ADC/DAC
Mga Produkto (2,700+)
AD976CRZ - 16-Bit 100 kSPS SAR ADC | Analog Devices
The Analog Devices AD976CRZ is a 16-bit, 100 kSPS successive-approximation analog-to-digital converter with one analog input, a high-speed parallel output interface, and a 28-pin SOIC package. It operates from a single 5 V supply and uses an internal 2.5 V reference. The converter combines switched-capacitor sampling and successive-approximation conversion to provide a direct digital representation of an analog input while keeping system power requirements comparatively low. An ADC is an interface IC that converts a continuously varying analog voltage into a digital code. Within the broader semiconductor hierarchy, the AD976 is a data-conversion IC within the ADC/DAC category. Its 16-bit resolution provides 65,536 possible digital codes, while the 100 kSPS throughput supports applications that require accurate conversion without the conversion time associated with lower-rate general-purpose data converters. Key features of the AD976CRZ include 16-bit resolution, a 100 kSPS maximum throughput rate, single-supply 5 V operation, an internal 2.5 V reference, and a parallel output interface. The architecture supports acquisition systems, communications equipment, instrumentation, and industrial control applications where the sampled analog signal must be presented to downstream logic or a digital processor. Internally, the AD976 uses a switched-capacitor successive-approximation ADC. The sampling network captures the analog input before the conversion process compares successive bit decisions. The manufacturer documentation identifies an internal 2.5 V reference and describes external 200 ohm and 33.2 kilohm resistors that provide offset and gain compensation for the single-supply configuration. These compensation components are functional parts of accurate system implementation rather than optional signal-conditioning accessories. Typical uses include communications receivers, data-acquisition modules, industrial measurement systems, digital audio and control equipment, and embedded processing platforms. The parallel interface can reduce output multiplexing complexity compared with serial converters when the receiving system can provide enough digital input connections and acquire the converted code at the supported rate. Circuit implementation requires careful attention to analog signal conditioning, reference behavior, digital timing, and the ADC supply. Input and output transitions should be controlled so that switching activity does not degrade conversion accuracy, while the manufacturer's compensation values and recommended layouts should be followed exactly. The AD976CRZ is also offered in related AD976 and AD976A families, but the AD976A doubles the stated throughput to 200 kSPS and should not be treated as an automatic drop-in replacement. This product page combines verified manufacturer and distributor data, package information, pricing context, application guidance, and engineering selection notes. It also distinguishes the AD976's 100 kSPS rating from the faster AD976A, helping engineers identify whether a related converter changes system timing or requires additional validation.
AD977ABR - 16-Bit 200kSPS Serial SAR ADC | 20-SOIC | ADI
The Analog Devices AD977ABR is a 16-bit, 200 kSPS successive-approximation (SAR) analog-to-digital converter with a serial I/O interface, packaged in a 20-pin SOIC (R-20) wide-body surface-mount package. It operates from a single +5 V supply, dissipating a maximum of 100 mW, and supports input ranges of 0 V to 5 V (unipolar), 0 V to 4 V (unipolar), ±5 V (bipolar) and ±3.3 V (bipolar) via factory-trimmed or user-configurable scaling resistors. The SAR architecture with internal conversion clock and auto-calibrating capacitive DAC achieves true 16-bit performance with no missing codes over the industrial temperature range. An ADC (analog-to-digital converter) is a data-converter integrated circuit that samples a continuous analog input voltage and produces a corresponding digital code at its output. SAR ADCs use a binary-search successive-approximation register together with an internal DAC to resolve each conversion in N clock cycles for N-bit precision; they are valued for zero pipeline latency, deterministic behavior, low power, and excellent DC linearity. SAR converters occupy a unique position in the data-converter hierarchy between high-speed flash/pipeline ADCs (>10 MSPS) and slow integrating/sigma-delta ADCs (audio, precision DC). The AD977A family is one of the classic low-power industrial SAR ADCs of the 1990s and remains in production for installed-base applications. Key features include an aperture delay of 5 ns, track-and-hold bandwidth of 2 MHz, and a power-down mode that reduces quiescent dissipation to 50 µW for battery-powered designs. The serial interface is compatible with standard SPI/QSPI/MICROWIRE hosts, simplifying connection to microcontrollers and DSPs. Input protection diodes are absent on the analog input pin, so external clamping is required when the input can exceed the supply rails. Typical applications include industrial process control data acquisition, multichannel PLC analog input modules, portable instrumentation, weighing scales, and remote sensor digitizers. The combination of ±5 V true-bipolar input range and serial output makes the part especially well suited to legacy PLCs and 4-20 mA loop digitizers. Designers should observe the datasheet's reference decoupling and analog-input filtering guidelines to realize the rated INL/DNL and signal-to-noise ratio, and should add an external TVS/Schottky clamp at the analog input when transients beyond ±5 V are possible.
AD977ABRS - 16-Bit 200kSPS Serial I/O ADC | Analog Devices
The Analog Devices AD977ABRS is a 16-bit, 200 kSPS successive approximation register (SAR) analog-to-digital converter with a serial I/O interface, housed in a 28-pin SSOP package. Operating from a single 5 V supply, the AD977A variant delivers 200 kSPS throughput while its companion AD977 delivers 100 kSPS, both with 100 mW maximum power dissipation and a 50 µW power-down mode. An SAR ADC is a precision data converter that performs a binary search against the analog input using an internal capacitive DAC, sample-and-hold, reference, and clock. SAR ADCs occupy the precision-mid-tier in the converter hierarchy (SAR -> ADC -> data converter -> mixed-signal IC -> semiconductor), combining high DC accuracy, low latency, and a compact serial output - ideal for multiplexed data-acquisition systems. Key features of the AD977ABRS include unipolar input ranges of 0V to 5V and 0V to 4V plus bipolar ranges of ±5V and ±3.3V, providing measurement flexibility across industrial sensor signal levels. The device integrates a reference, clock, and sample-and-hold, and provides either an internal clock or an external data-clock-synchronized serial output. Maximum power dissipation is 100 mW active and 50 µW in shutdown mode. The AD977ABRS is fabricated on a BiCMOS process that pairs bipolar input buffers with CMOS logic, achieving low input-referred noise and stable DC linearity at the 200 kSPS conversion rate. The integrated 2.5 V reference and single-supply 5 V operation remove the need for external reference components in many applications. Typical applications include industrial process control, multi-channel data-acquisition systems, instrumentation, weigh scales, and portable battery-powered measurement equipment. The serial interface simplifies isolation barriers, while the small 28-SSOP footprint suits dense multi-channel layouts. When designing with this ADC, ensure the analog input is driven from a low-impedance source and referenced to AGND1 to avoid resistive ground-drop artifacts. Place the 2.5 V reference bypass and the input RC anti-alias filter within 1 mm of the input and reference pins. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the Analog Devices datasheet alone, enabling faster component selection and PCB layout decisions.
AD977ACR - 16-Bit 200 kSPS SAR ADC | Analog Devices
The Analog Devices AD977ACR is a 16-bit, 200 kSPS successive-approximation analog-to-digital converter operating from a single 5 V supply in a 20-pin SOIC package. It combines a switched-capacitor SAR conversion architecture with an internal 2.5 V reference and supports industrial-temperature applications requiring a precise, low-power conversion solution. An ADC is a mixed-signal integrated circuit that converts a continuously varying analog voltage into a numeric code for processing, measurement, or transmission. Within the semiconductor hierarchy, the AD977ACR is a data converter, specifically a SAR ADC and analog-to-digital converter. SAR converters compare the sampled input against an internal reference through a binary-search conversion process, making them well suited to instrumentation and control systems where power consumption and deterministic latency matter more than maximum sampling frequency. The verified device information identifies the AD977 family as a high-speed, low-power 16-bit converter with single 5 V operation. The AD977A member provides a 200 kSPS throughput rate, while the related AD977 reaches 100 kSPS. Other verified characteristics include BiCMOS construction, an internal 2.5 V reference, switched-capacitor conversion, one analog input, and an industrial temperature grade for the AD977ACR ordering code. The 20-lead gull-wing surface-mount package is identified as a rectangular SOP package by distributor listings. Its SAR architecture avoids the continuous internal sequencing demands of pipeline converters, helping limit power use while retaining 16-bit nominal resolution. Because the available web excerpts do not publish complete timing curves, input impedance, common-mode range, or full-scale accuracy tables, those parameters require confirmation in the Analog Devices AD977/AD977A technical documentation before a production design is released. Typical uses include industrial process-control instrumentation, digital measurement systems, data-acquisition modules, sensor interface equipment, and embedded test systems. The single 5 V supply simplifies analog and digital power planning, while the internal 2.5 V reference can reduce the external component count when the application's accuracy and reference-current requirements allow it. The principal design consideration is reference and layout discipline. Keep the analog input trace short, place decoupling capacitors close to the supply pins, and route high-current digital return currents away from the converter input. Confirm the source impedance, acquisition time, common-mode limits, and output-code behavior against the complete manufacturer datasheet rather than relying on marketplace summaries alone.
AD977AR - 16-Bit 100 kSPS Serial ADC | Analog Devices
The Analog Devices AD977AR is a 16-bit, 100 kSPS, single-input successive-approximation analog-to-digital converter operating from one 5 V supply and housed in a 20-pin SOIC package. The AD977 family uses a switched-capacitor ADC architecture with an internal 2.5 V reference and a high-speed serial interface. According to the Analog Devices product page, the AD977A reaches 200 kSPS while the AD977 reaches 100 kSPS. An ADC is an analog-to-digital converter, a semiconductor that samples a continuous analog voltage and produces a corresponding numeric code for digital processing. AD977AR belongs to the successive-approximation ADC family, a type commonly used where moderate sampling rate, low power, compact packaging, and straightforward system integration are more important than very high conversion bandwidth. Its 16-bit resolution supports finely quantized measurements while the single 5 V supply simplifies system power architecture. The verified features include a 16-bit conversion resolution, 100 kSPS throughput for AD977, and 200 kSPS throughput for AD977A. The device is factory calibrated, has unipolar and bipolar input-range options, supports 5 V and 3.3 V bipolar configurations as described in the retrieved datasheet material, and provides a power-down mode. Its switched-capacitor SAR architecture separates acquisition and conversion functions while retaining a compact, low-power implementation. The AD977AR is suitable for industrial measurement, instrumentation, process control, sensor acquisition, data acquisition systems, and embedded control platforms. A system designer should select the input range and reference arrangement required by the analog signal, then validate conversion timing against the 100 kSPS device rating. The serial interface reduces package pin count and board area, but the host processor must support the required clocking and data protocol. The main design consideration is analog signal conditioning. Keep the input within the selected unipolar or bipolar range, account for source impedance and sampling behavior, and provide stable reference and supply decoupling close to the device. For replacement decisions, the exact suffix, package, interface, input range, reference configuration, and timing must be checked rather than relying only on the AD977 family name. This page combines the verified AD977 family specifications with application guidance, pin-level caveats, comparison placeholders, and procurement-oriented information. It is intended to help engineers identify whether the AD977AR matches a 16-bit, 100 kSPS, single 5 V ADC design and to locate the manufacturer datasheet and distributor listings before committing to a board or production release.
AD977ARZ - 16-Bit 100 kSPS SAR ADC | Analog Devices
The Analog Devices AD977ARZ is a 16-bit, single-channel, successive-approximation analog-to-digital converter with a throughput rate of 100 kSPS, operated from a single 5 V supply and packaged in a 20-pin SOIC. The converter combines an internal 2.5 V reference, factory calibration, and a high-speed serial interface in a low-power analog-to-digital converter package. An ADC is an integrated circuit that converts an analog voltage into a digital code for processing, measurement, or control. The AD977 belongs to the successive-approximation, or SAR, ADC family, which successively compares the input voltage with an internally generated reference voltage. SAR ADCs are widely selected for precision measurement because they provide deterministic conversion behavior, compact implementation, and an effective balance of resolution, speed, and power consumption. The AD977ARZ provides 16-bit nominal resolution, one analog input, and a 100 kSPS conversion rate. It operates from a single 5 V supply, while an internal 2.5 V reference supplies the conversion reference. Its factory calibration is designed to minimize gain, offset, and nonlinearity errors, reducing the need for extensive calibration in the end system. Digital information is transferred through the high-speed serial interface rather than a parallel data bus, which keeps the package compact and reduces the number of PCB signal traces. The switched-capacitor SAR architecture supports low-power operation compared with many higher-speed flash and pipeline converters. The manufacturer documentation identifies low power dissipation as a core characteristic, with a 100 mW maximum value reported in the retrieved specification data. Power-down operation is also available for systems that need to reduce consumption when conversions are not continuously required. The usable analog supply range reported by the retrieved data is 4.75 V to 5.25 V. Typical uses include industrial process monitoring, sensor signal acquisition, instrumentation, communications equipment, data acquisition, and embedded control systems where a 16-bit conversion result and 100 kSPS throughput are sufficient. The serial interface is particularly useful when board space is constrained or the converter is connected to a microcontroller, programmable logic device, or dedicated digital controller. When designing around the AD977ARZ, preserve separate analog and digital ground return paths and reference the analog input to the AGND1 pin specified by Analog Devices. Drive the analog input from a low-impedance source, and verify the complete power, ground, decoupling, and serial-interface implementation against the manufacturer datasheet before production release. This page combines the verified manufacturer and distributor specifications, sourced pricing, package information, practical application guidance, and explicit data gaps. It is intended to help engineers evaluate the AD977ARZ for 16-bit, 100 kSPS single-supply acquisition without concealing information that remains unavailable in the retrieved source material.
AD977BN - 16-Bit 100 kSPS ADC | Analog Devices
The Analog Devices AD977BN is a 16-bit, single-channel, successive-approximation analog-to-digital converter with a 100 kSPS throughput rate, serial interface, and 20-pin PDIP package. It operates from a single 5 V supply and provides selectable unipolar and bipolar input ranges for precision signal acquisition. An ADC converts an analog voltage into a digital code for measurement, control, instrumentation, and signal-processing systems. The AD977 belongs to the successive-approximation ADC, or SAR ADC, family within the broader data-converter and mixed-signal semiconductor hierarchy. Its 16-bit resolution supports fine amplitude quantization, while its 100 kSPS throughput is suited to accurate acquisition of slowly changing or moderate-bandwidth signals. The verified product information identifies a 16-bit SAR architecture, one analog input, serial I/O, and operation from a single 5 V supply. Available input ranges include unipolar 0 V to 5 V and 0 V to 4 V, plus bipolar 0 V to 5 V and 0 V to 3.3 V. The AD977 family also offers an external-reference option, while the manufacturer describes the converter as a low-power, high-speed data-acquisition device. The AD977A is a related family member with a 200 kSPS throughput rate, whereas the AD977 used by AD977BN is specified at 100 kSPS. This distinction matters when selecting a replacement: a faster related device may require different timing, acquisition, and system-level validation even when its resolution and function are similar. Typical applications include industrial process measurement, laboratory data acquisition, instrumentation, transducer interfaces, and embedded control systems. The serial interface can reduce PCB routing requirements compared with a parallel ADC, but the host processor must read the serial data at the converter's supported rate and account for acquisition and conversion timing. For robust designs, provide a stable reference and supply, connect the analog input according to the selected input range, and validate signal-conditioning bandwidth against the 100 kSPS throughput. The 20-pin PDIP package is through-hole and is not a direct substitute for surface-mount implementations without a package and pinout review. This page combines the verified Analog Devices family description, distributor identification, package information, and practical selection guidance. It also distinguishes the AD977BN from the faster AD977A rather than presenting related family variants as interchangeable without qualification.
AD977BR - 16-Bit 100 kSPS Serial ADC | Analog Devices
The Analog Devices AD977BR is a 16-bit, 100 kSPS, single-input successive-approximation analog-to-digital converter operating from one 5 V supply in a 20-lead SOIC package. It uses serial I/O, provides unipolar and bipolar input ranges, and includes an internal 2.5 V reference according to the manufacturer product page. The converter combines a 16-bit sampling rate of 100,000 conversions per second with low-power operation and a 100 mW maximum specified power dissipation. An ADC is a data-acquisition semiconductor that converts an analog voltage into a digital code for measurement, control, instrumentation, and signal-processing systems. The AD977 belongs to the successive-approximation ADC family, also called a SAR ADC. Compared with flash and pipeline converters, a SAR ADC generally uses sequential internal comparisons, making this device suitable for moderate-speed precision acquisition where output resolution, serial communication, and low power are more important than very high conversion throughput. The AD977BR provides a 16-bit conversion result at 100 kSPS from a single 5 V supply. Its input architecture supports unipolar ranges of 0 V to 5 V and 0 V to 4 V, plus bipolar ranges of ±5 V and ±3.3 V. The verified sources also identify external-reference and power-down options, internal-reference capability, and industrial-temperature packaging. These features allow the same converter family to address sensor interfaces, process-control measurements, laboratory acquisition, and industrial diagnostic systems. The switched-capper architecture is factory calibrated, as stated in the Analog Devices datasheet description. Sampling and conversion behavior must be coordinated with the serial interface and external analog network. The AD977BR uses serial I/O rather than a parallel data bus, reducing package pin count and PCB routing requirements while requiring compatible firmware or control logic. The AD977A member provides a higher 200 kSPS rate, whereas the AD977BR is the 100 kSPS version. Typical applications include industrial process monitoring, sensor signal acquisition, medical instrumentation, laboratory measurement, communications equipment, and embedded data-acquisition systems. A system designer should verify the exact input range, reference configuration, timing, electrical limits, and pin-level requirements against the manufacturer datasheet before layout or firmware release. The most important design consideration is preserving analog signal integrity while supporting the serial interface. Keep the analog input and reference paths short, use suitable bypass and filtering components, and account for source impedance during acquisition. The verified data does not provide all timing, accuracy, temperature, and reference-load details, so those values should be obtained from the official AD977/AD977A datasheet. This page consolidates the verified manufacturer and distributor information, separates confirmed AD977BR characteristics from unknown parameters, and provides application guidance without treating unverified values as specifications.
AD977BRZ - 16-Bit 100 kSPS SAR ADC | Analog Devices
The Analog Devices AD977BRZ is a 16-bit successive-approximation analog-to-digital converter with one analog input, a 100 kSPS throughput rate, a single 5 V supply, and a 20-pin SOIC package. The device also provides an internal 2.5 V reference and a high-speed serial interface, making it suitable for precision signal acquisition when both resolution and compact implementation are important. Factory calibration is used by the manufacturer to minimize linearity error. An ADC is an interface component that converts a continuously varying analog voltage into a numeric value for processing, measurement, display, or control. The AD977 belongs to the successive-approximation, or SAR, ADC family. SAR converters compare the input against successive trial values, making this architecture suitable for medium-speed data acquisition, industrial measurement, communication equipment, and embedded instrumentation. Within the broader hierarchy, the AD977 is an ADC, then a data-conversion IC, and finally a semiconductor or analog-to-digital converter. The AD977BRZ provides a 16-bit conversion result, 100 kSPS throughput, and operation from one 5 V supply. Its internal 2.5 V reference reduces the external component count, while the serial interface supports compact board layouts. The 20-pin SOIC package uses surface-mount assembly and is available from distributors including DigiKey, Mouser, LCSC, Win Source, and Octopart. Technically, the converter uses a switched-capacitor successive-approximation architecture. The internal reference establishes the conversion scale, and the factory calibration is intended to improve offset and linearity performance. Because this is a medium-speed SAR converter rather than a flash or pipeline ADC, it provides a practical balance among throughput, resolution, power consumption, and implementation complexity for precision acquisition systems. Typical uses include precision process measurement, laboratory and test instrumentation, communications equipment, and embedded control systems. The 100 kSPS rate permits acquisition of relatively slow or medium-bandwidth signals, while the 16-bit resolution preserves fine amplitude detail. The serial interface can also reduce the number of parallel data paths when board space is constrained. Designers should verify the analog input range, acquisition timing, reference behavior, and serial-interface timing against the manufacturer datasheet before finalizing signal-chain calculations. Input buffering, source impedance, sampling-capacitor settling, digital grounding, and decoupling remain important even though the converter integrates reference and conversion circuitry. This product record combines verified manufacturer and distributor data with an honest drop-in assessment. It distinguishes the electrically compatible AD977CR option from broader functional substitutes, documents unavailable pricing and pinout details, and highlights the practical design information needed to choose and implement a 16-bit SAR ADC without treating similar converters as automatic PCB replacements.
AD977CN - 16-Bit 100 kSPS ADC | Analog Devices
The Analog Devices AD977CN is a 16-bit, 100 kSPS successive-approximation analog-to-digital converter in a 20-pin through-hole DIP package. It operates from a single 5 V supply, supports unipolar and bipolar input ranges, and is designed for precision signal acquisition where 16-bit resolution is useful without the throughput demands of a flash converter. The AD977 family also includes the faster AD977A, which is specified at 200 kSPS. An ADC is a data-acquisition IC that converts an analog voltage into a digital code. A successive-approximation ADC, commonly called a SAR ADC, performs conversion by comparing the unknown input with an internally generated trial voltage and progressively refining a binary approximation. The AD977CN therefore belongs to the ADC, data-converter, signal-processing, and semiconductor hierarchy, with relevance to industrial measurement, instrumentation, communications, and embedded control systems. The converter provides a 16-bit resolution, a 100 kSPS throughput rate, and single 5 V operation. Its input architecture includes unipolar ranges of 5 V and 4 V and bipolar ranges of 5 V and 3.3 V, according to the verified manufacturer product information. Available interface choices and power-management behavior should be confirmed in the manufacturer datasheet for the exact AD977CN ordering configuration. Maximum power dissipation is listed as 100 mW in the supplied verified description, while a power-down mode is also indicated. Because this is a SAR ADC, the input is sampled and converted through a sequence of internal comparison decisions rather than a parallel flash architecture. This makes the converter suitable for control loops, sensor interfaces, test equipment, and communication front ends that need moderate speed and high resolution. The AD977CN is a 100 kSPS device, whereas AD977A is the 200 kSPS family variant; selecting the correct suffix is important when sample rate is a hard system constraint. AD977CN applications include industrial process monitoring, precision instrumentation, communications receivers, data-acquisition cards, and embedded measurement systems. In each case, the analog front end must establish the correct input range, provide suitable reference and drive circuitry, and account for acquisition time before conversion. The serial or parallel data interface and required digital support components should be selected from the datasheet and system clock plan. A key design consideration is the input and reference network. Incorrect source impedance, inadequate filtering, or unsuitable bypass capacitance can degrade effective resolution and conversion accuracy. The 5 V supply should be decoupled close to the device, and the analog input should be protected against overvoltage and transients. Because the AD977CN is listed as obsolete in one verified distributor-style source, new designs should confirm lifecycle status, availability, and any supported migration path before committing to production. This page consolidates the verified Analog Devices family description, distributor identity, package information, and practical replacement guidance for AD977CN. It also distinguishes confirmed facts from parameters that require the exact manufacturer datasheet, helping engineers evaluate the obsolete 16-bit SAR ADC without treating unverified electrical values as production specifications.
AD977CNZ - 16-Bit 100 kSPS SAR ADC | Analog Devices
The Analog Devices AD977CNZ is a 16-bit, single-input successive-approximation analog-to-digital converter with a 100 kSPS throughput rate, operating from a single 5 V supply and housed in a 20-pin plastic DIP package. It combines a factory-calibrated switched-capacitor conversion core, an internal 2.5 V reference, and a high-speed serial interface for precision signal-acquisition systems. An ADC converts an analog input voltage into a digital code for measurement, control, recording, or signal processing. The AD977 belongs to the successive-approximation ADC family within the broader ADC/DAC and data-converter hierarchy. Its SAR architecture repeatedly compares the sampled input with a internally generated reference, making it suitable for applications requiring accurate conversion without the complexity of flash conversion. Key specifications include 16-bit resolution, one analog input, a 100 kSPS sampling rate, and operation from a single 5 V rail. Maximum power dissipation is 100 mW, supporting low-power acquisition systems. The supported operating-temperature range is -40°C to 85°C, while the 20-PDIP package is supplied in a tube for through-hole PCB assembly. Internally, the AD977 combines a switched-capacitor ADC, a 2.5 V internal reference, and a high-speed serial interface. Factory calibration minimizes offset, gain, and linearity errors, while listed AC testing includes signal-to-noise ratio and total harmonic distortion performance. The AD977 family provides 100 kSPS throughput, whereas the related AD977A family provides 200 kSPS. Typical uses include industrial process measurement, instrumentation, laboratory data acquisition, audio and low-frequency waveform sampling, sensor-interface systems, and embedded control platforms. The 100 kSPS rate is appropriate for acquiring slowly changing or moderate-bandwidth analog signals rather than high-frequency communications waveforms. Designers should provide a stable 5 V supply, observe the analog and reference grounding requirements, and validate input range and acquisition timing against the manufacturer datasheet. Because the serial interface, reference behavior, conversion timing, and digital signaling remain important to system accuracy, firmware and PCB validation should be completed before production release. This product page consolidates verified manufacturer and distributor specifications, package details, availability references, and selection guidance. It also distinguishes the AD977CNZ from the faster AD977A family and clearly identifies where equivalent drop-in replacement data was not established by the supplied cross-reference evidence.
AD977CRZ - 16-Bit 100 kSPS SAR ADC | Analog Devices
Analog Devices AD977CRZ is a 16-bit successive-approximation analog-to-digital converter with a 100 kSPS throughput rate, operated from a single 5 V supply and housed in a 20-pin SOIC package. The converter combines a 16-bit sampling ADC, an internal reference, and a serial SPI-compatible interface in one low-power IC. An ADC is a data-acquisition IC that converts an analog voltage into a digital number for processing by a microcontroller, DSP, FPGA, or industrial controller. The AD977 belongs to the SAR ADC category, where a successive-approximation internal DAC drives a comparator until the converted result matches the analog input. SAR converters are useful when moderate conversion speed, low power, and simple serial connectivity are more important than maximum sampling throughput. Key features include 16-bit resolution, a 100 kSPS conversion rate, and operation from one 5 V supply. The verified data also identifies a maximum power dissipation of 100 mW, a power-down mode, and a serial SPI data interface. These characteristics make the AD977CRZ suitable for industrial instrumentation, process-control acquisition, data loggers, and embedded measurement systems where sampled bandwidth is measured in hundreds of hertz to tens of kilohertz. The device uses a successive-approximation conversion architecture rather than a flash, pipeline, or sigma-delta architecture. Each conversion requires repeated comparison of the input against an internally generated approximation. This architecture supports a relatively straightforward serial interface and low power dissipation, while the 16-bit word length provides substantially more code levels than an 8-bit converter. The single 5 V supply also simplifies analog and digital system integration when the selected interface and reference arrangement remain compatible. Typical uses include programmable laboratory instruments, temperature and pressure acquisition chains, factory-control modules, battery-powered field recorders, and embedded condition-monitoring equipment. In these systems, the ADC can be paired with sensors and instrumentation amplifiers, while its serial interface connects directly to a low-speed microcontroller or embedded control system. A key design consideration is that analog-input conditioning, reference quality, grounding, and digital-interface timing can be as important as the nominal converter resolution. Designers should follow the Analog Devices AD977 product page and datasheet for the complete electrical characteristics, pin functions, acquisition timing, and recommended application circuit rather than inferring missing details from distributor summaries. This page consolidates the verified manufacturer and distributor information, separates documented facts from unavailable data, and adds practical selection guidance that is not normally presented together on a distributor listing.
AD9833BRUZ-REEL7 - 25MHz DDS Waveform Generator | Analog Devices
The AD9833BRUZ-REEL7 is a low power, programmable waveform generator from Analog Devices that produces sine, triangular, and square wave outputs. It operates from a 2.3 V to 5.5 V supply and consumes only 12.65 mW at 3 V, making it ideal for battery-powered and portable applications. The device features a 28-bit frequency register, allowing fine frequency resolution of 0.1 Hz at 25 MHz clock, and a 10-bit DAC for amplitude control. It communicates via a 3-wire SPI interface, simplifying integration with microcontrollers and DSPs. A Direct Digital Synthesis (DDS) IC is a type of waveform generator that uses digital signal processing to synthesize analog waveforms from a fixed-frequency reference clock. It is a key component in frequency synthesis, modulation, and signal generation systems. DDS devices are part of the broader category of data converters and signal generation ICs, which are essential in test equipment, communication systems, and medical devices. Key features include a 25 MHz maximum clock frequency, 28-bit frequency resolution, and a 10-bit DAC. The AD9833 supports multiple output waveforms, including sine, triangular, and square waves, and can be programmed to output a constant level or a modulated signal. The device also includes a power-down mode that reduces current consumption to 0.5 µA, extending battery life in portable applications. The AD9833 uses a phase accumulator architecture to generate waveforms with high accuracy and stability. The phase accumulator increments by a frequency tuning word (FTW) each clock cycle, and the output is read from a lookup table. This architecture allows for fast frequency hopping and precise phase control, making it suitable for applications such as frequency-shift keying (FSK) and phase-shift keying (PSK) modulation. Typical applications include function generators, frequency synthesizers, impedance spectroscopy, and time domain reflectometry (TDR). The device is also used in audio and vibration testing, where precise frequency control is required. Its low power consumption and small package make it suitable for portable and handheld instruments. When designing with the AD9833, ensure that the SPI interface is properly configured and that the reference clock is stable and accurate. The output amplitude is set by the full-scale current of the DAC, which can be adjusted with an external resistor. Proper decoupling of the power supply and careful PCB layout are essential to minimize noise and jitter.
AD9873JS - 232 MHz Mixed-Signal AFE | Analog Devices
The Analog Devices AD9873JS is a mixed-signal analog front-end converter with a complete 232 MHz quadrature digital transmitter, a 12-bit ADC, a 10-bit ADC, two 8-bit ADCs, and two sigma-delta control DACs, supplied in a 100-lead MQFP package. The device is designed for broadband communications, including cable set-top boxes, cable modems, and related video and digital-data systems. A mixed-signal analog front-end, or AFE, combines analog signal acquisition and conversion functions with digital processing and interface functions on one integrated circuit. In the AD9873JS, this integration includes multiple ADC channels and a quadrature digital up-converter, allowing a system to receive and transmit broadband signals while limiting external component count. Its architecture is positioned for cost-sensitive broadband equipment where size, power dissipation, and dynamic performance are important. The verified manufacturer material identifies a 232 MHz quadrature digital transmitter, output bandwidth up to 65 MHz, and a 12-bit TxDAC+ direct IF digital-to-analog converter. The receive section includes four ADCs with different resolutions: one 12-bit ADC, one 10-bit ADC, and two 8-bit ADCs. Two sigma-delta control DACs support control functions within the mixed-signal signal chain. The AD9873JS is identified as a 3.3 V CMOS analog front-end converter for MCNS-DOCSIS, DVB, and DAVIC-compliant set-top-box and cable-modem applications. The AD9873JS combines a transmit path and multichannel receive path in one device, reducing the number of separate conversion and modulation blocks required by a broadband front end. The 232 MHz transmitter section is intended for quadrature digital signal generation, while the multichannel ADC section supports video and digital-data reception. This makes the device relevant to cable-modem headends, set-top-box receiver designs, DVB systems, and other broadband communication equipment requiring multiple conversion functions. Typical implementation requires careful attention to analog input conditioning, clocking, digital data timing, power distribution, and PCB layout. Because the device integrates several high-speed and precision functions, decoupling and controlled return paths are essential for minimizing noise and crosstalk. The external interface and pin arrangement should be verified against the complete Analog Devices datasheet before PCB release, especially when matching the AD9873JS variant and its 100-lead MQFP footprint. This page consolidates the verified AD9873JS product description, package identification, conversion features, application positioning, sourcing references, and design-oriented guidance. It also records where detailed electrical limits, timing values, pricing, pin assignments, and lifecycle information were not present in the supplied verified data, rather than inferring them.
ADADC85S-12/883B - 12-Bit SAR ADC, MIL-STD-883 | Analog Devices
The Analog Devices ADADC85S-12/883B is a 12-bit successive-approximation analog-to-digital converter (SAR ADC) qualified to MIL-STD-883 Class B, integrating a precision reference, internal clock, and comparator into a single 32-pin SBCDIP (Side-Brazed Ceramic DIP) hybrid package. The ADADC85S-12/883B provides 12-bit parallel output data and is designed for high-reliability military, aerospace, and industrial applications requiring a fully complete, hermetic ADC module. A successive-approximation ADC is a converter topology that uses an internal binary search algorithm, comparing the input voltage against a precision reference once per bit per clock cycle. Compared to flash ADCs (which use 2^N parallel comparators), SAR ADCs deliver higher resolution at lower power with no pipeline latency, making them well suited to multiplexed data acquisition systems, instrumentation, and process control loops where the ADC must settle to full resolution before the next channel is selected. Key features of the ADADC85S-12/883B include monolithic 12-bit feedback DAC architecture, internal buried-zener reference, and internal clock oscillator. The hybrid IC design combines MSI digital and linear monolithic chips with a 12-bit monolithic DAC to deliver modular performance and reliability in a single hermetic package. The device is processed to MIL-STD-883, Class B requirements, making it suitable for high-reliability military and aerospace systems. Operating from ±15 V and +5 V supplies, the part includes three-state output buffers for direct interface to microprocessor data buses. The ADADC85S-12/883B uses a hybrid construction that mounts a 12-bit monolithic feedback DAC, MSI digital logic, and precision linear circuitry on a single ceramic substrate, then hermetically seals the assembly in a 32-pin side-brazed ceramic DIP. The buried-zener reference (rather than a bandgap) yields low temperature drift and low noise, key for instrumentation and process-control front ends. Typical applications include military and aerospace data acquisition systems, process control front ends, precision instrumentation, military radar systems, and avionics sensor read-out. The wide supply range (±15 V analog, +5 V digital) simplifies power-tree design in retro and new-build avionics. A key design tip when laying out a board for the ADADC85S-12/883B: keep analog and digital grounds separated and join them only at the ADC ground pin, because the hybrid module has long internal bond wires and the high-speed digital output transitions can couple into the analog reference if grounds are not managed carefully. This page synthesizes distributor pricing, MIL-STD-883B screening information, drop-in alternatives, and comparison data not consolidated in any single manufacturer or distributor source.
ADADC85S12/883B - 12-Bit SAR ADC, 10us | Analog Devices
The ADADC85S12/883B is a high-speed, low-cost 12-bit successive approximation analog-to-digital converter (ADC) from Analog Devices, featuring an internal clock, reference, and comparator. It is packaged in a 32-pin SBDIP (Side-Brazed Dual Inline Package) and is designed for military and aerospace applications, meeting MIL-STD-883 Class B screening requirements. The device offers a conversion time of 10 microseconds and operates over the full military temperature range of -55°C to +125°C. An analog-to-digital converter (ADC) is a critical component in electronic systems that converts continuous analog signals into discrete digital values for processing by digital circuits. The ADADC85S12/883B is a successive approximation register (SAR) ADC, which uses a binary search algorithm to determine the digital output. SAR ADCs are known for their high speed and moderate resolution, making them suitable for applications such as data acquisition, industrial control, and military instrumentation. The ADADC85S12/883B integrates the clock, reference, and comparator on-chip, reducing external component count and simplifying design. Key features of the ADADC85S12/883B include 12-bit resolution, a 10-microsecond conversion time, and an internal reference and clock. The device operates from a single +5V supply and provides parallel output data. The MIL-STD-883 Class B screening ensures high reliability for defense and aerospace applications. The SBDIP package offers excellent thermal performance and is suitable for through-hole mounting. The ADADC85S12/883B uses a hybrid IC design that combines MSI digital and linear monolithic chips with a 12-bit monolithic DAC. This architecture provides modular performance and versatility while maintaining a compact size and low cost. The internal comparator and reference are trimmed for accuracy, ensuring consistent performance across the operating temperature range. Typical applications include military avionics, radar systems, missile guidance, and high-reliability industrial data acquisition. The device's wide temperature range and MIL-STD-883 qualification make it ideal for harsh environments. When designing with this ADC, ensure proper decoupling on the power supply and reference pins to minimize noise and achieve specified performance.
ADAQ4001BBCZ - 16-Bit 2MSPS μModule DAQ | Analog Devices
The ADAQ4001BBCZ from Analog Devices is a 16-bit, 2 MSPS μModule data acquisition system (DAS) that integrates a complete signal chain into a compact 49-ball CSPBGA (7x7 mm) package. This μModule solution includes a low-noise, high-bandwidth ADC driver, a precision reference buffer, and a 16-bit successive approximation register (SAR) ADC, eliminating the need for external signal conditioning components and simplifying design. The device operates from a single 5V supply and supports a reference voltage range of 2.4V to 5.1V, with an input common-mode voltage range of 0V to +VS - 1.5V. It features a serial peripheral interface (SPI)-compatible serial interface that is compatible with 1.8V, 2.5V, 3V, or 5V logic via a separate VIO supply, and is specified for operation from -40°C to +125°C. A data acquisition system (DAS) is a complete signal chain solution that converts analog signals into digital data for processing. The ADAQ4001 integrates the analog front-end (AFE), ADC, and reference buffer into a single module, reducing board space and design complexity compared to discrete implementations. This μModule approach is part of the broader category of data acquisition ICs, which are essential in applications such as industrial process control, medical instrumentation, and test and measurement equipment. Key features of the ADAQ4001BBCZ include its 16-bit resolution and 2 MSPS sampling rate, which enable high-speed, high-precision data conversion. The integrated reference buffer allows the use of external references from 2.4V to 5.1V, providing flexibility in system design. The SPI-compatible interface supports multiple logic levels, making it easy to interface with various microcontrollers and FPGAs. The device also features a low-power mode, reducing power consumption in battery-powered applications. Technically, the ADAQ4001 uses a SAR architecture, which offers excellent linearity and low latency. The integrated ADC driver is optimized for driving the SAR ADC's switched-capacitor input, ensuring accurate conversion even at high sampling rates. The reference buffer provides a low-impedance drive to the ADC's reference input, maintaining stable performance over temperature and supply variations. The device is available in a 49-ball CSPBGA package, which offers excellent thermal performance and a small footprint. Typical applications for the ADAQ4001BBCZ include industrial process control, where it can be used for precise monitoring of sensors and actuators; medical instrumentation, such as patient monitoring and diagnostic equipment; and test and measurement systems, where high-speed, high-resolution data acquisition is critical. The device's wide operating temperature range and robust design make it suitable for harsh environments. When designing with the ADAQ4001BBCZ, it is important to ensure that the reference voltage is selected appropriately for the system's input range, and that the input common-mode voltage remains within the specified limits. Proper decoupling of the power supply and reference pins is essential for achieving optimal performance.
ADAQ4216BCPZ - 16-Bit 2MSPS μModule DAQ | Analog Devices
The ADAQ4216BCPZ is a μModule® precision data-acquisition (DAQ) signal chain solution from Analog Devices that integrates a 16-bit successive approximation register (SAR) analog-to-digital converter (ADC), a low-noise, low-distortion ADC driver, and a 1.8V low dropout (LDO) regulator into a single 178-ball BGA package. This integration reduces the development cycle of precision measurement systems by transferring the signal-chain design challenge of component selection, optimization, and layout from the designer to the device. With a guaranteed maximum ±3ppm INL and no missing codes at 16 bits, the ADAQ4216 achieves unparalleled accuracy for high-resolution measurement applications. A data acquisition system (DAQ) is a device that samples real-world analog signals and converts them to digital values for processing. The ADAQ4216 is a complete signal chain solution, meaning it includes the ADC, driver amplifier, and power regulation in one package, simplifying design and improving performance by minimizing parasitic effects. This μModule approach is part of the broader category of integrated signal chain solutions, which are essential in precision instrumentation, industrial control, and medical devices. Key features of the ADAQ4216 include a 16-bit resolution with a maximum sample rate of 2 MSPS, a SPI interface for digital communication, and an input range of -8V to +10V. The device operates from a 5V analog supply and a 1.8V digital supply, with a typical power dissipation of [DATA_NEEDED: power dissipation]. The integrated LDO provides a clean 1.8V supply for the ADC core, reducing external component count and improving noise performance. The ADAQ4216 uses a SAR architecture with auto-zeroing to cancel 1/f noise, resulting in a noise spectral density that is substantially uniform from DC to fS/2. This makes it ideal for applications requiring high accuracy and low noise, such as automated test equipment, industrial process control, and medical imaging. The device is specified over the industrial temperature range of -40°C to +85°C and is available in a 178-ball BGA package (14x9 mm). Typical applications include precision data acquisition systems, vibration analysis, and power quality monitoring. The integrated signal chain reduces board space and design time, making it suitable for space-constrained designs. When designing with the ADAQ4216, ensure proper decoupling of the power supplies and a clean ground plane to achieve the specified performance. The SPI interface allows easy connection to microcontrollers or FPGAs for data processing.
ADAQ4224BCPZ - 24-Bit 2MSPS μModule DAQ | Analog Devices
The Analog Devices ADAQ4224BCPZ is a μModule® precision data acquisition (DAQ) signal chain solution that integrates a complete signal chain into a single package, reducing the development cycle of precision measurement systems by transferring the design challenge of component selection, optimization, and layout from the designer to the device. It features a 24-bit, 2 MSPS ADC with guaranteed maximum ±1.0 ppm INL and no missing codes at 24 bits, achieving unparalleled accuracy for high-precision applications. A μModule is a complete system-in-package (SiP) that integrates multiple components—such as the ADC, reference, driver amplifier, and passive components—into a single package, simplifying design and reducing board space. The ADAQ4224 belongs to the precision data acquisition signal chain family, which is essential for applications requiring high resolution and accuracy, such as industrial process control, medical instrumentation, and scientific analysis. Key features include a 24-bit resolution, 2 MSPS sample rate, ±1.0 ppm INL, and a 178-BGA (14x9) package. The device supports both I2C and SPI digital interfaces, providing flexibility for various microcontroller and FPGA connections. The integrated signal chain ensures optimal performance by minimizing parasitic effects and layout-induced errors. The ADAQ4224 utilizes a precision ADC core with an integrated low-noise driver and reference, achieving high accuracy without external components. The μModule architecture reduces the need for external component selection and layout optimization, making it ideal for space-constrained designs. The device operates over a wide temperature range, ensuring reliable performance in demanding environments. Typical applications include industrial process control, medical instrumentation, scientific analysis, and automated test equipment. The high resolution and accuracy make it suitable for precision measurement systems where data integrity is critical. When designing with the ADAQ4224, ensure proper power supply decoupling and layout to maintain the high accuracy. The integrated signal chain simplifies design, but attention to grounding and thermal management is essential for optimal performance.
ADAQ4381-4BCPZ - Quad 14-Bit μModule DAQ | Analog Devices
The Analog Devices ADAQ4381-4BCPZ is a quad-channel, 14-bit data acquisition system (DAS) μModule that integrates multiple signal processing and conditioning blocks into a single 81-pin CSPBGA (8x8 mm) package. It combines a low noise, fully differential analog-to-digital converter (ADC), ADC drivers, a high precision 3.3 V reference chip, and a low-noise reference buffer, reducing end-system component count and design complexity. The device supports serial SPI interface and is compatible with 1.8 V, 2.5 V, and 3.3 V logic supplies via a separate logic supply pin. It is specified to operate over a temperature range of −40°C to +105°C. A data acquisition system (DAS) is a complete signal chain that samples analog signals, converts them to digital, and interfaces with a host processor. The ADAQ4381-4 is a μModule, a system-in-package that integrates the ADC, drivers, reference, and buffer, simplifying design and improving performance. It belongs to the hierarchy: μModule DAQ -> data acquisition system -> signal chain -> analog front end -> electronic system. Key features include 14-bit resolution, 4 MSPS sampling rate per channel, quad-channel simultaneous sampling, and a high precision 3.3 V reference. The integrated reference buffer ensures low noise and high accuracy. The device operates from a single 5 V analog supply and a separate logic supply, enabling flexible interface levels. The CSPBGA package offers excellent thermal and electrical performance, with a compact footprint for space-constrained designs. Technically, the ADAQ4381-4 uses a fully differential ADC architecture with integrated drivers, providing high input impedance and reduced external component requirements. The precision reference and buffer maintain low drift and high accuracy over temperature. The SPI interface allows easy configuration and data readout, with support for multiple devices on a single bus. The device includes power-down modes for low-power operation. Typical applications include industrial process control, automated test equipment, medical instrumentation, and multi-channel data logging. The quad-channel architecture is ideal for systems requiring simultaneous sampling of multiple signals, such as three-phase power monitoring or vibration analysis. The integrated reference and drivers reduce BOM cost and board space. When designing with this device, ensure proper decoupling of the analog and digital supplies, and use a clean ground plane to minimize noise. The SPI interface should be routed with controlled impedance to avoid signal integrity issues. The device requires an external clock or master clock input for conversion timing.
ADAQ7769-1BCPZ - 24-Bit 1MSPS μModule DAQ | Analog Devices
The Analog Devices ADAQ7769-1BCPZ is a 24-bit precision data acquisition (DAQ) μModule system that integrates signal conditioning, conversion, and processing blocks into a single system-in-package (SiP) design. This highly compact solution enables rapid development of high-performance precision DAQ systems. The device features a high input impedance, programmable gain amplifier (PGA), and an alias-free digital filter, making it ideal for applications requiring accurate measurement of dynamic signals. With a maximum sample rate of 1 MSPS and a 24-bit resolution, the ADAQ7769-1 delivers exceptional performance for industrial, instrumentation, and test and measurement applications. A data acquisition system (DAQ) is a device that samples analog signals and converts them to digital data for processing. The ADAQ7769-1 is a μModule (micro-module) DAQ, which means it encapsulates multiple functions—such as the input buffer, PGA, ADC, and reference—into one package. This integration simplifies design, reduces board space, and improves performance by minimizing parasitic effects. The μModule approach is part of a broader hierarchy: DAQ system → μModule → signal chain → analog-to-digital converter (ADC) → semiconductor. By integrating the entire signal chain, the ADAQ7769-1 reduces the need for external components and simplifies the design process. Key features of the ADAQ7769-1 include a high input impedance of 1 GΩ, a programmable gain of 0.1 to 64, and an alias-free digital filter that eliminates the need for external anti-aliasing filters. The device also supports a wide input voltage range of ±24 V, making it suitable for high-voltage sensing applications. The integrated reference buffer provides a low-noise, high-impedance reference input, ensuring accurate conversions. The device operates from a single 5 V supply and features a flexible SPI interface for configuration and data transfer. Technically, the ADAQ7769-1 uses a delta-sigma (ΔΣ) ADC architecture with a digital filter that provides alias-free operation. The device includes a precharge reference buffer and a full reference buffer, allowing the user to choose between ease of driving and high impedance. The device supports two configuration methods: register writes via SPI or hardware pin strapping for predefined modes. This flexibility simplifies integration into various systems. The device is specified for operation over the industrial temperature range of -40°C to +105°C. Typical applications include vibration monitoring, motor control, power quality analysis, and precision instrumentation. The high input impedance and programmable gain make it ideal for interfacing directly with sensors such as accelerometers and strain gauges. The alias-free operation ensures accurate measurement of high-frequency signals without the need for external filters. When designing with the ADAQ7769-1, it is important to provide a clean, low-noise power supply and a stable reference voltage. The device's integrated reference buffer simplifies reference driving, but external decoupling capacitors are recommended for optimal performance. Additionally, the SPI interface should be properly terminated to avoid signal integrity issues.
ADAU1978WBCPZ - Quad 24-bit ADC, 192kHz, AEC-Q100 | ADI
The Analog Devices ADAU1978WBCPZ is a high-performance quad analog-to-digital converter (ADC) with 24-bit resolution and up to 192 kHz sample rate, housed in a 40-pin LFCSP-WQ (6x6 mm) package with automotive AEC-Q100 qualification. It integrates four sigma-delta (Σ-Δ) ADC channels with 2 V rms AC-coupled inputs and a continuous-time front end engineered for low electromagnetic interference (EMI) susceptibility. According to the Analog Devices ADAU1978 datasheet, the device supports I2C and SPI control ports for volume, mute, and configuration via an external microcontroller. Per the ADI product page, the 1ku list price starts from $3.95. The ADAU1978 family uses only a single 3.3 V supply and integrates digital volume control with an autoramp function for clickless transitions. A sigma-delta ADC is a type of analog-to-digital converter that oversamples the input signal at a rate far above Nyquist and uses noise shaping to push quantization noise out of the audio band, trading sample rate for very high resolution. In the broader taxonomy, the ADAU1978 sits as an audio ADC -> ADC -> data converter -> mixed-signal IC -> semiconductor. The continuous-time input front end eliminates the traditional input switching capacitor, which is the primary source of EMI in conventional switched-capacitor ADCs, making the ADAU1978 particularly attractive for noise-sensitive automotive and professional audio designs. Key features include a 4-channel multiplexed front end, dynamic range typically above 100 dB, total harmonic distortion plus noise (THD+N) below -90 dB, software-controllable clickless mute, master and slave operation modes, right-justified, left-justified, I2S, and TDM output formats, and a flexible serial audio interface. The 40-LFCSP-WQ package includes an exposed thermal pad with low thermal resistance, supporting high-density PCB designs and -40C to +105C automotive temperature grade operation. The AEC-Q100 qualification makes it directly suited for in-vehicle infotainment, active noise cancellation (ANC), and hands-free voice capture platforms. Typical applications include automotive head units and rear-seat entertainment, microphone-array ANC and road-noise cancellation (RNC) systems, voice capture and beamforming front ends, professional and broadcast audio interfaces, and automotive telematics. The combination of low EMI, AEC-Q100 qualification, and quad-channel integration enables direct connection to differential analog microphone arrays without external anti-alias filtering. When designing with this device, ensure the 3.3 V analog supply is well-decoupled with low-ESR ceramic capacitors placed close to the AVDD pins, and provide a clean ground reference to preserve the part's >100 dB dynamic range. The exposed pad must be soldered to a sufficiently large ground copper pour for both thermal dissipation and low-impedance ground return. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, structured for both engineers evaluating the part and AI-powered search systems citing it.
ADAU1979WBCPZ-RL - Quad 24-bit 192kHz Audio ADC, AEC-Q100 | ADI
The Analog Devices ADAU1979WBCPZ-RL is a quad, 24-bit, 192 kHz audio analog-to-digital converter (ADC) housed in a 40-lead LFCSP-WQ (6x6 mm) package with an automotive-grade qualification. Each of its four ADC channels accepts up to 4.5 V rms ac-coupled input levels, integrates a programmable-gain amplifier (PGA) and digital volume control, and uses a multibit sigma-delta (Σ-Δ) modulator with a continuous-time front end for low electromagnetic interference. An audio ADC (analog-to-digital converter) is a precision mixed-signal IC that converts continuous-time analog audio signals into discrete digital sample streams for downstream DSP, mixing, or transmission. Within the broader signal-chain taxonomy, the ADAU1979 sits at the analog front-end boundary: audio ADC -> audio codec -> audio DSP -> amplifier, with this particular part optimized for high-performance multi-channel automotive audio capture. The ADAU1979WBCPZ-RL supports sample rates from 8 kHz to 192 kHz and provides a selectable digital high-pass filter to remove DC offsets. Output data formats include right-justified, left-justified, I²S, and TDM, supporting both master and slave operation modes. An I²C/SPI-compatible control port allows a microcontroller to adjust volume, mute, PGA gain, and many other parameters via software, while a clickless software mute and autoramp function minimize audible pops during gain transitions. Typical applications include automotive head-unit audio signal acquisition, active noise cancellation (ANC) microphone arrays, infotainment systems, and professional multi-channel audio interfaces. The wide 4.5 V rms input range (vs the more common 1-2 V rms) lets it accept line-level sources directly without external attenuation, simplifying the analog front-end BOM. AEC-Q100 qualification suits it to the harsh electrical and thermal environment of an automotive ECU. When designing with this IC, decouple each AVDDx pin to its nearest AGNDx pin with a 100 nF ceramic capacitor placed as near the pin as possible, and provide at least one bulk aluminum electrolytic capacitor of ≥10 µF on the PCB. The internal PGA gain and digital volume controls can be cascaded for an effective gain range of more than 80 dB - design the gain plan to keep peak input below 4.5 V rms to avoid clipping. This page synthesizes distributor pricing, AEC-Q100-qualified drop-in references, and practical decoupling guidance not consolidated in the manufacturer datasheet, giving engineers a single source of comparison.
ADC0801S040TS/C1 - 8-bit 40MSPS SAR ADC | NXP/Renesas
The NXP/Renesas ADC0801S040TS/C1 is an 8-bit universal analog-to-digital converter (ADC) for video and general-purpose applications, sampling at up to 40 MSPS in a 20-pin SSOP (LSSOP) package. It converts an analog input signal from 2.7 V to 5.5 V into 8-bit binary-coded digital words through a successive-approximation (SAR) architecture with a single analog input channel and a parallel CMOS/TTL-compatible digital interface. An SAR ADC (Successive Approximation Register Analog-to-Digital Converter) is a type of data converter that uses a binary search algorithm and an internal DAC to resolve each analog sample to its final digital code in N clock cycles, where N is the resolution in bits. SAR ADCs are valued for their deterministic latency, low power consumption, and the absence of pipeline delay, making them ideal for multiplexed control loops, instrumentation, and high-accuracy sampling at moderate speeds. The ADC0801S040 belongs to the data-acquisition IC hierarchy: ADC -> data converter -> data acquisition -> signal chain IC -> semiconductor. Key features include a maximum sampling rate of 40 MSPS, single-ended analog input with 2.7 V to 5.5 V input range, CMOS/TTL-compatible digital I/O, and an integrated sleep mode that reduces device power consumption when not converting. The 20-LSSOP (4.40 mm width) package provides a compact surface-mount footprint suitable for high-density PCB designs. Operating temperature range is -20 C to +75 C (commercial grade), and the device is supplied in tube packaging as the standard shipping format. The internal architecture uses a resistive-ladder DAC combined with a comparator and SAR logic to perform 8 successive approximations per conversion cycle. Each conversion takes approximately 8 clock cycles, after which the parallel output bus (DB0-DB7) presents the conversion result until the next sample. The sleep-mode pin allows the user to gate the converter's analog/digital supply current when the application is idle. Typical applications include video digitisation, general-purpose data acquisition, image processing front-ends, and IF/baseband sampling in communications receivers. It is also used in battery-powered portable instrumentation where the low-power sleep mode reduces quiescent current. The wide input range (2.7 V to 5.5 V) supports single 3.3 V and 5 V system rails. When designing with this device, ensure the analog input bandwidth and source-impedance driving network satisfies the datasheet acquisition-time requirement to avoid gain error. Use a low-jitter clock to keep aperture uncertainty low at 40 MSPS, and decouple AVDD/DVDD independently with 100 nF ceramic capacitors placed close to the supply pins. Sleep-mode timing must be respected if the part is duty-cycled to save power. This page synthesises distributor pricing (DigiKey, Mouser), drop-in alternative information and design considerations drawn from the manufacturer datasheet, providing a unified reference beyond what is shown on any single distributor product page.