XC9536XL-7CSG48I - 36-Macrocell 3.3V CPLD | AMD
Артикул: XC9536XL-7CSG48I ✓ АктивенXC9536XL-7CSG48I Обзор
A CPLD is a user-programmable semiconductor that combines configurable logic and programmable interconnect structures. It belongs to the FPGA and CPLD category, where an FPGA provides broad gate-level programmability and a CPLD provides a more structured macrocell architecture for control logic, decoding, interface bridging, and fixed-function state machines. The XC9536XL family combines repeatable timing, nonvolatile configuration, and in-system programmability without the resource complexity of a large FPGA.
The XC9500XL architecture provides 36 macrocells and 36 I/O positions. The device operates from a 3 V to 3.6 V internal supply and supports at least 10,000 program or erase cycles. The -7 grade provides a 7.5 ns maximum propagation delay, while the -I suffix identifies the industrial temperature option. Its 48-CSBGA package reduces board area compared with leaded packages but requires careful assembly and escape-routing planning because signal access beneath the BGA is constrained.
The XL designation refers to the extended XC9500 architecture, while CSG48 identifies the package family and pin count. This device is useful when the design must be implemented as a compact, deterministic logic block rather than a processor-based solution. In-system programmability allows configuration updates, boot-time personality selection, or field reconfiguration when supported by the surrounding system architecture. The manufacturer datasheet remains the controlling reference for pin assignments, configuration behavior, timing, and absolute electrical limits.
Typical uses include industrial control logic, peripheral address decoding, data-format conversion, bus-interface translation, compact coprocessor logic, legacy protocol handling, and system-boot coordination. The 36-macrocell capacity is particularly appropriate for multiple state machines, latch arrays, and combinational control paths. Designs requiring substantially more parallel logic, block RAM, high-speed transceivers, or soft processors should use a larger programmable-logic device instead.
PCB implementation should prioritize BGA fanout, uninterrupted ground-plane continuity, and short connections to bypass capacitors. Because the 48-CSBGA footprint provides dense underside access, a multilayer board with solid ground planes is generally preferable to a two-layer assembly. Validate assembly capability, solder-paste volume, via-in-pad requirements, and component spacing against the manufacturer package drawing before release.
This product page combines the XC9536XL device characteristics, verified distributor availability, same-package replacement analysis, comparison parameters, and practical implementation guidance. It helps engineers determine whether the XC9536XL-7CSG48I offers the required logic density, timing, voltage, package, and lifecycle fit before beginning a PCB or firmware design.
Аналоги без доработки для XC9536XL-7CSG48I — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с XC9536XL-7CSG48I (тот же форм-фактор и посадочное место) — отличается по Package, Architecture, RoHS Status, Temperature Grade, Device Type.
XC9536XL-7CSG48C
✅ Прямая заменаУточнить цену
Открыть даташит →XC9536XL-7CS48I
✅ Прямая заменаУточнить цену
Открыть даташит →XC9536XL-5CSG48C
✅ Прямая заменаУточнить цену
Открыть даташит →XC9536XL-10CSG48C
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
XC9536XL-7CS48C
✅ Прямая заменаУточнить цену
Открыть даташит →XC9536XL-7CSG48I Максимальные параметры и электрические характеристики
| Product Type | Complex Programmable Logic Device (CPLD) |
| Architecture | XC9500XL |
| Macrocell Count | 36 macrocells |
| Programmable Logic Capacity | 800 gates |
| I/O Count | 36 I/O |
| Maximum Propagation Delay | 7.5 ns |
| Maximum Frequency | 178.6 MHz |
| Internal Supply Voltage | 3.3 V nominal |
| Рабочее напряжение питания | 3 V to 3.6 V |
| Process Technology | 0.35 um CMOS |
| Programmable Elements | 2 logic elements per macrocell |
| Program and Erase Endurance | 10,000 cycles minimum |
| In-System Programmability | Supported |
| Корпус | 48-CSBGA, 7 x 7 mm |
| Тип монтажа | Surface Mount |
| Temperature Grade | Industrial |
Руководство по цоколевке XC9536XL-7CSG48I в корпусе 48-csbga, 7 x 7 mm
Цоколевка для XC9536XL-7CSG48I (корпус 48-csbga, 7 x 7 mm). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для XC9536XL-7CSG48I.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
XC9536XL-7CSG48I подходит для 6 применениеs: Industrial Control and Sequencing Logic, Peripheral Address Decoding, Legacy Bus Interface Translation, Data Format Conversion, System Boot and Configuration Control, Instrumentation and Test Logic.
Industrial Control and Sequencing Logic
The XC9536XL-7CSG48I fits compact industrial controllers that require deterministic state machines, interlocks, and command sequencing without a processor. Its 36 macrocells provide room for multiple parallel control paths, while the 7.5 ns maximum propagation delay supports predictable combinational decisions. The industrial -I ordering option is appropriate when ambient conditions exceed the commercial envelope. Place the CPLD near the controlled interfaces, preserve uninterrupted ground planes beneath the BGA, and use the manufacturer timing report to establish setup and hold requirements for attached sensors, actuators, and safety-related interlocks.
Рекомендуется
Peripheral Address Decoding
The XC9536XL-7CSG48I can implement deterministic peripheral address decoding, register selection, chip-enable generation, and bus-cycle qualification. Thirty-six macrocells allow decoding logic to be combined with small state machines rather than splitting one function across multiple devices. The 178.6 MHz listed maximum-frequency figure and 7.5 ns propagation delay provide useful timing margin for synchronous control logic. Engineers should define propagation requirements for every decoded address and qualify the design against the worst-case timing conditions in the AMD datasheet rather than relying only on the nominal frequency figure.
Рекомендуется
Legacy Bus Interface Translation
The XC9536XL-7CSG48I is suitable for translating or coordinating legacy bus signals when the required logic is mainly combinatorial or uses a small number of registered state machines. The 36 available I/O positions can support parallel data, address, and control paths within a single 48-CSBGA device. Designers should partition inputs according to voltage and timing constraints, account for I/O enable behavior, and verify all setup, hold, and transition limits against the manufacturer electrical specification. A multilayer PCB is preferable because it provides continuous plane references while preserving the escape-routing needed for the fine-pitch BGA.
Рекомендуется
Data Format Conversion
The XC9536XL-7CSG48I can implement parallel-to-serial formatting, byte alignment, bit-field rearrangement, and protocol pre-processing where deterministic hardware behavior is important. Its approximately 800-gate capacity is enough for multiple conversion paths and associated control states, reducing reliance on microcontroller firmware. The 7.5 ns maximum propagation delay must be evaluated against the input clock period and output skew budget. For high-speed interfaces, use registered I/O paths where required and validate timing with realistic board-level assumptions rather than treating device propagation delay as the complete system timing budget.
Рекомендуется
System Boot and Configuration Control
The XC9536XL-7CSG48I can coordinate power sequencing, reset generation, mode selection, and peripheral enables during system startup. Because it supports in-system programmability, the same device can also serve as a compact platform controller that manages configuration updates and boot personality selection. Design the programming interface for electrical compatibility and add appropriate write-protection or recovery behavior for critical systems. The configuration data must remain stable according to the manufacturer's power-up and programming requirements, while decoupling and BGA power-ball connections must be designed to prevent unintended resets during supply ramp-up.
Рекомендуется
Instrumentation and Test Logic
The XC9536XL-7CSG48I is useful in instrumentation and test systems for pattern generation, trigger coordination, channel gating, and measurement sequencing. The compact 36-macrocell implementation can consolidate control functions that would otherwise occupy multiple discrete logic devices. Its deterministic 7.5 ns maximum propagation delay helps define trigger relationships, although external propagation delay, connector loading, and clock skew must be included in the end-to-end timing budget. Use short, impedance-controlled routes for sensitive timing signals and maintain a continuous reference plane to minimize coupling between the CPLD, test connectors, and adjacent analog circuitry.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для XC9536XL-7CSG48I — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | XC9536XL-7CSG48C | XC9536XL-7CS48I | XC9536XL-5CSG48C | XC9536XL-10CSG48C | XC9536XL-7CS48C |
|---|---|---|---|---|---|---|
| Brand | AMD | AMD | AMD | AMD | AMD | AMD |
| Package | 48-CSBGA (7x7 mm) | 48-CSBGA (7x7 mm) | 48-CSBGA (7x7 mm) | 48-CSBGA (7x7 mm) | 48-CSBGA (7x7 mm) | 48-CSBGA (7x7 mm) |
| Architecture | XC9500XL | XC9500XL | XC9500XL | XC9500XL | XC9500XL | XC9500XL |
| Macrocell Count | 36 macrocells | 36 macrocells | 36 macrocells | 36 macrocells | 36 macrocells | 36 macrocells |
| Programmable Gate Capacity | 800 gates | 800 gates | 800 gates | 800 gates | 800 gates | 800 gates |
| Maximum Propagation Delay | 7.5 ns | 7.5 ns | 7.5 ns | 5 ns | 10 ns | 7.5 ns |
| Internal Supply Voltage | 3.3 V nominal; 3 V to 3.6 V operating range | 3.3 V nominal; 3 V to 3.6 V operating range | 3.3 V nominal; 3 V to 3.6 V operating range | 3.3 V nominal; 3 V to 3.6 V operating range | 3.3 V nominal; 3 V to 3.6 V operating range | 3.3 V nominal; 3 V to 3.6 V operating range |
| Temperature Grade | Industrial | Commercial | Industrial | Commercial | Commercial | Commercial |
Ключевые отличия
- Faster timing grade than the XC9536XL-10CSG48C option (против XC9536XL-10CSG48C)
- Industrial-temperature ordering option (против XC9536XL-7CSG48C)
- More timing margin than the 10 ns family option (против XC9536XL-10CSG48C)
- Lower device propagation delay than the slower family variant (против XC9536XL-10CSG48C)
Заметки по проектированию
Design the 48-CSBGA footprint directly from the manufacturer package drawing rather than approximating it from a generic BGA library. Confirm ball pitch, pad diameter, solder-mask opening, component orientation, and whether an exposed thermal or configuration-related ball is present. Escape-routing should use vias immediately outside the BGA where practical, while preserving access to every power and ground ball. Because no complete public pin list is reproduced on this page, cross-check the PCB netlist against the pin-description table in the AMD datasheet before fabrication.
Route the 3.3 V supply and ground networks on dedicated layers with short, low-impedance paths to the appropriate BGA balls. Place the manufacturer's recommended local bypass capacitors adjacent to the device, and account for capacitor effective capacitance and DC-bias derating at 3.3 V. Avoid splitting a ground ball connection with narrow traces merely to gain routing space; a multilayer stackup with uninterrupted ground planes is generally more effective for a dense BGA carrying clocked or high-switching-rate I/O.
Use the -7 grade only after completing worst-case timing analysis. A 7.5 ns maximum propagation delay describes device timing under specified conditions; it does not include clock skew, routing delay, connector delay, or external driver loading. Constrain clocks and high-speed I/O, use short point-to-point routes where possible, and avoid crossing plane splits. For replacement with XC9536XL-10CSG48C, recalculate every timing path because the propagation delay increases by approximately 33% from 7.5 ns to 10 ns.
Do not treat the closely related XC9536XL-7CS48I, XC9536XL-7CSG48C, and XC9536XL-7CS48C as identical ordering codes. Compare the speed suffix, package code, temperature suffix, pin description, and qualification requirements as one complete configuration. A PCB footprint match alone does not establish functional equivalence if the commercial-temperature option cannot meet the product's ambient requirements or if a package code changes a ball assignment. Record the full approved manufacturer part number in the schematic, BOM, and production-test documentation.
Информация о соответствии
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for this ordering code. The industrial -I suffix identifies a temperature grade, not automotive qualification.