the phone's baseband and audio subsystems, eliminating the need for a separate PD controller IC and reducing BOM cost.
Рекомендуется
Wireless Access Point (Wi-Fi AP)
PoE-powered Wi-Fi access points typically require 9-13 W delivered to a 5 V or 12 V internal rail. The TPS23757PWR supports this load level across all PoE classes from 1 to 3, while the auxiliary adapter input (12-57 V) allows wall-power operation in installations where PoE infrastructure is not deployed. The wide auxiliary range also supports 24 V passive-PoE adapters deployed in legacy networks.
Рекомендуется
PoE+ Security Camera (IP Surveillance)
Outdoor and indoor IP cameras commonly draw 6-12 W for the imager, IR LEDs, heater, and Ethernet PHY. The TPS23757PWR's integrated classification signature and two-event classification signaling ensure reliable negotiation with 802.3at PSEs at Class 3, while the 100 V transient rating protects against lightning-induced surge events on outdoor cabling. The TSSOP-20 PowerPAD package offers sufficient thermal headroom for continuous 13 W operation.
Рекомендуется
Industrial IoT Gateway / Sensor Hub
Industrial IoT gateways aggregate multiple sensor interfaces and typically require isolated 5 V or 12 V rails from PoE. The TPS23757PWR's flyback controller supports galvanic isolation up to 5 kV with the appropriate transformer, satisfying industrial surge and safety requirements. Hardware UVLO protects against unstable PoE sources, while thermal shutdown guards against overload conditions in high-temperature factory environments.
Рекомендуется
PoE-Powered LED Lighting Controller
Connected LED luminaires powered by PoE use the TPS23757PWR to deliver a regulated constant-current or constant-voltage rail to downstream LED driver stages. The integrated flyback controller simplifies the isolated 24-48 V to 12 V conversion needed for the LED driver IC. The auxiliary adapter input supports direct DC bus powering in commercial installations with central DC distribution.
Рекомендуется
Smart Building Access Control Reader
PoE-powered card readers, door controllers, and intercoms benefit from the TPS23757PWR's single-chip integration. The combined PD interface and flyback controller deliver an isolated 5 V or 12 V rail for the reader electronics, while the auxiliary adapter input supports installations where running Ethernet is impractical but 24 V wall power is available. The compact TSSOP-20 footprint simplifies layout in space-constrained reader housings.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TPS23757PWR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TPS23757PW | TPS23757DR | TPS23756PWR | TPS23755PWR | TPS23758PWR |
|---|---|---|---|---|---|---|
| Package | TSSOP-20 (PW) | TSSOP-20 (PW) - same | SOIC-20 (DR) - different footprint | TSSOP-20 (PW) - same | TSSOP-20 (PW) - same | TSSOP-20 (PW) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| PoE Standard | 802.3at (Type 1) + 802.3af | 802.3at (Type 1) + 802.3af | 802.3at (Type 1) + 802.3af | 802.3af (no at two-event) | 802.3af | 802.3at (Type 1) + 802.3af, PSR support |
| Maximum PD Power | 13 W (Class 3) | 13 W (Class 3) | 13 W (Class 3) | 13 W (Class 3) | 13 W (Class 3) | 13 W (Class 3) |
| Input Voltage (PoE) | 0-57 V (100 V abs max) | 0-57 V (100 V abs max) | 0-57 V (100 V abs max) | 0-57 V (100 V abs max) | 0-57 V (100 V abs max) | 0-57 V (100 V abs max) |
| Adapter Input Range | 12 V to 57 V | 12 V to 57 V | 12 V to 57 V | 12 V to 57 V | 12 V to 57 V | 12 V to 57 V |
| DC-DC Topology | Isolated flyback / forward (current mode) | Isolated flyback / forward (current mode) | Isolated flyback / forward (current mode) | Isolated flyback / forward (current mode) | Non-isolated flyback / forward | Isolated flyback with primary-side regulation |
| Two-Event Classification | Supported | Supported | Supported | Not supported | Not supported | Supported |
Ключевые отличия
- Single-chip PoE+ PD + DC/DC integration (против TPS23755PWR)
- Hardware two-event classification support (против TPS23756PWR)
- Wide auxiliary adapter ORing range (против TPS23754 (earlier family))
Заметки по проектированию
The TSSOP-20 PowerPAD must be soldered to a top-layer copper plane of at least 1 square inch connected to GND to meet the datasheet thermal resistance of approximately 35 C/W theta_JC. Without proper thermal vias to inner ground planes, junction temperature can exceed 125 C at the maximum 13 W PD load, triggering thermal shutdown. Place input bulk capacitors close to the VDD/RTN pins and route the SENSE trace as a Kelvin connection to the current-sense resistor for accurate inrush control.
Keep the high-current loop from VDD through the hot-swap FET to RTN and the bulk capacitor as small and short as possible. Route the CS (current sense) and COMP traces away from the gate driver and switching node to avoid noise coupling into the PWM control loop. Use a ground star-point connection with the analog GND (pin 3) referenced separately from the noisy power GND, joining only at the exposed pad. Estimated: at 13 W continuous load with proper PowerPAD soldering, the junction temperature rise is approximately 35 C/W × 5 W dissipation (typical flyback loss) = 175 C/W × 5 W = no, recompute: 5 W × 35 C/W = 175 C rise, which exceeds the 125 C limit; designers should verify thermal performance in their specific application.
Do not omit the TVS diode across VDD-RTN for IEEE 802.3at transient protection; the 100 V abs max rating is for very short durations and does not survive continuous surge events. The detection signature resistor must be exactly 25 kΩ with low tolerance (1% or better) to pass the IEEE signature check; many first-prototype failures are caused by incorrect detection resistance. Ensure the auxiliary adapter voltage never exceeds 57 V during load-dump transients or the internal ORing MOSFET may be damaged.
Estimated: at full 13 W PD load with 48 V PoE input and 5 V/2.6 A output through a typical flyback converter, the TPS23757PWR dissipates approximately 1.5-2 W (controller and gate-drive losses). Junction temperature rise = 2 W × 35 C/W = 70 C above ambient. For operation above 55 C ambient, derate the maximum PD power or add external thermal management to maintain junction temperature below 125 C.
Select the flyback transformer turns ratio to provide a VDS stress on the primary MOSFET well below the 150 V rating of typical 100 V-rated MOSFETs at maximum input. The TPS23757PWR's 50% maximum duty cycle clamp protects against transformer saturation but designers should still verify DCM/CCM boundary at minimum load. Program the soft-start capacitor (SS pin) for inrush times of 5-10 ms to balance startup stress against detection-cycle timing requirements.
Информация о соответствии
RoHS and lead-free compliant per TI product page. Not AEC-Q100 qualified; for automotive PoE applications consult TI's automotive-grade PoE PD family. Supports IEEE 802.3at and IEEE 802.3af standards.
