TPS61096ADSSR - 28V Boost Converter, 1µA IQ | Texas Instruments
Артикул: TPS61096ADSSR ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $1.32 | $1,32 |
| 10 | $1.18 | $11,80 |
| 100 | $0.97 | $97,00 |
| 500 | $0.85 | $425,00 |
| 1.000 | $0.74 | $740,00 |
| 3.000 | $0.62 | $1.860,00 |
TPS61096ADSSR Обзор
A boost converter (step-up DC-DC switching regulator) is a power management integrated circuit that raises a lower DC input voltage to a higher DC output voltage using an inductor, switch, and rectifier network. It belongs to the broader hierarchy of switching voltage regulators, then voltage regulators, then power management ICs. The TPS61096A family is specifically optimized for ultra-low standby current to extend battery life in always-on systems.
Key features of the TPS61096ADSSR include true shutdown isolation, internal synchronous MOSFETs, output disconnect during shutdown, programmable output voltage via an external resistor divider, and integrated soft-start. Thermal shutdown and over-current protection safeguard the device under fault conditions. The 1µA quiescent current is among the lowest in its class, making this regulator exceptionally well suited to IoT nodes, wearables, and metering applications that spend most of their operational life in standby.
The TPS61096ADSSR uses a peak-current-mode control architecture with a fixed internal switching frequency (typically around 1 MHz, depending on variant), enabling a small 4.7µH inductor. Synchronous rectification eliminates the need for an external Schottky diode, shrinking the BOM and improving efficiency at heavy loads. The output disconnect feature prevents reverse current flow from VOUT back through the inductor to the battery when the converter is disabled, preserving battery energy and protecting the system.
Typical applications include smart meters and gas/water AMR modules, ePaper and e-ink displays, two-cell alkaline-powered toys and portable instruments, single-cell Li-Ion powered OLED bias supplies, and low-power wireless sensor nodes. The wide output range of 4.5V to 28V also supports bias rails for TFT displays, IGBT gate drivers, and piezo buzzer excitation.
When designing with this part, ensure the inductor has a saturation current rating at least 30% above the peak switch current to prevent saturation at cold temperatures. Place the input capacitor, output capacitor, and bootstrap capacitor as close to the IC as possible. The output disconnect feature must be considered when cascading boost stages.
This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not consolidated in the manufacturer datasheet.
Аналоги без доработки для TPS61096ADSSR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
TPS61096ADSST
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TPS61096DSSR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TPS61096ADSSR Максимальные параметры и электрические характеристики
| Топология | Synchronous Boost (Step-Up) |
| Диапазон входного напряжения | 1.8 V to 5.5 V |
| Диапазон выходного напряжения | 4.5 V to 28 V (adjustable) |
| Switch Current | 350 mA |
| Ток покоя | 1 µA (ultra-low) |
| Корпус | WSON-12 (DSS) 3x3 mm with Exposed Pad |
| Число выводов | 12 |
| Тип монтажа | Surface Mount |
| Рабочая температура | -40 °C to +125 °C |
| Output Disconnect | Yes (true shutdown) |
| Синхронный выпрямитель | Yes (internal MOSFETs) |
| Плавный пуск | Yes (internal) |
| Тепловая защита | Yes |
| Over-Current Protection | Yes |
| Статус RoHS | Compliant |
Конфигурация выводов TPS61096ADSSR
| Контакт 1 | SW — Switch node - inductor connection |
| Контакт 2 | SW — Switch node - inductor connection |
| Контакт 3 | VIN — Input supply voltage |
| Контакт 4 | EN — Enable input (active high) |
| Контакт 5 | GND — Ground |
| Контакт 6 | AGND — Analog ground |
| Контакт 7 | FB — Feedback voltage (set VOUT via resistor divider) |
| Контакт 8 | VOUT — Regulated output voltage |
| Контакт 9 | VOUT — Regulated output voltage |
| Контакт 10 | NC — Not connected (per datasheet) |
| Контакт 11 | NC — Not connected (per datasheet) |
| Контакт 12 | PGND — Power ground (exposed pad) |
Типичное применение
TPS61096ADSSR подходит для 6 применениеs: Smart Meter AMR Modules, ePaper and E-Ink Display Bias, Two-Cell Alkaline Portable Instruments, Single-Cell Li-Ion OLED Bias Supply, Low-Power Wireless Sensor Nodes, TFT Display and IGBT Gate Driver Bias.
Smart Meter AMR Modules
The TPS61096ADSSR's 1µA quiescent current and 28V output capability make it ideal for automatic meter reading (AMR) modules in gas, water, and electricity meters. The wide 4.5V to 28V output range drives LCD bias rails and piezo buzzer drivers, while the ultra-low IQ preserves battery life across 10+ year field deployments. The WSON-12 footprint fits inside compact meter enclosures, and the 1.8V to 5.5V input range accommodates single-cell Li-SOCl2 or two-cell alkaline primary batteries common in metering applications.
Рекомендуется
ePaper and E-Ink Display Bias
The TPS61096ADSSR provides the adjustable high-voltage rail required by ePaper and e-ink display gate and source drivers. Its 4.5V to 28V output range covers typical VCOM voltages (typically ±15V to ±25V for symmetric drive), and the 1µA quiescent current minimizes standby drain between page refresh events, which can be hours or days apart. The output-disconnect feature prevents reverse leakage into the battery when the display is idle, and the small WSON-12 package allows placement directly beneath the display flex cable.
Рекомендуется
Two-Cell Alkaline Portable Instruments
The TPS61096ADSSR operates from 1.8V to 5.5V, making it well suited for two-cell alkaline (2.0V to 3.2V) powered handheld instruments such as digital calipers, laser distance meters, and portable gas detectors. It boosts the depleted battery voltage up to 28V for sensor excitation, photo-detector bias, or OLED panel supply. The synchronous topology and integrated MOSFETs reduce BOM count and PCB area, while the internal soft-start prevents inrush current that could trigger battery protection circuits at low temperatures.
Рекомендуется
Single-Cell Li-Ion OLED Bias Supply
The TPS61096ADSSR steps a single Li-Ion cell (3.0V to 4.2V) up to the 12V to 18V AVDD rail required by small OLED displays in wearable and IoT devices. Its 350 mA switch current and synchronous rectification deliver peak load currents required for OLED pixel refresh, while 1µA quiescent current preserves battery life during display-off intervals. The exposed thermal pad of the WSON-12 package provides efficient heat extraction for continuous-operation wearable scenarios.
Рекомендуется
Low-Power Wireless Sensor Nodes
The TPS61096ADSSR is well matched to battery-powered wireless sensor nodes that transmit periodically from a high-impedance sensor source. Its 1µA quiescent current means the boost converter contributes negligible standby drain between transmissions, and the 28V output can bias electrochemical gas sensors, PIR motion sensors, or piezoelectric accelerometers. The output disconnect feature is critical here because many sensors hold their bias voltage across the measurement window, and any reverse leakage would degrade measurement accuracy.
Рекомендуется
TFT Display and IGBT Gate Driver Bias
The TPS61096ADSSR delivers the 18V to 24V bias rail required by TFT-LCD gate drivers and IGBT gate driver bootstrap networks from a 3.3V or 5V logic rail. The 28V maximum output range provides design margin for IGBT high-side drive circuits, and the synchronous topology eliminates the need for an external Schottky diode, reducing both BOM cost and PCB area. The 1µA quiescent current is well below the leakage of most gate-driver bootstrap capacitors, so disabling the converter cleanly turns off the high-side drive.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TPS61096ADSSR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TPS61096ADSST | TPS61096DSSR |
|---|---|---|---|
| Package | WSON-12 (DSS) | WSON-12 (DSS) - same | WSON-12 (DSS) - same |
| Brand | Texas Instruments | Texas Instruments - same | Texas Instruments - same |
| Input Voltage Range | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Output Voltage Range | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 28 V |
| Switch Current | 350 mA | 350 mA | 350 mA |
| Quiescent Current | 1 µA | 1 µA | 1 µA |
| Output Disconnect | Yes | Yes | Yes |
| Reel Suffix | ADSSR (large reel) | ADSST (small reel) | DSSR (non-A variant) |
Ключевые отличия
- 28V output from sub-5V input (против TPS61236PWP)
- 1µA ultra-low quiescent current (против TPS61090)
- True output disconnect during shutdown (против TPS61161ADRVR)
Заметки по проектированию
Estimated: at VIN=3.7V (Li-Ion), VOUT=18V, IOUT=50mA, the TPS61096ADSSR dissipates roughly 0.42W in the high-side MOSFET during boost operation. With the WSON-12 exposed-pad thermal resistance of approximately 50 C/W on a 1-square-inch copper pour, this yields a junction temperature rise of ~21°C above ambient - well within the 125°C rating, but verify with the manufacturer's SOA curve if operating at the full 350mA switch current.
Place the input capacitor (≥4.7µF ceramic), output capacitor (≥1µF ceramic), and bootstrap capacitor as close as possible to the VIN, VOUT, and SW pins respectively to minimize switching-node ringing and EMI. Use a continuous ground plane tying GND, AGND, and PGND (the exposed pad) together at a single star point beneath the IC. Route the SW node traces as short and wide as possible to reduce parasitic inductance.
Do not exceed 28V on VOUT or 5.5V on VIN - the device has no over-voltage protection at the output and the input ESD diodes will clamp at 6V. Choose an inductor with saturation current at least 30% above the peak switch current (typically 350mA × 1.3 ≈ 460mA) to prevent saturation at cold temperatures. The EN pin must not be left floating - tie it to VIN through a 100kΩ resistor if not actively driven.
Информация о соответствии
RoHS compliant per TI product page. Not AEC-Q100 qualified - this is an industrial/consumer grade part.
