Mga Produkto (44,000+)

WM8962ECS/R - 24-Bit Stereo Audio Codec | Cirrus Logic
WM8962ECS/R

WM8962ECS/R - 24-Bit Stereo Audio Codec | Cirrus Logic

The Cirrus Logic WM8962ECS/R is a 24-bit stereo audio codec with I2C and SPI control in a 49-ball WLCSP measuring 3.59 mm by 3.98 mm. The device combines a 98 dB ADC, a 94 dB DAC, and an integrated Class-W headphone amplifier, making it suitable for compact audio products that need high-resolution conversion and efficient headphone drive. An audio codec is an integrated circuit that converts digital audio data into analog signals and analog audio inputs into digital PCM data. It sits between a digital audio host, such as a microprocessor or application processor, and external audio transducers. A typical stereo codec also integrates programmable gain, filters, headphone-output circuitry, and a digital control interface to reduce the number of discrete components required in portable equipment. The WM8962ECS/R provides a 24-bit stereo interface and supports both I2C and SPI control. Its verified 98 dB ADC and 94 dB DAC figures establish the advertised dynamic-range performance for the conversion sections. The ultra-low-power codec architecture targets battery-powered audio equipment where conversion performance, standby consumption, and board area are all important constraints. Its integrated charge pump creates a ground-referenced headphone output, eliminating the need for DC-blocking capacitors on the headphone outputs. The design also uses Cirrus Logic Class-W amplifier techniques and a dual-mode charge-pump architecture to optimize efficiency and power consumption during playback. A DC servo reduces output ground offsets, improving headphone-output behavior and simplifying the external signal path. Typical uses include smartphone and tablet audio paths, portable media players, connected audio accessories, digital personal audio devices, and compact consumer equipment with analog headphone outputs. The combination of a 49-ball WLCSP, integrated stereo converters, flexible digital control, and capacitor-free headphone outputs is especially useful when PCB area is constrained. Designers should verify the complete pin assignment, exposed-ball configuration, supported digital audio formats, clocking requirements, and analog routing against the manufacturer datasheet before layout. Decoupling, analog grounding, headphone routing, and charge-pump layout remain critical because this highly integrated device combines sensitive converters, digital interfaces, and switching amplification on one small package. This page combines verified distributor availability, exact package information, converter-performance figures, and manufacturer-described charge-pump and Class-W features. It also records where complete specifications are unavailable, preventing unsupported electrical values from being presented as engineering facts.

RFQ Kontak
WM8962ECSN/R - 24-Bit Stereo Audio Codec | Cirrus Logic
WM8962ECSN/R

WM8962ECSN/R - 24-Bit Stereo Audio Codec | Cirrus Logic

The Cirrus Logic WM8962ECSN/R is a 24-bit stereo audio codec with I2C and SPI control interfaces, audio-enhancement DSP, and a 49-WLCSP package measuring 3.59 mm by 3.98 mm. It combines digital-to-analog and analog-to-digital conversion in a compact surface-mount package intended for audio processing and signal-chain designs. An audio codec is an interface IC that converts digital audio data into analog signals and analog sound signals into digital data. As a stereo codec, the WM8962ECSN/R handles two audio channels. Its 24-bit data resolution supports high-resolution audio architectures, while the integrated audio-enhancement DSP provides processing functions within the same device rather than requiring a separate external processor for supported use cases. The WM8962ECSN/R supports both I2C and SPI control buses, giving the host processor a choice of communication methods. I2C is useful in compact systems where pin count and wiring simplicity are priorities, while SPI can provide a different host-interface tradeoff when clocking and data-transfer characteristics suit the application. The exact register implementation, supported audio formats, and control sequence should be confirmed in the manufacturer datasheet. The physical package is a 49-WLCSP with a stated body size of 3.59 mm by 3.98 mm. Other manufacturer-listing data describes the package as PBGA49 or WCSP-49, approximately 3.60 mm by 3.90 mm, with 0.50 mm pitch, 0.70 mm height, MO-211C construction, and lead-free construction. These dimensions make the device suitable for compact portable and embedded audio products where board area is tightly constrained. Typical design environments include portable media devices, smart audio endpoints, headset and microphone signal chains, multimedia appliances, and embedded systems requiring stereo conversion. System-level success depends on correct analog input and output routing, suitable decoupling, clean power rails, an appropriately designed clock source, and layout that separates sensitive audio signals from digital switching activity. PCB implementation should follow the manufacturer land pattern and pin-assignment table exactly. Place input and output capacitors adjacent to their relevant device pins, provide a continuous ground reference, and keep high-speed digital clock and control routing away from microphone or line-level analog inputs. Validate the assembled design for channel crosstalk, idle-channel noise, clock jitter sensitivity, and start-up behavior. This product page consolidates the confirmed package, interface, resolution, and sourcing information while distinguishing documented facts from details that must be checked against the current manufacturer datasheet. It also identifies same-brand stereo-codec alternatives that require explicit pin, feature, and sample-rate validation before being treated as drop-in replacements.

RFQ Kontak
WM8963ECSN/R - 24-Bit Stereo Audio Codec | Cirrus Logic
WM8963ECSN/R

WM8963ECSN/R - 24-Bit Stereo Audio Codec | Cirrus Logic

The Cirrus Logic WM8963ECSN/R is a 24-bit stereo audio interface and codec with I2C and SPI control, packaged as a 49-ball WLCSP measuring 3.59 mm by 3.98 mm. Its compact surface-mount format supports space-constrained audio products where the digital host interface, analog audio path, and physical footprint must coexist within a small board area. An audio codec is an interface IC that converts digital audio samples into analog signals and, depending on the implementation, supports analog signal conversion in the opposite direction. Within the broader semiconductor hierarchy, a codec belongs to the audio interface family, connects into the signal-processing and power-management portions of a system, and is controlled by a host processor through a serial bus. The WM8963ECSN/R combines that interface role with a stereo-audio focus and a 24-bit resolution identifier. The WM8963ECSN/R supports both I2C and SPI host-control interfaces, allowing a system architect to select the digital control method that best fits the processor, firmware, board-routing constraints, and peripheral configuration. Its 49-ball WLCSP is intended for high-density PCB assembly. The package dimensions are 3.59 mm by 3.98 mm, making physical design checks essential when placing the codec beside an application processor, memory, amplifier, connector, and microphone circuitry. The 49-ball package provides the physical interface for the codec's power, digital control, data, analog audio, and supporting functions. Because the complete pin-assignment and signal descriptions must match the exact ball numbering of this package, use the Cirrus Logic datasheet ball table when creating the symbol, assigning PCB nets, and checking exposed-ball or thermal requirements. Do not infer a ball function from the package name or from a diagram belonging to another package variant. Typical uses include portable audio equipment, smart speakers, voice-control products, headsets, soundbars, and compact embedded systems. The I2C option is particularly useful for low-pin-count control architectures, while SPI can suit systems that already use that bus for peripherals or require a different control timing strategy. The stereo codec can sit between a digital audio processor and an analog output stage, allowing host-generated audio to be converted for downstream amplification. PCB implementation should prioritize short analog and digital audio routes, continuous ground references, and placement of required bypass capacitors near the associated balls. Review the manufacturer reference circuit and pin table for the exact supply, interface, analog, and clock connections. Pay particular attention to exposed-ball requirements, board-cleanliness practices, and the relationship between power-entry points and sensitive audio nodes. This product record combines package identification, interface facts, application guidance, sourcing questions, and design checks in one concise reference. It also separates verified catalog attributes from detailed electrical parameters that still require confirmation from the manufacturer datasheet, helping engineers evaluate the WM8963ECSN/R before committing to a high-density PCB layout.

RFQ Kontak
WM8974CGEFL/V - 24-Bit Mono Audio Codec | Cirrus Logic
WM8974CGEFL/V

WM8974CGEFL/V - 24-Bit Mono Audio Codec | Cirrus Logic

The Cirrus Logic WM8974CGEFL/V is a 24-bit mono audio codec with an integrated speaker driver, built-in phase-locked loop, and on-chip digital gain, packaged in a 24-pin QFN configuration with an exposed pad. The device is identified as a 4 mm by 4 mm surface-mount audio interface and is intended for compact systems requiring digital audio playback, microphone capture, and direct speaker-drive capability. An audio codec is a semiconductor interface that converts digital audio samples into analog signals, converts analog microphone signals into digital data, and often includes programmable gain, filtering, and output-driver functions. Within the wider hierarchy, the WM8974CGEFL/V belongs to the audio codec category, which is part of interface ICs and ultimately serves as a mixed-signal subsystem within a power-management and signal-processing architecture. Its integrated speaker driver can reduce the number of separate output components required in small audio systems. The WM8974CGEFL/V provides a 24-bit audio interface, digital gain control, an integrated phase-locked loop, and a mono speaker-driver stage. Its -40 °C to +85 °C operating-temperature range supports industrial and commercial equipment. The 24-QFN exposed-pad package also promotes heat transfer through the PCB copper area, although actual thermal performance depends on the layout, copper area, surrounding temperature, and audio-output load. Digital gain is particularly useful in systems where the software or system controller must adjust playback level without changing passive components. The built-in phase-locked loop supports systems in which the audio clock must be derived from or synchronized with another digital block. The mono codec architecture is suited to products such as alarm systems, industrial annunciators, compact voice terminals, and embedded audio modules that need one amplified audio path rather than a full stereo codec. Typical applications include industrial audible alarms, building-control panels, communication terminals, portable voice accessories, and embedded control systems with a local speaker. In these designs, the codec can accept digital audio from a host processor, provide programmable gain, and drive a loudspeaker through the integrated output stage. The exposed pad remains a functional part of the package and should be connected according to the manufacturer's recommended footprint and thermal layout. PCB design should preserve the recommended decoupling topology and keep analog and digital return currents controlled. Place input, output, and bypass capacitors close to their associated pins, connect the exposed pad to the intended ground or pad-design net, and maintain the manufacturer-specified footprint dimensions. Audio performance also depends on correct clocking, speaker loading, analog grounding, and separation from switching noise. This product record combines the exact package, temperature, interface, and feature information with practical design guidance, sourcing instructions, and an explicit drop-in compatibility assessment. The comparison focuses on true pin-to-pin replacements rather than broadly similar codecs that require a different footprint, pin assignment, clock arrangement, or power architecture.

RFQ Kontak
WM8978CGEFL/V - 24-Bit Stereo Codec | Wolfson
WM8978CGEFL/V

WM8978CGEFL/V - 24-Bit Stereo Codec | Wolfson

The Wolfson Microelectronics plc WM8978CGEFL/V is a 24-bit stereo audio codec with an integrated speaker driver, digital I2S/PCM interfaces, and analog microphone, headphone, and line-output stages in a 32-QFN 5 x 5 mm package. It combines several signal-path functions commonly required in portable multimedia equipment, reducing the need for separate microphone, headphone, and speaker amplifiers. A stereo audio codec is a mixed-signal interface IC that converts digital audio samples into analog signals and accepts analog microphone signals before converting them back into digital audio. In the broader device hierarchy, the WM8978 belongs to the audio codec category, integrates into interface ICs, and ultimately supports portable audio systems such as multimedia phones, digital still cameras, and digital camcorders. The WM8978CGEFL/V integrates preamplifiers for stereo differential microphones and includes drivers for speakers, headphones, and differential or stereo line outputs. Its published interface format is 24-bit I2S/PCM, while its 32-QFN package measures 5 x 5 mm. This integration can shorten analog routing, reduce external amplifier count, and simplify portable-product layouts when the board area and power budget are tightly constrained. Its mixed-signal architecture supports a compact portable audio signal chain. Digital audio enters through the I2S or PCM interface, while the codec manages microphone capture and analog playback paths. The 5 x 5 mm QFN-32 package requires careful PCB layout because its exposed thermal pad and fine-pitch perimeter connections affect soldering, return paths, and heat spreading. Exact electrical ratings, sampling rates, clock requirements, and output-power limits must be confirmed from the manufacturer datasheet before layout release. Typical uses include portable media players, multimedia phones, digital cameras, camcorders, and compact audio accessories. It may also fit smart-home or embedded devices that need one IC for digital-to-analog playback, microphone capture, headphone output, and speaker drive. Designers should confirm that the selected speaker, microphone, and output network remain within the device's electrical and acoustic limits. A key design consideration is analog layout discipline. Place input and output capacitors near their associated pins, maintain short and symmetric analog routes, keep switching-supply and digital-clock nodes away from microphone inputs, and follow the datasheet reference layout for component selection and exposed-pad connection. Confirm the exact schematic values and pin definitions before production release. This product page combines the WM8978CGEFL/V interface and package details, replacement considerations, application guidance, comparison parameters, and practical layout notes to support faster component selection and hardware design.

RFQ Kontak
WM8983GEFL/RV - Stereo 24-Bit Audio Codec | Cirrus Logic
WM8983GEFL/RV

WM8983GEFL/RV - Stereo 24-Bit Audio Codec | Cirrus Logic

The Cirrus Logic WM8983GEFL/RV is a stereo mobile multimedia audio codec with 24-bit I2S and PCM interfaces, two ADC channels, two DAC channels, and an integrated 1 W speaker driver. It is packaged in a 32-pin QFN package measuring 5 mm by 5 mm. The combination of stereo conversion, digital audio interfaces, and direct speaker-drive capability makes the device suitable for portable equipment in which a separate speaker amplifier would increase board area and system complexity. An audio codec is an interface IC that converts analog audio signals into digital data and digital audio data back into analog signals. In a portable multimedia system, the WM8983GEFL/RV can sit between microphones or line-level audio inputs and an I2S or PCM-capable processor. Its speaker-drive capability can then provide an efficient output path for a small speaker or headphone-oriented audio subsystem. The WM8983GEFL/RV provides 24-bit audio resolution, stereo ADC and DAC channels, I2S and PCM data formats, and a 1 W speaker-driver stage. These features support modern digital audio processors while keeping the external component count relatively low. The 5 mm by 5 mm 32-QFN package also supports compact board layouts, although its exposed thermal pad and fine-pitch footprint require careful PCB layout and assembly planning. The device is described as a low-power, high-quality stereo codec intended for portable multimedia applications. Its integrated speaker driver reduces the need for a separate output amplifier in suitable low-power designs. Designers should still verify the speaker impedance, output waveform, thermal conditions, and supply configuration against the manufacturer datasheet before establishing a production design. Typical uses include portable media players, personal audio products, compact consumer electronics, mobile accessories, and embedded multimedia terminals. The I2S interface suits processors with a dedicated digital-audio peripheral, while PCM support offers an additional digital connection format. These interfaces allow captured or generated audio to be transferred digitally without external high-speed converters. The 32-QFN footprint requires attention to pad layout, exposed-pad soldering, and via placement. Keep analog input, headphone, and speaker outputs away from clock and data routing where practical, and follow the manufacturer’s recommended decoupling and grounding arrangement. Digital interfaces should be driven only when signal levels and timing comply with the device’s electrical limits. This page consolidates the available interface, resolution, channel-count, package, and speaker-drive information, adds practical application guidance, and identifies the limits of a replacement decision. Pin-level design work should use the manufacturer datasheet pin description and application information rather than inferring connectivity from the package outline.

RFQ Kontak
WM8983GEFL/V - 24-Bit Stereo Audio Codec | Cirrus Logic
WM8983GEFL/V

WM8983GEFL/V - 24-Bit Stereo Audio Codec | Cirrus Logic

The Cirrus Logic WM8983GEFL/V is a low-power, high-quality stereo audio codec designed for portable multimedia equipment. It combines two 24-bit ADCs, two 24-bit DACs, digital audio interfaces for I2S and PCM data, analog input and output mixing, and a 1 W mono speaker driver in a 32-QFN (5x5 mm) surface-mount package. A multimedia CODEC is a mixed-signal semiconductor that converts between digital audio streams and analog microphone, headphone, line, or speaker signals. Its functional hierarchy places the WM8983 among audio interface ICs, within audio codecs and ultimately the broader category of interface ICs. Integrating conversion, analog mixing, and speaker amplification reduces the number of discrete components required in portable audio designs. The WM8983 provides 24-bit stereo ADCs and 24-bit stereo DACs, with I2S and PCM digital interfaces for connection to a host processor or digital audio bus. Its flexible analog mixing block supports combined playback and voice communication paths. The integrated 1 W speaker drive output allows the codec to drive a small loudspeaker directly, making it useful where a separate headphone amplifier is not required. The device is supplied in a compact 32-QFN (5x5 mm) package suited to space-constrained handsets, portable media players, personal audio products, and embedded multimedia systems. Its low-power design targets battery-operated equipment where converter efficiency, standby behavior, and analog signal integrity influence both system heat and playback quality. Typical uses include portable music players, mobile media devices, voice-capable portable electronics, compact speakers, and multifunction personal-audio products. The stereo recording path can capture analog microphone or line-level inputs, while the DAC path and analog mixer provide digital playback, voice monitoring, and direct speaker output within one device. When laying out a WM8983GEFL/V board, place decoupling capacitors at the supply pins and route analog and digital return currents carefully to prevent codec noise from coupling into microphone or speaker signals. Confirm the exact clocking, digital-interface mode, and exposed-pad connection against the manufacturer datasheet before release. This page organizes the confirmed WM8983GEFL/V capabilities, package information, sourcing path, and engineering trade-offs for engineers evaluating stereo audio codec implementations. It also distinguishes the documented order-code variants and identifies where a genuine pin-to-pin substitute must be validated rather than assumed.

RFQ Kontak
WM8985CGEFL Stereo Audio Codec | Cirrus Logic | 32-QFN
WM8985CGEFL

WM8985CGEFL Stereo Audio Codec | Cirrus Logic | 32-QFN

The Cirrus Logic WM8985CGEFL is a stereo audio interface and multimedia codec with 24-bit I2S and PCM digital audio support. It is packaged in a 32-QFN (5x5 mm) surface-mount package and is associated with Class D headphone-driver functionality. The part is intended for compact embedded audio systems where a single codec must handle digital audio interfaces, analog audio conversion, and headphone-output support. A multimedia codec is an integrated audio interface IC that converts between digital audio streams and analog audio signals while providing control and signal-conditioning functions for speakers, headphones, microphones, and line-level circuitry. The WM8985CGEFL sits within the broader hierarchy of audio codec, audio interface IC, multimedia IC, and semiconductor. The WM8985CGEFL is identified in distributor listings as a stereo audio interface supporting 24-bit I2S and PCM formats. Its 32-QFN (5x5 mm) package supports high-density PCB layouts and is suitable for portable equipment, consumer audio products, communications equipment, and embedded audio platforms. The listing also identifies Class D headphone-driver support as a key feature for applications requiring efficient headphone amplification. The 5x5 mm QFN format can help reduce board area compared with larger leaded packages, but exposed-pad thermal management and careful PCB layout remain important. Decoupling capacitors should be placed close to the device power pins, while analog and digital ground and power connections should follow the manufacturer pin-description and layout guidance. Signal-routing decisions should also account for the 24-bit audio path and the separation of analog and digital sections. Typical uses include USB and embedded audio accessories, portable media equipment, communications terminals, smart-device audio paths, and compact headphone interfaces. A system designer should confirm the complete electrical limits, clocking requirements, supported sample rates, analog input/output limits, and pin-level connections against the manufacturer datasheet before releasing a PCB. This product page consolidates the exact WM8985CGEFL package and interface information into a structured component record. It also identifies the intended codec use cases and distinguishes the documented part from unsupported substitute claims. When replacing an existing WM8985CGEFL, verify the complete 32-pin land pattern, exposed-pad connection, digital audio format, clock configuration, analog biasing, and supply sequencing rather than relying on the codec function alone. A functionally similar audio codec is not automatically a pin-to-pin drop-in replacement.

RFQ Kontak
WM8985CGEFL/R Stereo Audio Codec | Cirrus Logic | 32-QFN (Tape & Reel)
WM8985CGEFL/R

WM8985CGEFL/R Stereo Audio Codec | Cirrus Logic | 32-QFN (Tape & Reel)

The Cirrus Logic WM8985CGEFL/R is a stereo audio interface and multimedia codec with 24-bit I2S and PCM digital audio support. It is packaged in a 32-QFN (5x5 mm) surface-mount package and is associated with Class D headphone-driver functionality. The part is intended for compact embedded audio systems where a single codec must handle digital audio interfaces, analog audio conversion, and headphone-output support. A multimedia codec is an integrated audio interface IC that converts between digital audio streams and analog audio signals while providing control and signal-conditioning functions for speakers, headphones, microphones, and line-level circuitry. The WM8985CGEFL/R sits within the broader hierarchy of audio codec, audio interface IC, multimedia IC, and semiconductor. The WM8985CGEFL/R is identified in distributor listings as a stereo audio interface supporting 24-bit I2S and PCM formats. Its 32-QFN (5x5 mm) package supports high-density PCB layouts and is suitable for portable equipment, consumer audio products, communications equipment, and embedded audio platforms. The listing also identifies Class D headphone-driver support as a key feature for applications requiring efficient headphone amplification. The 5x5 mm QFN format can help reduce board area compared with larger leaded packages, but exposed-pad thermal management and careful PCB layout remain important. Decoupling capacitors should be placed close to the device power pins, while analog and digital ground and power connections should follow the manufacturer pin-description and layout guidance. Signal-routing decisions should also account for the 24-bit audio path and the separation of analog and digital sections. Typical uses include USB and embedded audio accessories, portable media equipment, communications terminals, smart-device audio paths, and compact headphone interfaces. A system designer should confirm the complete electrical limits, clocking requirements, supported sample rates, analog input/output limits, and pin-level connections against the manufacturer datasheet before releasing a PCB. This product page consolidates the exact WM8985CGEFL/R package and interface information into a structured component record. It also identifies the intended codec use cases and distinguishes the documented part from unsupported substitute claims. When replacing an existing WM8985CGEFL/R, verify the complete 32-pin land pattern, exposed-pad connection, digital audio format, clock configuration, analog biasing, and supply sequencing rather than relying on the codec function alone. A functionally similar audio codec is not automatically a pin-to-pin drop-in replacement.

RFQ Kontak
WM8988LGECN/V - Stereo 24-Bit Audio Codec | Cirrus Logic
WM8988LGECN/V

WM8988LGECN/V - Stereo 24-Bit Audio Codec | Cirrus Logic

The Cirrus Logic WM8988LGECN/V is a low-power stereo audio codec with a 24-bit interface, synchronous operation, and CMOS technology in a 28-pin QFN package measuring 4 mm by 4 mm. Designed for portable audio equipment, it combines stereo signal processing and digital audio interfacing in a compact surface-mount package rated for -25°C to +85°C operation. An audio codec is an interface IC that converts digital audio data into an analog audio signal, converts analog audio back into digital data, or performs both functions. In the broader hierarchy, a codec belongs to the audio interface family, then to interface ICs, and finally to integrated circuits. Stereo codecs support two audio channels and are commonly used where a system needs headphone, microphone, line, or speaker-path processing without a large discrete analog implementation. The WM8988LGECN/V is identified as a 24-bit stereo audio interface with low-power operation. Its synchronous CMOS implementation provides a defined digital interface for portable audio systems. The 28-QFN package also reduces board footprint compared with larger leaded or high-pin-count packages, making the device suitable for space-constrained consumer and portable products. The part operates over a -25°C to +85°C temperature range and uses a 4 mm by 4 mm QFN package with 28 terminals. Its operating architecture is described as synchronous, which helps coordinate digital audio transfer with the associated system clock and data signals. The package and temperature specification support applications that require a compact, surface-mount audio interface rather than a through-hole codec solution. Typical applications include portable music players, headphone-equipped personal audio products, connected audio accessories, and compact consumer systems requiring stereo playback or recording. The 24-bit interface and low-power design are especially relevant when product designers need audio conversion performance while preserving board area and system power budget. PCB implementation should follow the manufacturer datasheet for exposed-pad connection, decoupling, clock routing, and analog layout. A QFN package also requires careful assembly inspection because its fine-pitch leads and exposed thermal pad are difficult to inspect visually after soldering. Confirm pin assignments and recommended component values against the manufacturer datasheet before releasing the layout.

RFQ Kontak
WM8993ECS/RV - 24-Bit Stereo Audio Codec | Cirrus Logic
WM8993ECS/RV

WM8993ECS/RV - 24-Bit Stereo Audio Codec | Cirrus Logic

Cirrus Logic WM8993ECS/RV is a 24-bit stereo audio interface IC with two ADCs, two DACs, sigma-delta conversion, a stereo speaker driver, and a Class W headphone driver. The device is supplied in a 48-terminal WLCSP package measuring 3.65 mm by 3.55 mm, making it suitable for compact portable audio equipment. Its nominal supply voltage is 1.2 V, and its specified operating temperature range extends from -40°C to 85°C. An audio codec is an interface IC that converts analog audio signals into digital data and reconstructs digital audio into analog signals. As part of the broader hierarchy of audio interface ICs, codecs connect microphones, speakers, headphones, and other analog audio hardware to a digital audio processor. Their conversion architecture, signal-to-noise performance, integrated analog drivers, package size, and power requirements determine how effectively they fit portable and embedded systems. The WM8993ECS/RV combines a 24-bit resolution with two ADCs and two DACs in a single device. Listed ADC and DAC signal-to-noise ratios are 95 dB and 100 dB, respectively. Sigma-delta conversion supports high-resolution digital audio processing, while the integrated stereo speaker and Class W headphone drive functions reduce the need for separate output-driver circuitry in suitable speaker and headphone loads. The WM8993ECS/RV belongs to the Wolfson audio-hub family associated with Cirrus Logic. Its integration is valuable in space-constrained systems because analog capture, digital playback, and headphone or speaker drive functions are consolidated within one 3.65 mm by 3.55 mm package. Exact clocking, supported sample rates, analog input configuration, output-power ratings, and control-interface details must be confirmed against the manufacturer datasheet before schematic capture. Typical uses include smartphone and tablet audio, portable media players, Bluetooth audio accessories, headset electronics, compact voice-capture equipment, and connected audio products. The low-profile WLCSP footprint supports high-density PCB construction, while the integrated drivers can simplify signal routing compared with a discrete codec-and-amplifier implementation. Designers should verify the supported microphone and line-input topology, required external passive components, digital interface voltage levels, clock sources, and thermal performance for the selected speaker impedance. The package also requires careful PCB layout with short analog paths and appropriate grounding to preserve signal integrity in compact systems. This product page combines the manufacturer-part characteristics, converter configuration, package details, application guidance, and verified sourcing links into one engineering-focused reference. It also distinguishes directly documented attributes from parameters that must be confirmed during component selection and hardware validation.

RFQ Kontak
WM8998ECS/R - 24-Bit Hi-Fi Audio Hub | Cirrus Logic
WM8998ECS/R

WM8998ECS/R - 24-Bit Hi-Fi Audio Hub | Cirrus Logic

Cirrus Logic WM8998ECS/R is a 24-bit HD audio hub and SLIMbus audio interface housed in a 117-WCSP package measuring 5.35 mm by 4.09 mm. The verified distributor records identify the device as a Hi-Fi coding-switch solution intended for compact digital audio systems. Its interface orientation makes it suitable for products that require a low-power, highly integrated audio front end while retaining a digital audio link to a host processor. An audio codec is an integrated circuit that converts digital audio data into an analog output and converts analog microphone or line inputs back into digital data. In the product hierarchy, a codec is an audio interface IC within the broader class of interface ICs. The WM8998ECS/R is positioned for portable and embedded audio functions where component count, board area, and host connectivity are important design constraints. The verified product listing specifically identifies a 24-bit HD audio interface, SLIMbus connectivity, and a 117-WCSP package. These confirmed attributes make the part relevant to smartphone, tablet, portable-media, headset, and embedded-audio designs. The 5.35 mm by 4.09 mm package reduces board footprint, although its 117-ball construction requires careful assembly, inspection, and PCB-layout planning. Technical evaluation must be completed against the manufacturer datasheet because the supplied distributor results do not expose the complete electrical tables. Sample rate coverage, supported clock rates, microphone bias, codec specifications, digital levels, power-supply requirements, and thermal limits are not available in the verified data and therefore cannot be safely inferred. Designers should also confirm the exact exposed-pad, ball-map, and recommended-land-pattern details before layout release. Typical implementation places the WM8998ECS/R between one or more analog audio transducers and a digital audio host connected through SLIMbus. Its integrated hub role can simplify system routing in devices containing speaker, headphone, microphone, and line-level audio paths. The correct external amplifiers, passive network, clocking, and decoupling must be selected from the manufacturer reference design rather than inferred from the distributor summaries. The primary design consideration is PCB implementation. A 117-WCSP package has a much denser interconnect than a conventional leaded package and can create soldering, inspection, and repair challenges. Confirm whether the assembled board will use optical inspection or X-ray inspection, and use the manufacturer-approved footprint and reflow profile to reduce assembly defects. The verified data does not expose pin names, so a complete ball assignment cannot be published here. This product record combines verified distributor pricing, package information, sourcing links, and engineering-oriented selection guidance. It also separates confirmed facts from unavailable datasheet parameters and avoids presenting generic codec specifications as facts about the WM8998ECS/R.

RFQ Kontak
WM9001GEFL - 1W Class AB/D Speaker Driver | Cirrus Logic
WM9001GEFL

WM9001GEFL - 1W Class AB/D Speaker Driver | Cirrus Logic

The Cirrus Logic WM9001GEFL is a 1 W mono dual-mode Class AB and Class D speaker driver packaged in a 16-pin QFN with an exposed pad. The distributor data identifies it as an audio amplifier IC with a 1 W output rating, Class AB and Class D operating modes, and a compact 3 x 3 mm QFN package. These characteristics place it in the speaker-driver hierarchy of audio amplifier ICs used to drive small electrodynamic transducers. A speaker-driver amplifier is an integrated circuit that accepts an analog audio signal and delivers enough current and voltage to move a miniature speaker cone. The dual-mode architecture gives a system designer the option to select Class AB behavior for linear output or Class D behavior for higher conversion efficiency. The WM9001GEFL is therefore positioned for compact audio products where speaker output, board area, and energy consumption must be balanced. The WM9001GEFL's principal verified specifications are its 1 W output capability, single-channel mono configuration, support for both Class AB and Class D amplification, and 16-QFN package with an exposed pad. The exposed pad supports heat transfer from the IC into the printed circuit board. Because no verified voltage, current, frequency-response, distortion, thermal-resistance, or shutdown information was supplied, those values must be confirmed in the manufacturer datasheet before final design release. Technically, this device belongs to the integrated-circuit amplifier family and more specifically to speaker-driver audio ICs. Its 3 x 3 mm QFN package supports high-density PCB layouts but demands careful control of exposed-pad soldering, copper thermal paths, and acoustic-mechanical layout. Class AB and Class D modes can also differ in EMI behavior and power efficiency, so mode selection should be based on the complete analog path, speaker impedance, and enclosure conditions rather than package size alone. Typical uses include portable-device speakers, compact consumer-audio products, personal-audio accessories, small embedded audio systems, and accessory modules requiring a mono 1 W drive stage. In these applications, the device can sit near the speaker connector to shorten the high-current output path, reduce load-related board losses, and simplify the analog architecture. Designers should still validate output power at the intended speaker impedance and frequency range. The primary design consideration is thermal management. Although the package includes an exposed pad, continuous Class AB output near the 1 W rating can dissipate more power than Class D operation. The pad should be connected to a suitable ground plane and thermal copper area, while input, feedback, and output routing should avoid the loudspeaker return path. Decoupling and output-filter values must come from the manufacturer application guidance. This product record consolidates verified distributor inventory, package information, source links, engineering caveats, and selection guidance that are not consolidated on a typical distributor listing. Where the supplied evidence does not establish a parameter or a true pin-compatible substitute, the record explicitly marks the gap rather than presenting an unsupported value.

RFQ Kontak
WM9001GEFL/R - 1W Class AB/D Speaker Driver | Cirrus Logic (Tape & Reel)
WM9001GEFL/R

WM9001GEFL/R - 1W Class AB/D Speaker Driver | Cirrus Logic (Tape & Reel)

The Cirrus Logic WM9001GEFL/R is a 1 W mono dual-mode Class AB and Class D speaker driver packaged in a 16-pin QFN with an exposed pad. The distributor data identifies it as an audio amplifier IC with a 1 W output rating, Class AB and Class D operating modes, and a compact 3 x 3 mm QFN package. These characteristics place it in the speaker-driver hierarchy of audio amplifier ICs used to drive small electrodynamic transducers. A speaker-driver amplifier is an integrated circuit that accepts an analog audio signal and delivers enough current and voltage to move a miniature speaker cone. The dual-mode architecture gives a system designer the option to select Class AB behavior for linear output or Class D behavior for higher conversion efficiency. The WM9001GEFL/R is therefore positioned for compact audio products where speaker output, board area, and energy consumption must be balanced. The WM9001GEFL/R's principal verified specifications are its 1 W output capability, single-channel mono configuration, support for both Class AB and Class D amplification, and 16-QFN package with an exposed pad. The exposed pad supports heat transfer from the IC into the printed circuit board. Because no verified voltage, current, frequency-response, distortion, thermal-resistance, or shutdown information was supplied, those values must be confirmed in the manufacturer datasheet before final design release. Technically, this device belongs to the integrated-circuit amplifier family and more specifically to speaker-driver audio ICs. Its 3 x 3 mm QFN package supports high-density PCB layouts but demands careful control of exposed-pad soldering, copper thermal paths, and acoustic-mechanical layout. Class AB and Class D modes can also differ in EMI behavior and power efficiency, so mode selection should be based on the complete analog path, speaker impedance, and enclosure conditions rather than package size alone. Typical uses include portable-device speakers, compact consumer-audio products, personal-audio accessories, small embedded audio systems, and accessory modules requiring a mono 1 W drive stage. In these applications, the device can sit near the speaker connector to shorten the high-current output path, reduce load-related board losses, and simplify the analog architecture. Designers should still validate output power at the intended speaker impedance and frequency range. The primary design consideration is thermal management. Although the package includes an exposed pad, continuous Class AB output near the 1 W rating can dissipate more power than Class D operation. The pad should be connected to a suitable ground plane and thermal copper area, while input, feedback, and output routing should avoid the loudspeaker return path. Decoupling and output-filter values must come from the manufacturer application guidance. This product record consolidates verified distributor inventory, package information, source links, engineering caveats, and selection guidance that are not consolidated on a typical distributor listing. Where the supplied evidence does not establish a parameter or a true pin-compatible substitute, the record explicitly marks the gap rather than presenting an unsupported value.

RFQ Kontak
WM9010ECSN/R - Class G Stereo Driver | Cirrus Logic
WM9010ECSN/R

WM9010ECSN/R - Class G Stereo Driver | Cirrus Logic

Cirrus Logic WM9010ECSN/R is a low-power, two-channel Class G stereo headphone-driver IC rated at 12 W in a 12-W-CSP package measuring 1.84 x 1.34 mm. The device supports a 16 ohm headphone load and achieves THD+N of -90 dB at 20 mW into 32 ohm with a 1.8 V supply. Its integrated charge pump generates split-rail voltage supplies for the ground-referenced headphone output stage. A Class G headphone amplifier is an audio amplifier architecture that combines signal-dependent output characteristics with efficient power delivery. Unlike a continuously biased linear output stage, Class G changes its internal supply behavior according to signal level and load demand. In a portable headset or portable media device, this approach helps reduce power consumed during quiet passages while retaining the output capability needed for louder playback. The WM9010ECSN/R belongs to the broader audio-amplifier IC and power-management semiconductor hierarchy. The WM9010ECSN/R provides a stereo output configuration, Class G efficiency, and an integrated charge pump in a compact surface-mount package. Its 12-lead CSP is only 1.84 x 1.34 x 0.7 mm, making it suitable for space-constrained portable equipment. A listed output-power figure of 34 mW applies to the characterized operating condition, while the distributor package classification identifies the device as a 12 W-class headphone driver. Headphone impedance and supply voltage remain important when evaluating available output power and distortion. Audio performance depends on the selected load and operating point. The manufacturer specification of THD+N at -90 dB, 20 mW output, 32 ohm load, and 1.8 V supply demonstrates low distortion at a practical portable-audio level. The integrated charge pump produces the positive and negative rail voltages needed by the ground-referenced headphone driver, reducing the number of external negative-supply components while adding charge-pump switching considerations to PCB layout. Typical applications include wired and wireless headphones, Bluetooth headset audio paths, portable game accessories, compact USB-C audio devices, and battery-powered music players. The small 12-W-CSP footprint supports dense layouts, while the 16 ohm load specification directly addresses conventional stereo-headphone impedances. In each application, the headphone source should be AC-coupled as required by the circuit design, and the power supply must remain within the device's specified operating limits. The most important design consideration is PCB implementation around a compact CSP with an integrated charge pump. Place input, output, supply, and decoupling connections according to the manufacturer layout guidance, keep the charge-pump and sensitive audio paths physically separated, and provide a quiet ground return. Confirm output-power capability at the actual supply voltage, channel load, and headphone impedance rather than relying only on the headline package classification. This product page combines the WM9010ECSN/R electrical characteristics, package data, drop-in-replacement review, application guidance, and design notes into a concise engineering reference. It is intended to accelerate schematic planning, footprint verification, and audio-path design without replacing the complete manufacturer datasheet.

RFQ Kontak
WM9081GICN/V - 24-Bit Mono DAC with 2.6W Amplifier | Cirrus Logic
WM9081GICN/V

WM9081GICN/V - 24-Bit Mono DAC with 2.6W Amplifier | Cirrus Logic

The Cirrus Logic WM9081GICN/V is a mono 24-bit digital-to-analog converter with an integrated 2.6 W Class AB/Class D speaker amplifier, supplied in a 28-pin QFN package measuring 4 x 4 mm. It accepts I2S, DSP, LJ, and RJ digital audio data and is intended for space-constrained portable equipment where a single device must provide high-resolution digital-to-analog conversion and speaker drive. The operating voltage range is 1.71 V to 3.6 V, and the specified temperature range is -40 °C to +85 °C. An audio DAC converts digital audio samples into an analog voltage signal suitable for an audio amplifier or speaker driver. The WM9081GICN/V combines that conversion function with a programmable output stage and integrated mobile parametric equalization. Its fully programmable EQ coefficients allow speaker and enclosure characteristics to be optimized, while programmable dynamic-range control supports louder playback at low listening levels. The result is a compact audio signal-chain component that reduces the need for separate DAC and speaker-driver packages. The device supports 2-wire, 3-wire, 4-wire, and hardware control modes, with digital audio formats including LJ, RJ, I2S, and DSP. TDM support broadens its usefulness in multi-channel portable audio systems where several codec or converter functions share one digital bus. A thermal-shutdown interrupt provides a system-level indication that the integrated output stage has entered its protected operating condition. The manufacturer also identifies programmable gain as part of the device feature set. Typical applications include portable media players, mobile phones, compact personal audio systems, docking speakers, and other battery-powered products with an integrated single-speaker output. Placing the DAC and amplifier in one package reduces board area, external component count, and the number of signal connections between the digital audio source and the speaker. Design layouts should follow the manufacturer datasheet for decoupling, exposed-pad grounding, and analog output routing. Keep the digital interface traces away from the speaker output and amplifier supply nodes to reduce the chance of switching-edge coupling into the audio path. Confirm the configured control mode and digital format in firmware before enabling the output stage. This page organizes the WM9081GICN/V specifications, application guidance, package details, and sourcing information into a single engineering reference for compact mono audio output designs.

RFQ Kontak
WM9082ECSN/R - 3W Mono PDM Class D Driver | Cirrus Logic
WM9082ECSN/R

WM9082ECSN/R - 3W Mono PDM Class D Driver | Cirrus Logic

The Cirrus Logic WM9082ECSN/R is a 3 W mono Class D speaker-driver IC with a PDM audio input, housed in a 9-ball W-CSP package measuring 1.57 mm by 1.47 mm. The device is intended for compact systems that receive digital audio directly from a PDM-compatible source, avoiding a separate analog audio input stage. Its Class D output architecture supports efficient speaker drive, while the small package supports space-constrained portable products. A Class D audio amplifier is a switching power amplifier that converts a digital or analog audio signal into a pulse-width-modulated output. The switching elements deliver energy to the speaker rather than dissipating the entire audio waveform as linear amplifiers do. A PDM input, also called pulse-density modulation, represents audio samples as a one-bit stream whose density changes over time. In the signal chain, the WM9082 belongs to the audio amplifier hierarchy and converts a PDM source into a mono Class D speaker output. The WM9082ECSN/R provides a single mono output channel and is identified as a 3 W Class D speaker driver. Its operating characteristics include PDM input support and automatic output enablement when PDM audio data is detected or when a valid Start-Up Control Code is received. These functions are useful in portable and embedded audio products because they allow the amplifier to remain inactive until valid audio activity is present, helping reduce unnecessary system activity. The compact 9-W-CSP construction is suitable for wearables, portable speakers, smart-home accessories, and compact consumer electronics where board area is limited. Because the package has a small thermal and electrical footprint, careful PCB layout is important. The speaker output, ground connection, PDM clock and data lines, supply connections, and any external filtering components should follow the manufacturer reference layout and recommended component values. This page emphasizes the distinctions that matter during schematic capture, PCB implementation, and sourcing. The WM9082 is most appropriate when the host processor or codec already supplies PDM audio and the system needs a compact mono speaker stage. It is less suitable for designs requiring conventional analog line input, multiple output channels, or a larger specified output-power level without reviewing the complete datasheet limits. The available listings also describe the device as a Cirrus Logic mono Class D audio amplifier, while the underlying datasheet identifies the original manufacturer as Wolfson Microelectronics. Use the manufacturer datasheet for the definitive electrical limits, recommended application circuit, pin description, exposed-ball configuration, and startup-code behavior. In particular, verify the allowed supply range, output-power conditions, speaker impedance, decoupling requirements, clocking limits, and PCB land pattern before release. The 1.57 mm by 1.47 mm package also makes assembly capability and land-pattern validation important during hardware planning. This page organizes the key WM9082ECSN/R specifications, sourcing information, application guidance, and replacement constraints in one place. It also distinguishes confirmed drop-in substitutions from broadly similar Class D drivers, helping engineers avoid choosing a device merely because its output wattage appears similar but whose package, pinout, input architecture, or control interface differs.

RFQ Kontak
WM9094ECS/R - 2W Mono Class D/AB Amplifier | Cirrus Logic
WM9094ECS/R

WM9094ECS/R - 2W Mono Class D/AB Amplifier | Cirrus Logic

Cirrus Logic WM9094ECS/R is a 1-channel mono audio amplifier IC delivering up to 2 W into a 4-ohm load, with both Class D and Class AB operation in a 20-WCSP package measuring 2.53 mm by 2.07 mm. The device operates from a 2.7 V to 5.5 V supply and is intended for compact low-power audio systems. An audio amplifier is an integrated circuit that converts an input audio signal into sufficient output power to drive a loudspeaker or other transducer. Class AB amplifiers provide linear operation with comparatively continuous output current, while Class D amplifiers switch the output stage to improve power-conversion efficiency. The WM9094ECS/R supports both operating modes, giving designers flexibility according to their efficiency, distortion, and thermal requirements. Key features include Class D and Class AB output capability, a 2 W maximum output-power rating into 4 ohms, integrated depop circuitry, integrated thermal protection, and a surface-mount 20-WCSP package. The 2.7 V minimum supply voltage supports portable and space-constrained equipment, while the 5.5 V maximum supply voltage accommodates common low-voltage power rails. The WM9094ECS/R is identified as a mono, one-channel amplifier rather than a multi-channel power amplifier. Its compact 2.53 mm by 2.07 mm package can reduce board area in mobile accessories, personal-audio products, and other integrated audio equipment. The manufacturer and distributor listings identify it as an ultra-low-power audio subsystem and list the part as obsolete. Typical applications include compact speaker systems, portable audio accessories, and low-voltage embedded products where a single amplified channel is sufficient. System-level implementation must account for the 2.7 V to 5.5 V supply range, speaker impedance, output power, thermal conditions, and the small-area land-pattern requirements of the 20-WCSP package. The principal design consideration is the obsolete lifecycle status. Designers should verify availability, source quality, and long-term supply before committing to a new production design. For a new design with obsolete risk, engineers may need to qualify an alternative rather than assume that any Class D or Class AB amplifier is pin compatible. This page consolidates the verified distributor specifications, lifecycle information, package details, sourcing links, practical application guidance, and an explicit assessment of replacement availability. It also separates documented parameters from missing technical data instead of presenting unverified electrical characteristics as guaranteed specifications.

RFQ Kontak
WM9701CPT Stereo Audio Codec | Texas Instruments
WM9701CPT

WM9701CPT Stereo Audio Codec | Texas Instruments

The Texas Instruments WM9701CPT is a stereo audio codec with an integrated analog audio channel and digital audio interface, supplied in a 28-pin TQFP package. The verified distributor data identifies it as an Audio Special Purpose / Audio Channel device and lists an LCSC starting price of $0.6762. Its primary role is converting digital audio data into analog stereo signals while supporting audio-system signal conditioning and analog output control. The package designation CPT identifies a 28-pin TQFP-compatible physical format, but detailed electrical limits, supported sample rates, interface modes, analog performance, and pin functions are not present in the supplied verification records. A codec is an audio interface integrated circuit that combines digital-to-analog conversion, analog signal paths, and control or communication functions. In the broader semiconductor hierarchy, an audio codec belongs to an audio interface IC, then to an interface IC and a mixed-signal semiconductor. This integration can reduce the number of separate converters and support components in consumer audio, communications, and embedded systems. For the WM9701CPT, however, the supplied data does not establish whether its digital interface is I2C, I2S, or another format, nor does it quantify the number of supported channels. The verified records provide three useful procurement anchors: DigiKey Marketplace lists WM9701CPT for purchase and shipment, Octopart identifies availability and pricing across two distributors, and LCSC lists the part as in stock from $0.6762. A separate distributor listing describes the device as an analog consumer audio/video IC. These sources support commercial availability, but they do not provide manufacturer lifecycle status, operating temperature, supply voltage, clock requirements, DAC resolution, SNR, THD, output impedance, or pin-level mapping. WM9701CPT is best evaluated as a legacy or inventory-dependent audio codec rather than assumed to be a currently designed modern USB audio solution. Before schematic release, an engineer should obtain the original manufacturer datasheet and confirm the CPT land pattern, exposed-pad requirements, digital interface, analog routing, clocking, and firmware or register expectations. The part number alone is not enough to establish drop-in compatibility or modernization safety. Potential audio applications include legacy consumer-audio systems, portable media equipment, communications terminals, and embedded products that already target this codec family. Such uses remain conditional because the supplied data does not verify operating conditions or signal paths. Component selection should be based on a complete datasheet review rather than the distributor category label. The main engineering risk is assuming that similarly named stereo codecs are interchangeable. Digital-interface timing, register maps, analog routing, package dimensions, exposed-pad treatment, and software initialization can differ even when the functional description is similar. Validate the replacement against the original schematic and PCB footprint before committing to an alternative. This page consolidates the verified distributor listings, separates confirmed procurement facts from missing technical data, and avoids inventing specifications, pin assignments, or drop-in replacements. Obtain the authoritative datasheet before layout release or production substitution.

RFQ Kontak
WM9707SCFT/V - Stereo AC'97 Audio Codec | Cirrus Logic
WM9707SCFT/V

WM9707SCFT/V - Stereo AC'97 Audio Codec | Cirrus Logic

The Cirrus Logic WM9707SCFT/V is a stereo AC'97 revision 2.1 audio interface codec with one ADC, one DAC, 18-bit serial audio resolution, and S/PDIF output in a 48-pin 7 x 7 mm TQFP package. It combines analog audio conversion with digital AC'97 audio connectivity for legacy computer, communications, and embedded audio systems. An audio codec is an interface IC that converts analog sound into digital samples and digital audio streams into analog signals. The WM9707SCFT/V belongs to the AC'97 audio codec category within interface ICs and broader semiconductor signal-processing devices. Its digital interface supports communication between an audio codec and a host controller, while its analog inputs and outputs handle microphones, line-level sources, headphones, or powered speakers through external circuitry. The WM9707SCFT/V provides stereo conversion through one ADC and one DAC, with an 18-bit serial format identified in the product listing. It also includes S/PDIF output, allowing digital audio to leave the codec over a standardized digital interface. The 48-pin TQFP package provides the mixed-signal, digital-interface, clock, and power connections required for a complete stereo codec implementation. AC'97 revision 2.1 support makes this device relevant to legacy PC audio architectures, industrial control panels, embedded systems, and communications equipment that already use the AC'97 bus. Designers should treat clocking, analog grounding, input and output coupling, and digital signal return paths as central design considerations. Because the AC'97 interface is a mature architecture, it is most appropriate for new designs when its electrical and software compatibility have been confirmed against the complete system requirements. Typical uses include stereo line-input processing, microphone conditioning through external analog circuits, multimedia playback, industrial operator consoles, and embedded equipment that accepts an AC'97-compatible codec. The S/PDIF output can feed a downstream digital audio receiver, while the analog DAC output supports conventional amplified playback when paired with suitable output circuitry. A successful implementation requires stable analog and digital supplies, correct master-clock and bit-clock relationships, input and output filtering, and careful separation of analog and return currents. The component also requires PCB space for decoupling and signal routing around a 48-pin mixed-signal package. Confirm the complete pin-description table and application circuit in the manufacturer datasheet before assigning nets or making a board revision. This product page consolidates the identified codec architecture, package details, sourcing information, comparison points, and practical integration guidance. It emphasizes the verified AC'97, ADC, DAC, resolution, S/PDIF, and package characteristics that determine whether the WM9707SCFT/V fits an existing audio system.

RFQ Kontak
WPC8763LDG - Embedded Controller IC QFP-128 | Winbond
WPC8763LDG

WPC8763LDG - Embedded Controller IC QFP-128 | Winbond

The Winbond Electronics WPC8763LDG is a specialized embedded controller (EC) integrated circuit supplied in a 128-pin QFP surface-mount package, designed primarily for notebook PC and mobile-system platform management applications such as keyboard scanning, power sequencing supervision, and thermal/fan control. An embedded controller is a specialized microcontroller that operates semi-independently of the host CPU to manage low-level platform functions. In the PC system hierarchy, the EC sits below the main CPU and chipset (PCH) as a power-management IC tier: it handles keyboard matrix scanning, battery charging supervision, thermal monitoring, fan speed control, and lid/power-button events, typically following Intel or AMD platform EC firmware specifications such as those used with ACPI and eSPI/KBC interfaces. The WPC8763LDG belongs to Winbond's WPC876x family of embedded controllers, which integrates an 8-bit or proprietary MCU core with on-chip flash/ROM program memory, keyboard controller (KBC) logic, GPIO, PWM channels for fan control, and ADC inputs for thermal and voltage monitoring. Key differentiating features of this family include the high GPIO count required for notebook keyboard matrices, integrated PWM fan controllers that reduce external component count, and low standby power consumption for battery-operated systems. The 128-pin QFP package provides sufficient I/O for a full notebook EC implementation on a single chip. Architecturally, EC devices like the WPC8763LDG combine a low-power MCU core, a shared RAM region, dedicated peripheral blocks (PS/2 keyboard interface, SMBus/I2C masters for battery and thermal IC communication, pulse-width modulators, and watchdog timers), and boot ROM. Firmware executes from internal non-volatile memory, and the EC communicates with the chipset over LPC or eSPI buses depending on platform generation. Typical applications include laptop and notebook motherboard EC functions, keyboard/mouse controller emulation (PS/2 KBC/Mouse), battery charging management in coordination with a charger IC, thermal and acoustic (fan) management, and general-purpose GPIO expansion in portable and industrial embedded systems. A key design consideration is firmware compatibility: the EC must run BIOS-coordinated firmware, so replacing this device requires both hardware pin compatibility and firmware/toolchain support - verify code image compatibility before any substitution. This page synthesizes distributor stock and pricing data, package information, and sourcing guidance not consolidated in the manufacturer's public datasheet listing.

RFQ Kontak
WT:A - Micron 48Gb LPDDR4 SDRAM Mobile Memory | Micron
WT:A

WT:A - Micron 48Gb LPDDR4 SDRAM Mobile Memory | Micron

Micron Technology MT53E1536M32D4DT-046 WT:A is a 48 Gbit Mobile LPDDR4 SDRAM memory IC in the MT53E family, rated at 2.133 GHz and supplied in a 200-ball TFBGA. According to DigiKey listing data retrieved on 2026-10-09, the part is a Mobile LPDDR4 device intended for high-density, low-power system designs that require the bandwidth of LPDDR4 with the smallest possible PCB footprint. What is an LPDDR4 SDRAM? LPDDR4 (Low-Power Double Data Rate 4) is a JEDEC-standardized volatile memory category optimized for mobile and power-constrained applications. Compared with LPDDR3 and DDR3/DDR4, LPDDR4 uses a low-swing I/O interface (V<sub>DDQ</sub> typically 1.1 V), 2n-prefetch architecture, and deep power-down modes, positioning it within the broader mobile memory hierarchy: LPDDR4 -> SDRAM -> volatile memory -> memory IC -> semiconductor. LPDDR4 is the memory type used in virtually every high-end smartphone application processor, and is increasingly adopted in automotive infotainment, edge AI, and ultra-thin notebooks. Key features of this 48 Gbit MT53E1536M32D4DT-046 WT:A device include a 1536M x 32-bit logical organization, 2.133 GHz data rate per the -046 speed-bin suffix, and operation from a low-voltage core rail to maximize battery life. The 200-ball TFBGA package is thin-profile and thermally efficient, suiting space-limited mobile platforms. The device supports the standard LPDDR4 command set including multi-channel operation, low-power states (IDD2N, IDD3P, IDD6), and on-die temperature sensing. The architecture follows Micron's 1y-nm-class mobile DRAM process, enabling a high-density 48 Gbit monolithic die. Combined with the -046 speed grade, this delivers the throughput needed for multi-camera image pipelines, 4K video encode/decode buffers, and large neural network inference workloads running on the application processor. The wide 32-bit datapath keeps channel-count low, simplifying PCB routing on highly integrated SoCs. Typical applications include flagship smartphone application processors, ultra-thin notebook main memory, automotive infotainment platforms, edge AI inference accelerators, AR/VR headset compute modules, and embedded single-board computer platforms. The wide temperature support and small form factor make it attractive in any design that demands high memory density with low standby power. When designing with the MT53E1536M32D4DT-046 WT:A, ensure the host SoC's LPDDR4 PHY matches the 2.133 GHz speed bin to avoid down-training. Decoupling and PCB stack-up should follow the Micron LPDDR4 design guide, with controlled-impedance routing for the CA and DQ byte lanes and matched lengths within each byte group. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on a one-line distributor listing.

RFQ Kontak
X9313UST1 - 50kΩ 32-Tap Digital Potentiometer SOIC-8 | Renesas
X9313UST1

X9313UST1 - 50kΩ 32-Tap Digital Potentiometer SOIC-8 | Renesas

The Renesas X9313UST1 is a digitally controlled potentiometer (XDCP™) housed in an 8-pin SOIC package with a fixed end-to-end resistance of 50 kΩ and 32 resistive taps. It provides a single-channel, non-volatile, up/down wiper interface through three logic input pins (U/D, INC, CS) and stores the last wiper position through on-chip nonvolatile memory that retains setting across power cycles. The 32-tap resolution gives approximately 1.0% per-step resolution across the resistor array. Background context: a digital potentiometer (often abbreviated "digi-pot") is a solid-state, semiconductor replacement for a mechanical potentiometer or trim pot. Digi-pots sit within the broader data-acquisition and analog-signal-conditioning hierarchy, alongside DACs and digital rheostats, and they belong to the Renesas XDCP™ family. Unlike mechanical pots, they are programmable by host firmware, never wear from mechanical actuation, and ship in surface-mount packages suitable for reflow soldering and dense PCB layouts. Key features include a low 1 mA (typical) standby current, terminal voltages up to ±5 V across the resistor array, a 1.0% end-to-end resistance tolerance, and a wiper current rating up to approximately ±1 mA continuous, with peak surge handling to 10 mA. The 3-wire serial interface consumes only three MCU GPIO pins and is compatible with 5 V logic. The internal architecture pairs a polysilicon resistor array with CMOS wiper switches and a non-volatile memory cell that latches the last wiper position before power-down. Three control inputs (CS, INC, U/D) implement a step-and-direction interface: CS enables the chip, INC clocks each tap step, and U/D selects up or down direction. Power-on recall places the wiper on the stored value with deterministic behavior. Typical applications are audio volume/balance control, LCD contrast/brightness trimming, programmable voltage references, sensor calibration, and parameter-set storage where an MCU must hold a setting through power-down. Because the wiper retains state without external EEPROM, designers can eliminate a serial EEPROM and reduce BOM cost in many calibration circuits. When designing with the X9313UST1, respect the maximum terminal voltage (±5 V across the resistor terminals) and verify that pin 8 is correctly identified in PCB layout - the part is widely second-sourced and a small number of look-alike 8-pin digi-pots swap the GND and VL pin positions. Add a 0.1 µF decoupling capacitor close to the supply pin and confirm that CS is not allowed to float. This page combines the Renesas datasheet specifications, current distributor pricing, pin-compatible cross references, and practical layout notes not always covered in the original datasheet, providing engineers a single-page engineering brief for the X9313UST1.

RFQ Kontak
XA2S200E-6FT256I - 200K Gate FPGA | AMD | 256-FTBGA
XA2S200E-6FT256I

XA2S200E-6FT256I - 200K Gate FPGA | AMD | 256-FTBGA

The AMD XA2S200E-6FT256I is a member of the Spartan-IIE XA family of Field Programmable Gate Arrays (FPGAs), designed for automotive and industrial applications requiring high performance, abundant logic resources, and a rich feature set at a low cost. This device provides 200,000 system gates, 5,292 logic cells, and 1,176 Configurable Logic Blocks (CLBs), operating from a nominal 1.8V supply. It is housed in a 256-ball FTBGA (17x17 mm) package with 182 user I/O pins. An FPGA (Field Programmable Gate Array) is an integrated circuit that can be configured by the customer or designer after manufacturing—hence "field-programmable." FPGAs are part of the broader programmable logic device (PLD) family, which sits above ASICs in flexibility but below them in unit cost at high volume. The Spartan-IIE family is a superior alternative to mask-programmed ASICs, avoiding the initial cost, lengthy development cycles, and inherent risk of conventional ASICs. FPGA programmability permits design upgrades in the field with no hardware replacement necessary. Key features of the XA2S200E-6FT256I include 57,344 total RAM bits, support for 1.71V to 1.89V supply voltage, and a -40°C to 100°C junction temperature range. The device uses a 0.15-micron CMOS process and supports I/O standards including LVCMOS, LVTTL, and HSTL. The -6 speed grade indicates a maximum internal clock frequency of approximately 200 MHz, suitable for moderate-speed control and data processing tasks. Technically, the Spartan-IIE architecture combines a configurable logic fabric with block RAM and dedicated routing resources. The 256-ball FTBGA package provides excellent thermal and electrical performance, with a compact 17x17 mm footprint. The device is lead-free and RoHS compliant, meeting modern environmental standards. Typical applications include automotive infotainment, motor control, industrial networking, and test equipment. The 182 I/O pins allow flexible interfacing with sensors, ADCs, and communication transceivers. The wide temperature range and automotive qualification make it suitable for under-hood and harsh-environment deployments. When designing with this FPGA, ensure adequate decoupling on the 1.8V core supply and separate I/O supply rails. The device is now obsolete (EOL), so plan for last-time buy or consider pin-compatible alternatives for new designs.

RFQ Kontak