W78E054B40FL - 8-Bit 40MHz 16KB Flash MCU | Nuvoton
Артикул: W78E054B40FL ✗ Снят с производстваW78E054B40FL Обзор
An 8051 microcontroller is an embedded processor category designed around a compact instruction set, integrated memory, timers, serial interfaces, and general-purpose I/O. The W78 series extends the classic 8051 architecture with an integrated Flash program memory implementation. These devices occupy the MCU hierarchy between general-purpose microprocessors and simpler fixed-function logic, making them useful for appliance controls, small industrial systems, access equipment, and compact embedded products.
The W78E054B40FL combines 16KB of Flash program memory with 256 bytes of RAM. Its 36 available I/O lines provide interface capacity for sensors, switches, displays, actuators, and external control logic. The 40 MHz operating capability supports faster instruction execution than lower-frequency 8051 derivatives, while the 44-BQFP package exposes enough pins for parallel control and multiple peripheral connections.
The part belongs to the W78E family and uses an 8051-compatible core with integrated Flash memory. Its operating architecture is intended for small embedded control systems where deterministic behavior, compact software, and a moderate peripheral set are more important than a high-performance CPU core or large application-memory footprint. Its 256-byte RAM limits complex buffering and encourages designs to use external memory only when the application genuinely requires it.
Typical uses include appliance and equipment controllers, small motor or relay control panels, sequential industrial modules, instrumentation interfaces, and compact 8-bit embedded platforms. The 36 I/O pins make the device practical for systems combining digital inputs, output control, communication signaling, and status indication without requiring a larger package.
Designers should verify oscillator, reset, timing, and interrupt assignments against the manufacturer datasheet before laying out the PCB. Because the 8051 architecture is memory-constrained, firmware should avoid unnecessary library overhead and preserve stack space for interrupt service routines. The 44-pin BQFP footprint also requires adequate clearance for fine-pitch routing and careful assembly inspection.
This product page consolidates the confirmed architecture, memory, speed, pin-count, package, lifecycle, sourcing, and cross-reference information for the W78E054B40FL. It also highlights the engineering constraints engineers should evaluate when planning a replacement, including memory capacity, timing, package compatibility, pin behavior, firmware dependencies, and legacy-production risk.
Аналоги без доработки для W78E054B40FL — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Для этого товара нет аналогов без доработки.
Запросить аналогиW78E054B40FL Максимальные параметры и электрические характеристики
| Microcontroller Type | 8-bit 8051 W78 microcontroller |
| Maximum CPU Frequency | 40 MHz |
| Program Memory Size | 16KB (16K x 8) Flash |
| RAM Size | 256 bytes (256 x 8) |
| Number of I/O Pins | 36 pins |
| Корпус | 44-pin BQFP |
| Instruction Set Architecture | 8051 |
| Series | W78 series |
| Тип монтажа | Surface mount |
Руководство по цоколевке W78E054B40FL в корпусе 44-pin bqfp
Цоколевка для W78E054B40FL (корпус 44-pin bqfp). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для W78E054B40FL.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
W78E054B40FL подходит для 6 применениеs: Legacy Equipment Controllers, Appliance and Household Device Control, Small Motor and Relay Control, Instrumentation and Data Acquisition Front Ends, Access and Security Control Modules, Communication and Protocol Concentrators.
Legacy Equipment Controllers
The W78E054B40FL fits legacy equipment controllers that retain an 8051 software base and require the original 44-pin BQFP interface. Its 40 MHz operating capability supports responsive control logic, while 16KB of Flash provides space for startup routines, state machines, parameter tables, and communication handlers. The 36 I/O lines can supervise switches, alarm signals, relay outputs, and status indicators. Because the device is obsolete, engineers should preserve its memory map, interrupt structure, and peripheral configuration when maintaining installed platforms, and confirm availability, traceability, and temperature requirements before committing a design to continued production.
Рекомендуется
Appliance and Household Device Control
The W78E054B40FL can manage compact appliance functions where a deterministic 8-bit controller is preferable to a higher-power processor. Its 36 I/O lines support buttons, mode indicators, display segments, sensors, and actuator commands, while 16KB of Flash accommodates a focused state machine rather than a large operating system. The 40 MHz clock rate provides execution margin for scanning inputs, updating displays, and coordinating timing. For connected appliances, the MCU can serve as a local controller while external circuitry handles network connectivity. Firmware planning should account for the 256-byte RAM limit and minimize interrupt-time operations and deep call chains.
Рекомендуется
Small Motor and Relay Control
The W78E054B40FL is applicable to compact relay, solenoid, and small-motor control modules where deterministic sequencing and ample I/O are more important than complex computation. Its 36 I/O lines can distribute digital input sensing and control outputs across the board, while 40 MHz operation supports timely task execution. The 8051 core is familiar in established control codebases, reducing migration effort when maintaining a mature machine. Designers must use the manufacturer datasheet to confirm whether each required timer, PWM, and capture function is present, and they must add suitable driver, protection, and isolation circuits for inductive loads.
Рекомендуется
Instrumentation and Data Acquisition Front Ends
The W78E054B40FL can serve as the supervisory controller in a compact instrumentation front end that multiplexes sensors, controls measurement sequencing, and converts results into local display or communications output. Its 16KB Flash capacity suits bounded acquisition routines and configuration data, and its 36 I/O lines can interface with external amplifiers, converters, and digital sensors. The 256-byte RAM requires streaming or periodic processing rather than retaining large sample buffers. Designers should confirm the available analog and serial peripherals in the datasheet, maintain careful grounding between analog and digital sections, and provide filtering appropriate to the measured signal bandwidth.
Рекомендуется
Access and Security Control Modules
The W78E054B40FL is suitable for compact access-control modules that supervise credential inputs, indicator outputs, lock or relay commands, and local event handling. The 36 I/O lines provide sufficient parallel connectivity for keys, status LEDs, alarm signals, and door-control elements, while 16KB of Flash supports a fixed control program and parameter tables. The 8051 architecture remains practical where firmware is already established and deterministic timing is required. Security deployments should add appropriate credential validation and communication isolation rather than treating the MCU alone as a cryptographic boundary. For new installations, a currently supported MCU with greater memory may simplify long-term maintenance.
Рекомендуется
Communication and Protocol Concentrators
The W78E054B40FL can support a small protocol-concentrator or interface bridge when the required traffic remains modest and the system prioritizes deterministic 8-bit processing. Its 40 MHz clock rate handles protocol timing, status tracking, and routing between serial interfaces, while the 36 I/O lines provide handshake and status signals around external interface components. The 16KB Flash footprint is suitable for compact protocol stacks and fixed configuration tables, although the 256-byte RAM limits buffering depth. Engineers should verify the exact UART, timer, and interrupt resources in the manufacturer datasheet, validate bus timing under worst-case interrupt load, and isolate external communication lines where needed.
Рекомендуется
Справочные инженерные данные для W78E054B40FL — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар |
|---|---|
| Brand | Nuvoton Technology Corporation |
| Package | 44-pin BQFP |
| CPU Architecture | 8-bit 8051 |
| Maximum CPU Frequency | 40 MHz |
| Program Memory | 16KB (16K x 8) Flash |
| RAM | 256 bytes (256 x 8) |
| I/O Pin Count | 36 pins |
| Lifecycle Status | Obsolete |
Ключевые отличия
- Defined legacy 8051 control platform (против No confirmed drop-in alternative)
- High I/O availability within a 44-pin package (против No confirmed drop-in alternative)
- On-chip Flash program memory (против No confirmed drop-in alternative)
Заметки по проектированию
Do not treat every one of the 44 physical BQFP positions as a general-purpose I/O. The device has 36 listed I/O pins, so the remaining positions serve power, ground, clock, reset, programming, or other dedicated functions. Assign PCB connections from the manufacturer pin-description table, confirm each signal's direction and electrical limits, and preserve the original land pattern when replacing an obsolete assembly.
Route the 44-BQFP footprint as a controlled, fine-pitch assembly and avoid long copper stubs beneath the device. Keep clock and reset traces short, provide a clean local return path, and place required bypass capacitors at the supply pins using the datasheet reference layout. Because obsolete parts may have uncertain sourcing provenance, inspection criteria should include solderability, pin condition, marking consistency, and traceability.
Design the supply path around the manufacturer's operating and absolute-maximum voltage limits rather than around the 40 MHz clock rating alone. Use separate routing for sensitive signals, account for startup and reset behavior, and verify that power-supply transients remain within the specified limits. If the original equipment uses a nonstandard clock or reset network, preserve and validate that configuration during any drop-in sourcing review.
The 256-byte RAM is the principal firmware constraint. Avoid deep recursion, large local buffers, and blocking communication routines that can overrun memory during interrupts. Place frequently used data in the limited RAM region, measure worst-case stack depth, and keep time-critical handlers short. A replacement should be checked for equivalent RAM addressing and code-generation behavior, not merely for matching Flash capacity.
Информация о соответствии
No explicit compliance declaration for this exact MPN appears in the available product records. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals status with the current manufacturer or authorized supply channel before environmental or regulatory use.